XR2/ XR2+

ONE 1 ONE 2 ONE 3 ONE 4 ONE 5 ONE 6 ONE 7 ONE 8 am er A t ck
Intruder alarm system Operating Instructions
These operating instructions cover the following intruder system:
8SP 403 XR2+ G3 panel with built in keypad Unset system indications 8SP 404 XR2 G3 panel with built in keypad

Remote LED keypad

ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 Tamper Attack
For Clarity, the information given on setting the system, assume that all Programs use a timed or final door setting routine.
LED steady On indication LED flashing indication LED Off
o/p ARC Output to Alarm Receiving Centre

Unset system indications

An unset system will have both Day and Power indicators lit. This is a normal Day Power indication when the system is disarmed.

Internal sound

Sound description
NOTE: In general a flat beep is an indication of an incorrect key press. External devices Strobe Bell
Note: If the Power indicator goes off at any time then there is a mains supply failure at the security panel, consult your servicing organisation.

Set System indication

An active Set system will have only the Power Power indicator lit. This is an armed system indication.

issue 1 8/01

www.ukpanels.com

Operating instructions

Contents
Unset system indications Set System indication Access codes How to operate Personal Attack - - - How to unset system in alarm - - - - - Programs 1, 2 and 3 How to set the system (on program 1) - Push to Set Switch Keyswitch Set Faults during setting How to unset the system (turn off) - - How to set program1,2 or 3 - - - - - - How to Quick set - - - - - - - - - - - How to Omit zone(s) on setting system Fire Alarm How to set Chime Zones - - - - - - - Operators Program mode To exit operation at any time How to enter Operators program mode How to view the events log - - - - - - How to create/omit User 2 code - - - - How to change current user code - - - How to carry out Alarm and Walk testsServicing organisation details Quick Reference 8
Citadel XR2/XR2+ G3 Intruder system
How to unset system in alarm
Enter your code. Entering the code will turn the alarm off and the cause of the alarm will be displayed. After investigation press Reset to clear the indication.

n n n n

- - - -
FIRST ZONE IN ALARM OTHER ZONES IN ALARM

Investigate the Alarm

ALL ZONE

Strobe Off

Access codes
Note: If the alarm indication does not clear, then the system may need to be reset by the installation engineer, contact your installer for further information.
Programs 1, 2 and 3 Access codes
There are two User codes used in the system, both are 4 digit and can be set to any number from 0000 to 9999, signified by:
The user 1 and 2 codes have the same operation for testing, Setting and Unsetting, but user 1 code which is usually considered to be the Managers code has the authority to add, change or delete the user 2 code and Duress code.
The panel uses 3 Part Set routines known as Programs. In each Program the exit mode can be changed and the zone may be set up to have a different function. The examples below show how 3 typical Programs could be used in a house. Program 1 To arm all of the zones and become Set as the user leaves the property and closes the final door. Program 2 To protect the perimeter of the property in the evening and become Set after say 20 seconds. Program 3 To protect the downstairs areas of the house at night and become Set silently. The above are purely examples. The installer has the ability at the programming stage to configure all the circuits to the customers exact requirements.
User 1 code 0123 factory set User 2 code not programmed.
How to operate Personal Attack
Personal Attack buttons on the keypad are used to activate the alarm, irrespective of whether the system is armed or not. Press Simultaneously: 9 4
How to set the system (on program 1)
The green Day indicator should be showing. Enter your code number and check Day that the system is clear (none of the n n n n zone indicators 10seconds are showing). The Exit beep insistent beeps sounder will now produce an exit Day beep tone and you should leave by o/p ARC the approved Set output route. The system will Set as the beep tone stops.
How to unset the system (turn off)
On entering the premises an entry beep tone come on. Enter your code, the green Day indicator is lit. The system is unset and disarmed.

Entry beep Day

Acknowledge Day

o/p ARC Unset output

Push to Set Switch
In some systems a Push to Set switch may be fitted outside the premises near to the main exit door. This should be used to complete the setting procedure once the building has been vacated. As the switch is operated, the exit beep tone will How to set program 1,2 or 3 stop and a chime tone will be produced to The green Day indicator should be showing. acknowledge setting. Day Enter your code number and the n n n n exit beep tone will start. Press Exit beep Keyswitch Set the Prog key and ZONE 1-3 Prog Exit beep the exit tone will Your system may have been fitted with a remote keyswitch. This can be used as an alternative to stop. Press 1, Or arming the system with a code and will set or 3 for the Program 1. required 10 seconds Exit beep insistent beeps program, the Where a keyswitch is used it may be necessary sounder will on occasions to allow it to catch up with the Day beep to system. For example if the alarm was set with a o/p ARC acknowledge the code, to Unset with the keyswitch, it would have Set output program number. to be momentarily turned to Set then returned to The exit beep tone will start and you should Unset. leave by the approved route. The system will Set as the beep tone stops.

Faults during setting

If the system is not clear when you try to Set it, the sounder will produce an open zone tone and the fault will be displayed. Either re enter your code to turn off and investigate or omit the faulty zone(s) from the system.
It is important that you follow the correct procedure when setting the system. After leaving the protected area it is absolutely essential that you wait until the exit tone stops, before assuming the system has set.

How to Quick set

During the exit period (on entering User code) Day the system may be Set Set the system or quickly by pressing Set. This removes the exit time Set a Program period.
5 seconds insistent beeps Day

How to set Chime Zones

Example: To set zone 3 and 4 to chime, Press:

o/p ARC Set output

If you omit zones and require Quick Set, you will need to press Set twice.
Timeout after 5 seconds if no selection is made

Day Chime

Deselect all zones (Factory default no chime) Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Appropriate Zone indicator is lit to show chime zone(s)
Zone n Chime selected Zone n Chime deselected
How to Omit zone(s) on setting system
Press number button to select / deselect Zone Chime
During the exit period after entering User code and selecting a Day program press Set the system or OMIT, the exit tone Set a Program and while the will stop and zones system is setting: that are about to be Omit armed will be ZONE(S) TO BE ARMED displayed. Key in Exit beep the zone number(s) to be omitted which Press the zone(s) n to be omitted will flash to confirm selection. Zone ZONE(S) TO BE OMITTED indicators which Set show steady are still about to be armed. 10 seconds Exit beep insistent beeps When the selection Day is complete press o/p ARC Set and the exit tone Set output will start. If a zone refuses to be omitted, it may be because the engineer has programmed the panel to prevent you from turning off the zone. If in doubt ask your installer for advice.

Leave chime mode

Fire Alarm
The fire zone will operate on detection of a fire, whether the system is Set or Unset, when configured as a 24 hour zone, and cause a distinctive internal sounder tone. The external sounders will pulse on and off at 2 second intervals and zone indicator will flash to attract attention.
Chime is a low security monitoring system for use when the system is Unset. When a zone that is set to chime is operated, the internal sounder will produce a low volume two stage warning tone and the Zone indicator will show. The indicator may be cancelled by pressing Reset. Chime is particularly useful in a shop to warn of a customer presence or in a house to warn that a door or particular area has been accessed. Any zone may set to be on or off chime by pressing the CHIME key and then keying in the required zone number(s). Key 0 to cancel all zones from chime. After a few seconds the system will automatically return to the Day mode.

Operators Program mode

The information below shows the programmable options available and how to change them. Once the operator program mode has been accessed, each section may be changed in any order. As each operation is completed the system will automatically return to top level of program mode.

How to view the events log
The panel can hold up to 8 previous events which can be scrolled automatically or manually. The automatic scroll starts with the newest event ( number 8) to the oldest one ( number 1).
Example: To view up to 8 previous events and thereafter to stop the event scroll, Press: Prog Chime
Note: When programming the system should be in the Day mode, with the Day and Power indicators lit.
Enter Operators program mode

View the event log

Tamper
To exit operation at any time
On pressing the Reset key you will quit the current level of operation.
Automatic event scroll Starting from event 1 to 8 To manually scroll View event (oldest event)
Zone, PA and Tamper indicators will be lit to show zone in alarm. Flashing indicates the first zone in alarm. Day indicates status of panel at the time of alarm
Quit the current function Leave Engineering menu Down one menu level
View event 2 View event 3 View event 4 View event 5 View event 6 View event 7
How to enter Operators program mode
To enter the Operators program mode the system should be in Day Prog mode with the Day and ZONE 1 - 8 Power indicator lit. Momentarily On
8 View event 8 (Newest event) Chime Resume automatic scroll

Acknowledge

Stop event scroll / view Leave program mode

Day Acknowledge Tamper

How to create/omit User 2 code
User 1 code which is usually considered to be the Managers Example: To create user 2 code 4567, Press: code has the Prog authority to add, 7 change or delete Reset the user 2 code.
Enter Operators program mode Change / omit User code (By user 1 only)

Attack

How to create/change/omit the Duress code
The Duress code is used in a hold up situation where there is pressure to Set or Unset the system. Entry of the code will allow the system to work normally but also generate a silent PA type alarm by operating the PA communicator output. The duress code in not preprogrammed and can be created.
Example: To createduress 5555, Press:

ZONE 1-4

n New code
NOTE - The sounder will produce a flat beep if code is rejected.
Enter Operators program mode Change / Omit the Duress 9 Code (By user 1 only)

To omit the user 2 code

Rising beeps ZONE 1-4 Attack

Leave program mode

New duress code
How to change current user code
You can change the current user 1 or user 2 code Example: To change user 1 for security code from 0123 to 7777, Press: reason.
Change the code of Current user (either User 1 or User 2)

Current user new code

Rising beeps ZONE 1-4
NOTE - Factory default code for User 2 is not programmed
How to carry out Alarm and Walk tests
The alarm test function allows you to test the Strobe, Bell, Low and High volume sounders of the system. The walk test function allows each detector to be checked in order to verify that they are functioning correctly.
Example: To start bell test and thereafter to stop bell test. Prog 0 Reset Reset Enter Operators program mode

0 Alarm test

Press zero to turn off options 2,3,4 and 5 before selecting a new one

Strobe test

Strobe On Bell on

3 Bell test 6

Low volume sounder High volume sounder Walk test
internal low volume sound internal high volume sound Strobe

Strobe On

x1 for zone 1 x2 for zone 2 | x4 for zone 4 flat x1 for zone 5 flat x2 for zone 6 | flat x4 for zone 8 Rapid for PA Rapid for Tamper
Appropriate zone lights are lit(latched) Zones

Exit current level

Servicing organisation details
Servicing organisation name:
Bell Time: Bell delay Area protected Zone 1 Program 1 Program 2 Program 3

Telephone number:

Date of installation:

Zone 2 Zone 3

Account Number:

Zone 4 Zone 5

Installation Date:
Zone 6 Zone 7 Zone 8 T Timed (Entry/Exit Zone) TI Time Inhibited (Access zone to keypad) I Immediate (All zones armed to give full alarm)

Quick Reference

To Set a Program

Day Entry beep Day Day

To Set the system (Program 1)

n n n n n n n n

To Un-set the system To Quick Set the system Bell

To Reset Alarm state

To Omit zones on Setting system

Exit beep

Exit beep Acknowledge

FIRST ZONE IN ALARM

OTHER ZONES IN ALARM
Set the system or Set a Program

ZONE(S) TO BE ARMED

ZONE 1-3
Set the system or Set a Program and while the system is setting
10seconds insistent beeps
Or Day Day 10 seconds insistent beeps

Exit beep Day

5 seconds insistent beeps

nvestigate the Alarm

o/p ARC Set output o/p ARC Set output
Press the zone(s) to be omitted

ZONE(S) TO BE OMITTED

The panels conform to the requirements of the European EMC and Low Voltage directives, and carries the CE mark.
Operators program mode menu map

Chime Chime

Operators Progam Mode Prog

n n n 7

To exit Operators program mode

To set Chime zone

Alarm test Change / omit User code 2 (By user 1 only) Change the code of Current user (either User 1 or User 2) View the event log

n n n n n

10 seconds insistent beeps Day
Strobe test To omit the user 2 code
Automatic event scroll Starting from event 1 to 8 For manual scroll

Zone to chime

3 Bell test
View event 8 (Newest event)

Low volume sounder

Change / Omit 9 the Duress Code (By user 1 only)

Reset Reset

View event 1 (oldest event)

High volume sounder

Resume automatic scroll
Norma nd cat ons of an Unset system

Day Power

6 n n n
Walk test Press zero to turn off options 2,3,4 and 5 before selecting a new one

A arm nd cat ons

Stop event scroll / view
Quit the current function Leave program menu Down one menu level

Bell On

Strobe Tamper / Serv ce warn ng