Moisturizing shaving system
Rechargeable Cordless Tripleheader Razor

COOL SKIN 8020X

Register your product and get support at

www.philips.com/norelco

ENGLISH 4 ESPAOL 26
Congratulations on your purchase and welcome to Philips Norelco! To fully benefit from the support that Philips Norelco offers, register your product at www.philips.com/norelco
Felicitaciones en su compra y recepcin a Philips Norelco! Beneficiar completamente de la ayuda que las ofertas de Philips Norelco, colocan su producto en www.philips.com/norelco

ENGLISH

IMportant Safety Instructions precautions should When using an electric razor, basic safety
always be followed, including the following: Read all instructions before using this appliance.
DANGER of electric shock: To reduce the risk
1. not reach for a charging stand that has fallen into water. Do Unplug immediately. 2. Charging stand is not for immersion or for use in shower. 3. not place or store a charging stand where it can fall or be Do pulled into a tub or sink. Do not place charging stand in or drop into water or other liquid. 4. Do not use an extension cord with this appliance. 5. Always unplug charging stand from the electrical outlet immediately after using, except when razor is (re)charging. 6. Unplug charging stand before cleaning.
4. Keep the razor and cord away from heated surfaces. 5 Never drop or insert any object into any opening. 6. not charge razor or plug in charging stand outdoors or Do operate where aerosol (spray) products are being used or where oxygen is being administered. 7. not use this razor with a damaged or broken comb, as facial Do injury may occur. 8. Always place razor in stand first, then plug stand into outlet. To disconnect, remove plug from stand from outlet. 9. prevent possible damage to the cord, do not wrap cord To around the charging stand. 10.Never put razor in direct sunlight or store in a pouch at a temperature above 140F. 11.Razor is water-safe and can be rinsed under running tap water or used in shower. Do not submerge razor in water.

SAVE THESE INSTRUCTIONS

IMPORTANT: The power plug contains a transformer. Do not cut off the power plug to replace it with another plug, as this will cause a hazardous condition. CAUTION: Keep shaving conditioner out of reach of children. Do not take internally. Avoid contact with eyes. In case of eye contact, thoroughly flush with cold water. If irritation persists, get medical attention.
WARNINGburns, fire, electric shock, or injury to To reduce the risk of
persons: 1. lose supervision is necessary when this razor is used by, on, C or near children or invalids. 2. Use this razor for its intended household use as described in this manual. Do not use attachments not recommended by Philips Electronics North America Corporation. 3. Never operate this razor if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the razor to the Philips Norelco Service Location for examination and repair.

Table of Contents

60 - DAY MONEY-BACK GUARANTEE Features..8-9. Important.. 10. Introduction..10 Before First Use..10-11 Charging Indications. 11. Charging Razor..11-13. Filling Razor Cartridge.13-14 Recharging.. 14 Put It To The Test & Shaving Tips.14-15. How to Shave With Razor...15-17. Cleaning..17-20. Replacing Cartridges.. 21. Replacing Razor Head Assembly. 22 Maintenance..22-23 Storage.. 23. Assistance.. 24 Accessories.. 24 Warranty... 25. Spanish... 26
To enjoy the closest and most comfortable shave from your new Philips Norelco Mens Razor, the razor should be used exclusively for 3 weeks. This allows your hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after that period of time, you are not fully satisfied with your Philips Norelco Mens Razor, send the product back and well refund you the full purchase price. The razor must be shipped prepaid by insured mail, insurance prepaid, and have the original sales receipt, indicating purchase price and the date of purchase, enclosed. We cannot be responsible for lost mail. The razor must be postmarked no later than 60 days from the date of purchase. Philips Norelco reserves the right to verify the purchase price of the razor and limit refunds not to exceed suggested retail price. Send dated sales receipt, this form with the requested information as indicated below, and the razor, prepaid to: Philips Domestic Appliances and Personal Care Company A Division of Philips Electronics North America Corporation 450 North Medinah Road, Dock 16 Roselle, IL 60172-2329 Please allow 4-6 weeks for delivery of check. (Please Print)

Todays Date___________________________________________________ Name_________________________________________________________ Address________ ________________________________________________ City___________________________________________________________ State_____Zip__________________________________________________ Daytime Telephone No. (____)_____________________________________ Area Code E-mail Address________ ___________________________________________ Model Number _________________________________________________ REASON FOR RETURNING:______________________________________ ______________________________________________________________ ______________________________________________________________ ______________________________________________________________ ______________________________________________________________

Features

Nivea for Men Shaving Conditioner Dispensing System Razor Head Assembly Quick Clean System Individually Floating Heads Shaving Conditioner Release Button LED Charge & Low Battery Indicator Electronic On/Off Button NIVEA FOR MEN Shaving Conditioner Bottle Automatic Worldwide Voltage 100V to 240V AC Rechargeable Cordless - 8-hour full charge for up to 30 minutes of cordless shave time Charging Stand Full 2-Year Warranty 60-Day Money-Back Guarantee
How the Unique Philips Norelco Lift and Cut Shaving System Makes Close Comfortable:
Groove channels beard closer to cutting system

Lifter raises hair

Blade cuts hair which then drops below skin level

Important

Only use the power plug and the charging stand provided to charge the razor. The power plug transforms 100-240 AC volts to less than 24V DC. An adaptor plug may be necessary for cord usage in some foreign countries.Your new razor will automatically convert internally to work on 100V to 240V AC systems.
For hygienic reasons, always replace the shaving conditioner cartridge each time you start using a new bottle of NIVEA FOR MEN shaving conditioner. A new cartridge is supplied with each new shaving conditioner bottle. Use this appliance for its intended household use as described in this manual.

Introduction

The NIVEA FOR MEN conditioner dispensing system applies shaving conditioner directly on your skin for a moisturizing and soothing shave. The formula is enriched with vitamins and chamomile to condition your skin for a healthy look. The Glide Rings on the shaving heads distribute the unique NIVEA FOR MEN shaving conditioner evenly over the skin, offering an even smoother and closer shave, causing less skin irritation and leaving your skin feeling refreshed.

Charging Indications Low Battery Indicator
hen the battery is running low, the light W burns red during shaving. If you switch the razor off when the battery is low, the red light slowly goes off.

Charging Indicator

C During charging, the charging light burns

green.

Before First Use
Charge and fill the razor before you start using it (see Charging & Filling Razor Cartridge sections). Important Only use this razor, power plug, charging stand and HS800 NIVEA FOR MEN shaving conditioner to refill or charge razor.

Charging Razor

Charging or recharging at temperatures below 40F or higher than 95F adversely affects lifetime of batteries. Do not charge razor in a pouch.
Charging and recharging requires a full 8 hours. A fully charged razor has a shaving time of up to 30 minutes. For hygienic reasons, it is advised that you use a new shaving conditioner cartridge on your razor when starting a new shaving conditioner refill bottle. 3
Remove the power plug from outlet as soon as the battery is fully charged.

Filling Razor Cartridge

Only use NIVEA FOR MEN Shaving Conditioner to refill the shaving conditioner cartridge. Any other lotion may cause damage to your razor. Remove the tab of the NIVEA FOR MEN Shaving Conditioner bottle (Model HS800).
Placing or removing razor from charging stand:
lways place razor in stand in an upright A position making sure charging contacts in bottom of stand fit into recess in bottom of razor.

C 1 C 2

Turn the cap on the shaving conditioner bottle clockwise. The cap moves down and the shaving conditioner nozzle appears. Place the nozzle of the conditioner bottle into the opening of the conditioner cartridge on the back of the razor. Move the bottle up and down approximately 5 times to pump the shaving conditioner into the cartridge until you see that the shaving cartridge is full. Do not fill the cartridge beyond the MAX indication.
C Always remove razor from stand by lifting

straight up. Do not tilt razor. o not leave the charging stand with the D razor in it continuously plugged into outlet as it would reduce life of batteries. If storing razor in stand, remove the plug from outlet as soon as the razor is fully charged.
Connect the small plug into the charging stand and put the power plug into any 100V to 240V AC outlet. Use only the cord and charging stand provided. Charging requires a full 8 hours. A fully charged razor has a cordless shaving time of up to 30 minutes.
BE CAREFUL NOT TO OVERFILL SHAVING CARTRIDGE. 5 Remove nozzle of the shaving conditioner bottle from shaving conditioner cartridge
and turn the cap counterclockwise until the nozzle is flush with the top of the cap. Replace the tab on top of the shaving conditioner bottle.
purchase price as long as the request is received within 60 days of purchase.

How To Shave With Razor

Recharging
C This symbol on the razor indicates that the
Recharging requires a full 8 hours.
When razor is fully charged, disconnect the charging plug from outlet. Do not keep charging stand permanently plugged into outlet.
razor can be used in the bath or shower. Make sure the power plug and charging stand do not get wet or near water. Make sure razor is charged and filled with NIVEA FOR MEN shaving conditioner (see Charging & Filling Razor Cartridge sections). Remove Protective Razor Head Cap from razor by sliding it off from the Razor Head Assembly. Wet your face and neck thoroughly with warm water.
Put It To The Test & Shaving Tips
21 Day Trial and Conversion Process. It is a fact that your skin and beard need time to adjust to a new shaving system. se your new razor exclusively for 3 weeks to U fully enjoy the closeness of a Philips Norelco shave. At first you may not get as close a shave as you expect, or your face may even become slightly irritated. This is normal since your beard and skin will need time to adjust. Invest 3 weeks and youll soon experience the full joy of your new razor. tick with it! If you alternate shaving methods S during the adjustment period, it may make it more difficult to adapt to the Philips Norelco shaving system. f you are still not convinced after 21 days, I Philips Norelco will refund you the full
NOTE: This razor can be used similar to a razor blade: you can use the razor on a wet face. 4 Turn razor ON by pressing the on/off button once. Press the shaving conditioner button to apply NIVEA FOR MEN shaving conditioner to your skin. When you release the button, the razor stops dispensing lotion.

The shaving conditioner button only works when the razor is switched ON. If razor does not dispense shaving conditioner, dried shaving conditioner may be blocking the conditioner holes. Thoroughly clean razor (see Cleaning section). Gently move the shaving heads over your skin. Shave against the direction of beard growth using both straight and circular motions. This razor has no hair collection chamber to capture stubble. To prevent stubble from falling, apply sufficient shaving conditioner while shaving. While shaving, press the shaving conditioner button frequently to apply more NIVEA FOR MEN shaving conditioner so that the razor keeps gliding smoothly over your face. The shaving conditioner provides immediate hydrating action and lessens drag or pull against skin. 8 Easy does it. Gently press the razor to your skin so the floating heads can follow the contours of your face. DO NOT press too hard. Too much pressure can pinch the skin into the combs. 6
Make sure shaving conditioner is always released from both holes in the razor head assembly. If not, thoroughly clean razor (see Cleaning section). The razor will not perform optimally when used without shaving conditioner on a wet face. 9 Turn razor off by pressing the on/off button once.
10 Clean razor after EACH use (see Cleaning section). Put the Protective Razor Head Cap on the razor when you store it to prevent the shaving heads from getting damaged. Replace Razor Head Assembly (model HS85) once a year for optimal shaving results. stand. Unplug from the outlet when charging is complete.
12 You may store your razor in the charging

Cleaning

lways clean your razor after each use. A egular cleaning guarantees better shaving R results. ever remove or replace Razor Head N Assembly while motor is on. o not apply pressure to combs. Do not D touch razor heads with hard objects as this
For best shaving results, shaving conditioner should be applied frequently.
may dent or damage precision-made slotted combs. o not use razor if combs are damaged or D broken. Facial injury may occur. ever dry the shaving unit with a towel or N tissue as this may damage razor heads. o not use abrasives, scourers or liquids such D as acetone to clean the appliances.

5 You can store the razor in the charging stand. 6 the Protective Razor Head Cap on Put razor to protect heads.
Razor Head Assembly: After Each Use
It is recommended that you clean the Razor Head Assembly thoroughly after each use to maintain optimal shaving performance. 1 Press the on/off button to turn razor ON. R inse Razor Head Assembly under hot tap water by letting the water run in and around all the openings for at least 30 seconds.
Note: If lotion build-up has occurred, remove Razor Head Assembly and soak for a few minutes under hot water or a degreasing liquid (e.g. alcohol). Be sure to thoroughly rinse Razor Head Assembly under tap water before using razor.
Razor Head Assembly: Once A Month
Do not mix up the cutters and combs as the shaving performance may be adversely affected for several weeks before optimal shaving performance is restored.

C 2 C 3

Turn razor OFF. Remove Razor Head Assembly from razor by pulling Razor Head Assembly straight up from razor.
You can also immerse the Razor Head Assembly in hot water for at least 30 seconds. Make sure the razor is ON to thoroughly remove any residue.
BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS.
Using your thumb and forefinger turn the razor head clockwise and lift the comb off of Razor Head Assembly. Remove and clean one set of cutters and combs at a time.
4 Turn razor OFF and shake off excess water.
Do not clean more than one cutter and comb at a time, since they are all matching sets. If you accidentally interchange the cutters and combs, it could take several weeks before optimal shaving performance is restored. 5 Separate the cutter from the comb and clean with a small brush or rinse clean under hot water. Replace the cutter back onto the Razor Head Assembly making sure the blades are pointing upwards.

Replacing Cartridges

For hygienic reasons, it is recommended to replace the shaving conditioner cartridge each time you start a new shaving conditioner bottle. A new empty cartridge is supplied with each new NIVEA FOR MEN Shaving Conditioner bottle (Model HS800).
Shaving Conditioner Cartridge
Remove the shaving conditioner cartridge from the back of razor.

C 7 C 8

Place the razor head comb back onto the Razor Head Assembly. Be sure to replace the comb back into the original razor head before cleaning the next set. Turn the razor head counterclockwise until it locks into place. Repeat the process for the other two sets of cutters and combs.
Insert the hinge at the top of the new shaving conditioner cartridge into the slot in the rim of the razor back (1). Then press the bottom part of the cartridge with your thumb (2) to attach the cartridge to the razor. You will hear a click. The shaving conditioner cartridge is now ready to be filled (see Filling Razor Cartridge section).

Replace Razor Head Assembly back on razor and push down (you will hear a click). The Razor Head Assembly will only fit correctly in one position on razor. Make sure to align the 2 shaving lotion dispensing holes on the Razor Head Assembly with the 2 shaving lotion tubes on the razor.
Replacing Razor Head Assembly
Replace the entire Razor Head Assembly once a year for optimal shaving results. Replace damaged or worn Razor Head Assembly with model HS85 Philips Norelco razor heads only. razor by pulling the Razor Head Assembly straight up away from the razor.
Note: DO NOT place or clean any parts of the charging stand in a dishwasher.

Storage

he razor can be placed in the charging stand T for safe storage. If storing razor in charging stand, remove the plug from outlet as soon as the razor is fully charged. f appliance will not be used for an extended I period of time, it is recommended that you thoroughly clean Razor Head Assembly before storing. e sure razor is turned off. Remove cord from B outlet and charging stand before storing in a safe, dry location where it will not be crushed, banged, or subject to damage. o not wrap cord around razor or charging D stand when storing. tore cord in a safe location where it will not S be cut or damaged. o not keep charging stand permanently D plugged into outlet. o not place or store charging stand where it D can fall or be pulled into a tub or sink, water or other liquid while plugged in. uring storage, always put the Protective D Razor Head Cap on razor to protect heads.
C 1Remove Razor Head Assembly from the
C 2Place new Razor Head Assembly back on
the razor and push down (you will hear a click). The Razor Head Assembly will only fit correctly in one position on razor. Make sure to align the 2 shaving lotion dispensing holes on the Razor Head Assembly with the 2 shaving lotion tubes on the razor. This razor has no other user-serviceable parts. Any other service should be performed by the Philips Norelco Service Location.

Maintenance

Always remove razor from the charging stand before cleaning appliance. Unplug the charging stand. The stand may be wiped clean using a damp cloth. Water from the tap should be on a warm setting to clean any washable parts.

Assistance

or assistance, call toll free: F
1-800-243-3050 or visit our website: www.philips.com/norelco Information is available 24 hours a day, 7 days a week.

Accessories

Replacement Razor Head Assembly Model HS85 - For maximum razor performance, replace your Philips Norelco Razor Head Assembly once a year. Razor Head Assembly contains 3 cutters & 3 combs. NIVEA FOR MEN Shaving Conditioner and Replacement Razor Cartridge HS800 NIVEA FOR MEN Shaving Conditioner (2.5 fl. oz./75 ml.) and Replacement Razor Cartridge. Philips orelco Razor Accessories may be N purchased at a store near you or on our website www.philips.com/norelco

FULL TWO YEAR WARRANTY Philips Electronics North America Corporation warrants each new Philips Norelco Product, Model 8020X (except cutters and combs) against defects in materials or workmanship for a period of two years from the date of purchase, and agrees to repair or replace any defective product without charge. IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specified voltage.* Use of unauthorized replacement parts will void this warranty. PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE. NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. In order to obtain warranty service, simply ship the product postage prepaid to the Philips Norelco Service Location (information available online at www.philips.com/norelco or at 1-800-243-3050). It is suggested that for your protection you return shipments of product by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this warranty. NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America Corporation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations may not apply to you. * Read enclosed instructions carefully. Manufactured for: Philips Domestic Appliances and Personal Care Company A Division of Philips Electronics North America Corporation LISTED 1600 Summer Street 5th Floor, Stamford, CT 06905-9991

LISTED

This symbol on the products nameplate means it is TM listed by Underwriters Laboratories, Inc. LISTED TM
Norelco, Tripleheader, Lift and Cut, Glide Rings and Electronics North America Corporation.
are Registered Trademarks of Philips
is a Trademark of Philips Electronics North America Corporation. PHILIPS and Cool Skin are Registered Trademarks of Koninklijke Philips Electronics N.V. NIVEA FOR MEN is a Registered Trademark of Beiersdorf AG. Beiersdorf North America Inc. 187 Danbury Road Wilton, CT 06897 www.nivea.com 2007 Philips Electronics North America Corporation. All Rights Reserved.

ENGLISH

HQ 564/563 Philishave Cool Skin

Instructions for use

Opening for shaving emulsion Cool Skin shaving heads Release button shaving unit Pump button Cartridge compartment cover Pilot light ON/OFF button Release button of cartridge compartment

Important

Allow your skin at least two weeks to become accustomed to the Philishave shaving system. Do not press the shaver too hard against the skin while shaving! With this shaving system, you can shave when your skin is either wet or dry. The Nivea for Men shaving emulsion has an immediately moisturising effect on the skin. Remove the cartridge and clean the shaver if you are not going to use the appliance for more than one week. To obtain the best shaving results, it is necessary to follow the instructions in the Cleaning and maintenance section.

Inserting the cartridge

The cartridges with moisturising Nivea for Men shaving emulsion are available in boxes containing five cartridges and one plastic connector. Do not throw the connector away; you will need it for all five cartridges! Use only Philishave Nivea for Men Cool Skin cartridges (HQ 150). Inserting the first cartridge s Take one cartridge from the box. Take the connector (supplied in the same box) out of its bag and push it into the cartridge until it seats with a click.

Shaving

Switch on the shaver by pressing the ON/OFF button. Hold the shaver against the skin.
s Press the yellow pump button to apply Nivea for
Men shaving emulsion to the skin. When sufficient shaving emulsion has been released, start moving the shaving heads rapidly over your skin, making both straight and circular movements. The shaver is suitable for use in the shower.

Introduction

Cool Skin is a new shaving system by Philishave. The shaver has a special compartment for cartridges containing Nivea for Men moisturising shaving emulsion. This emulsion is applied to the skin during shaving. The Nivea for Men shaving emulsion prepares the skin and beard for the shave, ensuring that the shaver moves smoothly over your face and makes perfect contact with the skin. You will enjoy an unexpectedly close and comfortable shave and your skin will feel soft and fresh afterwards. After shaving, you can clean the appliance by simply rinsing it under a hot tap.
Grooming sideburns and moustaches
s Push the release slide downwards and remove the
cover from the cartridge compartment.

Charging the shaver

s Slide the cartridge with inserted connector into the
Trimmer The shaver has a separate trimmer for grooming sideburns and moustaches. Fitting the trimmer onto the shaver Switch off the shaver. Clean the shaver before you assemble the trimmer.
s Press the release button and pull the shaving unit off
Important: only leave the shaver to charge in a dry place! First put the plug in the appliance and then put the Powerplug in the socket. The Powerplug has an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 Volts. The pilot light near the ON/OFF button will go on. It will take the appliance approximately 8 hours to recharge completely. A fully recharged shaver has a shaving time of approximately 30 minutes. The shaver has been equipped with a battery low indication: the pilot light will light up when the battery is running low.

shaver. Replace the cover and close it. Replacing an empty cartridge s Push the release slide downwards and remove the cover from the cartridge compartment. Remove the empty cartridge and pull out the connector. Note: do not throw the connector away!
s Insert the connector into a new cartridge. It has

the shaver.

s Fit the trimmer onto the shaver.
been properly inserted when it seats with a click.
s Slide the new cartridge with the connector into the
Removing the trimmer Press the release button and remove the trimmer.
shaver. Replace the cover and close it.
About the built-in battery
The shaver has been equipped with a built-in rechargeable battery. To prolong the life of the battery, recharge and store the appliance at a temperature between +5C and +35C. Also make sure that you disconnect the shaver from the mains when you are not recharging it. About the cartridge The Nivea for Men shaving emulsion in this cartridge will keep when it is stored at a temperature between 0C and +40C.

Cleaning and maintenance

If you were charging the appliance, pull the Powerplug out of the wall socket and remove the appliance plug from the shaver. Clean the shaving unit with very hot water after every shave. The shaver is fully water resistant and therefore allows easy and quick cleaning. Important: the Powerplug is not waterproof. Prevent it from getting wet and do not immerse it in water! Shaving unit
s Press the release button and flip the shaving unit

Storage

The pouch has been designed to hold the appliance, its dust cover, two spare cartridges and the Powerplug. The pouch is washable; wash it separately (see washing instructions on the inside of the pouch).

Troubleshooting

Shaving heads do not move smoothly over the skin Cause: not enough Nivea for Men shaving emulsion has been applied. s Press the pump button a few times until a sufficient amount of Nivea for Men shaving emulsion has been released to allow the shaving heads to move smoothly over your skin again. Reduced shaving performance Cause 1: the shaving heads are dirty s The shaver has not been cleaned immediately after use and/or has not been rinsed long enough or hot enough. Clean the shaver thoroughly before you continue shaving (see Cleaning and maintenance). Cause 2: long hairs are obstructing the shaving heads Clean the cutters and guards s Remove the retaining plate. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and the guards, it may take several weeks before optimal shaving performance is restored. s Remove the hairs with the brush supplied. Cause 3: shaving heads are damaged or worn Replace the shaving heads s Remove the retaining plate. Remove the old shaving heads from the shaving unit and replace them with new ones. Damaged or worn shaving heads (cutters and guards) must only be replaced by the original Philishave Cool Skin shaving heads (HQ 156)! s Put the retaining plate back onto the shaving unit.

Cover of cartridge compartment cannot be closed Cause 1: the cartridge has not been inserted correctly s Insert the cartridge correctly. The cartridge only fits properly into the shaver in one way. Cause 2: The cartridge has not been pushed far enough into the shaver. s Press the cartridge until it is properly fixed. Shaver does not work when the ON/OFF button is pressed Cause 1: the battery is empty s Recharge the battery. Cause 2: the appliance is connected to the mains.
s Remove the Powerplug from the wall socket and pull

Disposing of the battery

When you discard your shaver in due course, please make sure that the battery is not thrown away with the normal household waste. Remove the battery from the shaver and hand it in at an official collection point. Tip: you may also take or send your Philishave Cool Skin shaver to a Philips Service Centre. There, the battery will be removed and disposed of in an environmentally safe way.
open. If the shaving unit comes detached from the appliance, reattach it by holding it at right angles to the top of the shaver and then reinsert the two projections into the guiding slots.
s Clean the inside of the shaver by rinsing it under a
the appliance plug out of the shaver.

hot tap for some time.

s Rinse the outside of the appliance.
Removing the battery Before you remove the battery, it must be fully discharged. Let the shaver run until it stops.

s Remove the screws.

The Nivea for Men shaving emulsion has lost its colour or has turned watery. Cause: the Nivea for Men shaving emulsion has not been preserved at the right temperature. In case of other problems Please visit the Philips Web site at www.philips.com or consult the Philips Customer Care Centre in your country (you will find its phonenumber in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.
Important: make sure the inside of the shaving unit is really clean. Close the shaving unit again. Shake off excess water. Trimmer Clean the outside of the trimmer with a brush every time you use it. Lubricate the trimmer teeth with a drop of sewing machine oil every six months.
s Flip the trimmer open to clean it on the inside.
s Open the shaver. s Remove the battery.

Beiersdorf, and Nivea for Men are registered trademarks of Beiersdorf AG. All other trademarks are owned by Philips Electronics N.V.

100% recycled paper