Back Components

Component External GPS Antenna Connector Stylus
Description This connector (under rubber dust cover) allows use of an optional external GPS antenna with magnetic mount, which may be positioned on top of the vehicle for better signal reception in areas with poor reception. Tap the touch screen to make selections and enter information. Pull the stylus out of its slot to use it, and store it in the slot when not in use. Audio output for music, sounds and voice.

Speaker

Right-Side Components
Component Power Button Navigation Button
Description Turns on and off the device. Starts the navigation software. When using the Bluetooth HF Phone function: Hides or displays the Bluetooth HF Phone screen.

Top Components

Component SD/MMC Slot
Description Accepts a SD (Secure Digital) or MMC (Multi Media Card) card for accessing data such as MP3/WMA music.

Bottom Components

Component Reset Button
Description Resets the N.I.C.E. 430. All saved information will be lost Connects to stereo headphones.
Headphone Connector Mini-USB Connector Connects to the vehicle charger or USB cable. Connects to the optional Traffic module (NAVRDS).
1.2 Performing the Initial Start Up
1. For the initial start up, press the power button for 6 seconds to turn on the N.I.C.E. 430.
NOTE: For sleep mode, briefly press the power button to turn on and off the N.I.C.E. 430.
2. Immediately charge the N.I.C.E. 430 upon the initial start up. Please refer to the charging the battery section for assistance. 3. The Switch Language screen appears. Tap the up/down arrow button to select the desired language. Then, tap the button.
4. The Date/Time screen appears. Tap the appropriate arrow button to select button. the time zone, date, and time. Then, tap the
5. Once the Main Menu Screen appears, you can begin using the N.I.C.E. 430. It is recommended to fully charge the battery before use.
1.3 Charging the Battery via the USB Cable
When charging the battery for the very first time, you should charge it for at least 8 hours. 1. Turn ON the computer. 2. Connect the mini-USB end of the USB cable to the bottom of the N.I.C.E. 430 and the other end to a USB port on your computer.
NOTE: If you intend to charge the N.I.C.E. 430 this way, turn OFF your device so that it takes less time to charge the battery. CAUTION: For optimal performance of the lithium battery: Do not charge the battery where the temperature is high (e.g. in direct sunlight). There is no need to fully discharge the battery before charging. You can charge the battery before it is discharged. When storing the product for a long period of time, be sure to fully charge the battery at least once every two weeks. Over discharge of the battery can affect the charging performance.
1.4 Using the N.I.C.E. 430 in a Vehicle

Tap the respective button (incoming missed

, outgoing

) to view the last 20 calls of the selected type.
With an item selected, you can tap delete the item. To clear all items in the current list, tap

to dial the number or.

5.4 Operations during a Call
During a call: If you need to input other numbers, such as an extension number, tap to open the keypad and tap the digits. The keypad will close when you tap the button again or when there has been no input for 5 seconds. Tap to mute your sound so that the other party cannot hear you. To end the mute mode, tap the same button again. Tap to end the call.
Tap to switch the call to your mobile phone. To switch back to your device, tap the same button again. Press the hardware button ( ) to hide the Connected screen. To display the Connected screen again, press the same button.

5.5 Receiving a Call

When you have a call after pairing with a mobile phone, the device rings and displays the Incoming Call screen.
To accept the call, tap To reject the call, tap.
To mute the ring tone before receiving or rejecting, tap
5.6 Miscellaneous Buttons
In addition to buttons for placing a call, there are Connect, Pair Mode, Bluetooth Manager, and Exit buttons on the Bluetooth HF Phone main screen as described below.

Connect

By tapping the Connect button on the Bluetooth HF Phone main screen, you can manually search the last paired mobile phones for an available connection.
By tapping the Pair Mode button on the Bluetooth HF Phone main screen, you can manually set your device to Pair Mode. Within the duration of 60 seconds, you can initiate the pairing process on your mobile phone to discover your device as a hands-free device.
By tapping the Bluetooth Manager button on the Bluetooth HF Phone main screen, you can run the Bluetooth Manager program. (See Chapter 6 for information on Bluetooth Manager.)
To hide the Bluetooth HF Phone screen, tap the Exit button on the Bluetooth HF Phone main screen. Bluetooth HF Phone is still running in the background
NOTE: To know how to turn OFF Bluetooth radio, see section 6.3.

About the Cigarette Lighter Adapter
Do not use the cigarette lighter adapter in a high moisture environment. Never touch the cigarette lighter adapter when your hands or feet are wet. Allow adequate ventilation around the cigarette lighter adapter when using it to operate the device or charge the battery. Do not cover the cigarette lighter adapter with paper or other objects that will reduce cooling. Do not use the cigarette lighter adapter while it is inside a carrying case. Connect the cigarette lighter adapter to a proper power source. The voltage requirements are found on the product case and/or packaging. Do not use the cigarette lighter adapter if the cord becomes damaged. Do not attempt to service the cigarette lighter adapter. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture.

About the Battery

Use a specified charger approved by the manufacturer.
CAUTION: This unit contains a non-replaceable internal Lithium Ion battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, puncture, or dispose of in fire or water.
Important instructions (for service personnel only) Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Replace only with the same or equivalent type recommended by the manufacturer. The battery must be recycled or disposed of properly. Use the battery only in the specified equipment.

Owners manual

Navigation

Copyright note

The product and the information contained herein may be changed at any time without prior notification. This manual nor any parts thereof may not be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of Clarion Co., Ltd. Whereis map data is 2006 Telstra Corporation Limited and its licensors Data Source 2006 Tele Atlas N.V.
Austria: Denmark: France: Great Britain: Italy: Northern Ireland: Norway: Switzerland: The Netherlands: BEV, GZ 1368/2003 DAV IGN France Ordnance Survey data with permission of Her Majestys Stationery Office Crown Copyright Geonext/DeAgostini Ordnance Survey of Northern Ireland Norwegian Mapping Authority, Public Roads Administration / Mapsolutions Swisstopo Topografische ondergrond Copyright dienst voor het kadaster en de openbare registers, Apeldorn

Note: The colors mentioned and screenshots included in this manual refer to the default daytime and night color schemes. They may not look the same in the schemes you have chosen. Tip: If you use N.I.C.E 430 after sunrise or before sunset, look for the sun in the sky in the map background using a flat 3D view. It is displayed at its actual position to give you another way to orientate, and also to provide some eye candy.

4.3.4 Streets and roads

The similarity of N.I.C.E 430 to paper roadmaps is also convenient when it comes to streets, the most important elements of the map concerning navigation. N.I.C.E 430 uses similar color codes to those you are accustomed to, and the width of the streets also refers to their importance, so it will not be difficult to tell a highway from a small street. Streets and roads have names or numbers for identification. Of course, this information can be displayed on the map. N.I.C.E 430 uses two different ways to show street labels. The conventional way is the same as a roadmap it displays the name of the street aligned with the street. The alternative is a kind of virtual signpost stuck into the street itself.
You need not choose between the two modes. N.I.C.E 430 will use the one best for the current tilt and zoom level. Zoom in to have only a few streets on the map, and start tilting up and down to see how N.I.C.E 430 switches between the two modes in an instant. Note: The automatic switching is on even when using Smart Zoom. At first you may find it odd, but later you will discover how it adjusts the displayed information to the current view of the map. It is important, as the driver must be able to read the map at a glance.
Tip: If you do not want to be bothered by street names during navigation, turn them off in Map Options (Page 66). Tip: Major roads usually have alternative names (numbering) besides the primary name. You can choose whether to display these alternative names or not. You can set this in Map Options (Page 66).

4.3.5 Other objects

Note: When your GPS position is available, and Lock-to-Position (Page 32) is active, the cursor is the current GPS position, the blue arrow. When you select another point by tapping the map, or using the Main menu (Using the Main menu), the new Cursor is shown on the display with the red dot and the radiating red circles.
4.3.8 Marked map points (Pin)
The Cursor can be marked with a Pin. Pins are shown as being stuck in the map. A Pin is visible at all zoom levels and remains in its position until you unpin it, or delete all Pins in Advanced settings (Page 78). The color of the Pin is automatically selected by N.I.C.E 430. Different colors help you identify a Pin in the History list (Page 86) later. There they are shown together with their address and GPS Coordinates. Tip: A quick way to tell the coordinates of a location you found on the map is to Pin it, and then look for the coordinates in the History list (Page 86).This way you also save
the coordinates with the Pin for later reference. If you do not need the coordinates later, just select the point and start Find Coordinates (Page 86).
4.3.9 Visible POIs (Points of Interest)
N.I.C.E 430 comes with thousands of built-in POIs, and you can create your own POI database as well. Having all of them displayed on the map would make the map too crowded. To avoid this, N.I.C.E 430 lets you select which POIs to show and which ones to hide (Page 45) using their categories and subcategories. POIs are represented by icons on the map. For a built-in POI it is the icon of the subcategory of the actual POI. For points you create, it is the icon you had chosen when you created the POI (it can be changed later). These icons are large enough to recognize the symbol, and semi-transparent so as not to cover the streets and junctions behind them.
When the map is zoomed out, the icons are not shown. As you zoom in, small dots appear at the locations of visible POIs. Zooming in further makes the full icons appear.
is If two points are too close to each other so that icons overlap, a multi-POI icon shown instead of individual ones. Zoom in more to see them separately. (Should the two POIs have the same icon, this icon will be displayed instead of the multi-POI icon.)
Note: When navigating, POI icons can be disabled together with street names (Page 66). If you still need this information during your journey, just drag the map to disable Lock-to-Position (Page 32). This will restore street names and POI icons immediately. Now tap Lock to reactivate Lock-to-Position. Tip: Tap the map on or near a POI item to see the list of the names of the nearest POIs in a popup list, if it is enabled (Page 47). To see the details of a particular POI in the list, tap the blue i icon on the right. If you have too may POIs nearby, this list may not be complete. In the Cursor menu (Page 35) there is a button called POI that leads you to the screen of all nearby POI items. There you can open them one by one to see their details, and select any of them as a route point.

4.3.10

Road safety cameras
Road safety cameras, such as speed cameras and red light cameras are special POI types in N.I.C.E 430. They are described in detail here: Page 57.

4.3.11

Elements of the Active Route
N.I.C.E 430 uses a multi-destination routing system in which you have a start point (your current location if GPS position is available), a destination, the line of the active leg of the route, and optionally via points and inactive legs. They are all shown on the map. 4.3.11.1 The start point, via points and the destination
These points are represented by flags.

4.3.11.2

Animated turn guidance
Animated arrows represent all route events other than the above-mentioned special points. These arrows show the direction in which you need to continue your journey.

4.3.11.3

The active leg of the route
The active leg is the section of the route you are currently driving. If you have not added any Via points, the whole route will be the active leg. When Via points are present, the active leg is the part leading from your location to the next via point. The active section is displayed in green/red. It is always the most conspicuous part of the map even when in the background of a 3D map view.
The line of the route is displayed on the driving side of the road for two-way and on the axis in case of one-way streets. When the map is zoomed in and the line is wide enough, small arrows show the direction of the route. This can be useful if you preview the route before starting the journey or when entering a complex junction.

4.3.11.4

Inactive legs of the route
Future sections of a route are inactive. They are also shown on the map with the same color but a darker tint than the active one. An inactive route section becomes active as soon as you reach its starting Via point.

4.3.11.5

Roads in the route excluded by your preferences
Although you can choose whether to include or avoid some road types in Route parameter settings (Page 69), sometimes they are impossible to avoid near the starting point, via points or the destination. If so, N.I.C.E 430 will display those segments of the route with an alternate color.

4.4 GPS Data screen

Tap the GPS button at the list of TMC messages screen to open this window. The GPS Data screen is a collection of information received from the GPS device and it also serves as the entry point to the following screens: Time Sync.

4.4.1 GPS data displayed

The virtual sky on the left represents the currently visible part of the sky above you, with your position as the center. The satellites are shown at their current positions. The GPS receives data from both the green and gray satellites. Signals from the gray satellites are only received, while green ones are used by the GPS to calculate your current location. On the right you can see the satellite signal strength bars. Grey bars are for the gray and black bars are for the green satellites. To identify satellites use their numbers also shown in the virtual sky. The more satellites your GPS tracks (the green ones), the better your calculated position will be. Additional pieces of information on this screen are: current position in latitude/longitude format, elevation, speed, date, time and calculated accuracy. Note: Accuracy can be affected by several factors the GPS cannot take into account. Use this accuracy information only as estimation. There are two icons on the left to show the status of the GPS connection and the quality of reception.
4.4.2 GPS connection indicator
In the middle to the left there is a lamp similar to the ones used for switches. This one has more colors and represents more values: a fast blinking green lamp means that there is communication with the GPS and data is being received, other colors may not appear with a built-in GPS. Should any of these appear, this means a faulty operation of your device.
4.4.3 GPS data quality indicator
In the top left corner there is a satellite dish to show the quality of the GPS position. Different colors represent different signal quality: black with a red cross means there is no connection with the GPS device. This should never be the case if your device has a built-in GPS. red means the GPS is connected but no GPS position is available, yellow means 2D reception. A GPS position has been acquired, N.I.C.E 430 is ready for navigation, but the GPS is using enough satellites for calculating the horizontal position only. Elevation data is not provided, and the position error may be significant. green means 3D reception. The GPS receiver has enough satellites to calculate altitude. Position is generally correct (yet it can still be inaccurate due to different environmental factors). N.I.C.E 430 is ready for navigation.

4.5.4 Follow mode - lock to GPS position and heading (No. 6)
This semi-transparent icon is displayed if GPS position is available, and the map has been moved. It also appears when you scale or tilt the map while Smart Zoom is enabled. This semi-transparent icon is displayed if GPS position is available, and the map has been moved or rotated. It also appears when you scale or tilt the map while Smart Zoom is enabled.
Normally N.I.C.E 430 positions the map to keep the GPS position visible somewhere on the map (when North-up orientation is selected), or always at the bottom center of the map (when Track-up orientation is selected). If you manually move the map, it will freeze the map in the new position. To return to the GPS position, use this Follow button. When Smart Zoom is enabled, scaling or tilting the map also stops the automatic zooming or automatic tilting respectively. To reactivate Smart Zoom, tap this button. Tip: In Advanced settings you can set a delay time after which N.I.C.E 430 pushes the Follow button for you on the Cockpit screen automatically (Page 75). This can be turned on for re-enabling both Lock-to-Position and Smart Zoom.

4.5.5 Cursor (No. 7)

As described earlier (Page 22), if you tap the map somewhere or select one specific item in Find, it will become the selected point on the map, marked with a small red dot and radiating red circles to make it conspicuous. You can use this point as starting point, via point or destination for your route, you can search for a POI near it, mark it with a pin, or save it as a POI. Note: When GPS position is available, the Follow button will appear indicating that you have disabled Lock-to-Position. Tapping the Follow button will re-enable the position lock and move the cursor back to the current GPS position. The same happens when N.I.C.E 430 restores Lock-to-Position automatically on the Cockpit screen, if it is set in Advanced settings (Page 75).

4.5.6 Map scale (No. 8)

The scale indicator is only available on the Map screen. In 2D map view it represents the scale of the map. In 3D view it is the scale of the nearest part of the map only.
You can use it in both 2D and 3D modes to scale the map. Drag and pull it right to zoom in, or left to zoom out.

4.5.7 Menu (No. 9)

This button opens the Menu with the Find engine, the Quick menu, the Route menu and the exit button that takes you to the Main menu screen. The Menu will be described in detail later: Page 43.
4.5.8 Map orientation and Overview (No. 10)
You can view the map screens in three different presentation modes. This switch will cycle through them in the following order. The usual map orientation for navigation is Track-up. It means N.I.C.E 430 rotates the map during navigation to always face the direction of your travel. In this mode an arrow (compass) points towards North.

5.6.2 Backlight settings

Here you can set how the display backlight behaves when using N.I.C.E 430. These settings are independent of the settings of the other applications of N.I.C.E. 430.
5.6.2.1 Power management At the top of the screen you can set how the backlight will behave when the screen has not been touched for a while. 73
Backlight always on You can choose to have the lights always on. Smart powersave You can also initiate this special feature of N.I.C.E 430. When running on battery Smart Powersave will light up the screen only when you press or tap a button, or if N.I.C.E 430 has something to show you. After a few seconds the light level decreases, and after another few seconds the backlight turns off. This helps you achieve a longer battery life.

5.6.3 Smart Zoom

Smart zoom is a lot more than just a usual automatic zoom. While navigating a route: when approaching a turn, it will zoom in and raise the view angle to let you easily recognize your maneuver at the next junction. If the next turn is at a distance, it will zoom out and lower the view angle to be flat in order to let you see the road in front of you, or it can even switch to an Overview mode to let you follow your position on the map. While cruising: if there is no active route and you are just driving, Smart Zoom will zoom in if you drive slowly and zoom out to the limit set here when you drive at high speed. These automatic features can be set up on this screen.
5.6.3.1 Smart Zoom settings You can set how close Smart Zoom can zoom in when approaching the next turn (Zoom-in limit), and the maximum zoom level to zoom out when the next turn is further away (Zoom-out limit). The default values are set to be optimal in most cases. 5.6.3.2 Enable Overview mode You can configure how the Overview mode is triggered when the next turn is at a distance. The Route event distance will determine when N.I.C.E 430 switches to the Overview or back to the Navigation view.
The Overview zoom level will determine the fixed zoom level of the map in both automatic and manually selected (by the Map orientation icon see here: Page 33) Overview modes. You can change the zoom level manually at any time (the Follow button will not be displayed), but when you enter the Overview mode again, the zoom level will be reset to this value. You can also move the map in Overview mode. Then the Follow button will appear, and when pushed, it will move the map to have your current position in the middle again. Note: when this automatic feature is disabled, you can still enable the Overview mode manually as described here: Page 33. 5.6.3.3 Restore Lock-to-Position and Smart Zoom As described at the hardware buttons and the map screen functions, you can move, rotate, tilt and zoom the map during navigation. In these cases a Lock icon (Page 32) appears on the screen. As already mentioned, you can move, tilt and zoom the map during navigation. In these cases a Lock icon (Page 32) appears on the screen. When you tilt or zoom the map, that part of Smart Zoom is automatically deactivated, the map will still follow your position, but will not change the view parameter you have modified. You can return to the full Smart Zoom mode by tapping the Follow button. If you move the map, all parts of Smart Zoom become deactivated, and the view freezes. Tapping the Follow button makes N.I.C.E 430 follow your position again (Lock-to-Position) and also re-enables Smart Zoom. You can make N.I.C.E 430 push the Follow button for you automatically after a few seconds of inactivity. This functionality and the related parameters below apply to the Cockpit screen only. The Map screen will wait for your action. Restore Lock-to-Position Turn this switch on if you want N.I.C.E 430 to return to your current GPS position after you have moved the map during navigation. This is useful if you have moved the map accidentally, or if you have moved it to quickly check something near your route. After a certain timeout set below, the Follow button disappears, and the map immediately jumps back to show your current position. Restore Smart Zoom

You enter the module at Level 3. From this point you can go forward (down) to give the name of the street, then the house number or intersection, or backward (up) to change the city or country to search. 6.3.1.1 Selecting the city and country to search in The first screen of the address-search module is the list of recently used cities. During normal navigation the first line of the list is always the settlement you are in or near to. Without valid GPS position, or if the Follow button appears, the first line is the settlement the Cursor is in or near to.
Should the settlement you are looking for appear on the list, just tap it and you will immediately jump to the Street Name Input screen with the selected city name or postcode shown at the top of the screen. If the desired settlement is not displayed, use the arrows in the bottom right corner to see more of this list. Tip: If during navigation you need to know the name of the city or the country you are currently in, just start Find/Address and read the first line of the list. This function leads to a reliable result only if GPS position is available, and you have not disabled Lock-to-Position by moving the map. If you find that the list of recently used cities contains settlements you will not visit in the near future, you can choose to empty the list by the Clear button in the bottom left corner. Selecting a new settlement to search in If you are looking for a city or town you cannot find on the list, tap Other City in the top right corner. This will take you to the city name or postcode input screen, where you can select the desired city by entering a few letters of its name or some digits of its postcode, then select from the list of results automatically given by the program if the matching items can be displayed on one page, or displayed on more pages if you tap Done after entering some letters. Note: Only available letters are active on the keyboard when entering the first word of the searched settlement name. All other letters are inactive and gray. Note: Postcodes may not be available for the selected country. In this case you need to enter the name of the settlement.
You can accomplish this by using an alphabetic input screen (either an ABC- or a QWERTY-type). You only need to enter the first few letters, as the program only searches among the settlements that exist in the given country. If the name of the settlement is of more than one word, the searched pattern can be any or the combination of those. You can search for multiple partial words by inserting space characters in the pattern.

For example Key West in Florida will be found if you enter Ke W or even We K (any word order will do). You do not need to enter accents when searching for a destination. Type only the base letters (the letter most similar to the accented one) and N.I.C.E 430 will search for all their combinations in the database (e.g. for the Canadien town Dlage you only need to type Deleage, and the rest is done by the program). As you start typing, N.I.C.E 430 will calculate the number of settlements matching your pattern(s). This number is shown at the right end of the input line. If all the matching city names can fit on one screen, the sound played when hitting the key will be different, and N.I.C.E 430 will show you all the results in a list. You can select the one you are looking for by tapping the appropriate list item. Note: When more than 300 matching items (a list of more than 60 pages) exist for the entered pattern(s), N.I.C.E 430 stops searching, and displays >300 at the right end of the input line. Enter more letters to narrow the list. Note: When the name of the settlement contains a character that is not available on the keyboard (e.g. apostrophe or dash), N.I.C.E 430 considers it a space that splits the word. That is why you can search for Alleyn-Et-Cawood with all the following search criteria: A E C, Et A, or Al Ca. Tip: If you have finished entering the street name and the matching names are still on more than one page, just tap Done, and select your desired settlement from the list. Turn the pages with the arrow buttons in the bottom right corner. Tip: In case you are looking for a city name that has more than one word, you can reduce the list of matches faster if you enter a few letters from each word.
Note: If any of the settlements listed has named suburbs or numbered districts that also appear separately in the map, a Show districts button will appear in the bottom left corner. Tap this button to list the suburbs together with the main settlements. Now the button turns to Hide districts, and tapping it will return to the original, shorter result list.

Creating a multi-point route I have tapped the Route To button once for each destination but only the last one appears in the list, all previous points have disappeared. The Route To button is for starting a new route only. For a single route you tap this when the destination is selected. Multi-point routes can be created after you have established a single route. Add points to the single route by using the Add Via and Add Dest buttons. Applying Route To again will delete the whole route. In your case only single routes existed before, so they were deleted without a warning message. If you already have a multi-point route, N.I.C.E 430 warns you before deleting the whole route. I enabled the speed warning as soon as I bought the product but I have just been fined for speeding because N.I.C.E 430 failed to warn me. For an accurate speed warning the actual speed limits of each street and road must be present correctly on the map. This is a relatively new feature of digital maps, so it may not be available in some countries, and its accuracy still has much room for improvement (ask your Clarion dealer for the details in your region). This feature can help you in several cases but it cannot be considered as serious speed control. That is why it can be turned on and off separately from the reliable voice guidance (Page 63).

8 Glossary

The manual may contain many technical terms. Please look below for an explanation if you are unfamiliar with some of them. 2D/3D GPS reception: The GPS receiver uses satellite signals to calculate its (your) position. Depending on the current positions of the ever moving satellites in the sky, and the objects in your environment, the signal that your GPS device receives may be weaker or stronger. Your GPS needs strong signal from at least four satellites to give a three dimensional position including elevation. If fewer satellites are available, it may still be possible to calculate the position but the accuracy will be lower and the GPS device will not calculate elevation. This is called 2D reception. N.I.C.E 430 shows the quality of reception on the Main menu (Page 16), the GPS Data screen (Page 27) and both map screens (Page 34). Note that 2D and 3D GPS receptions have nothing to do with the 2D and 3D display modes of the map. That is a way of representing the map on the screen independently from the GPS reception. Accuracy: The difference between your real position and the one given by the GPS device is affected by several different factors. The GPS is capable of providing a guess of its current error based on the number of satellites it can receive a signal from, and their position in the sky. This information is shown in N.I.C.E 430 on the GPS Data screen (Page 26). Use it as a general reference only. Note that several other factors affect the real accuracy, some of which the GPS is incapable of estimating (e.g. signal delay in the ionosphere, reflecting objects near the GPS device, etc.). Active route: A route is an itinerary planned to reach your chosen destinations. A route is active when it is used for navigation. N.I.C.E 430 has only one route at a time, and it is always active until you delete it, reach the final destination or exit N.I.C.E 430. When there is more than one destination to reach, the route is cut into different legs (from one via point to another). Only one of these legs can be active at one particular time. The rest of them are unused and shown in a different color on the map. Automatic route planning (Autorouting): You only need to set up your destination, and based on its map, the software will automatically figure out which roads you need to take, and the turns you need to make to get there. N.I.C.E 430 will let you select multiple destinations, and customize some important routing parameters (Page 68). Automatic route recalculation: If this function is enabled (Page 64), N.I.C.E 430 recalculates your route if you deviate from it. When you miss a turn or avoid a roadblock, N.I.C.E 430 waits for a few seconds to be sure you do not follow the route

Chapter 5: SIRIUS Satellite Radio
Music channels include todays hits, R&B oldies, classical music, country, bluegrass, jazz, latin, reggae, rock and more. In season you can listen to 16 NFL games a week, up to 40 NBA games a week, and up to 40 NHL games a week. Coupled with great sports news from ESPN, SIRIUS offers unrivaled sports coverage. News and entertainment offerings include NPR, CNBC, Fox News, Radio Disney and E! Entertainment Radio.
5. SIRIUS Satellite Radio
SIRIUS satellite radio makes available over 120 channels of commercial-free entertainment for your car, home or office. Of those 120 channels, 65 provide original content.
How satellite radio works

Satellite

Over 120 channels of radio content bounce off the network of satellites that encircle the earth.
SIRIUS Satellite Radio company in New York City
To take advantage of SIRIUS satellite radio, you need Clarions NAVSIR SIRIUS Satellite Radio interface and antenna. The interface plugs into the EXT. I/O port on the back of the N.I.C.E. The antenna receives SIRIUS signals anywhere in the continental United States provided no obvious satellite signal obstructions are in the way. Obstructions include: nearby buildings, high terrain, parking garages and tunnels.
The receiver decodes the information and sends it to your N.I.C.E.
Antenna N.I.C.E. NAVSIR interface

Getting started

2. If you are in navigation mode, press SIRIUS again to open the full SIRIUS display.
To listen to SIRIUS satellite radio you need two things in addition to your N.I.C.E.: Optional NAVSIR interface installed in your vehicle. This unit receives the satellite signal. For installation instructions, see the users guide that comes with the NAVSIR. A subscription to SIRIUS satellite radio.

Note your ID number

1. Press the SIRIUS button at the bottom of the screen or press the mode button (toolbox), then press SIRUIS. SIRIUS main screen 3. Press the onscreen MENU button.

N.I.C.E.

4. The unit displays the Menu Options page with the SIRIUS ID option highlighted. 6. The 12-digit SIRIUS ID number appears.
Options menu Options menu 5. Press the SIRIUS ID menu item. 7. Write this number here.
confirms that the antenna is in the best position to receive the satellite signal. 1. 2. Press MENU. The options menu appears.
Activate the radio service
Visit Sirius.com and click JOIN, then follow the onscreen instructions. OR Call SIRIUS at 1-888-539-SIRIUS (7474). A Customer Care representative will activate your service. A subscription fee is involved.
Note Make sure to have your identification number accessible when calling Sirius.

Antenna Aiming

To receive a good signal requires a direct line of sight between you and the satellite. If your reception is poor, moving the antenna may help. This option 3.
Options menu Press the ANTENNA AIMING menu option.
The unit displays two 10-segment horizontal bar graphs with a minus (-) to the left and a plus (+) to the right.
Note In urban areas where structures may affect the line of sight satellite signal, terrestrial repeaters (TER) strengthen the signal. They may not be available in your geographical location.

Basic Operations

1. 2. Antenna aiming graphs The satellite (SAT) graph displays the satellite signal strength. The terrestrial (TER) graph shows the terrestrial signal strength. After activating your SIRIUS subscription, press the SIRIUS button at the bottom of the screen If the unit is in navigation mode, press the SIRIUS button again.
The SIRIUS logo appears for three seconds followed by the SIRIUS default display. 3. Press the onscreen channel previous and next buttons to move to the next channel. The channel starts playing.
Definition A channel is a source of satellite radio content.

Direct tuning by channel

If you know the three-digit channel number: 1. SIRIUS default display For a complete identification of each item on this display, see Sirius Satellite Radio controls on page 17. If youre playing the radio for the first time, the unit displays Updating Channels. 2. Touch the middle of the screen. Enter the channel number using the row of numbered buttons along the bottom of the screen. The unit changes immediately to the channel. If you enter only one or two digits, the unit waits for three seconds before changing the channel.

Tuning by category

Category groups channels by music genre or other content. For example, your favorite rock channels are in the category ROCK. 1. 2. Press the onscreen previous and next category buttons to select a category. Press the displayed channel option to select the channel within the category. The channel begins playing and the LCD returns to the default display.

Previewing by category

This procedure lets you view by category whats currently playing on other channels without changing the current channel. 1. Press the onscreen previous and next category buttons to select a category. The unit displays a list of categories.

Tuning by previewing

There are two ways to preview whats playing before selecting a channel.

Channel list

2. Press DISP (display).
3. Press the channel name on the touch-sensitive screen to select it. The channel begins playing and the LCD returns to the default display. Use channel up and down to scroll among channels.
Touching DISP again and again alternates the list among channel, artist name and song title 3. Press the channel name on the touch-sensitive screen to select it. The channel begins playing and the LCD returns to the default display.

Tuning by favorites

The receiver can locate up to 30 favorite channels 10 per band. This feature saves time by presetting only the channels you like.

Previewing all channels

This procedure lets you view regardless of category whats currently playing on other channels without changing the current channel. 1. Press DISP (display). The unit displays a list of all channels regardless of category. 2. Press DISP again and again to alternate the list among channel, artist name and song title.

Storing favorites

1. Press BAND briefly to select A, B, or C. The Band indicator changes to the corresponding preset band. Each band locates 10 presets. 2. Locate the channel you want to assign to a preset by direct tuning. See Direct tuning by channel on page 80.
3. With the channel playing, press and hold any of the numbered keypad buttons (0-9) for one second. The channel number flashes and remains lit to indicate that the unit stored the channel number. The current channel number replaces any previously stored channel associated with that number.

Press and hold BAND to enter Preset Tune Mode. The Band indicator changes to show the current preset number.

Tuning by preset number

Direct tuning by band and preset
1. Press BAND briefly and again briefly to switch among the three bands: A, B, and C. The Band indicator changes to the corresponding preset band. 2. Press one of the 0 - 9 keys. The associated preset channel begins playing and the LCD returns to the default display.
Press the previous and next channel buttons to move backward and forward through all presets. The associated preset channel begins playing and the LCD returns to the default display.
This procedure displays only stored presets in band and preset number order (A-1, A-2. B-1, B-2. C-1, C-2.). To return to Channel Tune Mode without selecting a preset, press and hold BAND.

Tuning by preset list

1. 2. Press and hold BAND. Press DISP.

Searching for favorites

When you turn N.I.C.E. on, it can automatically search the incoming SIRIUS signal and alert you when a favorite song is playing. Then its up to you to switch from your current channel to the channel playing your favorite.
The unit displays up to five preset channels. 3. 4. 5. Press DISP again and again to alternate among channel name, artist name and song title. Press the onscreen previous and next channel buttons to scroll through the preset list. Press the channel on the touch-sensitive screen to select it. The channel changes and the display indicates that you are in Preset Tune Mode.
Storing favorite information
You may store a list of up to 20 favorite artists and song titles. To store a favorite, it must be currently playing. When a favorite song is playing, press MEMO (memory). The unit makes sure you have not already stored this channel an another preset. Assuming it does not find a duplicate, the unit stores the current program information in its memory and displays a pop-up screen that shows how many of
the 20 memory slots are used and how many are empty.
The unit displays the stored information, one item at a time. Press the onscreen previous and next channel buttons to page through all 20 items.

Finding favorites

If it finds one or more songs playing on channels other than the current channel, the N.I.C.E. beeps and displays Memory Alert for two seconds followed by the list of favorites that are currently playing appears. Press the name of the song on the touch-sensitive screen to select the channel. The stored channel begins to play and the display reverts to its condition before the alert occurred. If you make no selection within 10 seconds, the display returns to its previous status.
Deleting one stored favorite
1. Press and hold MEMO for three seconds. The unit displays the stored information, one item at a time. 2. 3. Briefly press the favorite name. Press Yes or No on the touch-sensitive screen.
Deleting all stored favorites
1. Press MENU. The options menu appears. 2. Press the MEMORY OPTION menu item.
Viewing stored favorite information
1. Press and hold MEMO for three seconds.
The unit displays two options: Automatic Memory Search and Clear All Memory.
Parental control features
You may restrict young people from accessing specific channels in two ways: Skip specific channels when tuning. Use this feature to completely omit specific channels, which the SIRIUS receiver does not even download from the satellite. For instructions, continue with the next topic. Require the listener to enter a four-digit lock code to play specific channels. Use this feature to allow only those who know the four-digit activation code to listen to the channel. For instructions, see Locking out certain channels on page 89.
Memory options To exit without clearing memory, press MENU again. 3. Under Clear All Memory, press Yes.
Press the ADD or SKIP onscreen menu item. Press the onscreen previous and next channel buttons to display the channel selections. Press DISP again and again to alternate among channel name, name of current artist, and name of current song.

Skipping channels

With hundreds of channels available, you may wish to limit the accessible list to only those you like. 1. 2. Press the onscreen MENU button. The options menu appears.

Press the channel number on the touchsensitive screen to skip the channel.

Options menu

The unit displays Skip next to the channel number and will not download this channel during regular tuning.
Accessing skipped channels
There are only two ways to access skipped channels: Enter the channel number directly. See Direct tuning by channel on page 80. Use the Add option to restore the channel.
Restoring a skipped channel
1. 2. 3. Channel list with one channel skipped Pressing the channel number again includes the channel in the download and removes the Skip setting. To return to the menu exit without setting this option, press MENU again. 4. Press the onscreen MENU button. Press the ADD and SKIP onscreen menu item. Press the previous and next channel buttons to highlight the skipped channel. Press the channel number on the touchsensitive screen. SKIP disappears next to the channel number.

The options menu appears

Locking out certain channels
Locking a channel requires the entry of the four-digit lock code to play the channel. You can use this feature to prevent unauthorized people, such as children, from accessing specific channels.

Locking a channel

When you select this option, the unit prompts you to define a four-digit lock code. 1. Press the onscreen MENU button. Options menu 2. Press the LOCK or UNLOCK menu item. The unit displays the lock code entry box.
If this is the first time youve used this feature, enter the default code 0000. If youve used this feature before, enter your unique four-digit code. To change this code, see Changing the lock code on page 92. The unit displays a channel list with the current channel highlighted. 5. Press the channel number on the touchsensitive screen to lock the channel.
Press the onscreen previous and next buttons to highlight the channel to lock.
Channel list with one channel locked The unit displays LOCK next to the channel number. Although the unit will download this channel, it will not allow access during regular tuning without entering the lock code. To exit without setting this option, press Enter or MENU again.
N.I.C.E. Accessing locked channels
To access a locked channel: 1. 2. Enter the direct channel number. Enter the four-digit lock code. The channel begins to play. 3.

Restoring a locked channel
When you select this option: 1. 2. Press the onscreen MEMO button. Press Lock Options on the touch-sensitive screen. The unit displays the lock code entry box.
Note The channel returns to the locked status if you change channels or turn the unit off (for example, turn the vehicle off).
Enter the four-digit code. The unit displays a channel list with the current channel highlighted.
Press the onscreen previous and next channel buttons to highlight the locked channel. Press the channel number on the touchsensitive screen to unlock it. LOCK disappears next to the channel number.

Changing the lock code

The unit displays the lock code entry box.
Press the onscreen MENU button. The options menu appears.
Edit code entry box 3. Options menu 2. Press the EDIT CODE menu item. Enter the four-digit code or 0000 if this is the first time youre setting the code. The New Code prompt appears.
4. Enter the new four-digit code using the keypad buttons. The unit prompts you to confirm the code. 5. Enter the new four-digit code again. You have changed the lock code. To exit without setting this option, press Enter or MENU again. The options menu appears.
Resetting factory defaults
To return the unit to the configuration it had when you purchased it: 1. Press MENU. 2. Options menu Press the FACTORY DEFAULT menu item.

The unit displays:

Restore setting options 3. Press YES. All SIRIUS option settings return to their factory defaults.