Avslutningston (Roger tone)
Du kan aktivera en tonslinga som hrs nr du slpper PTT-knappen. Denna kan anvndas som en uppmaning till den andra personen att du talat frdigt och vntar p svar. 1. Tryck w upprepade gnger tills ro visas. 2. Blddra fram nskad instllning med v/V (OF =av, On=p). 3. Tryck PTT.

Knappljud

Skning av tv kanaler (Dual Watch)
Du kan stlla in en andra kanal fr samtidig avlyssning med den vanliga huvudkanalen. 1. Tryck w upprepade gnger tills DCM visas. 2. Blddra fram nskad kanal med v/V (OF =av). Tryck w. 3. Blddra fram nskad verfringskod med v/V. Tryck w. 4. Tryck PTT.
Declaration of conformity
Doro deklarerar hrmed att produkten Doro BM35 verensstmmer med de vsentliga kraven och vriga relevanta bestmmelser i direktiv 1999/5/EC, 2002/95/EC. Kopia av tillverkardeklarationen finns p www.doro.com/dofc

Felskning

Enheten tnds inte trots att den r pslagen - Batterierna r slut (ladda utrustningen). - r batterierna korrekt isatta? Rundgng - Enheterna r fr nra varandra. Inget ljud i handenheten (frldraenheten) - r samma kanal och verfringskod valda p bda enheterna? - Hj volymen. - Justera nivn fr ljudaktivering (VOX). - Flytta enheterna nrmre varandra (innanfr rckvidden).

Garanti

Denna apparat har ett rs normal varugaranti. Vid eventuell reklamation, tag kontakt med inkpsstllet. Garantiservice utfrs endast mot uppvisande av giltigt inkpskvitto/ fakturakopia. Garantitagandet gller inte om felet beror p olyckshndelse eller liknande, alternativt verkan, intrngande vtska, vanvrd, onormalt brukande, felaktiga batterier, dlig sktsel eller ngot annat missfrhllande p anvndarens sida. Garantin gller inte heller fr fel som uppsttt p grund av ska eller andra elektriska spnningsvariationer.

Location and Use

The Baby Monitor is intended for indoor use to monitor a baby from a nearby location. Please remember that a monitor is no substitute for supervision always ensure you can reach your baby within a few seconds should the need arise. The Baby Monitor only transmits sounds to the parent unit when sounds that exceed the preset level, such as the baby crying, are heard close to the baby unit. (see below). Place the baby unit near to and with the front facing the child. Ensure that the baby unit is out of the childs reach; never place the baby unit in the cot or pram! To avoid acoustic feedback do not place the baby and parent units too close to each other. Advanced versions, e.g. +1, have multiple parent units/handsets and can be used as walkie talkies (PMR) as well, or to monitor two children simultaneously, see the instructions that begin on Page 5.

Connection

Parent Unit ( ) 1. Remove the battery cover as illustrated and insert the battery with plus/minus as shown. 2. Connect the parent units mains adapter to F and the mains wall socket. 3. Press down 1 until a tone is heard and the parent unit is activated. 4. Charge until the battery indicator stop signalling. 5. Unplug the mains adapter and the parent unit is ready for use.

English Baby Unit ( ) 1. Connect the baby units mains adapter to the mains wall socket. 2. Set the control on the units right side in position 1. 3. Adjust sensitivity using the control on the back (A=least sensitive.H=most sensitive) by talking quietly into the baby unit at the same time as someone else listens to the parent unit.

Please note!

The parent unit must be charged for 24 hours before it is used for the first time. The recharging system used in this model may result in it becoming warm. This is normal and will not damage the equipment. Do not place the baby or parent units close to other electrical equipment such as computers, computer screens, telecom equipment, fans, etc. This is to minimize the risk of any interference. Do not place the units in places where they will be exposed to direct sunlight or other major heat sources! Only use original batteries in the parent unit. The guarantee does not cover any damage caused by incorrect batteries.

Battery Information

The symbol | in the display indicates when it is time to recharge the battery. When the battery is running low, the indicator will flash. On the parent unit the sections are turned off one by one as the power goes down. Fully-charged batteries (14 hours charging) will last for approx. 48 hours of normal use or approx. 2 hours of continuous transmission. These operation times apply at normal room temperature. Because batteries only have a certain lifespan it is quite normal that operating time will decrease somewhat compared to the specifications when the baby monitor is used regularly.

Channels

The baby monitor has eight channels each with 38 sub channels. This gives a total of 304 different channel combinations. The parent unit and baby unit must be tuned to the same channel and sub channel in order to work. As transmission is open there is a risk of interception and we recommend that sub channel 0 is NOT selected as this will allow communication from all 38 sub channels. Other electronic equipment can interfere with transmission. If interception or interference does occur, change the channels on both the units or select another sub channel. Parent Unit 1. Press w. The relevant channel flashes (large number). 2. Scroll to the desired channel using v/V. 3. Press w. The relevant sub channel flashes (little number in upper right corner). 4. Scroll to the desired setting using v/V. 5. Wait a few seconds until the display returns to standby mode.

1. 2. 3. 4. 5.

Baby Unit Press MENU. CH is shown on the display. Scroll to the desired channel using v/V. Press MENU. Ct is shown in the display. Scroll to the desired sub channel using v/V. Wait a few seconds until the display returns to standby mode.
In ideal conditions (no obstacles between the units) the range can reach up to 3 km. Volume Control (Parent Unit) On standby the volume can be adjusted using v/V.

Belt clip (Parent Unit)

The equipment includes a belt clip which is fitted to the back of the handset. The belt clip enables the handset to be attached to a belt, waistband or similar. You can remove the clip by lifting the small tab and pushing the clip upwards.

Key Beep (Parent Unit)

The sound heard when you press the buttons can be switched on or off here. 1. Press w repeatedly until to is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Press PTT.
Channel Lock (Parent Unit)
This function locks the channels and the volume on the parent unit to prevent unintentional usage of some buttons ( w and v/V). 1. Press N until the display shows the key symbol. 2. Cancel the key lock by holding N pressed until the symbol in the display disappears.
Turning the Parent Unit On/Off
Press and hold the 1 button for a few seconds to turn the parent unit on or off.
Sound activation / adjustable sensitivity (VOX) Baby Unit
By using the VOX sensitivity adjustment you are able to select the level of sound transmitted from the baby unit to the parent unit. This is useful to filter normal or quite sounds in the room but still hear important or crying noises to suit your preference. Test different settings for sensitivity for the most effective use: A = Least Sensitive H = Most Sensitive.
Safety Signal (Baby Unit)
Using this function, a beep is sent every 30 seconds (in standby) from the baby monitor so that you know that the right channel/sub channel has been set and that the range has not been exceeded. The display shows Beep when the function is active. 1. Press MENU repeatedly until Beep is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Wait a few seconds until the display returns to standby mode.
Automatic Monitoring (Baby Unit)
You can activate a function that monitors for five seconds every five minutes. The display shows Auto Mon when the function is active. 1. Press MENU repeatedly until Auto Mon is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Wait a few seconds until the display returns to standby mode.

Activity Signal (Baby Unit)
The activity signal is an additional aid to get your attention when sounds are heard in the vicinity of the baby unit. This function sends a tone sequence to the parent unit when the baby unit is activated (ie. by the baby crying). The display shows when the function is activated. 1. Press MENU repeatedly until Ca and are shown. 2. Scroll to the desired setting using v/V (OF =off, On=on).
Turning the Baby Unit On/Off
Use the control on the right side of the baby unit to turn it on/off.
Versions with Multiple Parent Units (+1, +2 etc.)
With two or more parent units (referred to as handsets below) this product can be used as a walkie talkie as well. The following description explains how two handsets can communicate with each other. It is also possible to use one of the handsets as a baby unit which means that more than one child can be monitored at the same time, see Page 7.

To communicate

1. Make sure that you use the same channel and sub channel, see Page 3. 2. Press and hold PTT (Push To Talk) while you speak. 3. If nobody answers, send a ring signal by pressing.

Please note! Paging

If the handsets are unable to communicate it may be because you are using different channels or sub channels, the battery is running low or the handsets are too far apart. You can scan all channels to locate one that is transmitting. If a signal is found, the display shows the channel number and the signal is heard for a few seconds. Press PTT to stop at the right channel. During searching, battery power consumption is significantly higher than normal. 1. Press w and v at the same time. The display starts searching among the channels. 2. Disconnect the function by pressing w.

Monitor function

If the signal is weak, the monitor function can be used. 1. Press for at least five seconds. 2. Disconnect the function by pressing PTT.

Sound Activation (VOX)

This unit can be used without having to press the PTT button to transmit. By setting the correct level, the equipment can determine in an instant whether you are speaking or if the sound level in the room is normal. Test different settings for sensitivity. Even with a very accurate setting, there is unfortunately always a slight risk that noise from the surroundings may activate the transmitter, or that the first word wont be heard completely. The latter problem can be solved by calling out the name before every message. The transmitting function is shut off two seconds after you have finished speaking. The display shows VOX when the function is active. If the handset transmits by itself, i.e. it is set too sensitively, press w to be able to interrupt temporarily to change the setting. 1. Press w repeatedly until VOX is displayed. 2. Scroll to the desired setting using v/V. (OF =off, 1=least sensitive.3=most sensitive). 3. Press PTT.

Handset as Baby Unit (to monitor two children)
Versions that have more than one handset can be used to monitor more than one child. For this purpose, one of the handsets is used as a baby unit. 1. Turn down the volume to the minimum using V on the handset that is being used as the baby unit. 2. Set sound activation (VOX) as above on the handset being used as a baby unit.
Make sure that you use the same channel and sub channels on all units.

Call melody

The call melody sent from the handset can be set at various different levels (OF =off). 1. Press w repeatedly until CA is displayed. 2. Scroll to the desired setting (1 -5) using v/V. 3. Press PTT.
Termination tone (Roger tone)
You can activate a tone sequence which is heard when you release the PTT button. This can be used as a reminder to the other person that you have finished talking and are waiting for a response. 1. Press w repeatedly until ro is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Press PTT.

Key Beep

Searching two channels (Dual Watch)
You can enter a different channel for simultaneous listening using the usual main channel. 1. Press w repeatedly until DCM is displayed. 2. Scroll to the desired channel using v/V (OF =off). Press w. 3. Scroll to the desired sub channels using v/V. Press w. 4. Press PTT.
Doro hereby declares that the product Doro BM35 conforms to the essential requirements and other relevant regulations contained in the Directives 1999/5/EC and 2002/95/EC. A copy of the manufacturers declaration is available at www.doro.com/dofc

Troubleshooting

The unit does not activate despite being switched on - Do the batteries require recharging? - Are the batteries inserted correctly? Acoustic Feedback - The units are too close to each other. No sound in handset (parent unit) - Has the same channel and transfer code been selected for both units? - Turn up the volume. - Adjust the level for sound activation (VOX). - Move the units closer to each other (within range).

Guarantee

This product is guaranteed for a period of 12 months from the date of purchase. In the unlikely event of a fault occurring during this period, please contact the place of purchase. Proof of purchase is required for any service or support needed during the guarantee period. This guarantee shall not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, wrong batteries, non-maintenance or any other circumstances on the users part. Furthermore, this guarantee shall not apply to a fault caused by a thunderstorm or any other voltage fluctuations.

Manual

doro bm35

English

Headset socket Torch button Charging socket Button lock Volume/Scroll buttons Call button
Push to Talk (PTT) button Monitor button Microphone
10 Menu button 11 On/Off button 12 Torch Light
Area of use The handset is intended for both indoor and outdoor use, it is NOT resistant to rain, water, rough or other careless treatment. In ideal conditions ie: line of sight with no obstructions between handset/s and monitor, the range can be up to 3 km. Batteries 1. Remove the belt clip by lifting the small locating tab and pushing the clip upwards. 2. Before removing the battery cover release the locking clasp at the base of the handset. 3. Insert the rechargeable battery pack ensuring correct battery polarity is observed. 4. Refit the battery cover and belt clip. Charge the handset for 24 hours before use.

Please note!

The rechargeable battery pack has been installed the handset must be charged for 24 hours before use. Charging bm35 (using adapter) Connect the mains adapter to the socket on the left of the handset and an electrical wall socket. Charging bm35+1 (with charging stand) Connect the mains adapter to the socket on the rear of the charging stand and to an electrical wall socket. Place the handset in the charger with the buttons facing out. Battery indicator and charging The symbol | in the display indicates when the batteries require charging. The indicator has three segments which disappear as the battery charge decreases, and will flash when the battery is running low. Charge the equipment as soon as possible when the indicator flashes! The battery indicator will stop flashing when charging is complete (approximately 14 hours/ initially 24 hours). Fully-charged batteries will last for approximately 30 hours in standby or 2 hours operational time. These times apply at normal room temperature.
Never charge ordinary (non-rechargeable) batteries in the handset, since this will ruin the equipment. The guarantee does not cover this type of damage. The equipment must be charged initially for 24 hours before use during which time the handset cannot be used. The recharging system used in this model may result in it becoming warm. This is normal and will not damage the equipment. Important! Although the baby monitor offers a practical solution in looking after a child it cannot replace a parent or guardian. Make sure the equipment is always out of reach, never place the unit in the childs bed or playpen. To avoid acoustic feedback by not placing the handset and baby monitor close to one another. Radio signals can be blocked if the equipment is used in areas with high sources of interference from other electronic equipment. Regardless of the selected channel or transfer code, you may experience radio chatter from other PMR units within the operating range.

www.doro.com

Belt clip A belt clip is included and fitted to the back of the handset. The belt clip enables the handset to be attached to a belt, waistband or similar. You can remove the belt clip by lifting the small locating tab and pushing the clip upwards. Important! Please note when programming all references to press = to press and then immediately release the button. Switching the Handset on/off Press and hold 1 for a few seconds to turn the handset on or off. To communicate 1. Make sure that all handsets (and monitor unit) are set to the same channel and transfer code. See below. 2. Press and hold PTT (Push To Talk) to speak. Please note! If you are unable to communicate it may be because different channels or transfer codes have been selected, the battery is running low or the units are too far apart. Channel selection All UHF/CB radio equipment share the available designated channels. If the chosen channel is in use select an alternate channel, the selected channel number will be displayed in standby mode. Please refer to the frequency/channel allocation table on page 8. 1. Press w. The current selected channel flashes. 2. Select the desired channel using v/V. 3. Press PTT. Transfer code selection There are 38 transfer codes available which can be used to filter out unwanted signals. However, your conversation may still be overheard irrespective of which code is used. To enable communication between handsets (as well as monitor to handset), the same transfer code must be used on all units. In order to communicate with equipment that cannot select a code, enter code 0. 1. Press w repeatedly until the small digits in the top right hand corner of the display flash. 2. Scroll to the desired transfer code using v/V. 3. Press PTT to confirm. Scanning You can scan all available channels to locate any signals being transmitted. Once a signal has been located the display will show the channel number, and a signal will be heard for a few seconds. You can press PTT to stop at the located channel. Please note: while searching battery consumption will be significantly higher than normal. 1. Press w and { at the same time. The unit will start searching. 2. To stop scanning press w.

Monitor function The monitor function can be used in weak signal areas to locate any other signal being transmitted. 1. Press and hold for at least five seconds. 2. To stop monitoring press PTT. Cordless baby monitor/ Voice control (VOX) This function is practical for use as a baby monitor, i.e. put one handset close to the baby (but out of reach) and carry the other one with you. You can then hear when the sound exceeds the set level of sound sensitivity. Remember to reduce the volume on the unit that is placed close to the baby. This handset can be used without having to press the PTT button to transmit. By setting the correct level, the handset can automatically determine when you are speaking. Test different settings until the sensitivity selected is acceptable. Please note that however accurate your setting there is always a small risk that increased noise from the surroundings may activate the transmitter, this may result in the initial word being unclear. The transmitter will shut off two seconds after you have finished speaking. VOX will be displayed while the function is active. If the handset transmits by itself the sensitivity is set too high and will need to be adjusted. Press w to be able to temporarily interrupt and change the setting. 1. Press w repeatedly until VOX is displayed. 2. Scroll to the desired setting using v/V (OF =off, 1=least sensitive.3=most sensitive). 3. Press PTT to confirm. Call melody You can select different call melodies (OF =off). 1. Press w repeatedly until CA is displayed. 2. Scroll to the desired melody (1 -5) using v/V. 3. Press PTT to confirm. Termination (Roger) tone If selected a beep tone will be heard when you release the PTT button. This can be used as a reminder to the other person that you have finished talking and are waiting for a response. 1. Press w repeatedly until ro is displayed. 2. Scroll to the desired setting using v/V (OF =off, On =on). 3. Press PTT to confirm. Key tone If selected a tone will be heard when the handset buttons are pressed, this can be switched on or off. 1. Press w repeatedly until to is displayed. 2. Scroll to the desired setting using v/V (OF =off, On =on). 3. Press PTT to confirm.
Searching two channels You can enter a different channel for simultaneous listening while using the selected operating channel. 1. Press w repeatedly until DCM is displayed. 2. Scroll to the desired setting using v/V (OF =off). Press w. 3. Scroll to the desired transfer code using v/V Press w. 4. Press PTT to confirm. Key lock This function locks buttons w and v/V to prevent unintentional usage. 1. To activate the key lock press N until the display shows the key symbol. 2. To deactivate the key lock press and hold N until the key symbol disappears.

1. Press w until 00 is displayed. 2. Press { to start the timer. 3. You can display a split time by pressing {. Press { again to revert to the ongoing timer. 4. Press { to stop the timer. 5. Press } to reset the timer. 6. Press w until the display returns to the standby mode.
UK If you cannot resolve the fault using the faultfinder section, technical support is available on the Premium Rate Number: 0114. Calls cost 50 pence per minute (prices correct at the time of going to press), and is operational between 9AM - 5PM Monday-Friday excluding Bank Holidays. Alternatively, E-mail on: tech@doro-uk.com You can contact us in writing: Consumer Support Group, Doro UK Ltd., 22 Walkers Road, North Moons Moat, Redditch, Worcestershire, B98 9HE, (regarding any Spares or Technical query), or Telephoning (Spares only): Web site: www.doro-uk.com Guarantee This product is guaranteed for a period of 12 months from the date of purchase. Proof of purchase is required for any service or support required during the guarantee period. This guarantee shall not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, not reasonably maintained or any other circumstances on the purchasers part. Furthermore, this guarantee shall not apply to a fault caused by a thunderstorm or any other voltage fluctuations. This guarantee does not in any way affect your statutory rights. (As a matter of precaution, we recommend disconnecting the telephone during a thunderstorm.)
Australia and New Zeeland
AUSTRALIA DORO Australia Pty Ltd PO Box 6760 Baulkham Hills BC NSW 2153 Australia Consumer Support Ph: Ph: 023 Fax: (02) 8853-8489 Email: support@doro.com.au Web site: www.doro.com.au
The product complies with AS/NZS 4365.
NEW ZEALAND Atlas Gentech (NZ) Limited Private Bag 14927 Panmure Auckland New Zealand Consumer Support Ph: 0900-500-25 (Toll Call) Fax: (09) 574-2722 Email: support@atlasgentech.co.nz

N13 Z109

www.doro.com

* These channels are the repeater access channels ( mode). ** Designated emergency channels. ! Speech telephony is not permitted on these channels.

English Version 1.0