TomTom ONE

Whats in the box

EasyPortTM mount

Car Charger

RDS-TMC Traffic Receiver*

Documentation pack

USB cable
* Not included with all products.

Getting started

Install your TomTom ONE in your car following the instructions on the installation poster at the start of this book. To switch on your TomTom ONE, press and hold the On/Off button for 2 seconds. The first time you switch on your device, it may take a short while to start. You have to answer a few questions to set up your device.

Having problems?

In rare cases, your ONE may not start correctly or may stop responding to your taps. First, check that the battery is charged properly. To fully charge the battery, you need to charge it for at least 2 hours. If this doesnt work, you can reset your device. To do this, press and hold the Power button for fifteen seconds. Release the Power button when device begins to restart.

Charging your TomTom ONE

Before you use your ONE for the first time, its a good idea to charge it fully using the home charger, which takes about 2 hours. There is no charging light on your ONE. To check the battery status and see when your ONE is charging, switch on your device and tap the bottom righthand corner of the screen in the Driving View. The battery status is shown on the next page.

Improving reception

If your TomTom ONE takes longer than 5 minutes to find your current position, make sure that the device is in an open space away from tall objects such as buildings or trees. When you connect your TomTom ONE to your computer, you can use TomTom HOME to download information about GPS satellite positions during the next 7 days. This helps your ONE to find your position faster. Important: Some vehicles have heat reflective shielding in the windshield. This may prevent your ONE from locating your current position.
Take care of your TomTom ONE
Never leave your TomTom ONE or accessories in view when you leave the car or they may become an easy target for thieves.
You can set a password for your TomTom ONE which must be entered every time you start your ONE. It is important to take care of your ONE. Your ONE is not designed for use in extreme temperatures and any such exposure may cause permanent damage. Do not open the casing of your ONE under any circumstances. Doing so may be dangerous and will invalidate the warranty. Wipe or dry the screen of your ONE using a soft cloth. Do not use any liquid cleaners.

Driving View

When your TomTom ONE starts, you are shown the Driving View along with detailed information about your current location. Tap the center of the screen at any time to open the Main Menu. Note: The Driving View is shown in black and white until your ONE locates your current position.
A Tap + and - to zoom in and out. B Your current position. C The name of the next major road or road sign information, if applicable. D Traffic bar - requires an RDS-TMC Traffic Receiver (available as an accessory). E Navigation instruction for the road ahead. Tap this area to repeat the last spoken instruction and to change the volume. F The name of the street you are on. G Information about your trip such as trip time, remaining distance and arrival time. To change the information shown, tap Status bar preferences in the Preferences menu. H GPS signal strength.

Making your first trip

Planning a route with your TomTom ONE is easy. To plan your first route, follow the steps below. Important: You should always plan your journey before you start driving. It is dangerous to plan a route while driving. 1. Tap the screen to bring up the main menu. Note: The buttons on your ONE are shown in full color unless a button is currently unavailable. For example, the button named Find alternative. in the Main Menu is not available until you have planned a route. 2. Tap Navigate to.

3. Tap Address.

When you enter an address, you can choose from the following options: City center - tap this button to set your destination as the center of a city or town. Street and house number - tap this button to set an exact address as your destination. ZIP code - tap this button to enter a ZIP code as your destination. Note: You can enter a ZIP code for any country. In the UK and the Netherlands, ZIP codes are detailed enough to identify a house on their own. In other

countries you can enter a ZIP code to identify a town or area. You will then have to enter a street and house number. Cross street or intersection - tap this button to set your destination as the point where two streets meet. In this example, we will enter an exact address. 4. Tap Street and house number.
Note: When planning a trip for the first time your ONE asks you to choose a country. Your choice is saved and used for all routes you plan. You can change this setting at any time by tapping the country flag. 5. Start to type the name of the town where you want to go.
As you type, the names of the towns that match what you have typed are shown. When your destination appears in the list, tap the name of the town to set the destination. 6. Start to type the name of the street and select it when it is shown. As with the name of the town, the names of the streets that match what you have typed are shown. When your destination appears in the list, tap the name of the street to set the destination. 7. Now enter the house number of your destination and then tap Done.
8. Your ONE asks if you need to arrive at a particular time. For this exercise, tap NO.
The route is calculated by your ONE. 9. When the route has been calculated, tap Done. Your ONE will immediately begin to guide you to your destination, using both spoken instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom ONE asks you if you need to arrive at a particular time. Tap YES to enter a preferred arrival time. Your ONE calculates your arrival time and shows you whether you will arrive on time. You can also use this information to work out when you need to leave. If your ONE shows that you will arrive 30 minutes early, you can wait and leave in 30 minutes time, rather than arrive early. Your arrival time is constantly recalculated during your trip. The status bar shows whether you will arrive on time or if you are going to be late, as shown below: You will arrive 55 minutes before the arrival time you entered. If the estimated arrival time is more than five minutes before the time you entered, it is shown in green. You will arrive 3 minutes before the arrival time you entered. If the estimated arrival time is less than 5 minutes before the time you entered, it is shown in yellow. You will arrive 19 minutes late. If the estimated arrival time is later than the time you entered, it is shown in red. Tap Status bar preferences in the Preferences menu, to enable or disable arrival time notifications.

Options

Use your TomTom ONE to find the location of a service and the contact details.

Phone for help

Emergency services Emergency breakdown services Nearest police station Nearest doctor Nearest hospital Nearest public transport Nearest car repair services Nearest dentist Nearest pharmacy Nearest vet Note: In some countries, information may not be available for all services. Use your TomTom ONE to navigate your way by road to a service center. Nearest car repair services Nearest hospital Nearest doctor Nearest police station Nearest pharmacy Nearest dentist Note: In some countries, information may not be available for all services. Use your TomTom ONE to navigate your way on foot to a service center. Nearest gas station Nearest public transport Nearest police station Nearest pharmacy Home Nearest doctor Note: In some countries, information may not be available for all services. Your TomTom ONE shows your current location. You can then tap Phone for help to select the type of service you want to contact.

Drive to help

Walk to help

Where am I?

Tap this button to read the British Red Cross First Aid guide.

First Aid Guide

Tap this button to read a selection of useful guides.

Other guides

Favorites

What are Favorites?

Favorites are places that you often visit. You can create Favorites so that you dont have to enter the address every time you want to navigate there. They dont have to be places you especially like, just useful addresses.
How can I create a Favorite?
From the Main Menu, tap Add Favorite. Note: The button Add Favorite may not be shown on the first page of the Main Menu. Tap the arrow to open other pages in the Main Menu. You can then select the location of the Favorite from the list below. Give your Favorite a name that is easy to remember. Your ONE will always suggest a name, usually the address of the Favorite. To enter the name, just start typing. You dont have to delete the suggested name. You can set your Home location as a Favorite.
You cannot create a Favorite from another Favorite. This option will always be unavailable in this menu. To rename a Favorite, tap Manage Favorites in the Preferences menu.
You can specify an address to be a Favorite. When you enter an address, you can choose from four options. City center Street and house number ZIP code Crossing or intersection
Select a Favorite location from a list of places you have recently used as destinations.
You can add a Point of Interest (POI) as a Favorite. Does it make sense to do this?
If you visit a POI you particularly like, for example a restaurant, you can add it as a Favorite. To add a POI as a Favorite, tap this button, then do the following: 1. Narrow your choice of POIs by selecting the area where the POI is. You can select one of these options: POI near you - to search from a list of POIs near your current position. POI in city - to choose a POI in a particular town or city. You have to specify a town or city. POI near Home - to search from a list of POIs near your Home location. If you are currently navigating to a destination, you can also select from a list of POIs which are on your route or near your destination. Choose one of these options: POI along route POI near destination 2. Select the category of POI. Tap the category of POI if it is shown or tap the arrow to choose from the complete list. Tap Any POI category to search for a POI by name. Tap this button to add your current position as a Favorite. For example, if you stop somewhere interesting, while you are there you can tap this button to create the Favorite.

My location

Tap this button to create a Favorite using the map browser. Select the location of the Favorite using the cursor, then tap Done.
Tap this button to create a Favorite by entering latitude and longitude values.
Tap this button to select your last recorded position as your destination.
How can I use a Favorite?
You will normally use a Favorite as a way of navigating to a place without having to enter the address. To navigate to a Favorite, do the following: 1. Tap the screen to bring up the main menu. 2. Tap Navigate to. 3. Tap Favorite. 4. Select a Favorite from the list. Your ONE calculates the route for you. 5. When the route is calculated, tap Done. Your ONE will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen.
How can I change the name of a Favorite?
1. Tap the screen to bring up the main menu. 2. Tap Change preferences to open the Preferences menu. 3. Tap Manage Favorites. 4. Tap the Favorite you want to rename. 5. Tap Rename.
How can I delete a Favorite?
1. Tap the screen to bring up the main menu. 2. Tap Change preferences to open the Preferences menu. 3. Tap Manage Favorites. 4. Tap the Favorite you want to delete. 5. Tap Delete.

Browse map

To look at the map in the same way as you might look at a traditional paper map, tap Browse map in the Main Menu. You can move the map by touching the screen and moving your finger across the screen.
A The scale bar B Your current position. C GPS button Tap this button to center the map on your current position. D Options E The cursor F The Find button Tap this button to find specific addresses. G The Cursor button Tap this button to navigate to the cursor position, make a Favorite of the cursor position, or find a Point of Interest near the cursor position. H The zoom bar Zoom in and out by moving the slider.

Cursor button

You can use the cursor to find addresses and Points of Interest (POIs), for example, restaurants, train stations and gas stations.
Position the cursor over a location on the map, then tap one of the following buttons: Tap this button to navigate to the cursor position. Your ONE will calculate the route.

Navigate there

Tap this button to find a POI near the cursor position. For example, if you have found a restaurant to go to, you can search for a parking garage nearby.

Find POI nearby

Tap this button to bring the location currently highlighted by the cursor to the center of the screen when looking at the map.

Center on map

Tap this button to create a Favorite at the cursor position.

Add as Favorite

Tap this button to correct the location shown at the cursor position.

Correct location

Points of Interest
Points of Interest or POIs are useful places on the map. Here are some examples: Restaurants Hotels Museums Parking garages Gas stations

Navigating to a POI

You can use a POI as your destination. For example, if you are traveling to an unfamiliar city, you could choose a POI to help find a parking garage. 1. Tap the screen to bring up the main menu. 2. Tap Navigate to. in the Main Menu. 3. Tap Point of Interest. 4. Tap POI in city. 5. Narrow your choice of POIs by selecting the area where the POI is located. You can select one of these options: POI near you - to choose from a list of POIs near to your current location. POI in city - to find a POI in a particular town or city. POI near Home - to choose from a list of POIs near to your Home location. You can select from a list of POIs which are along your route or close to your destination. Choose from one of these options: POI along route POI near destination Note: The last POI you viewed is also shown so that you can plan a route there more quickly. 6. Type the name of the town you want to visit and select the town when it appears in the list. 7. Select the category of POI: Tap Any POI category to search for a POI by category name. Tap the category of POI, if it is shown.
Tap the arrow to choose from the complete list of categories. Select the category from the list or start to type the name of the category and select it when it appears in the list. 8. Tap Parking garage. 9. From the list of POIs shown, select the POI you want to navigate to. The table below explains the distances listed next to each POI. POI near you POI in city POI near Home POI along route POI near destination Distance from your current location Distance from the city center Distance from your Home location Distance from your current location Distance from your destination

If you know the name of the POI, tap Find and type the name. Select it from the list when it is shown. The next screen shows more detailed information including the location of the POI on the map and the phone number of the POI, if available. Tap Select to confirm you want to plan a route to this POI. Once you have selected a POI, the route to the POI is calculated by your TomTom ONE.

Showing POIs on the map

1. Tap Show POIs on map in the Preferences menu.

Show POI on map

2. Select the POI categories to display on the map. Tap Find to search for a POI by name. 3. Tap Done. The POIs you have selected are shown as symbols on the map.
How can I set warnings for POIs?
1. Tap the screen to bring up the main menu. 2. Tap Change preferences. 3. Tap Warn when near POI.
Tap this button to receive a warning when you travel near to the location of a POI.

Warn when near POI

4. Select the category of POI you want to be warned about. Select the category from the list or start to type the name of the category and select it when it is shown in the list. 5. Set how close the POI should be when you receive a warning. 6. Choose the warning sound for the category of POI you selected.

Preferences

Use night colors / Use day colors
Tap this button to reduce the brightness of the screen and show darker colors on the map. When should I use this?

Use night colors

When its dark, it is easier to see the screen if the display on your ONE is not brightly lit. To change back to a brighter screen showing brighter colors on the map, tap Use day colors.

Use day colors

Tap this button to set which categories for the Points of Interest (POIs) should be shown on the map: 1. Tap Show POIs on map in the Preferences menu.
2. Select the POI categories to display on the map. Tap Find to search for a POI category. 3. Tap Done. The POIs you have selected are shown as symbols on the map.

Safety preferences

Tap this button to set the following safety preferences: Hide most menu options while driving
Suggest driving breaks Show safety reminders Warn when near places of worship or schools Warn when driving faster than allowed Warn when driving faster than a set speed Warn not to leave the device in the car If you select one or more of the warnings, you will also be asked to select a sound to be played whenever a warning is displayed. Select whether or not your TomTom ONE should warn you about which side of the road you should be driving on. Decide if you want the map display to be turned off in special circumstances and press Done. What happens when I use the Turn off map display option? When you turn off the map display, instead of seeing your position on a map in the Driving View, you will only see information about the next instruction. Tap the button and select an option for when the map should be turned off. These are the options: Always - The map will not be shown and you will only see information about the next instruction and arrows showing direction. Above a certain speed - you set the speed at which point the map will be turned off. This option is useful for situations when the map might be distracting, such as when you are driving fast. Never - the map is never turned off.

Name preferences

Tap this button to set the information that is shown on the map in the Driving View. The following options are available: Show house number before street name
Show street names - if you are using a computer voice for spoken instructions and have selected that street names should be read aloud, you do not need to select this option, since the street names will be read aloud even though this option is not selected. Show next highway / signpost - when this option is selected, the next major road on your route is shown at the top of the screen in the Driving View. Show current street name on map

Change Home location

Tap this button to set or change your Home location.
Do I need to use my actual home address for the Home location? No. Your Home location can be a place you go often, for example, your office. It can be your actual home address, but it can also be any address you like. Why should I set a Home location? Having a Home location means that you have a quick and easy way to navigate there, by tapping the Home button in the Navigate to. menu

Manage maps

Tap this button to do the following: Download a map - tap this button to download a map you have bought using TomTom HOME. It may not be possible to download maps on all devices. Switch map - tap this button to change the map you are using. Download free map corrections - tap this button to download map corrections provided as part of the Map Share service. Delete a map - tap this button to delete a map. This might be necessary to create more space on your ONE, for example when you want to load a different map. Note: Dont delete a map unless you have already made a backup of the map. If you delete a map before you make a backup, you will no longer be able to load the map on your ONE. Use TomTom HOME to make backups, download, add and delete maps from your navigation device.

Planning preferences

Tap this button to set the kind of route planned when you select a destination. The following options are available:
Ask me every time I plan Always plan fastest routes Always plan shortest routes Always avoid freeways Always plan walking routes Always plan bicycle routes Always plan for limited speed You can then set if the route summary screen closes automatically after you have planned a route. If you select No, you have to tap Done to close the route summary screen.

Change language

Tap this button to change the language used for all the buttons and messages you see on your ONE. You can choose from a wide range of languages. When you change the language, you are also given the opportunity to change the voice.

Set owner

Tap this button to enter your name and address as the owner of your ONE and to change or delete a 4-digit password for your ONE.
Note: You can only change or delete a 4-digit password on your TomTom ONE. You can create a 4-digit password for your ONE using TomTom HOME: 1. Connect your ONE to your computer and turn on your ONE and your computer. TomTom HOME starts automatically. 2. Click on Operate my ONE in TomTom HOME. Your ONE appears and can be controlled using TomTom HOME. 3. From the Main Menu, click Change preferences. 4. Click Set Owner. You can now set a 4-digit password for your ONE. You can only create a 4-digit password using TomTom HOME.
Operate left-handed / Operate right-handed
Tap this button to move important buttons, for example, the Done and Cancel buttons as well as the zoom bar, to the left hand side of the screen. This makes it easier to tap the buttons with your left hand without blocking the screen.

Operate lefthanded

To move the buttons back to the right hand side of the screen, tap Operate right-handed.

Brightness preferences

Tap this button to set the brightness of the screen. Move the sliders to set the brightness separately for day map colors and for night map colors.
You can set the map color scheme by tapping Change map colours.

Change map colors

Tap this button to select the color schemes for day and night map colors. You can also download more color schemes from TomTom Services.

Set units

Tap this button to set the type of units that will be shown for the following: Distance
Time Latitude and longitude Temperature Air pressure

Set clock

Tap this button to select the type of clock that is shown and set the time. The easiest way to set the time is by tapping the Sync button. Your ONE will then take the time from GPS information.
Note: After using Sync to set the time, you may have to adjust the hours depending on your time zone. Your ONE works out your time zone and always keeps the time correct using GPS information. You can only use Sync if you have GPS reception, so you cannot set the clock in this way when you are indoors.

Keyboard preferences

You use the keyboard to enter your destination or to find an item in a list, such as a POI. Tap this button to select the size of the keys on the keyboard and the keyboard layout. You can select from two sizes: Large keyboard Small keyboard Three keyboard layouts are available: ABCD keyboard QWERTY keyboard AZERTY keyboard

Making a map update

1. Tap Map corrections in the Main Menu. 2. Tap Correct a map error.

Correct a map error

A list of possible map updates is shown. 3. Select the type of update you want to report. Note: If you tap Add missing POI or Report other error you will be asked for some additional information before the next step. 4. Select the method you want to use for selecting the location of the update. 5. When you have found the location, tap Done. 6. Enter update or confirmation of update now.
Receiving the latest map updates
When you connect your TomTom ONE to your computer, TomTom HOME automatically downloads any available map updates and sends any changes you have made, to the Map Share community. There are several types of updates which can be set in the Correction preferences menu.
Marking a map error while on the move
If you notice an item on your map that needs attention, you can mark the location using the Report button and then enter the details when you are no longer driving. To show the Report button in the Driving View, do the following: 1. Tap Map corrections in the Main Menu. 2. Tap Correction preferences. 3. Tap Done and then tap Done again. 4. Select Show report button, then tap Done. The Report button is shown on the left-hand side of the Driving View. After you mark a location, you can add more information about the change when you open the Map corrections menu. For example, you are driving to a friend's house and you notice that the name of the street you are on is different from the one on your map. To report the change, tap the Report button and your ONE will save your current location. You can then send the update to TomTom Map Share when you have finished your trip.
TomTom Map Share community
To join the Map Share community, do the following: 1. Tap Map corrections in the Main Menu. 2. Tap Download corrections made by others. 3. Tap Join.
When you connect your TomTom ONE to computer, TomTom HOME automatically downloads any available map updates and sends any changes you have made, to the Map Share community.
Changing my preferences for map updates
Correction preferences is used to set the way TomTom Map Share runs on your device. You can set the following preferences: Choose what types of updates you want to use on your maps. Decide if you want to share your updates with others. Show or hide the Report button in the Driving View. To set your preferences, do the following: 1. Tap Map corrections in the Main Menu. 2. Tap Correction preferences. A list of update types is shown. 3. Tick the box next to each update type you want use. 4. Tap Done. 5. Choose how you want to share your map updates with the Map Share community, then tap Done. 6. Choose if you want to see the Report button in the Driving View. 7. Tap Done. Tip: If you later decide you want to remove updates from the map, clear the checkbox next to the types of update you want to remove. If you clear all the checkboxes, your map returns to the original state before the first update.

Map update categories

There are several types of update that you can make to a map.
To make an update to your map, tap Map corrections in the Main Menu then tap Correct a map error. The following types of updates are shown. Tap this button to block or unblock a street. You can block or unblock the street in one or both directions.

(Un)block street

For example, to correct a street near to your current location, do the following: 1. Tap (Un)block street. 2. Tap Near you to select a street near your current location. You can select a street by name, a street near your Home location or a street on the map. 3. Select the street or section of a street you want to correct by tapping it on the map. The street you select is highlighted and the cursor shows the name of the street. 4. Tap Done. Your device shows the street and whether the traffic is blocked or allowed in each direction:
5. Tap one of the direction buttons to block or unblock the flow of traffic in that direction. 6. Tap Done. The next time you connect your device to TomTom HOME, your updates are shared with the TomTom Map Share community. Tap this button to correct the traffic direction of a one-way street, where the direction of traffic is different to the direction shown on your map.
Reverse traffic direction
Note: Reverse traffic direction only works for one-way streets. If you select a two-way street you will be given the chance to block/unblock the street rather than changing the direction.
Tap this button to change the name of a street on your map.

vabckc sdn vk fbks sdjv

For example, to rename a street near to your current location: 1. Tap Edit street name. 2. Tap Near you. 3. Select the street or section of a street you want to correct by tapping it on the map. The street you select is highlighted and the cursor shows the name of the street. 4. Tap Done. 5. Type the correct street name. 6. Tap Done. Tap this button to change and report incorrect road turn directions.

Edit street name

Change turn restrictions
Tap this button to change and report road speed limit.

Change road speed

Tap this button to add a new Point of Interest (POI). For example to add a new restaurant near to your current location:

Add missing POI

1. Tap Add missing POI. 2. Tap Restaurant in the list of POI categories. 3. Tap Near you. 4. Select the location of the missing restaurant. You can select the location by entering the address or by selecting the location on the map. Select Near you or Near home to open the map at your current location or at your Home location. 5. Tap Done. 6. Type the name of the restaurant then tap OK. 7. If you know the telephone number of the restaurant you can type it, then tap OK. If you dont know the number, just tap OK without typing a number.
Tap this button to edit an existing POI. You can use this button to make the following changes to a POI:

Edit POI

Delete the POI. Rename the POI. Change the telephone number of the POI. Change the category that a POI belongs to. Move the POI on the map. Tap this button to report other types of update. These updates are not immediately corrected on your map. Your TomTom ONE sends a special update report to TomTom Map Share.

Report other error

You can report missing streets, errors in freeway entrances and exits and missing roundabouts. If the update you want to report is not covered by any of these report types, enter a general description then tap Other.
Traffic Information using RDS-TMC
The Traffic Message Channel (TMC)
You can receive traffic information on your TomTom ONE using the TomTom RDS-TMC Traffic Receiver. The TMC transmits traffic information as a radio signal. Tip: The TomTom RDS-TMC Traffic Receiver is included with some products and available as an accessory for others. Visit tomtom.com for more information. The Traffic Message Channel (TMC) is not a TomTom Service. FM radio stations in several countries broadcast TMC information as part of their programming. TMC is also known as RDS-TMC traffic information. Your TomTom navigation device uses this information to warn you about traffic delays along your route and how you can avoid them. Note: TomTom is not responsible for the availability or quality of traffic information provided by TMC. TMC is not available in all countries or regions. Visit tomtom.com to check if it is available in your country or region.

FCC Information for the User
This product contains a transmitter which must not be co-located or simultaneously operated in conjunction with any other transmitter. Exposure to Radio Frequency Radiation This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 8 inches (20 cm) during normal operation.
Radio and Television Interference This equipment radiates radio frequency energy and if not used properly - that is, in strict accordance with the instructions in this manual - may cause interference to radio communications and television reception. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation distance between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Important This equipment was tested for FCC compliance under conditions that included the use of shielded cables and connectors between it and the peripherals. It is important that you use shielded cables and connectors to reduce the possibility of causing radio and television interference. Shielded cables suitable for the product range can be obtained from an authorised dealer. If the user modifies the equipment or its peripherals in any way, and these modifications are not approved by TomTom, the FCC may withdraw the users right to operate the equipment. For customers in the USA, the following booklet prepared by the Federal Communications Commission may be of help: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the US Government Printing Office, Washington, DC 20402. Stock No 004-000-00345-4.

TomTom ONE

Whats in the box
a Your TomTom ONE (Maps for US & Canada are preloaded in internal memory)
A Charging light B On/Off button C Reset button D Speaker E USB connector F RDS-TMC connector b Car charger c Documentation pack

d Windshield Holder

e USB cable
f Adhesive disk for windscreen mount

Before You Start.

Switching on and off
To switch your TomTom ONE on or off, press and hold the On/Off button for 2 seconds. The first time you switch on, it may take a short while for your device to start. Note: In rare cases, your ONE may not start correctly. If this happens, press the reset button, then switch on the device again.

Setting up

To set up your TomTom ONE you need to answer a few questions by tapping the screen. Important: Take care to select the correct language, since the language you choose will be used for all menus and written instructions.

Battery notes

For information on connecting your computer, see Using TomTom HOME (43). Note: Your TomTom ONE uses a small amount of battery power to remember the last screen being shown when the device is switched off. If you do not charge your ONE for a prolonged period of time, the next time you start your ONE it will show the default starting screen. All other device settings will still be maintained.

Improving reception

If your TomTom ONE takes longer than 5 minutes to find your current position, make sure that the device is in an open space away from tall objects such as buildings or trees. When you connect your TomTom ONE to your computer, you can use TomTom HOME to download information about GPS satellite positions during the next 7 days. This helps your ONE to find your position faster. Important: Some vehicles have heat reflective shielding in the windscreen. This may prevent your ONE from locating your current position.

Windshield Holder

Use the windshield holder to install your TomTom ONE inside your car. To attach the holder, press the suction cup firmly to the windshield in your car, in an area of the windshield where the glass is flat. Make sure that both the holder and your windshield are clean and dry before you attach the holder. Place the holder so that it does not interfere with your view of the road.
Take care of your TomTom ONE
Never leave your TomTom ONE or accessories in view when you leave the car or they may become an easy target for thieves. You can set a password for your TomTom ONE which must be entered every time you start your ONE. For more information, see Using TomTom HOME (43). It is important to take care of your ONE. Your ONE is not designed for use in extreme temperatures and any such exposure may cause permanent damage. Do not open the casing of your ONE under any circumstances. Doing so may be dangerous and will invalidate the warranty. Wipe or dry the screen of your ONE using a soft cloth. Do not use any liquid cleaners.

Driving View

When your TomTom ONE starts, you are shown the Driving View along with detailed information about your current location. Tap the center of the screen at any time to open the Main Menu. Note: The Driving View is shown in black and white until your ONE locates your current position.

Browse as images

Tap the screen to turn off the 3D display and view the map from above. Tap this button to see an overview of the route using the map browser. For more information about the map browser, see Driving View (5).

Browse map of route

Tap this button to watch a demo of the trip. You can interrupt the demo at any time by tapping the screen.

Show route demo

Tap this button to open the route summary screen.

Show route summary

Finding alternative routes
Once you have planned a route, you may want to change something about the route, without changing your destination.

Why change the route?

Maybe for one of these reasons: You can see a roadblock or a line of traffic ahead. You want to travel via a particular location, to pick someone up, stop for lunch or fill up with gas. You want to avoid a difficult intersection or a road you dont like. Tap Find alternative. in the Main Menu to change the route that is currently planned.

Find alternative.

Then tap one of the options below.
Tap this button to calculate an alternative to the route already planned.

Calculate alternative

Your ONE will look for another route from your current location to your destination. If you decide you would prefer to use the original route after all, tap Recalculate original. Why would I need to do this? Apart from the roads near your position and near your destination, the new route will use totally different roads to reach your destination. This is an easy way of calculating a totally different route. Tap this button if you can see a roadblock or a line of traffic ahead. You then have to choose how much of the route ahead you want to avoid.

Avoid roadblock

Choose from the different options: 100m, 500m, 2000m, 5000m. Your ONE will recalculate your route avoiding the section of the route for the distance you selected. Dont forget that once a new route is calculated, you may have to turn off the road you are on very soon. If the roadblock suddenly clears, tap Recalculate original to return to your original route.
Tap this button to change your route so that it passes a particular location, perhaps to pick someone up on the way.

Travel via.

You choose the location you want to pass in the same way as you choose a destination. So you can select from all the same options: for example, Address, Favorite, Point of Interest and Point on map. Your ONE will calculate a new route to your destination that passes the location you chose. Tap this button to return to the original route without deviations to avoid roadblocks or traveling via particular locations.

Cursor button

You can use the map to find addresses and Points of Interest (POIs), for example, restaurants, train stations and gas stations.
Tap the cursor button then tap one of the following buttons: Tap this button to navigate to the cursor position. Your ONE will calculate the route.

Navigate there

Tap this button to bring the location currently highlighted by the cursor to the center of the screen when looking at the map.

Center on map

Tap this button to create a Favorite at the cursor position. For more information about Favorites, see Favorites (18).

Add as Favorite

Points of Interest
Points of Interest or POIs are useful places on the map. Here are some examples: Restaurants Hotels Museums Parking garages Gas stations

Showing POIs on the map

1. Tap Show POIs on map in the Preferences menu.

Show POI on map

2. Select the POI categories to display on the map. Tap Find to search for a POI by name. 3. Tap Done. The POIs you have selected are shown as symbols on the map.

Navigating to a POI

You can use a POI as your destination. For example, if you are traveling to an unfamiliar city, you could choose a POI to help find a parking garage. 1. Tap the screen to bring up the main menu. 2. Tap Navigate to. in the Main Menu. 3. Tap Point of Interest. 4. Tap POI in city. 5. Narrow your choice of POIs by selecting the area where the POI is located. You can select one of these options: POI near you - to choose from a list of POIs near to your current location. POI in city - to find a POI in a particular town or city. POI near Home - to choose from a list of POIs near to your Home location.
You can select from a list of POIs which are along your route or close to your destination. Choose from one of these options: POI along route POI near destination 6. Type the name of the town you want to visit and select the town when it appears in the list. 7. Tap Parking garage. 8. Select the category of POI: Tap Any POI category to search for a POI by name. Tap the category of POI, if it is shown. Tap the arrow to choose from the complete list of categories. Select the category from the list or start to type the name of the category and select it when it appears in the list. 9. Select a parking garage. The distance listed next to each POI is the distance from the city center. 10.From the list of POIs shown, select the POI you want to navigate to. The table below explains the distances listed next to each POI. POI near you POI in city POI near Home POI along route POI near destination Last POI Distance from your current location Distance from the city center Distance from your Home location Distance from your current location Distance from your destination Distance to the last POI you visited

If you know the name of the POI, tap Find and type the name. Select it from the list when it is shown. 11.Select a parking garage. The distance listed next to each POI is the distance from the city center. Once you have selected a POI, the route to the POI is calculated by your TomTom ONE. The route to the POI is then calculated by your TomTom ONE.
How can I set warnings for POIs?
1. Tap the screen to bring up the main menu. 2. Tap Change preferences. 3. Tap Manage POIs. Note: The Manage POIs button is only available when all menu buttons are shown. To show all menu buttons, tap Show ALL menu options in the Preferences menu.
4. Tap Warn when near POI. Tap this button to receive a warning when you travel near to the location of a POI.

Warn when near POI

5. Select the category of POI you want to be warned about. Select the category from the list or start to type the name of the category and select it when it is shown in the list. 6. Set how close the POI should be when you receive a warning. 7. Choose the warning sound for the category of POI you selected.

Preferences

You can change the way your TomTom ONE looks and behaves. Tap Change preferences in the Main Menu.
Use night colors / Use day colors
Tap this button to reduce the brightness of the screen and show darker colors on the map. When should I use this?

Use night colors

When its dark, it is easier to see the screen if the display on your ONE is not brightly lit. To change back to a brighter screen showing brighter colors on the map, tap Use day colors.

Use day colors

Tap this button to set which categories for the Points of Interest (POIs) should be shown on the map. Select the POIs that you want to see on the map from the list.
When you select a POI, it is shown on the map using the symbol you can see next to each category in the list. To find a POI category quickly, tap Find, then start to type the name of the POI category. As soon as the category is shown in the list, you can select it. For more information about POIs, see Points of Interest (23).

Safety preferences

Tap this button to set the following safety preferences: Hide most menu options while driving
Suggest driving breaks Show safety reminders Warn when near places of worship or schools Warn when driving faster than allowed Warn when driving faster than a set speed Warn not to leave the device in the car If you select one or more of the warnings, you will also be asked to select a sound to be played whenever a warning is displayed. Select whether or not your TomTom ONE should warn you about which side of the road you should be driving on. Decide if you want the map display to be turned off in special circumstances and press Done. What happens when I use the Turn off map display option? When you turn off the map display, instead of seeing your position on a map in the Driving View, you will only see information about the next instruction. Tap the button and select an option for when the map should be turned off. These are the options: Always - The map will not be shown and you will only see information about the next instruction and arrows showing direction. Above a certain speed - you set the speed at which point the map will be turned off. This option is useful for situations when the map might be distracting, such as when you are driving fast. Never - the map is never turned off.
Turn off sound / Turn on sound
Tap this button to turn off spoken instructions. The button changes to Turn on sound. If you turn off the sound, warnings for upcoming POIs are also turned off.

Turn off sound

Tips To change the volume, tap Volume preferences in the Preferences menu. For more information, see Volume preferences (28). To change the volume quickly while you are driving, tap the bottom lefthand section of the Driving View and move the slider. To change the voice being used by your ONE, tap Change voice in the Preferences menu. For more information, see Selecting a voice (14).
Tap this button to change the volume for spoken instructions.

Manage Favorites

Tap this button to rename or delete Favorites. To find a Favorite quickly, tap Find, then start to type the name of the Favorite. As soon as the Favorite is shown in the list, you can select it.

Change map colors

Tap this button to select the color schemes for day and night map colors. You can also download more color schemes from TomTom PLUS.

Brightness preferences

Tap this button to set the brightness of the screen. You can set the brightness separately for day map colors and for night map colors.
You can set the map color scheme by tapping Change map colors. For more information, see Change map colors (30).
Tap this button to select the information shown on the status bar: Remaining time - the estimated time left until you reach your destination.
Remaining distance - the distance left until you reach your destination. Current time Arrival time - your estimated arrival time. Speed Direction Show next street name - the name of the next street on your trip. Show current street name Show leeway to arrival time - your ONE shows how late or early you will be compared with the preferred arrival time that is set during the planning of a route. Show max speed next to speed - only available when speed (above) is also selected. How should the status bar be displayed? Horizontal - If you choose this option, the status bar will be shown at the bottom of the Driving view. Vertical - If you choose this option, the status bar will be shown at the right-hand side of the Driving view. Note: If the speed limit for the road you are on is available, it is shown next to your speed. If you drive faster than the speed limit, your speed is shown in red.

Guided tours

Tap this button to show one of the Guided tours on how to use your TomTom ONE.

Set units

Tap this button to set the type of units that will be shown for the following: Distance
Time Latitude and longitude Temperature Air pressure
Operate left-handed / Operate right-handed
Tap this button to move important buttons, for example, the Done and Cancel buttons as well as the zoom bar, to the left hand side of the screen. This makes it easier to tap the buttons with your left hand without blocking the screen.

Operate lefthanded

To move the buttons back to the right hand side of the screen, tap Operate right-handed.

Keyboard preferences

You use the keyboard to enter your destination or to find an item in a list, such as a POI. Tap this button to select the size of the keys on the keyboard and the keyboard layout. You can select from two sizes: Large keyboard Small keyboard Three keyboard layouts are available: ABCD keyboard QWERTY keyboard AZERTY keyboard Note: The keyboard does not include accents of any kind for any language so you dont have to worry about entering letters with accents. Simply type the letter without the accent and your ONE will recognize the word.

38 min

1. Tap the Traffic sidebar. Tip: If you have trouble tapping the Traffic sidebar and the Main Menu is being displayed instead of the traffic menu, try tapping your finger half on the Traffic sidebar and half off the screen. 2. Tap Minimize traffic delays. Your device looks for the quickest route to your destination. It is possible that the new route may also include traffic delays, or may even be the same route as before. You can re-plan the route to avoid all delays, but this new route will take longer than the quickest route already shown. 3. Tap Done. Tip: It is possible to let your TomTom device automatically minimize traffic delays for you, to do this, see Changing traffic preferences (37).
Changing traffic preferences
Use the Change Traffic preferences button to choose how traffic information works on your device.
To change your traffic preferences, do the following: 1. Tap the TomTomTraffic button in the Main Menu on your device.
Change Traffic preferences
2. Tap Change Traffic preferences. You can change the following preferences: Automatically minimize delays after every traffic update - if you select this option, your device automatically recalculates when new delays occur on your route. Beep when traffic situation on route changes - if you select this option your device beeps when a new traffic incident occurs on your current route. Ask for traffic updates when preparing a route - this option has no effect in RDS traffic.
3. Select or clear the check box next to each preference you want to change. 4. Tap Done. Your device lists the countries that have radio stations providing RDSTMC traffic information that you can currently receive. Normally you can leave this set to Any country (strongest signal). For more information about this country setting, see Choosing the correct country for RDSTMC reception (39). 5. Tap Done.
Making commuting to work easier
The Home to work or Work to home buttons in the Traffic menu lets you check your route to and from work with one tap of a button. When you use either of these buttons, your device checks the route for possible delays, and if it finds any, provides you with the possibility to avoid them. The first time you use Home to work, you must set your traffic home and work locations, do the following: 1. Tap the TomTomTraffic button in the Main Menu on your device. 2. Tap Show home-work traffic.

Change homework

3. Tap Change home-work 4. Set your home location 5. Set your work location. You can now use the Home to work and Work to home buttons of the Show home-work traffic menu.
For example, to check for delays on your route home, do the following: 1. Tap the TomTomTraffic button in the Main Menu on your device. 2. Tap Show home-work traffic. 3. Tap Work to home. The route summary screen is shown. To see if there is a quicker way home, you could now tap the Find alternative button and then tap Minimize traffic delays. Tip: You can let your device automatically look for alternative routes by selecting Automatically minimize delays after every traffic update in your Traffic preferences. For more information, see Changing traffic preferences (37).
Note: It is possible that the alternative route could be longer than your original one (even with its delays). If this is the case, you could always try using the Find alternative button again.
Setting the radio frequency for RDS-TMC information
If you know the frequency of a particular radio station you want to use for RDSTMC traffic information, do the following to set the frequency manually: 1. Tap the Traffic sidebar in the Driving View. 2. Tap Tune Manually.

Tune manually

3. Enter the frequency of the radio station. 4. Tap Done. Your TomTom device looks for your radio station. If it doesn't find a radio station at the frequency you set, it automatically continues to search for the next available station.
Choosing the correct country for RDS-TMC reception
If you are driving close to a country border, your device may tune to a radio station from a neigboring country. If this happens you will only receive RDSTMC traffic information for that country. To set the country you want to receive traffic information for, do the following: 1. Tap the Traffic sidebar in the Driving View. 2. Tap Change Traffic preferences. A list of preferences you can choose is shown, these preferences are described in Changing traffic preferences (37). 3. Tap Done. A list of neigboring countries is shown. 4. Tap on the country that you want to receive traffic reports for. Your TomTom device then searches for a radio station in the country you have chosen.

The Traffic sidebar

The Traffic sidebar is shown on the right side of the Driving View when TomTom Traffic is switched on. The Traffic sidebar shows you the traffic incidents on your route. It shows the following information: A symbol for each traffic incident in the order they occur along your planned route. The estimated delay to the next traffic incident on your route. The distance from your current location to the next incident on your route. An example of a Traffic sidebar is shown below.

WHAT THIS WARRANTY DOES NOT COVER
2) The Limited Warranty does not apply to normal wear and tear, does not apply when the Hardware is opened or repaired by someone not authorized by TomTom and does not cover repair or replacement of any Hardware or part thereof damaged by: misuse, moisture, liquids, proximity or exposure to heat and accident, abuse, non-compliance with the instructions supplied with the Hardware, neglect or misapplication. The Limited Warranty does not cover physical damage to the surface of the Hardware. This Limited Warranty does not cover any software that may accompany or be installed on the Hardware. The Limited Warranty does not cover the installation, removal or maintenance of the Hardware or any costs related herewith.
HOW TO MAKE A WARRANTY CLAIM
3) In order to make a claim of a Defect, you must contact TomTom during the Warranty Period at: 1-978-287-9555 or per email via www.tomtom.com to explain the Defect and to obtain an RMA number (Return Materials Authorization) if necessary. You must return the Hardware during the Warranty Period, along with an explanation of the Defect, to the address provided to you by TomTom. If a defect arises and a valid claim under this Limited Warranty is received by TomTom after the first one hundred and eighty (180) days of the Warranty Period, TomTom is entitled to charge you for any reasonable shipping and handling costs made in connection with the repair or replacement of the Hardware. You must comply with any other return procedures stipulated by TomTom, if any.

YOUR LEGAL RIGHTS

4) This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state and jurisdiction to jurisdiction. 5) If any part of this Limited Warranty is held to be invalid or unenforceable, the remainder of the Limited Warranty shall nonetheless remain in full force and effect. 6) This Limited Warranty is the only express warranty made to you and is provided in lieu of any other express warranties or similar obligations (if any) created by any advertising, documentation, packaging, or other communications. 7) Except for the Limited Warranty and to the maximum extent permitted by applicable law, TomTom and its suppliers provide the Hardware "AS IS AND WITH ALL FAULTS", and hereby disclaim all other warranties and conditions, whether express, implied or statutory, including, but not limited to, any (if any) implied warranties, duties or conditions of: merchantability, noninfringement, quiet enjoyment, system integration, satisfactory quality, fitness for a particular purpose, reliability or availability, accuracy or completeness of responses, results, workmanlike effort, lack of viruses, and reasonable care and skill, all with regard to the Hardware, and the provision of or failure to provide support or other services, information, software, and related content through the Hardware or otherwise arising out of the use of the Hardware. This exclusion does not apply to (i) any implied condition as to title and (ii) any implied warranty as to conformity with description. If applicable law requires any implied warranties with respect to the Hardware, all such warranties are limited in duration to ninety (90) days. Some states and/or jurisdictions do not allow limitations on how long an implied warranty lasts, so the above may not apply to you. 8) This Limited Warranty cannot be transferred to any other person.

LIMITATION OF LIABILITY

9) Neither TomTom nor its suppliers shall be liable to you or to any third party for any indirect, incidental, consequential, special or exemplary damages (including in each case, but not limited to, damages for the inability to use the equipment or access data, loss of data, loss of business, loss of profits, business interruption or the like) arising out of the use of or inability to use the Hardware even if TomTom has been advised of the possibility of such damages. 10) Notwithstanding any damages that you might incur for any reason whatsoever (including, without limitation, all damages referenced herein and all direct or general damages in contract or anything else), the entire liability of TomTom and any of its suppliers shall be limited to the amount actually paid by you for the Hardware. 11) Notwithstanding the above, neither party's liability for death or personal injury resulting from its own negligence shall be limited. 12) Some states and/or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

Addendum

Important Safety Notices and Warnings
Global Positioning System The Global Positioning System (GPS) is a satellite-based system that provides location and timing information around the globe. GPS is operated and controlled under the sole responsibility of the Government of the United States of America which is responsible for its availability and accuracy. Any changes in GPS availability and accuracy, or in environmental conditions, may impact the operation of your TomTom device. TomTom does not accept any liability for the availability and accuracy of GPS. Use with Care Use of a TomTom device for navigation still means that you need to drive with due care and attention. Aircraft and Hospitals Use of devices with an antenna is prohibited on most aircraft, in many hospitals and in many other locations. A TomTom device must not be used in these environments. Battery This product uses a Lithium-Polymer battery. Do not use it in a humid, wet and/or corrosive environment. Do not put, store or leave your product in or near a heat source, in a high temperature location, in strong direct sunlight, in a microwave oven or in a pressurized container, and do not expose it to temperatures over 60 C (140 F). Failure to follow these guidelines may cause the Lithium-Polymer battery to leak acid, become hot, explode or ignite and cause injury and/or damage. Do not pierce, open or disassemble the battery. If the battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical attention immediately. For safety reasons, and to prolong the lifetime of the battery, charging will not occur at low (below 0 C/32 F) or high (over 45 C/113 F) temperatures. Temperatures: Standard operation: -10 C (14 F) to +55 C (131 F); short period storage: -20 C (-4 F) to + 60 C (140 F); long period storage: -20 C (-4 F) to +25 C (77 F). THE LITHIUM-POLYMER BATTERY CONTAINED IN THE PRODUCT MUST BE RECYCLED OR DISPOSED OF PROPERLY. USE YOUR TomTom ONLY WITH THE SUPPLIED DC POWER LEAD (CAR CHARGER/BATTERY CABLE) AND AC ADAPTER (HOME CHARGER) FOR BATTERY CHARGING. To recycle your TomTom unit please see your local approved TomTom service center.

SPECIAL NOTE REGARDING DRIVING IN CALIFORNIA AND MINNESOTA California Vehicle Code Section 26708 (a) (1) provides that No persons shall drive any motor vehicle with an object or material placed, displayed, installed, affixed or applied upon the windshield or side or rear windows. Drivers in California should not use a suction mount on their windshield, side or rear windows. Note: this section of the California Vehicle Code applies to anyone driving in California, not just California residents. Minnesota State Legislature Statutes Section 169.71, subdivision 1, section 2 provides that A person shall not drive or operate with any objects suspended between the driver and the windshield other than sun visors and rearview mirrors and electronic toll collection devices. Note: this Minnesota Stature applies to anyone driving in Minnesota, not just Minnesota residents. TomTom Inc. bears no responsibility for any fines, penalties or damage that may be incurred by disregarding this notice. While driving in any state with windshield mounting restrictions, TomTom recommends the use of the supplied Adhesive Mounting Disk or its Alternative Mounting Kit, which includes multiple options for mounting TomTom devices on the dashboard and using the air vents. See www.tomtom.com for more information about this mounting option.
FCC Information for the User
This product contains a transmitter which must not be co-located or simultaneously operated in conjunction with any other transmitter. Exposure to Radio Frequency Radiation This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Radio and Television Interference This equipment radiates radio frequency energy and if not used properly - that is, in strict accordance with the instructions in this manual - may cause interference to radio communications and television reception. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation distance between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Data Source Tele Atlas North America. Inc. All rights reserved. Canadian data DMTI Spatial. Portions of Canadian map data are reproduced under license from Her Majesty the Queen in Right of Canada with permission from Natural Resource Canada. Point of Interest data by Info USA. Copyright 2007.
Some images are taken from NASAs Earth Observatory. The purpose of NASAs Earth Observatory is to provide a freely-accessible publication on the Internet where the public can obtain new satellite imagery and scientific information about our home planet. The focus is on Earths climate and environmental change: earthobservatory.nasa.gov/