Film Data Sheet Spectra Grid Integral Color Print Film

Description

IFA?JH=
General-purpose, high-speed, medium-contrast, integral film for high definition instant color prints with grid lines. It is balanced for daylight and electronic flash exposure.

Key Applications

GridFilm

Film Speed

ISO 640/DIN 29
Healthcare documentation Medical imaging (clinical documentation) Law enforcement (domestic violence, child abuse, others) Jewelry documentation Manufacturing (ISO 9000 documentation) Other applications where measurement using grid lines is important

Format

4 x 41/8 in. (10.2 x 10.5 cm)

Compatible Hardware

Image Area
35/8 x 27/8 in. (9.2 x 7.3 cm)

Finish

Glossy

Exposures per Unit

10 exposures per pack
Spectra AF, Spectra 2, Spectra Pro Spectra Law Enforcement Kit Jewelry Pro HealthCam ProCam Image, Image 2, Image Elite Minolta Pro Macro 5 SLR

Special Treatment

Development Time

2 minutes approximately

Alternative product

T-990 (no grid lines)

Caution
This film uses a small amount of caustic paste. If any paste appears, avoid contact with skin, eyes and mouth and keep away from children and animals. If you get some paste on your skin, wipe it off immediately, then wash with water to avoid an alkali burn. If eye contact occurs, quickly wash the area with plenty of water and see a doctor. Do not cut or take apart pictures or battery. Do not burn battery or allow metal to touch terminals.

Limited Warranty

See information on the film box. Polaroid, Spectra, GridFilm, Jewelry Pro, HealthCam, ProCam, Image, and Polaroid Macro 5 SLR are trademarks of Polaroid Corporation, Waltham, MA 02451 USA. All other product names may be the property of their respective owners.
Film Data Sheet Technical Data

Spectra Film Family

The information in this data sheet represents the typical performance of Polaroids Spectra film family. However, there may be some variation between film lots.
Characteristic H&D curve for normal development
3 H&D Curves @ 70oF/21oC Blue Green
Recommended speed: ISO/DIN 640/290 Recommended processing time and temperature: Approximately 3 minutes at 700F/210C Balance: Daylight and electronic flash (5500oK) Contrast: Medium Resolution (1000:1): 7-10 line pairs/mm
Sample Density -3 -2 -1 0

Relative Log Exposure

D-Max: The density value for the films darkest black. D-Min: The lowest density value that a film exhibits. In prints, the whiteness of the brightest highlight, relative to the unprocessed print. Slope: The positive ratio of the log E increments of the straight line region of the curve, as determined by the 1/4-3/4 increment method. The slope of an H&D curve indicates the overall contrast of a film: low contrast slopes less than 1.10; medium contrast slopes from 1.10 to 1.70; high contrast slopes greater than 1.70.

Sample Density

Characteristic H&D curve for cold development
Characteristic H&D curve for hot development
H&D Curves @ 95 oF/35 oC

Blue Green Red

H&D Curves @ 55 oF/18 oC

-3 -2 --3 -2 -1 0

Reciprocity law failure A wide range of shutter speeds can be used without loss of film speed or requirements for color filtration. For longer exposure times, some exposure compensation and filtration is suggested. Reciprocity The ability of the film to respond in a constant manner to a constant exposure (light intensity x time). Reciprocity failure occurs during very long or very short exposures, requiring the photographer to increase exposure.

Reciprocity Law Failure

Blue 1.8 1.6 Green Red
1.4 1.2 1.0.8.6.4.2 0.0001".001".01".1" 1" 10" 100"

Exposure Time (seconds)

Modulation Transfer Function

Modulation

0.1.2.3.5
Spatial Frequency (lp/mm)

Spectral Sensitivity

Blue 1000 Green Red

Wavelength (nm)

Spectral Sensitivity: Shows the equivalent energy needed at each wavelength in order to activate the emulsion so that it produces a neutral density of.75.