FITTING INSTRUCTION

Clamp mark in acc. with ISO PN 1 L 2 + 4 R 5 58R 7 58L Cables joining Left directional lights Rear fog lights Ground Right directional lights Right side parking lights Stoplights Left side parking lights
The instruction of the assembly
1. Disassemble the rear bumper. 2. Detach reinforcement of the bumper. From reinforcement detach fasteners (not used any more) and detach small fasteners on the left side see figure 2.

Fig. 2

detach

5 detach

3. In the lower part of the bumper cut out fragment according to figure 3. 4. Put main bar of the towbar (pos. 1) into chassis members this way, so holes in main bar agree with holes in chassis members and fix it by bolts M10x40mm (pos. 5). 5. Reinforcement of the bumper fix to the towbar using bolts M8x25mm (pos. 7). 6. Fix the bumper together with polystyrene of the fulfillment.

Fig. 3 Fig. 1 cut out

This towbar is designed to assembly in following car: KIA CERATO, catalogue no. T47, produced since 2004 till 2008 and is prepared to tow trailers max total weight 1450 kg and max vertical load 56 kg.

From manufacturer

Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and correct exploitation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install in points described by a car producer.
7. Screw tow-ball (pos. 2) and socket plate (pos. 3) using bolts M12x75mm (pos. 4) from accessories. 8. Tighten all bolts according to the torque shown in the table. 9. Connect electric wires of 7-poles socket according to the instruction of the car. (Recommend to make at authorized service station) 10. Complete paint layer damaged during installation.
Torque settings for nuts and bolts (8,8): M Nm M Nm M Nm M Nm

Towbar accessories:

PPUH AUTO-HAK S.J.
Produkcja Zaczepw Kulowych Henryk & Zbigniew Nejman 76-200 SUPSK ul. Soneczna 16K tel/fax (059) 8-414-414; 8-414-413 E-mail: office@autohak.com.pl www. autohak.com.pl
Towing hitch (without electrical set)

Class: A50-X

Cat. no. T47
Designed for: Manufacturer: KIA Model: CERATO produced since 2004 till 2008
Technical data: D-value: 8,0 kg maximum trailer weight: 1450 kg maximum vertical cup load: 56 kg
Approval number acc. to regulations EKG/ONZ 55.01: E20-55R-01 1813
After install the towbar you should get adequate note in registration book (at authorised service station).The car should be equipped with: Indicators Tow mirrors After 1000km of exploitation check all bolts and nuts. The ball of towbar must be always kept clear and conserve with a grease.

Foreword

This towbar is designed according to rules of safety traffic regulations. The towing hitch is a safety component and can be install only by qualified personnel. Any alteration or conversion of the towing hitch is prohibited and would lead to cancellation of design certification. Remove insulating compound and underseal from vehicle (if present) in the area of the matting surfaces of the towing hitch. The vehicle manufacturers specifications regarding trailer load and max. vertical cup load are decisive for driving, and values for the towing hitch cannot be exceeded. D-value formula: Max trailer weight [kg] x Max vehicle weight [kg] Max vehicle weight [kg] X 9,81 = 1000
Max trailer weight [kg] +

D [kN]

Clearance Sale
The 2010 Kia Cerato Forte and Forte Koup
We are making room for the new 2011 Forte Duo. That's why we are letting our well-loved 2010 Cerato Forte and Forte Koup go at such irresistible prices! Don't miss out on your chance to own an award-winning drive.
Bonus! Get a free bodykit and GPS worth $3,500 when you order your 2010 Cerato Forte or Forte Koup today!
Kia Showrooms 239 Alexandra Road Tel: 22 Ubi Road 4 Fulco Building Tel: 6746 2000
Promotion valid for 2010 Cerato Forte (5-speed manual / 4-speed automatic) only. While stocks last. Other terms and conditions apply.

1.6L / 2.0L