Leporello, 85x165 mm, 14 pages, 2/2c = black + HKS43N

cruZer 4

99507069_Cruzer4_Z60_China 15

26.03.2010 13:34:15 Uhr

4a 4b 6 8
99507069_Cruzer4_Z60_China 2

26.03.2010 13:34:09 Uhr

99507069_Cruzer4_Z60_China 3

26.03.2010 13:34:10 Uhr

99507069_Cruzer4_Z60_China 4
99507069_Cruzer4_Z60_China 5

26.03.2010 13:34:11 Uhr

99507069_Cruzer4_Z60_China 6
99507069_Cruzer4_Z60_China 7
99507069_Cruzer4_Z60_China 8

26.03.2010 13:34:12 Uhr

99507069_Cruzer4_Z60_China 9
99507069_Cruzer4_Z60_China 10

English

Our products are designed to meet the highest standards of quality, functionality and design. We hope you entirely enjoy your Braun shaver. Please read the use instruction carefully and thoroughly before using the appliance. Warning Your shaver is provided with a special cord set with an integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it. Otherwise there is risk of electric shock. This appliance is not intended for use by children or persons with reduced physical, sensory or mental capabilities, unless they are given supervision by a person responsible for their safety. In general, we recommend that you keep the appliance out of reach of children. Children should be supervised to ensure that they do not play with the appliance. For usage in other body areas, please make sure that the skin is stretched. For hygienic reasons, do not share this appliance with other persons. Oil bottle Keep out of reach of children. Do not swallow. Dispose of properly when empty.

Description

4a 4b 9 Foil protection cap Shaver foil Cutter block Rotating styler Wide shaper (28 mm) Narrow shaper (14 mm) Charging light On/off switch Trimming attachment Beard length selector Special cord set

Charging

The best environmental temperature for charging is between 15 C and 35 C. Do not expose the shaver to temperatures higher than 50C for extended periods of time. 11
99507069_Cruzer4_Z60_China 11

26.03.2010 13:34:13 Uhr

Using the special cord set, connect the shaver to an electrical outlet with the motor switched off. When charging for the first time or when the appliance is not used for a few months, leave the appliance to charge continuously for 4 hours. The charging light (5) shows that the appliance is being charged. When the battery is fully charged, the charging light turns off. Intermittent blinking after a while indicates that the battery maintains its full capacity. This can also happen short term when charging after the battery was completely discharged. A full charge provides 30 minutes of cordless shaving time depending on your beard growth. Once the shaver is completely charged, discharge the shaver through normal use. Then recharge to full capacity. Subsequent charges will take about 1 hour. Maximum battery capacity will only be reached after several charging/discharging cycles. 5-minute quick charge is sufficient for a shave.

Shaving

First, remove the trimming attachment (7): Using your thumbs, press against the side clips of the trimming attachment so that they swing off in the direction of the arrows (a). Activate the on/off switch (6). The floating foil frame automatically adapts to your skin surface for a close, smooth shave. For best results: Always shave before washing your face. At all times, hold the shaver at right angles (90) to the skin (b). Stretch the skin and shave against the direction of beard growth. For pre-shaving after a few days of not having shaved, use the wide shaper (4a) to pre-cut long hairs. For a close, smooth shave, finish with the foil. To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. This appliance is suitable for use in a bath or shower. When using it in the shower, we recommend applying shaving foam or gel. 12
99507069_Cruzer4_Z60_China 12

26.03.2010 13:34:14 Uhr

Using the rotating styler The wide shaper (4a) evenly cuts and trims large areas (c). It is ideal for shaping sideburns, moustaches and partial short beards. The wide shaper is provided with safety rips and a gliding strip for less irritation and easy gliding. Press the blue stripes to push up the rotating styler (4). While stretching the skin, guide the wide shaper against the direction of hair growth. The narrow shaper (4b) precisely defines lines and edges (d), being ideal for precise contouring. To use the narrow shaper, push up the styler and turn it 180. Frequent use of the styler will reduce the battery capacity. Using the trimming attachment The trimming attachment (7) is ideal for beard trimming and keeping it at a constant length. Place the trimming attachment onto the shaver foil (2) and press it against the shaver housing until it snaps into place with a click. Press the beard length selector (8) (e) and slide it up in order to set the desired beard length (length settings from top to bottom 1.2 mm, 2.8 mm, 4.4 mm, 6 mm). Push up the styler (4). Activate the on/off switch and trim against hair growth by guiding the transparent comb part over the skin.

Cleaning

Regular cleaning ensures better shaving performance. Rinsing the shaving head after each shave under running water is an easy and fast way to keep it clean: Switch the shaver on (cordless) and rinse the shaving head under hot running water (f). A natural based soap may also be used provided it contains no particles or abrasive substances. Rinse off all foam and let the shaver run for a few more seconds. Next, switch off the shaver, remove the shaver foil and the cutter block. Then leave the disassembled shaving parts to dry. If you regularly clean the shaver under water, then once a week apply a drop of light machine oil onto the long hair trimmer and shaver foil (h). 13
99507069_Cruzer4_Z60_China 13
Alternatively, you may clean the shaver using the brush provided (g): Switch off the shaver. Remove the shaver foil. Using the brush, clean the cutter block and the inner area of the shaver head. However, do not clean the shaver foil with the brush as this may damage the foil.
Keeping your shaver in top shape
Replacing the shaving parts To maintain 100% shaving performance, replace your foil and cutter block at least every 18 months or when worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil and cutter block: 20 BL) Preserving the batteries In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every 6 months approximately. Then recharge the shaver to full capacity.

Environmental notice

This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country. Subject to change without notice. For electric specifications, see printing on the special cord set.

99507069/III-10 China/GB

99507069_Cruzer4_Z60_China 14