Restoring Default Settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the computer is not in the Setup Utility, begin at step 1. If the computer is in the Setup Utility, begin at step 2. 1. To open the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, Press <F10> to enter setup, is displayed in the lower-left corner of the screen. 2. Select Exit > Load Setup Defaults, and then press f10. 3. When the Setup Confirmation is displayed, press enter to save your preferences. 4. To set your preferences and exit the Setup Utility, press f10, and then follow the instructions on the screen. The Setup Utility default settings are set when you exit the Setup Utility and go into effect when the computer restarts.
Your password, security, and language settings are not changed when you restore the factory default settings.
Using Advanced Setup Utility Features
This guide describes the Setup Utility features recommended for all users. For more information about the Setup Utility features recommended for advanced users only, refer to the Help and Support Center, which is accessible only when the computer is in Windows. The Setup Utility features available for advanced users include a hard drive self-test, a Network Service Boot, and settings for boot order preferences. The <F12> to boot from LAN message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows or restored from hibernation is the prompt for a Network Service Boot. The Press <ESC> to change boot order message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows or restored from hibernation is the prompt to change the boot order.
Closing the Setup Utility
You can close the Setup Utility with or without saving changes.
To close the Setup Utility and save your changes from the current session, use either of the following procedures:

Replace diskette drive.

Flowchart 2.18Nonfunctioning Keyboard
Keyboard not operating properly.
Connect computer to good external keyboard.
External device works? Replace system board.
Reseat internal keyboard connector (if applicable).
Keyboard operating properly? Replace internal keyboard or cable.
Done Keyboard operating properly? Done
Flowchart 2.19Nonfunctioning Pointing Device
Pointing device not operating properly.
Connect computer to good external pointing device.
Reseat internal pointing device connector (if applicable).
Pointing device operating properly? Replace internal pointing device or cable.
Done Pointing device operating properly? Done
Flowchart 2.20No Network/Modem Connection
No network or modem connection.
Network or modem jack active? Replace jack or have jack activated.
Digital line? Connect to nondigital line.
NIC/modem configured in OS? Reload drivers and reconfigure. Network or modem connection working?
Disconnect all power from the computer and open.
Replace NIC/modem (if applicable).
Reseat NIC/modem (if applicable). Network or modem connection working? Done
Illustrated Parts Catalog
This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers.
3.1 Serial Number Location
When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.

Serial Number Location

3.2 Computer Major Components
Computer Major Components
Table 3-1 Spare Parts: Computer Major Components
Item 1 Description 14.0-inch, WXGA display assembly (includes wireless antenna transceivers and cables) Spare Part Number 417049-001
Section Refer toassembly3.3, Display Assembly Components, for display internal component spare part number information. 2 Switch covers (include wireless button and light) For use with full-featured computer models For use with defeatured computer models Power button board (includes power button board cable) Keyboards For use only with computer models using Intel processors Belgium Brazil Denmark European France French Canada Germany Greece International Israel Italy Japan Korea Latin America 441317-A41 441317-201 441317-081 441317-021 441317-051 441317-121 441317-041 441317-DJ1 441317-B31 441317-BB1 441317-061 441317-291 441317-AD1 441317-161 Nordic Norway Portugal Russia Saudi Arabia Spain Sweden/Finland Switzerland Taiwan Thailand Turkey United Kingdom United States 441317-DH1 441317-091 441317-131 441317-251 441317-171 441317-071 441317-101 441317-111 441317-AB1 441317-281 441317-141 441317-031 441317-001 417077-001 417078-001 430475-001

Spare Part Number 417056-001 417057-001 417058-001 417059-001 417063-001 417064-001 417065-001 417066-001 417067-001 417069-001 417069-041 417069-051 417069-061 417069-071 417069-081 417069-091 Description 5400-rpm, 60-GB hard drive (includes frame and connector) 5400-rpm, 80-GB hard drive (includes frame and connector) 5400-rpm, 100-GB hard drive (includes frame and connector) 5400-rpm, 120-GB hard drive for use only with computer models using Intel processors (includes frame and connector) DVD/CD-RW Combo Drive DVDRW/R and CD-RW Double-Layer Combo Drive DVDRW/R and CD-RW Double-Layer Combo Drive with LightScribe 6-cell, 4.0-Ahr battery 12-cell, 8.8-Ahr battery Keyboard for use with computer models using AMD processors in the United States Keyboard for use with computer models using AMD processors in Germany Keyboard for use with computer models using AMD processors in France Keyboard for use with computer models using AMD processors in Italy Keyboard for use with computer models using AMD processors in Spain Keyboard for use with computer models using AMD processors in Denmark Keyboard for use with computer models using AMD processors in Norway
Spare Part Number 417069-101 417069-121 417069-161 417069-281 417069-AD1 417069-B31 417074-001 417076-001 417077-001 417078-001 417081-001 417082-001 417083-001 417085-001 417089-001 417091-001 Description Keyboard for use with computer models using AMD processors in Sweden/Finland Keyboard for use with computer models using AMD processors in French Canada Keyboard for use with computer models using AMD processors in Latin America Keyboard for use with computer models using AMD processors in Thailand Keyboard for use with computer models using AMD processors in Korea Keyboard for use with computer models using AMD processors internationally Plastics Kit RTC battery Switch cover for use with full-featured computer models (include wireless button and light) Switch cover for use with defeatured computer models (include wireless button and light) Fan/heat sink assembly (include thermal pads) for use only with computer models using Intel processors TouchPad cable Modem module for use only with computer models using Intel processors USB board (includes USB board cable) Speaker assembly Top cover for use with full-featured computer models (includes TouchPad)
Spare Part Number 417092-001 417094-001 417096-001 417097-001 417101-001 417103-001 417105-001 417107-001 417109-001 417111-001 417112-001 417114-001 417330-001 418162-001 430326-001 430453-001 430454-001 430455-001 430456-001 Description Wireless switch board (includes wireless switch board cable) Base enclosure for use with full-featured computer models Rubber Feet Kit (includes computer feet]) Display inverter Display Plastics Kit for use with full-featured computer models (includes display bezel, microphone, and display enclosure) Display Hinge Kit (includes left and right display hinges) Display Screw Kit (includes screws and rubber screw covers) Wireless antenna transceivers and cables Screw Kit Display Label Kit ExpressCard assembly Fan/heat sink assembly mounting bracket HP xb3000 Expansion Base Carrying case Expansion hub 802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, United Arab Emirates, Ukraine. Intel Core Duo T2050 (1.60-GHz) processor (includes thermal pad) Intel Core Duo T2250 (1.73-GHz) processor (includes thermal pad) Intel Core Solo T1350 (1.80-GHz) processor (includes thermal pad)

Spare Part Number 430459-001 430460-001 430461-001 430462-001 430463-001 430464-001 430465-001 430468-001 430470-001 430472-001 430474-001 430475-001 430904-001 430958-001 431483-001 431484-001 431844-001 Description Display panel 5400-rpm, 40-GB hard drive (includes frame and connector) Power connector cable for use only with computer models using Intel processors Power connector cable for use with UMA system boards Fan/heat sink assembly (include thermal pads) for use on UMA system boards TouchPad Audio/infrared board (includes audio/infrared board cable) Top cover for use with defeatured computer models (includes TouchPad) Base enclosure for use with defeatured computer models Display Plastics Kit for use with defeatured computer models (includes display bezel and display enclosure) Cable Kit Power button board (includes power button board cable) Display Cable Kit for use only with computer models using Intel processors Wireless laser mouse System board for use with full-featured computer models using AMD processors Mobile AMD Sempron 3200+ (1.60-GHz) processor (includes thermal pad) System board for use with defeatured computer models using AMD processors
Spare Part Number 431845-001 431846-001 431849-001 431851-001 431852-001 431881-001 435743-001 435836-001 435837-001 435838-001 435848-001 435849-001 436238-001 437780-001 437781-001 438210-001 439128-001 Description AMD Turion ML-50 1.60-GHz processor (includes thermal pad) AMD Turion ML-52 1.60-GHz processor (includes thermal pad) Mobile AMD Sempron 3400+ (1.80-GHz) processor (includes thermal pad) Fan/heat sink assembly for use with computer models using AMD processors (includes thermal paste and pads) Modem module for use with computer models using AMD processors Display lid switch module HP Remote Control USB travel mouse AMD Turion TL-56, 1.80-GHz processor, for V3200 models Mobile AMD Sempron 3500+ (1.80-GHz) processor, for V3200 models Intel Core Duo T5600 (1.83-GHz) processor, V3200 models Intel Core Duo T7200 (2.00-GHz) processor, V3200 models Optical wired mouse Intel Core Duo T5500 (1.66-GHz) processor, for V3200 models Intel Core Duo T5200 (1.60-GHz) processor, for V3200 models AMD Turion 64, MK-36, 2.00-GHz processor, for V3200 models Remote control, ExpressCard
439129-001 439130-001 439131-001 439254-001 440768-001 440769-001 440770-001 Infrared emitter TV tuner, ExpressCard TV tuner antenna Remote control - ExpressCard (EMEA) System board, dv2100 for use with full-featured models System board, dv2100 for use with defeatured models 802.11b/g WLAN Mini Card module for use in the countries or regions listed below. These countries or regions are categorized as most of the world (MOW 1). Antigua & Barbuda Argentina Australia Bahamas Barbados Brunei Canada 440771-001 440772-001 440777-001 440779-001 440781-001 441317-001 441317-021 441317-031 441317-041 Chile Dominican Rep Guam Guatemala Hong Kong Panama India Indonesia Malaysia Mexico New Zealand Paraguay Saudi Arabia Taiwan The United States Vietnam

AMD Turion Dual Core, TL-60, 2.0-GHz processor 6-cell, 2.2-Ahr battery System board, PM/G72M-Z for use with full-featured models System board, GML for use with defeatured models Intel Core Duo T2350 (1.60-GHz) processor, V3200 models Keyboard for use only with computer models using Intel processors in the United States Keyboard for in Europe Keyboard for use only with computer models using Intel processors in the United Kingdom Keyboard for use only with computer models using Intel processors in Germany
Spare Part Number 441317-051 441317-061 441317-071 441317-081 441317-091 441317-101 441317-111 441317-121 441317-131 441317-141 441317-161 441317-171 441317-201 441317-251 Description Keyboard for use only with computer models using Intel processors in France Keyboard for use only with computer models using Intel processors in Italy Keyboard for use only with computer models using Intel processors in Spain Keyboard for use only with computer models using Intel processors in Denmark Keyboard for use only with computer models using Intel processors in Norway Keyboard for use in only with computer models using Intel processors Sweden/Finland Keyboard for use only with computer models using Intel processors in Switzerland Keyboard for use only with computer models using Intel processors in French Canada Keyboard for use only with computer models using Intel processors in Portugal Keyboard for use only with computer models using Intel processors in Turkey Keyboard for use only with computer models using Intel processors in Latin America Keyboard for use only with computer models using Intel processors in Saudi Arabia Keyboard for use only with computer models using Intel processors in Brazil Keyboard for use in Russia
Spare Part Number 441317-281 441317-291 441317-A41 441317-AB1 441317-AD1 441317-B31 441317-BB1 441317-DH1 441317-DJ1 441610-001 441611-001 442171-001 446320-001 Description Keyboard for use only with computer models using Intel processors in Thailand Keyboard for use in Japan Keyboard for use only with computer models using Intel processors in Belgium Keyboard for use only with computer models using Intel processors in Taiwan Keyboard for use only with computer models using Intel processors in Korea Keyboard for use only with computer models using Intel processors internationally Keyboard for use only with computer models using Intel processors in Israel Keyboard for use Nordic countries or regions (English, Danish, Finnish, Norwegian, Swedish) Keyboard for use in Greece Intel Core Duo T2060 (1.60-GHz) processor, V3200 models 6-cell, 2.55-Ahr battery 5400-rpm, 160-GB hard drive System board, 943GML for use with defeatured models

Removing a Mini Card Module
Reverse the above procedure to install a Mini Card module.

5.9 Optical Drive

Optical Drive Spare Part Number Information
DVD/CD-RW Combo Drive DVDRW/R and CD-RW Double-Layer Combo Drive DVDRW/R and CD-RW Double-Layer Combo Drive with LightScribe 417063-001 417064-001 417065-001
1. Prepare the computer for disassembly (Section 5.3). 2. Remove the Phillips PM2.57.0 screw 1 that secures the optical drive to the computer. 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2. (The optical drive media tray releases from the optical drive.) 4. Use the media tray frame to slide the optical drive 3 to the left. 5. Remove the optical drive.
Removing the Optical Drive
Maintenance and Service Guide 519
6. Position the optical drive with the optical drive bracket toward you. 7. Remove the two Phillips PM2.03.0 screws 1 that secure the optical drive bracket to the optical drive. 8. Remove the optical drive 2.
Removing the Optical Drive Bracket
Reverse the above procedure to reassemble and install the optical drive.

Keyboard

Keyboard Spare Part Number Information
For use with all computer models: Denmark France French Canada Germany International Israel Italy 441317-081 441317-051 441317-121 441317-041 441317-B31 441317-BB1 441317-061 Korea Latin America Norway Spain Switzerland The United Kingdom The United States 441317-AD1 441317-161 441317-091 441317-071 441317-111 441317-031 441317-001
For use only with computer models using Intel processors: Belgium Brazil European Greece Japan Nordic Portugal 441317-A41 441317-201 441317-021 441317-DJ1 441317-291 441317-DH1 441317-131 Russia Saudi Arabia Sweden/Finland Taiwan Thailand Turkey 441317-251 441317-171 441317-101 441317-AB1 441317-281 441317-141
For use only with computer models using AMD processors: Denmark France French Canada Germany International Italy Korea 417069-081 417069-051 417069-121 417069-041 417069-B31 417069-061 417069-AD1 Latin America Norway Spain Sweden/Finland Thailand The United States 417069-161 417069-091 417069-071 417069-031 417069-281 417069-001
1. Prepare the computer for disassembly (Section 5.3).
2. Remove the three Phillips PM2.57.0 screws that secure the keyboard to the computer.
Removing the Keyboard Screws
3. Turn the computer display-side up with the front panel toward you. 4. Open the computer as far as possible.
5. Slide the keyboard 1 back to release the tabs on the front of the keyboard from the top cover. 6. Lift the rear edge of the keyboard 2 and swing it forward until it rests on the palm rest.

Releasing the Keyboard

7. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board.

24. If it is necessary to replace the wireless transceivers and cables, remove the two Phillips PM2.54.0 screws 1 that secure the left and right transceivers to the display enclosure. 25. Remove the wireless antenna cables from the clips 2 built in to the left and right sides of the display enclosure. 26. Detach the wireless antenna transceivers 3 from the display enclosure. 27. Remove the wireless antenna cables 4.
Removing the Wireless Antenna Transceivers and Cables
microphone and cable are included The spare part number 430904-001. in the Display Cable Kit, 28. If it is necessary to replace the microphones and cables, release the retention tabs 1 built in to the display enclosure lining that secure the microphones and cables to the display enclosure. 29. Remove the microphones from the clips 2 in the display enclosure. 30. Remove the microphone cables 3 from the display enclosure.

Removing the Microphones

Reverse the above procedure to reassemble and install the display assembly

Top Cover

Top Cover Spare Part Number Information
Top cover (include TouchPad)

417091-001

1. Prepare the computer for disassembly (Section 5.3) and remove the following components:
Hard drive (Section 5.4) Mini Card compartment cover (Section 5.8) Optical drive (Section 5.9) Keyboard (Section 5.10) Switch cover (Section 5.11) Display assembly (Section 5.12)
2. Remove the six Phillips PM2.59.0 screws 1 and the Phillips PM2.57.0 screw 2 that secure the top cover to the computer.
Removing the Top Cover Screws, Part 1
542 Maintenance and Service Guide
3. Remove the two Phillips PM2.03.0 screws 1 and the four Phillips PM2.04.0 screws 2 that secure the top cover to the computer.
Removing the Top Cover Screws, Part 2
4. Turn the computer right-side up with the front toward you. 5. Release the ZIF connector 1 to which the TouchPad cable is connected and disconnect the cable 2 from the system board.
Disconnecting the TouchPad Cable
6. Remove the two Phillips PM2.04.0 screws 1 and the Phillips PM2.59.0 screw 2 that secure the top cover to the computer.

Removing the Audio/Infrared Board
Reverse the above procedure to install the audio/infrared board.

Bluetooth Module

Bluetooth Module Spare Part Number Information
Bluetooth module (includes Bluetooth module cable) 397923-002
Hard drive (Section 5.4) Mini Card compartment cover (Section 5.8) Optical drive (Section 5.9) Keyboard (Section 5.10) Switch cover (Section 5.11) Display assembly (Section 5.12) Top cover (Section 5.13) Audio/infrared board (Section 5.17)
2. Disconnect the Bluetooth module cable 1 from the system board. 3. Remove the Bluetooth module 2.
Removing the Bluetooth Module
Reverse the above procedure to install the Bluetooth module.

USB Board

USB Board Spare Part Number Information
USB board (includes USB board cable)

417085-001

2. Disconnect the USB board cable 1 from the system board. 3. Remove the silver Phillips PM2.55.0 screw 2 that secures the USB board to the computer. 4. Lift the USB board 3 straight up to remove it from the computer. 5. Remove the num lock light 4 from the clip in the base enclosure

Removing the USB Board

Reverse the above procedure to install the USB board.

5.20 Speaker Assembly

Speaker Assembly Spare Part Number Information
Speaker assembly 417089-001
Hard drive (Section 5.4) Mini Card compartment cover (Section 5.8) Optical drive (Section 5.9) Keyboard (Section 5.10) Switch cover (Section 5.11) Display assembly (Section 5.12) Top cover (Section 5.13) USB board (Section 5.19)
2. Disconnect the speaker cable 1 from the system board. 3. Remove the four Phillips PM2.54.0 screws 2 that secure the speakers to the computer. 4. Lift the speakers 3 straight up to remove them from the computer.
Removing the Speaker Assembly
Reverse the above procedure to install the speaker assembly.

5.21 System Board

System Board Spare Part Number Information
For use only with computer models using Intel processors: PM/G72M-V for use with full-featured computer models using Intel processors GM for use with full-featured computer models using Intel processors GMZ for use with defeatured computer models using Intel processors PM/G72M-Z for use with full-featured models dv2100 for use with full-featured computer models GML for use with defeatured computer models dv2100 for use with defeatured computer models 943GML for use with defeatured computer models For use only with computer models using AMD processors: For use with full-featured computer models For use with defeatured computer models 431483-001 431844-001 417035-001 417036-001 417037-001 440777-001 440768-001 440779-001 440769-001 446320-001

Fan/Heat Sink Assembly Spare Part Number Information
For use with computer models using Intel processors: For use on UMA system boards For use on discrete system boards For use with computer models using AMD processors 430463-001 417081-001 431851-001
Hard drive (Section 5.4) Optical drive (Section 5.9) Keyboard (Section 5.10) Switch cover (Section 5.11) Display assembly (Section 5.12) Top cover (Section 5.13) System board (Section 5.21)
2. Turn the computer upside down with the front toward you. 3. Disconnect the fan cable from the system board.
Disconnecting the Fan Cable
4 and 5 apply Stepsprocessors. only to computer models using Intel 4. Loosen the four Phillips PM2.013.0 screws 1 and the Phillips PM2.09.0 screw 2 that secure the fan/heat sink assembly to the system board. 5. Remove the fan/heat sink assembly 3 from the system board.
Removing Fan/Heat Sink Assembly
and 7 apply Steps 6processors. only to computer models using AMD 6. Loosen the Phillips PM2.09.0 screw 1 and the four Phillips PM2.013.0 screws 2 that secure the fan/heat sink assembly to the system board. 7. Remove the fan/heat sink assembly 3 from the system board.
The following note applies only to computer models using Intel processors:
The thermal pads should be thoroughly cleaned from the surfaces of the fan/heat sink assembly 1 and 3, video memory chip 2, and processor 4 each time the fan/heat sink assembly is removed. Thermal pads should be installed on all surfaces before the fan/heat sink assembly is reinstalled. Thermal pads are included with all fan/heat sink assembly, system board, and processor spare part kits.
Replacing the Thermal Pads
The following note applies only to computer models using AMD processors:
Reverse the above procedure to install the fan/heat sink assembly.
The fan/heat sink assembly mounting bracket should be replaced as shown in the following illustration when installing the fan/heat sink assembly. The fan/heat sink assembly mounting bracket is available using spare part number 417114-001.
Removing the Fan/Heat Sink Assembly Mounting Bracket

5.24 Processor

Processor Spare Part Number Information
Intel Core Duo T7200 (2.00-GHz), use with V3200 models Intel Core Duo T5600 (1.83-GHz), use with V3200 models Intel Core Duo T5500 (1.66-GHz), use with V3200 models Intel Core Duo T5200 (1.60-GHz), use with V3200 models Intel Core Duo T2600 (2.16-GHz) Intel Core Duo T2500 (2.00-GHz) Intel Core Duo T2400 (1.83-GHz) Intel Core Duo T2250 (1.73-GHz) Intel Core Duo T2300 (1.66-GHz) Intel Core Duo T2050 (1.60-GHz) Intel Core Duo T2350 (1.60-GHz), use with V3200 models Intel Core Duo T2060 (1.60-GHz), use with V3200 models Intel Core Solo T1350 (1.80-GHz) Intel Celeron M 440 (1.86-GHz), use with V3200 models Intel Celeron M 430 (1.73-GHz), use with V3200 models AMD Turion Dual Core, TL-60, 2.0-GHz, use with V3200 models AMD Turion 64, MK-36, 2.00-GHz, use with V3200 models AMD Turion TL-56, 1.80-GHz, use with V3200 modelsAMD Turion ML-52 1.60-GHz AMD Turion ML-50 1.60-GHz Mobile AMD Sempron 3500+ (1.80-GHz), use with V3200 models Mobile AMD Sempron 3400+ (1.80-GHz) Mobile AMD Sempron 3200+ (1.60-GHz) 435849-001 435848-001 437780-001 437781-001 417044-001 417043-001 417042-001 430455-001 417041-001 430454-001 440781-001 441610-001 430456-001 440780-001 435851-001 440771-001 438210-001 435837-001 431846-001 431845-001 435838-001 431849-001 431484-001

Table 6-9 System I/O Addresses (Continued)
I/O Address (hex) 0x000001F0-0x000001F7 0x00000220-0x0000022F 0x00000274-0x00000277 0x00000279-0x00000279 0x00000280-0x00000293 0x00000376-0x00000376 0x000003B0-0x000003BB 0x000003B0-0x000003BB 0x000003C0-0x000003DF 0x000003C0-0x000003DF 0x000003F6-0x000003F6 0x0000040B-0x0000040B 0x000004D0-0x000004D1 0x000004D6-0x000004D6 0x00000530-0x00000537 0x00000870-0x0000087F 0x00000A79-0x00000A79 0x00000C00-0x00000C01 0x00000C14-0x00000C14 0x00000C50-0x00000C52 0x00000C6C-0x00000C6C System Function (shipping configuration) Primary IDE Channel System board resources ISAPNP Read Data Port ISAPNP Read Data Port System board resources Secondary IDE Channel PCI standard PCI-to-PCI bridge ATI MOBILITY RADEON Xpress 200 Series PCI standard PCI-to-PCI bridge ATI MOBILITY RADEON Xpress 200 Series Primary IDE Channel System board resources System board resources System board resources System board resources System board resources ISAPNP Read Data Port System board resources System board resources System board resources System board resources
I/O Address (hex) 0x00000C6F-0x00000C6F 0x00000CD4-0x00000CD5 0x00000CD6-0x00000CD7 0x00000CD8-0x00000CDF 0x00000D00-0x0000FFFF 0x00000F40-0x00000F47 0x00001080-0x00001080 0x00008000-0x0000805F 0x00008100-0x000081FF 0x00008400-0x0000840F 0x00008410-0x0000841F 0x00009000-0x00009FFF 0x00009000-0x00009FFF 0x0000A000-0x0000A0FF 0x0000F000-0x0000FFFF 0x0000FD00-0x0000FDFF 0x0000FE00-0x0000FEFF System Function (shipping configuration) System board resources System board resources System board resources System board resources PCI bus System board resources System board resources System board resources System board resources ATI SMBus Standard Dual Channel PCI IDE Controller PCI standard PCI-to-PCI bridge ATI MOBILITY RADEON Xpress 200 Series Realtek RTL8139/810x Family Fast Ethernet NIC PCI standard PCI-to-PCI bridge Texas Instruments PCIxx21/x515 Cardbus Controller Texas Instruments PCIxx21/x515 Cardbus Controller
Table 6-10 System Memory Map
Memory Map Address (hex) 0xD4100000-0xD41FFFFF 0xD4100000-0xD41FFFFF 0xD8000000-0xDBFFFFFF 0xD8000000-0xDBFFFFFF 0xFAC00000-0xFEBFFFFF 0xF6C00000-0xFABFFFFF 0xD4000000-0xD4000FFF 0xD4001000-0xD4001FFF 0xD4002000-0xD4002FFF 0xD4003000-0xD40033FF 0xFFF80000-0xFFFFFFFF 0xE0000000-0xE03FFFFF 0xE0000000-0xE03FFFFF 0x0000-0x0FFF 0xD4208000-0xD42087FF 0xD4200000-0xD4203FFF 0xD4204000-0xD4205FFF 0xFFEFF000-0xFFEFFFFF 0xFFEFE000-0xFFEFEFFF System Function (shipping configuration) PCI standard PCI-to-PCI bridge ATI MOBILITY RADEON Xpress 200 Series PCI standard PCI-to-PCI bridge ATI MOBILITY RADEON Xpress 200 Series PCI standard PCI-to-PCI bridge PCI standard PCI-to-PCI bridge Standard OpenHCD USB Host Controller Standard OpenHCD USB Host Controller Standard Enhanced PCI to USB Host Controller ATI SMBus System board System board System board resources System board Texas Instruments OHCI Compliant IEEE 1394 Host Controller Texas Instruments OHCI Compliant IEEE 1394 Host Controller Broadcom 802.11b/g WLAN Texas Instruments PCIxx21/x515 Cardbus Controller Texas Instruments PCIxx21/x515 Cardbus Controller

Phillips PM2.59.0 Screw Locations
Table A-6 Phillips PM2.59.0 Screw (Continued)
Where used: One screw that secures the display assembly to the computer (documented in Section 5.12)
Phillips PM2.59.0 Screw Location
Where used: 6 screws that secure the top cover to the computer (documented in Section 5.13)
Table A-7 Silver Phillips PM2.55.0 Screw

Qty. 3

Where used: One screw that secures the switch cover to the computer (documented in Section 5.11)
Silver Phillips PM2.55.0 Screw Location
Table A-7 Silver Phillips PM2.55.0 Screw (Continued)
Where used: One screw that secures the audio/infrared board to the computer (documented in Section 5.17)
Where used: One screw that secures the USB board to the computer (documented in Section 5.19)
Table A-8 Phillips PM2.04.0 Screw

Length 4.0 mm

Where used: 4 screws that secure the top cover to the computer (documented in Section 5.13)
Phillips PM2.04.0 Screw Locations
Table A-8 Phillips PM2.04.0 Screw (Continued)
Where used: 2 screws that secure the modem module to the computer (documented in Section 5.16)
Where used: 2 screws that secure the ExpressCard assembly to the system board (documented in Section 5.22)
Table A-9 Phillips PM2.02.0 Screw

Qty. 2

Length 2.0 mm
Where used: 2 screws that secure the TouchPad board to the TouchPad bracket (documented in Section 5.14)
Phillips PM2.02.0 Screw Locations
Table A-10 Phillips PM2.54.0 Screw
Where used: 4 screws that secure the speaker assembly to the computer (documented in Section 5.20)
Phillips PM2.54.0 Screw Locations
Table A-11 Phillips PM2.08.0 Screw

Length 8.0 mm

Phillips PM2.08.0 Screw Locations
Table A-12 Phillips PM2.013.0 Spring-Loaded Shoulder Screw

Qty. 8

Length 13.0 mm
Where used: 4 screws that secure the fan/heat sink assembly to the system board on computer models using Intel processors (documented in Section 5.23)
Phillips PM2.013.0 Spring-Loaded Shoulder Screw Locations

Create system restore points using Windows XP Professional System Restore feature. Store personal files in the My Documents folder and back up these folders periodically. Back up templates stored in their associated programs. Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time saver if you have to reset your preferences. To copy the screen and paste it into a Word document: a. Display the screen. b. Copy the screen: To copy only the active window, press alt+fn+prt sc. To copy the entire screen, press fn+prt sc. c. To paste the copied images into a document, open Word, and then select Edit > Paste.
Using System Restore Points
When you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system. earlier point affect Recovering to ancreated restorethe lastdoes notpoint. data files saved or e-mails since restore You also can create additional restore points to provide increased protection for your system files and settings.
When to Create Restore Points
Before you add or extensively modify software or hardware. Periodically, whenever the system is performing optimally.
to If you revertthe a restore point and then change your mind, you can reverse restoration.
Creating a System Restore Point
1. Select Start > Help and Support > System Restore. The System Restore window opens. 2. Click Create a restore point, and then click Next. 3. Follow the on-screen instructions.
Restoring to a Previous Date and Time
To revert to a restore point (created at a previous date and time), when the computer was functioning optimally: 1. Select Start > Help and Support > System Restore. The System Restore window opens. 2. Click Restore my computer to an earlier time, and then click Next. 3. Follow the on-screen instructions.

Creating Recovery Discs

PC Recovery Disc Creator creates a set of recovery CDs or DVDs for the computer. Use recovery discs to restore the operating system and software programs to factory settings, in case of system failure or instability. keep them safe place. The Handle these discs carefully andonly one setin arecovery discs. software allows the creation of of Note the following guidelines before creating recovery discs:
You will need high quality CD-R, DVD-R, or DVD+R media (purchased separately).
and double-layer DVDRW are DVDRW/RRecovery Disc Creator software. not compatible with the PC
The computer must be connected to AC power during this process. Only one set of recovery discs can be created per computer.
Number each disc before inserting it into the computer optical drive. If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open PC Recovery Disc Creator, you will be prompted to continue the disc creation process.

Cable Kit, spare part number 334 cables, service considerations 42 caps lock key 112 carrying case, spare part number 325, 333 CMOS clearing 15 components bottom 117 front 17
backpack, spare part number 324, 327 Backup and Recovery Windows Vista C1 Windows XP B1 backup suggestions B2, C2 base enclosure, spare part numbers 311, 333, 334

Index1

keyboard 111 left-side 19 rear 19 right-side 18 top 113, 115 composite S-Video and audio input cable, spare part number 324, 327 computer feet, locations 511 Computer Setup Advanced Menu 29, 216 File Menu 27, 214 Security Menu 27, 214 Tools Menu 28, 215 computer specifications 61 connector pin assignments external monitor D4 headphone D6 microphone D6 monitor D4 RJ-11 (modem) D5 RJ-45 (network) D2 S-Video-out D3 Universal Serial Bus (USB) D1 connectors, service considerations 42 creating recovery discs Windows Vista C4 Windows XP B4 system restore point Windows Vista C3 Windows XP B3
deleting recovery partition Windows Vista C8 Windows XP B9 design overview 119 disassembly sequence chart 52 diskette drive, OS loading problems 231 display assembly removal 530 spare part number 33, 330, 530 specifications 63 display bezel, removal 534 Display Cable Kit, spare part number 319, 334, 541 Display Hinge Kit, spare part number 319, 333, 537 display hinge, removal 537 Display Label Kit, spare part number 319, 333 display lid switch module removal 538 spare part number 319, 335, 538 display panel removal 539 spare part number 319, 334, 539 Display Plastics Kit, spare part numbers 319, 333, 334, 534 Display Screw Kit, spare part number 319, 333

Index2

docking device, spare part number 324, 333 docking device, troubleshooting 226 drives, preventing damage 43 DVB-T TV tuner antenna, spare part number 324, 329 DVB-T TV tuner, spare part number 324, 329 DVD/CD-RW Combo Drive OS loading problems 232 precautions 43 removal 519 spare part number 313, 321, 331, 519 specifications 67 DVDRW/R and CD-RW Combo Drive OS loading problems 232 precautions 43 removal 519 spare part numbers 313, 321, 331, 519 specifications 69
ExpressCard slot 110 ExpressCard slot bezel, illustrated 322 external monitor port location 110 pin assignments D4
fan/heat sink assembly removal 570 spare part numbers 311, 332, 334, 335, 570 fan/heat sink assembly mounting bracket installing 576, 577 spare part number 311, 333, 576, 577 features 12 feet, locations 511 flowcharts, troubleshooting no audio 233, 234 no network/modem connection 238 no OS loading 227 no OS loading from diskette drive 231 no OS loading from hard drive 228, 229, 230 no OS loading from optical drive 232 no power 220, 222, 223 no video 224, 225 nonfunctioning device 235 nonfunctioning docking device 226

HP xb3000 Notebook Expansion Base

Datasheet

A desktop experience without the clutter The ultimate multimedia experience Expanded connectivity and access Adjustable height capability Integrated speakers in the base
Compatibility: The xb3000 Notebook Expansion Base is compatible with all HP Pavilion dv2000, dv6000, dx6000, dv9000, tx1000, tx2000 and Compaq Presario V3000 and V6000 series notebooks. Technical Specifications: Vertical docking station with adjustable height capability. Integrated Altec Lansing stereo speakers 6 USB ports 1 RJ45 port 1 VGA port S-Video port 1 Composite Video port 1 set of Component Video6 out ports 1 headphone jack 1 S/PDIF (Sony/Philps Digital Interace) port 1 stereo microphone port 1 65W/90W AC adpater power jack (supports the notebook's AC Adapter) 1 Kensington lock slot Integrated Consumer IR port (for optional remote control) on-board volume controls support for optional Hard Drive accesory kit (sold separately) What's in the Box? HP xb3000 Notebook Expansion Base CD User guide Quick Setup Poster Warranty guide Warranty & Support: One-year, worldwide parts-and-labor limited warranty 24x7 HP technical phone support during warranty period Features & Benefits: Get a desktop experience without the clutter: Use your notebook's display as your monitor and save deskspace and adjust the height to a position that is comfortable for you. Neatly stay connected to your peripherals, power and the Internet with just one connection to your notebook. Charge your notebook's battery while connected to the Expansion Base. Transform your notebook into the ultimate multimedia experience: Integrated premium Altec Lansing speakers provide room-filling stereo sound for experiencing movies and music. A variety of audio and video out ports3 provide flexibility to connect your notebook to your home entertainment system. Integrated consumer IR allows you to control media from the palm of 01/28/_r3 rk 2008 Hewlett-Packard Company 3 your hand when used supported optional (sold separately) HP Mobile Only 1 video output option can bewith the at one time. Only 1 audio ouput option port can be supported at one time. 5 When the expansion base is connected the VGA port on the notebook is disabled Remote Control
and monitor must be connected only to the expansion base.6 Component video out is only supported on select notebook models.
Features & Benefits: Get a desktop experience without the clutter: Use your notebook's display as your monitor and save deskspace and adjust the height to a position that is comfortable for you. Neatly stay connected to your peripherals, power and the Internet with just one connection to your notebook. Charge your notebook's battery while connected to the Expansion Base. Transform your notebook into the ultimate multimedia experience: Integrated premium Altec Lansing speakers provide room-filling stereo sound for experiencing movies and music. A variety of audio and video out ports3 provide flexibility to connect your notebook to your home entertainment system. Integrated consumer IR allows you to control media from the palm of your hand when used with the optional (sold separately) HP Mobile Remote Control Expanded connectivity and access give you multiple options: 6 USB ports let you stay connected to all your peripherals. Ethernet port lets you stay connected to the Internet or home network. Pre-formatted optional (sold separately) high capacity hard drive accessory kit for expanded storage.
Dimensions & Weight: In collapsed state: Length: 17.95in Width: 12.91in Height: 4.80in Weight (xb3000 only): 4.932kg Additional Information: Questions about the HP xb3000 Notebook Expansion Base? Look us up online at www.hp.com Part Number: ES235AA
Notebook not included. All hardware and software specifications are subject to change without notice. HP and the invent signature are trademarks of the Hewlett-Packard Company. All other products names mentioned herein may be trademarks of their respective companies. 2008 Hewlett-Packard Company. All rights reserved. Works with Genuine Windows 2000, 98, ME, and XP.
Expanded connectivity and access give you multiple options:
6 USB ports let you stay connected to all your peripherals. Ethernet port lets you stay connected to the Internet or home network.