WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law.
WARNING! Never disassemble or adjust the unit.
WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water.
WARNING! Never use irregular discs.

Whats in the Box

1. 2. 3. 4. 5. 6. 7. 8. 9. UV9 Head Unit Single DIN sleeve Wiring harness Parking brake sensor extension wire Mounting hardware Cosmetic trim ring Remote Control Owners Manual Quick Start Guide
WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor.
WARNING! Using an improper fuse may cause damage to the unit and result in a fire.
WARNING! The monitor employs an automatic motorized mechanism. To prevent damage to the core mechanism, please do not push, pull or swivel the monitor manually.

Tools and Supplies

You will need these tools and supplies to install your UV9: Torx type, flat-head and Philips screwdrivers Wire cutters and strippers Tools to remove existing radio (screwdriver, socket wrench set or other tools) Electrical tape Crimping tool Volt meter/test light Crimp connections 18 gauge wire for power connections gauge speaker wire
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the UV9 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.
WARNING! Only connect the unit to a12-volt power supply with proper grounding.

WIRING DIAGRAM

Rear View Video Camera

Rear Video

SUR- L

YELLOW

FRONT R

External Power Amplifier

FRONT L

SUBWOOFER

VIDEO OUT

Antenna Jack

CAMERA
Harness Cord Auto antenna control (connect to antenna control lead & power supply of antenna amplifier)
NAV101/NAV102 Connector (optional equipment)
Steering Wheel Control (SWC) requires PAC SWI-PS Interface Adapter, Sold Separately

Antenna

ANT.CONT

BLUE/WHITE

P.CONT
External power amplifier control

PARKING BRAKE

PRK SW

Car Phone

Mute (leave open if not connected) Car

GREEN/WHITE

P R N D 2 L

REVERSE +

Gearbox Switch Ground Ignition Switch
WHITE + WHITE/BLACK GREY + GREY/BLACK PURPLE + PURPLE/BLACK GREEN +

FRONT L+ FRONT L-

BATTERY + FUSE (15A)
FRONT R+ FRONT RREAR R+ REAR RREAR L+

REAR R

Battery BLACK BATTERY Ground

GREEN/BLACK -

REAR L

REAR L-

UV9 INSTALLATION

Pre-installation

1. Press the metal levers on both sides to remove the halfsleeve from the radio. PREPARE RADIO CAUTION! Be careful not to damage the car wiring. 3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. FINAL INSTALLATION

Wiring

Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.

OPE N DISP AS/P S

SERIE S
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The UV9 uses one 10 amp mini-ATM fuse, located in the black filter box in-line with the main wire harness.

A/V INPU T

A/V INPUT

Final Installation

2. Install the half-sleeve. a. Install adapter if necessary (optional). b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow. c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard. d. Install support strap to make the unit more stable. After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 1. 2. 3. Connect wiring adapter to existing wiring harness. Connect antenna lead. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place.
Final ISO-DIN Installation
1. 2. 3. 4. Remove trim ring. Mount factory brackets on new radio using existing screws from old radio. Slide radio chassis into dash opening and secure. Reinstall dash panel.
FINAL ISO-DIN INSTALLATION

INSTALL HALF SLEEVE

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 20 of horizontal. Make sure the unit is mounted within this limitation.

OPEN DISP

Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.

UV9 REMOTE CONTROL

Table 1: Remote Control Functions Button Name
MENU TITLE MUTE POWER/ AUDIO REPT A-B

Function Ref#

Enters the main menu of the disc Enters the title menu of the disc Toggles on/off audio output Turns the power on/off Changes the audio language for disc playback Setup to repeat playback from time frame A to time frame B Repeats playback of current chapter Selects playing mode Language selection for subtitle Displays playing information Plays back disc in different angle for a scene Fast forwards the disc content Decreases volume Increases volume Selects the previous chapter for playback Pauses playback/starts playback Selects the next chapter for playback Stops playback Goes to specific time frame and playback Slow playback/slow rewind playback Zooms in/out on an image Displays set-up parameters
Turns on/off PBC when playing VCD Plays first ten seconds of each chapter/title Toggles on/off audio output Turns the power on/off

CD/MP3/USB

Toggles on/off audio output Turns the power on/off
Setup to repeat playback from time frame A to time frame B Repeats playback of current chapter Selects playing mode Selects playing mode Repeats playback of current track Selects playing mode

REPT A-B

REPT SRC SUBTITLE DISP ANGLE
Displays playing information Plays back Picture CD with different angle of picture displayed Fast forwards the disc content Decreases volume Increases volume Selects the previous chapter for playback Pauses playback/starts playback Selects the next chapter for playback Stops playback Goes to specific time frame and playback Slow playback/slow rewind playback Zooms in/out on an image Displays set-up parameters
Displays playing information
Display playing information

12 VOL VOL + 15

Fast forwards the disc content Decreases volume Increases volume Searches an available radio station by decreasing tuning frequency Decreases volume Increases volume Selects the previous track for playback Pauses playback/starts playback Searches an available radio station by increasing tuning frequency Selects FM/AM band Selects the next track for playback Stops playback

BAND GOTO

NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.

ZOOM PIC

25 Ejects disc Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: FULL or NORMAL Directly accesses chapter

Ejects disc

Ejects disc Decreases monitor tilt angle Increases monitor tilt angle
Decreases monitor tilt angle Increases monitor tilt angle Selects display mode: FULL or NORMAL
DISP 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (Numeric Keypad) CLEAR
1-6 selects preset for current band

Directly accesses track

Delete entry or move backwards to correct error in Direct Access mode Displays Setup menu
Delete entry or move backwards to correct error in Direct Access mode Displays Setup menu Plays the first ten seconds of each track

SETUP SCAN OPEN/ CLOSE

Opens/closes the TFT monitor
UV9 USING THE TFT MONITOR

Open/Close TFT Monitor

Open TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (31) on the remote control to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (31) on the remote control to load the display panel back into the compartment.

Aspect Ratio

Press the DISP button (10) on the remote control or WIDE button (4) on the monitor to adjust the aspect ratio as follows: FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display.

Parking Brake Inhibit

When the pink "Parking" wire is connected to the vehicle Parking Brake circuit, the front TFT monitor will display video when the Parking Brake is engaged. (When the pink wire is grounded via the Parking Brake circuit, video will be displayed.)
Monitor Movement Mechanism
If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor: Table 3: Monitor Protective Measures
Obstruction Self Protection OPEN Button Pressed Power Reconnected

TFT Monitor Auto Open

If TFT Auto Open is on when the unit is turned on, the monitor automatically moves to the viewing position. If TFT Auto Open is off when the unit is turned on, press the OPEN button (1) or ( ) button (31) on the remote control to move the monitor into the viewing position. If TFT Auto Open is set to Manual, the TFT will not close when the key is turned off.

Image/Display Settings

Table 2 shows the video output mode for each playing source. Table 2: Video Output Modes
Monitor loading out horizontally Monitor loading in horizontally Monitor loading out vertically Monitor loading in vertically
Monitor is automatically loaded into unit Unit stops at obstruction point Unit stops at obstruction point Unit stops at obstruction point

Monitor fully extended horizontally Monitor fully extended horizontally Monitor swivels back to the unit Monitor swivels back to the unit
Monitor is automatically loaded into unit Monitor is automatically loaded into unit Monitor swivels back to the unit Monitor swivels back to the unit
Monitor Tilt Angle Adjustment
A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods: Step by Step Angle Adjustment Press the ( ) or ( ) button on the remote control to adjust the tilt angle of the screen one step at a time. Press the TILT - (5) or TILT+ button (6) on the monitor to adjust the tilt angle of the screen one step at a time. Continuous Angle Adjustment Press and hold the ( ) or ( ) button on the remote control to adjust the tilt angle in a continuous motion. Press and hold the TILT - (5) or TILT+ button (6) on the monitor to adjust the tilt angle in a continuous motion.

Playing Source

AM/FM TUNER DVD AUX IN

Video Output Modes

RGB Mode RGB Mode CVBS Mode
*CVBS Composite Video Baseband Signal Parameter Adjustment Procedure To adjust monitor display settings, perform the floowing steps: 1. Enter Picture Quality Setting Mode: Press the PIC button (22) on the remote control or monitor (2). Select Item to Set: Press the rotary encoder (11) on the control panel to select BRIGHT, CONTRAST, or COLOR. Set Parameters: Press the VOL +/ buttons (13, 14) on the remote or turn the rotary encoder (11) on the control panel to adjust the selected parameter. Exit Picture Quality Setting Mode: Press the PIC button (22) on the remote control or monitor (2).
After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (1) or disconnecting and reconnecting the power.
UV9 OPERATING INSTRUCTIONS

Power On / Off

Press the /SRC button (10) on the unit (or the button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. Touch the DISC, RADIO, USB, NAVI, AUX or CAMERA button to select the corresponding source. External Devices External peripheral devices, including a game console, camcorder, navigation unit, iPod, Zune, etc. can be connected to this unit via RCA output using an A/V Media Adapter Cable (not included). speaker icon and level indication is displayed on the screen. The unit will beep to confirm your turn-on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer. Press the rotary encoder (11) on the front panel to display the audio menu.

SOURCE MENU

DISC RADIO USB
BASS MID TREBLE SUB FAD BAL
-14 to +14 -14 to +14 -14 to +14 -14 to 0 Grid Grid
NOTE: The EQ mode will automatically change to USER when individual audio functions are adjusted.
The Audio menu will automatically exit after a few seconds of inactivity. To exit quickly, touch the top left corner of the screen or press and hold the rotary encoder (11).

System Reset

To correct a system halt or other [RESET] Button illegal operation, use the tip of a pen to press the reset button (12) located on the front bottom-right corner of the unit. After a system reset, the unit restores all factory default settings. NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete.
Steering Wheel Control (SWC)
The UV9 is compatible with the PAC (Pacific Accessory Corporation) steering wheel control adapter SWI-PS. A 3.5mm female connector (labeled SWC Interface) on the back of the head unit allows connectivity to the PAC adapter. Please refer to the instructions included with the PAC adapter for detailed installation information. SWC Functions The following controls are available for most vehicles: 1. 2. 3. 4. 5. 6. 7. 8. 9. Vol Down Vol Up Mute Seek Down / Previous Track / ** Preset Down Seek Up / Next Track / ** Preset Up SRC (Source) ** Select ** Select Band
** If additional steering wheel control buttons are available on the vehicle, function 7 / 8 may be assigned the "Select" feature. This feature / function may not be available on some vehicles. Select Operation If "Select" (function 7 or 8) is held down and function 4 is pressed momentarily, Preset Up will be selected. If "Select" (function 7 or 8) is held down and function 5 is pressed momentarily, Preset Down will be selected.

UV9 SETUP MENU

To access system settings, press the SETUP button (29) on the remote control or touch the button on the screen to enter the SETUP menu. The GENERAL sub-menu appears highlighted in blue. 4. Use the touchscreen or press the >/|| button (16) on the remote control to confirm setup.

Setting

Options

Function

When turned on, an audible beep tone confirms each function selection. No beep sounds.
General Sub-menu Features

Clock Mode

12Hr 24Hr
Clock displays 12 hour time using AM and PM. Clock displays 24 hour time up to 23:59. Clock appears in the top right corner of the screen and on the LCD screen during certain operations. NOTE: The AM/PM indication will change as you continue to adjust the hour past 12.

AM Frequency Spacing - 10kHz AM Frequency Band 530kHz~1720kHz FM Frequency Spacing - 200kHz FM Frequency Band 87.5MHz~107.9MHz AM Frequency Spacing - 10kHz AM Frequency Band 530kHz~1720kHz FM Frequency Spacing - 100kHz FM Frequency Band 87.5MHz~108.0MHz AM Frequency Spacing - 9kHz AM Frequency Band 531kHz~1620kHz FM Frequency Spacing - 100kHz FM Frequency Band 87.5MHz~108.0MHz AM Frequency Spacing - 9kHz AM Frequency Band 522kHz~1620kHz FM Frequency Spacing - 100kHz FM Frequency Band 87.5MHz~108.0MHz AM Frequency Spacing - 5kHz AM Frequency Band 520kHz~1600kHz FM Frequency Spacing - 100kHz FM Frequency Band 87.5MHz~108.0MHz AM Frequency Spacing - 9kHz AM Frequency Band 522kHz~1620kHz FM Frequency Spacing - 50kHz FM Frequency Band 87.5MHz~108.0MHz AM Frequency Spacing - 9kHz AM Frequency Band 531kHz~1602kHz FM Frequency Spacing - 200kHz FM Frequency Band 88.1MHz~107.9MHz

SETUP MENU

DEMO Rating Hardware P.VOL TS Cal General Language Audio

12Hr 04 : 31 AM USA On

Language Sub-menu Features If a DVD supports more than 1 Subtitle or Audio language, all the languages are available for selection during playback. If the selected language is not supported by the DVD, then the default language is used.

(HH:MM)

Clock Mode Clock Tuner Region Beep
OSD DVD Audio DVD Subtitle

English English English

On Screen Display appears in English. DVD Audio is heard in English when the option is available. DVD subtitles automatically appear in English when available. DVD subtitles appear according to the default subtitle language specified on the disc. DVD subtitles do not appear automatically. DVD menu (if applicable) is displayed in English.

Tuner Region

Accessing Menu Items
Touch the sub-menu name, press the <<, >>, |<<, or >>| direction buttons (20, 12, 15, 17) on the remote control to select a sub-menu (Language, Audio, RDS, etc.).

S.Amer1

DIRECTION BUTTONS

Arabia

Off Disc Menu English
S. Amer2 The features available for adjustment under the highlighted sub-menu option will appear in the center of the screen.

Adjusting a Feature

1. 2. Use the touchscreen to select the feature to be adjusted. Enter the option field for the feature you want to adjust by using the touchscreen or pressing the >/|| button (16) on the remote control. A submenu appears in a second row with the selected option highlighted in blue. Select a new value by using the touchscreen or pressing the >> or << buttons (12, 20) on the remote control.

Europe

Audio Sub-menu Features

Setting Function

Employ the Dynamic Range Control for better playback for low volumes. Turn bass boost on/off Turn the subwoofer on/off. Selecting a crossover frequency sets a cut-off frequency of the subwoofer's LPF (lowpass filter). Rating

1. Kid Safe 2. G 3. PG 4. PG-13 5. PG-R 6. R 7. NC-17 8. Adult
Select the appropriate rating level for the intended audience. You may override higher ratings by using your password.
Video Input (Input circuitry autodetects the video signal from the Aux In source).

NTSC PAL Auto

The color signals are output in the standard NTSC format. The color signals are output in the standard PAL format. The color signal output is switched automatically based on the current video input signal - NTSC or PAL.

Off On

Loudness Subwoofer Sub Filter
Off On Off On 80Hz 100Hz 120Hz

Load Factory

Select Reset to restore the factory default settings for the Rating system only.
If the monitor is in display mode, the monitor automatically switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor return to its original input mode. P.VOL Sub-menu Features
Demo Sub-Menu Features You can stop/run demonstration mode or turn Demo Auto Run on/off by chooing the Demo option from the SETUP MENU. When "Demo Auto Run" is Off, you can select "Demo Mode > Run" to start Demo Mode. Demo Mode scrolls through the various source screens, simulating activity on the display. Demo Mode is discreetly displayed in yellow text (below the clock), to indicate the unit is in Demo Mode. To stop Demo Mode, press the upper-left quadrant of the TFT (Source select). When Demo Auto Run is On, the unit will automatically display Demo Mode when powered on. Rating Sub-menu Features The DVD system has a built-in parental lock feature to prevent unauthorized persons from viewing restricted disc content. By default, the rating system is unlocked. Once setup, the parental lock is released only by entering the correct password. Once the password is entered, rating is available for setup.
To reset the password, access the RATING menu and enter the current password. Once the correct password is entered, you can access the Password field and enter a new one. NOTE: Record the password and keep it in a safe place for future reference. The rating for each disc is marked on the disc, disc packing, or documentation. If the rating is not available on the disc, the parental lock feature is unavailable. Some discs restrict only portions of the disc and the appropriate content will play. For details, please refer to the disc description. Hardware Sub-menu Features If the rear-view video camera is connected, the unit is on, and the TFT monitor is retracted inside the unit, the TFT monitor automatically moves into the viewing position and Camera mode is selected upon shifting into REVERSE gear. When shifting into DRIVE gear, the TFT monitor is retracted back inside unit.

Source

Radio Disc USB Aux In Navi
Choose a source for which you would like to increase the relative volume (LEVEL).

P1 P2 P3 P4 P5 P6

87.5 90.1 98.1 106.1 107.9 102.9

Seek Tuning

To seek the next higher station: Touch the >>| button on screen. Press the >>| button (17) on remote control. Touch the |<< button on screen. Press the |<< button (15) on the remote control. 3.

Preset: _

Touch the preset number in which you would like to store the current station (or touch Exit to cancel and close the menu). The preset number and station appears highlighted.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Current radio band indicator Radio frequency indicator Clock Stereo broadcasting indicator Strong Local signal broadcasting indicator Preset radio stations: Touch to recall preset stations Information about the current function Touch for quick access to Equalizer level settings Touch to access the direct entry screen Current preset station indicator |<<: Touch to seek backward >>|: Touch to seek forward <<: Touch to tune backward one step >>: Touch to tune forward one step BAND: Touch to change between AM/FM bands AS: Touch to automatically store stations Touch to view the SOURCE MENU and select a new playback source 18. MEM: View screen used to enter current channel into preset memory 19. : Touch to view the SETUP menu 20. PS (Preview Scan): Touch to scan all stations available, stopping for 5 seconds at each and continuing until a station is selected
To seek the next lower station:

Manual Tuning

To increase or decrease the tuning frequency one step: Touch the >> or << buttons on screen. Press the >> or << buttons (12, 20) on the remote control.

Direct Tuning

To enter a radio station directly, touch the button or press the GOTO button (19) on the remote control to display the direct entry menu.
Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (6) to select the corresponding stored station.

FM: _ _ _. _ MHz

3 Exit 6 9
Auto Store/Preview Scan (AS/PS)
Auto Store (AS) To select six strong stations and store them in the current band: 1. 2. Select a band (if needed). Press the AS button (3) on the control panel or touch AS (16) on the screen for 2 seconds to activate the Auto Store function.

CD Player User Interface

The on-screen indicators and touch key areas for CD playback are outlined below.

CD T: 1/10

00:00:23
Repeat Playback Touch the button on screen or press the REPT button (7) on the remote control to alter repeat mode according to the following: DVD: Repeat Chapter, Repeat Title, Repeat Off CD-DA: Repeat Single, Repeat Off CD-R/RW: Repeat Single, Repeat Off DVD-R/RW: Repeat Single, Repeat Off
Enter the desired track using the on-screen number pad. Press the enter button (arrow) to tune to the selected station. To exit the screen without changing the station, touch Exit. To clear your entry and start over, touch Clear.
Track Track Track Track Track Track
Track Scan Select (CD-DA discs only)
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Current track and total number of tracks on disc Elapsed playing time Current time Track titles Disc title /||: Touch to play/pause disc playback : Touch to stop disc playback >>|: Touch to move to next track |<<: Touch to move to previous track >>: Touch to fast forward current track <<: Touch to rewind current track Touch to activate/deactivate Repeat play mode Touch to activate/deactivate Random mode
During disc play, press the SCAN button (30) on the remote control to play the first 10 seconds of each track. When a desired track is reached, press the SCAN button again to cancel the function and play the selected track. Random Play Select While disc play is stopped, touch the button on screen to play the tracks on the disc in a random, shuffled order. Touch the (RDM) button again to cancel Random Play mode. NOTE: CD-R and CD-RW will not play unless the recording session is finalized. Fast Forward Touch the >> button on screen or press the >> button (12) on the remote control to fast forward. Keep pressing and

UV9 MP3/WMA OPERATION

Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. For example, a medium with the following folder/file hierarchy is subject to Folder Search, File Search or Folder Select, as shown below. 3. Insert the USB device into the USB connector. The unit will read the audio/video files on the USB device automatically.
Media and File Requirements
This player allows you to play back MP3 and WMA files recorded onto CD-R/RWs, DVD+R/RWs, and DVD-R/RWs. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent illegal disc operation. Up to 1500 songs/files can be burned onto a disc for a MEGA DVD music mix. Do not exceed this number of songs/files or disc readability problems may occur. MP3 Format Compatibility The file naming formats listed below are compatible with this unit: ISO 9660 file name: 12 characters, file extension: 3 characters ISO 9660 file name: 31 characters, file extension: 3 characters Joliet 64 characters

UV9 CARACTERISTIQUES

DVD/CD Player Compatible Disc Media : DVD + R / RW (Single and Dual Layer) and CD-R / RW Compatible Media Formats : CD-DA, MP3, WMA, VCD, SVCD, Xvid, AVI, MPEG1 / 2 Rapport signal au bruit : >95dBA Gamme dynamique : >95dB Rponse en frquence : 20Hz to 20 kHz, -3dB Sparation des chanes : > 60dB @ 1 kHz Adaptateur D/A : Haute performance 24-bit / 192 kHz taux d'chantillonnage, Multi-Bit Sigma-Delta Modulator Video Format : NTSC, PAL (auto-detection) Sortie : 1Vp-p (75-ohm) Entre : 1Vp-p (75-ohm) FM Tuner Gamme de syntonisation : 87.5MHz - 107.9MHz Sensibilit mono (-30dB) : 9dBf Sensibilit en sourdine (-50dB) : 15dBf Slectionnabilit alternative de canal : 70dB Rapport signal au bruit @ 1 kHz : 58dB Rejet d'Image : 80dB Sparation stro @ 1 kHz : >30dB Rponse en frquence : 30Hz - 15 kHz, -3d AM Tuner Gamme de syntonisation : 530 kHz - 1720 kHz Sensibilit (-20dB) : 15uV Rapport signal au bruit @ 1 kHz : 50dB Rejet de l'image : 60dB Rponse en frquence : 50Hz - 2 kHz, -3dB Moniteur Taille de l'cran : 7.0" (Diagonalement), 16:9 Ecran large, 6.06" (154.1mm) W X 3.42" (87mm) H Type d'cran : TFT Affichage aux cristaux liquides LCD matrice active Rsolution : 336,960 sous pixels, 1440 (W) X 234 (H) Gnral Impdance d'entre auxiliaire : 10k Alimentation : 11 to 16VDC, terre ngative Antenne de puissance (Bleu) : 500mA max, protection limite actuelle Amplificateur distance (Bleu/Blanc) : 500mA max, protection limite actuelle Temprature d'opration : -20C ~ 65C Fusible : de type 15-amp, mini ATM DIN chassis dimensions : 7" X 7" X 2" (178mm x 178mm x 50mm) Classement Puissance CEA
Sortie puissance : 13 Watts RMS x 4 cannaux dans 4-Ohms @ < 1% THD+N Rapport signal au bruit : 70dBA sous rfrence (Rfrence 1 Watt, 4-Ohms) Rponse en frquence : 20 Hz - 20 kHz, -3dB. (Entre Auxiliaire utilise comme entre de rfrence) Voltage d'alimentation de rfrence : 14.4VDC *Caractristiques sont susceptibles de changer sans avis pralable.

Limited Warranty

CD or Multimedia Radios/Headunits
Audiovox Electronics Corporation (the Company) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800323-4815 with any questions. Who is covered? The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or Canada. This warranty is not transferable or assignable. Proof of purchase is required in the form of an original sales receipt. What is covered? The Company warrants that should this product or any part thereof, under normal use, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with a new or reconditioned product (at the Company's option) without charge for parts and repair labor. What is not covered? This Warranty does not cover the following: Damage incurred during shipping or transporting the product to the Company or a service center Elimination of car static or motor noise Defects in cosmetic, decorative or non-operative structural parts Correction of antenna problems Costs incurred for installation, removal or reinstallation of the product Consequential damage to compact discs, USB devices, digital media cards, accessories or vehicle electrical systems Damage caused by improper installation, mishandling, misuse, neglect, accident, blown fuse, battery leakage, theft or improper storage Products whose factory serial number/bar code label(s) or markings have been removed or defaced Damage resulting from moisture, humidity, excessive temperature, extreme environmental conditions or external natural causes Please review the Care and Maintenance section of your Installation and Operation Manual for additional information regarding the proper use of your product.

Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensen.com 2008 Audiovox Ver. 073008 Printed in China