SAVE THESE INSTRUCTIONS

Special cord set instructions
a. A short power supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a long cord. Your IMPRESSA has a 3-pin grounded plug. b. Longer extension cords are available and may be used if care is exercised in their use. c. If an extension cord is used, 1. the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and 2. if the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord, and 3. the longer cord shall be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children of tripped over. Z Z Z As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way or attempt to defeat this safety feature.

Warning

To reduce the risk of fire or electric shock, do not remove any service covers. No user serviceable parts inside. Repair should be done by authorized personnel only. This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by an authorized service representative: Z Do not immerse base in water or try to disassemble. Z To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside. Repair should be done by authorized service personnel only. Z Check voltage to be sure that the voltage indicated on the name plate agreees with your voltage. Z Never use warm or hot water to fill the water container! Use cold water only.

Caution

Z Z NEVER DO (or you will void your warranty protection): Z
Keep your hands and the cord away from hot parts of the appliance during operation. Never clean with scouring powders or hard implements. Never fill instant coffee, chocolate mix etc. into the grinder or ground coffee funnel (grinder by-pass). It will damage the functioning of the brewing chamber. Never fill sugar coated coffee beans into the bean hopper. In case of doubt, call your dealer. Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other than roasted coffee beans). Never do anything with the machine which is not described in the Users Manual. In case of doubt, call your dealer.

Control elements

Figure: IMPRESSA J9 One Touch Chrome
Bean container cover Water tank cover Bean container with aroma preservation cover Water tank Height- and width-adjustable coffee spout Coffee grounds container Drip tray Cup platform

Filler funnel for preground coffee Grinder adjustment switch Storage compartment cover Storage compartment with measuring spoon for preground coffee, hot-water nozzle and long spout for cappuccino frother Connector System for different cappuccino frothers Professional Cappuccino Frother (with short spout) Power switch and mains cable (side of machine)

1 Q 2 g 3 c

On/Off button Rotary Switch Maintenance button

4 u i o m z q p

Display Ristretto button Espresso button Coffee button Hot Water button Milk button Latte Macchiato button Cappuccino button
The Connector System permits the use of different cappuccino frothers. These are available from stockists. Professional Cappuccino Frother Cappuccino Latte macchiato Hot milk Milk foam Easy Cappuccino Frother Cappuccino Milk foam

Important information

Proper use
The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. Keep these instructions for use close to the machine and pass them on to the next user.

For your safety

Please carefully read and observe the important safety information set out below. To avoid danger of potentially fatal electric shock: Never use a machine which is damaged or has a defective mains cable. In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged, it must be repaired either directly by JURA or by an authorised JURA service centre. Make sure that the IMPRESSA and the mains cable are not located close to hot surfaces. Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges. Never open and repair the machine yourself. Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.

U U U U U U

There is a risk of scalds or burns on the spouts and the cappuccino frother. Place the machine out of the reach of children. Do not touch any hot parts. Use the handles provided. Ensure that the cappuccino frother is correctly fitted and clean. If incorrectly fitted or if they become blocked, the cappuccino frother or its parts might come off.

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire: Never allow the mains cable to loosely hang down. The mains cable could pose a tripping hazard or become damaged. Protect the IMPRESSA from environmental influences such as rain, frost and direct sunlight. Do not immerse the IMPRESSA, cables or connections in water. Do not put the IMPRESSA or any individual parts in the dishwasher. Switch your IMPRESSA off at the power switch before any cleaning operation. Always wipe the IMPRESSA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash. Only connect the machine to the mains voltage in accordance with the information on the rating plate. The rating plate is located on the underside of your IMPRESSA. Further technical data is provided in these instructions for use (see Chapter 9 Technical data). Please only use original JURA maintenance products. Use of products that are not explicitly recommended by JURA could damage the IMPRESSA. Do not use any coffee beans treated with additives or caramelised coffee beans. Only fill the water tank with fresh, cold water. Switch the machine off at the power switch if you are going to be absent for a longer period of time.

U U U U

People, including children, who do not have the physical, sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.
Safety when handling the CLARIS Blue filter cartridge: Filter cartridges should be kept out of the reach of children. Store filter cartridges in a dry place in the sealed packaging. Protect cartridges from heat and direct sunlight. Do not use damaged cartridges. Do not open filter cartridges.

U U U U U

Preparing and using for the first time
Visit us on the Internet.

JURA on the Internet

@ You can download short operating instructions for your
machine from the JURA website (www.jura.com). You will also find interesting and up-to-date information on your IMPRESSA and on every aspect of coffee.

Setting up the machine

When setting up your IMPRESSA, please note the following: Place the IMPRESSA on a horizontal surface that is not sensitive to water. Choose a spot for your IMPRESSA which protects the machine against overheating. Ensure that the ventilation slots are not covered.

Filling the water tank

CAUTION
To enjoy the perfect cup of coffee we recommend changing the water every day. Milk, mineral water or other liquids can damage the water tank or the machine. T Only fill the water tank with fresh, cold water. T Open the water tank cover. T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the tank. T Close the water tank cover.

Filling the bean container
The bean container has an aroma preservation cover. This will ensure that your coffee beans retain their aroma for longer. Coffee beans which have been treated with additives (e.g. sugar), preground coffee or freeze-dried coffee will damage the grinder. T Only use untreated coffee beans to refill the bean container. T Open the bean container cover and remove the aroma preservation cover. T Remove any dirt or foreign objects from inside the bean container.
T Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover.

First-time use

J WARNING
If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock. T Never use a machine which is damaged or has a defective mains cable. Precondition: The water tank and bean container are full. T Insert the mains plug into a power socket. 3 T Switch on the IMPRESSA using the power switch on the right-hand side of the machine. k T Press the On/Off button to switch the IMPRESSA on. The Rotary Switch lights up. SPRACHE DEUTSCH appears on the display. g T Turn the Rotary Switch until the required language is displayed, for example LANGUAGE ENGLISH. k T Press the Rotary Switch to confirm the language. CONFIRMED appears briefly on the display to confirm the setting. FILL SYSTEM / PRESS RINSE, the Maintenance button c lights up. T Place a receptacle under the cappuccino frother. c T Press the Maintenance button. SYSTEM FILLS, the system fills up with water. The operation stops automatically and WELCOME TO JURA appears on the display.
HEATING UP PRESS RINSE, the Maintenance button c lights up.
c T Place a receptacle under the coffee spout. T Press the Maintenance button. MACHINE RINSING, the machine rinses. The operation stops automatically. COFFEE READY appears on the display. Your IMPRESSA is ready for use.
E The buttons for the products you can prepare are illuminated.
Inserting and activating the filter
Your IMPRESSA no longer has to be descaled if you are using the CLARIS Blue filter cartridge.
E Perform the inserting the filter operation without any interruptions. This will ensure that your IMPRESSA always produces its best. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears on the display. g T Turn the Rotary Switch until FILTER NO is displayed. k T Press the Rotary Switch to enter the programme item.

FILTER NO

g T Turn the Rotary Switch until FILTER YES is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display. INSERT FILTER / PRESS RINSE, the Maintenance button c lights up. T Remove the filter cartridge extension from the Welcome Pack. T Fit the filter extension on top of a CLARIS Blue filter cartridge. T Remove and empty the water tank. T Open the filter holder and insert the filter cartridge into the water tank, exerting slight pressure. T Close the filter holder. It will click into place audibly.

E After two months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the filter holder in the water tank. T Fill the water tank with fresh, cold water and reinsert the tank. T Place a receptacle (at least 500 ml) under the cappuccino frother. T Press the Maintenance button. FILTER RINSING, water flows out of the cappuccino frother.
E You can interrupt rinsing of the filter at any time by pressing
any button. Press the Maintenance button c to continue rinsing of the filter. E The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically after approximately 500 ml. The machine heats up. COFFEE READY appears on the display. The filter is activated.
Determining and adjusting the water hardness
E If you are using the CLARIS Blue filter cartridge and have activated it in programming mode, you will not be able to adjust the water hardness. The harder the water is, the more frequently the IMPRESSA needs to be descaled. It is therefore important to adjust the water hardness. The water hardness can be adjusted on a continuous scale between 1 dH and 30 dH. It can also be deactivated, which means that the IMPRESSA will not let you know when it has to be descaled.
Determining the water hardness
You can find out what the water hardness is by using the Aquadur test strip supplied as standard. T Hold the test strip briefly (for one second) under flowing water. Shake off the water. T Wait for about one minute. T You will then be able to read the degree of water hardness from the discolouration of the Aquadur test strip and the description on the packaging. You can now adjust the water hardness. Example: Proceed as follows to change the water hardness from 16dH to 25dH. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears on the display. g T Turn the Rotary Switch until HARDNESS 16dH is displayed.
Adjusting the water hardness
k T Press the Rotary Switch to enter the programme item.
g T Turn the Rotary Switch until 25dH is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.

HARDNESS 25dH

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode. COFFEE READY appears on the display.

Adjusting the grinder

You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee. If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged. T Only adjust the consistency of grind when the grinder is running. The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms. Example: Proceed as follows to change the consistency of grind during the preparation of an espresso. T Open the cover of the storage compartment. T Place a cup under the coffee spout. i T Press the Espresso button. The grinder starts up. 1 ESPRESSO and the coffee strength are displayed. T Turn the grinder adjustment switch to the desired position while the grinder is running. The espresso is prepared and the consistency of grind is adjusted. T Close the cover of the storage compartment.

i T Press the Espresso button. Preparation will now begin. The preset amount of water for espresso flows into the cup. Preparation stops automatically and ENJOY appears briefly on the display. Then COFFEE READY is displayed.
Permanently setting the amount of water for the cup size
It is easy to permanently set the amount of water for all speciality coffees, milk specialities and hot water to the cup size. Adjust the amount once as shown in the following example. Every time you prepare a drink in the future, this amount of water will be dispensed. Permanent setting of the amount of water to the cup size for all speciality coffees, milk specialities and hot water follows this model.
Example: Proceed as follows to permanently set the amount of water for one coffee. Precondition: COFFEE READY is displayed. T Place a cup under the coffee spout. o T Press and hold the Coffee button. 1COFFEE and the coffee strength is displayed. T Hold the Coffee button down until ENOUGH COFFEE? appears. T Release the Coffee button. Preparation starts and the coffee flows into the cup. T Press any button as soon as there is sufficient coffee in the cup. Preparation stops. CONFIRMED and ENJOY appear briefly on the display. The set amount of water for one coffee is permanently stored. COFFEE READY appears on the display.
E You can alter this setting at any time by repeating the above
procedure. E You can also permanently set the amounts for all speciality coffees, milk specialities and hot water in programming mode (see Chapter 4 Permanent settings in programming mode Products).

Hot water

To obtain a perfect water flow, use the hot-water nozzle. You can find the hot-water nozzle under the cover of the storage compartment. The following temperatures can be selected for preparing hot water: LOW, NORMAL, X HIGH.

J CAUTION

There is a danger of scalding from hot water splashes. T Avoid direct contact with the skin. T Carefully pull the cappuccino frother off the Connector System. T Open the cover of the storage compartment, take out the hot-water nozzle and close the cover again. T Attach the hot-water nozzle to the Connector System, rotating it slightly.
T Place a cup under the hot-water nozzle. T Press the Hot Water button. The temperature is displayed.
E By touching the Hot Water button several times (within
approximately 2 seconds) you can set the temperature to your individual preference. This setting is not saved.

WATER, hot water flows into the cup. Preparation stops automatically and COFFEE READY appears on the display.

Daily operation

When the IMPRESSA is switched on, it automatically prompts you to perform the rinse operation. Start the rinse operation by pressing the Maintenance button c. In programming mode you can change this setting so that the machine starts the switch-on rinse automatically (see Chapter 4 Permanent settings in programming mode Rinses). Precondition: Your IMPRESSA is switched on at the power switch. T Place a receptacle under the coffee spout. Q T Press the On/Off button to switch the IMPRESSA on. WELCOME TO JURA appears on the display.

Switching on

c T Press the Maintenance button. MACHINE RINSING, the machine rinses. The operation stops automatically and COFFEE READY appears on the display.

Daily maintenance

To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality, the machine requires daily maintenance. T Pull out the drip tray. T Empty the coffee grounds container and the drip tray. Rinse them with warm water. T Dry the metal contacts on the back of the drip tray. T Refit the coffee grounds container and the drip tray. T Rinse the water tank with clean water. T Dismantle and rinse the cappuccino frother (see Chapter 5 Maintenance Rinsing the cappuccino frother). T Wipe the surface of the machine with a clean, soft, damp cloth (e.g. microfibre cloth).

Switching off

When you switch your IMPRESSA off, the spouts used to prepare a speciality coffee are rinsed. T Place a receptacle under the coffee spout and another under the cappuccino frother. T Press the On/Off button. MACHINE RINSING, the spouts used to prepare a speciality coffee or milk are rinsed. The operation stops automatically and your IMPRESSA is switched off.
E When the IMPRESSA is switched off with the On/Off button,
the machine consumes less than 0.1 W of standby energy. The machine can be completely disconnected from the power supply using the power switch.

LOW, NORMAL, X HIGH

3SEC 120SEC 25ML 450ML

Permanent settings in programming mode always follow the same model. Example: Proceed as follows to change the amount of milk for a latte macchiato from 16 SEC to 20 SEC, the amount of water from 45ML to 40ML and the interval from 30SEC to 20SEC. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until PRODUCTS is displayed. k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT E Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
E To change the setting for a double product, press the corresponding button twice within two seconds. q T Press the Latte Macchiato button.

COFFEE 45ML

g T Turn the Rotary Switch until COFFEE 40ML is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.

COFFEE 40ML

g T Turn the Rotary Switch until MILK 16SEC is displayed. k T Press the Rotary Switch to enter the programme item.

MILK 16SEC

T Turn the Rotary Switch until MILK 20SEC is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.

MILK 20SEC

g T Turn the Rotary Switch until PAUSE 30 SEC is displayed. k T Press the Rotary Switch to enter the programme item.

PAUSE 30SEC

g T Turn the Rotary Switch until PAUSE 20 SEC is displayed.
k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.

PAUSE 20SEC

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.
COFFEE READY Energy-saving mode
In the programme item ECONOMY MODE you can permanently set an energy-saving mode (Energy Save Mode, E.S.M.):

SAVE NO

U All speciality coffees with and without milk as well as hot
water can be prepared without having to wait.

U Before milk preparation, the machine heats up.
SAVE YES (Energy saving of up to 40%)
U Soon after the last preparation, the IMPRESSA stops heating
up. As soon as the energy-saving temperature is reached, this is indicated in the display by the message ENERGY ON this may take several minutes. The machine must heat back up before the next preparation. U Before the preparation of coffee, hot water or milk, the machine heats up.
Example: Proceed as follows to change the energy-saving mode from SAVE YES to SAVE NO. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until ECONOMY MODE p is displayed. k T Press the Rotary Switch to enter the programme item.

SAVE YES

g T Turn the Rotary Switch until SAVE NO is displayed.
ECONOMY MODEg T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.
COFFEE READY Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after the preset time following the last action on the machine. You can set the automatic switch-off to 15 minutes or 0.hours. Example: Proceed as follows to change the automatic switch-off from 1H to 15MIN. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until OFF AFTER 1 H is displayed. k T Press the Rotary Switch to enter the programme item.

OFF AFTER 1H

g T Turn the Rotary Switch until OFF AFTER 15 MIN. is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.

OFF AFTER 15MIN.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

COFFEE READY Rinses

In the programme item RINSES you can make the following settings:

INIT RINSE MANUAL

U The switch-on rinse must be started manually.

INIT RINSE AUTO

U The switch-on rinse is started automatically.

CAPP RINSE AFTER10'

U You are prompted to perform a cappuccino rinse 10 minutes
after preparation of a milk product.

CAPP RINSE NOW

U You are prompted to perform a cappuccino rinse immediately after preparation of a milk product.
Example: Proceed as follows to make the machine prompt you to perform the cappuccino rinse immediately after preparing a milk product. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until RINSES is displayed. k T Press the Rotary Switch to enter the programme item.
g T Turn the Rotary Switch until CAPP RINSE AFTER10' is displayed. k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until CAPP RINSE NOW is displayed. k T Press the Rotary Switch to confirm the setting. CONFIRMED appears briefly on the display.
g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch.
COFFEE READY Restore factory settings
In the programme item RESET you can reset various settings to their factory settings:

PRODUCT

U The settings (amount of water, aroma, temperature etc.) for
any product can be reset individually to the factory settings. The corresponding double product is reset to the factory settings at the same time.

ALL PRODUCTS

all products are reset to the factory settings.

RESET ALL

U All customer settings are reset to the factory settings. Your
IMPRESSA then switches off.
Example: Proceed as follows to reset the values for Espresso to the factory settings. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until RESET is displayed. k T Press the Rotary Switch to enter the programme item.
i T Press the Espresso button. CONFIRMED appears briefly on the display. The settings for Espresso are reset to the factory settings.
COFFEE READY Viewing information and maintenance status
In the programme item INFORMATION you can view the following information: Number of prepared speciality coffees, milk specialities and hot water Maintenance status and number of maintenance programmes performed (cleaning, descaling, changing the filter) Number of cappuccino frother cleaning operations performed Software version
Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until INFORMATION is displayed. k T Press the Rotary Switch to enter the programme item. TOTAL, the total number of prepared speciality coffees and milk specialities is displayed. g T Turn the Rotary Switch to view additional information.
E The maintenance status can also be displayed in addition to
the number of performed maintenance programmes. The bar shows the current maintenance status. When the bar is completely filled, your IMPRESSA will request the respective maintenance programme. k T Press the Rotary Switch to exit the programme item.
COFFEE READY Unit for amount of water
You can change the unit for the amount of water from ml to oz. Example: Proceed as follows to change the unit for the amount of water from ML to OZ. Precondition: COFFEE READY is displayed. k T Press and hold the Rotary Switch until MAINTENANCE appears. g T Turn the Rotary Switch until SETTINGS ML is displayed. k T Press the Rotary Switch to enter the programme item.

Descaling the machine

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water. If the descaling agent comes into contact with the skin or eyes, this can cause irritation. T Avoid contact with the skin or eyes. T Rinse off descaling agent with clean water. Should you get any descaling agent in your eye, seek medical attention. If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water. T Use only original JURA maintenance products. If the descaling operation is interrupted, there may be damage to the machine. T Allow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. T Clean up any splashes immediately.
E The descaling programme lasts approximately 45 minutes. E JURA descaling tablets are available from stockists. E If you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale. Precondition: COFFEE READY / DECALCIFY MACHINE is displayed and the Maintenance button c lights up. c T Press the Maintenance button. DECALCIFY DURATION 45MIN. / START YES
E If you do not want to start descaling just yet, turn the Rotary Switch until START NO is displayed. Press the Rotary Switch
to exit the maintenance programme. The prompt to descale the machine remains active. c T Press the Maintenance button.
T Empty the drip tray and coffee grounds container and put them back into the machine.

SOLVENT IN TANK

T Remove and empty the water tank. T Completely dissolve the contents of one blister (three JURA descaling tablets) in a receptacle holding 500 ml of water. This may take several minutes. T Pour the solution into the empty water tank and insert it into the machine. SOLVENT IN TANK / PRESS RINSE, the Maintenance button c lights up. T Remove the cappuccino frother from the Connector System.
T Place a receptacle (at least 500 ml) under the Connector System. T Press the Maintenance button.

DECALCS

This causes water to flow out of the Connector System several times. The Maintenance button c flashes during the descaling operation. The operation stops automatically, EMPTY TRAY. T Empty the receptacle under the Connector System. T Empty the drip tray and coffee grounds container and put them back into the machine. RINSE WATER TANK / FILL WATER TANK T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold water and reinsert the tank. PRESS RINSE, the Maintenance button c lights up. T Refit the cappuccino frother. T Place a receptacle under the cappuccino frother and another under the coffee spout. T Press the Maintenance button. DECALCS, water flows out of the cappuccino frother and the coffee spout. HEATING UP, MACHINE RINSING, water flows out of the coffee spout. The operation stops automatically, EMPTY TRAY. T Empty the drip tray and coffee grounds container and put them back into the machine. Descaling is now complete. The IMPRESSA is once more ready for use.

E If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

Cleaning the bean container
Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time. Precondition: COFFEE READY / FILL BEANS is displayed. Q T Switch the machine off with the On/Off button. 3 T Switch the machine off at the power switch. T Open the bean container cover and remove the aroma preservation cover. T Clean the bean container with a soft, dry cloth. T Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover.

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time. T Remove the water tank. T If you use a CLARIS Blue filter cartridge, remove this. T Descale the tank with a mild conventional descaling agent in accordance with the manufacturer's instructions. T Rinse out the water tank thoroughly. T If you use a CLARIS Blue filter cartridge, insert this again. T Fill the water tank with fresh, cold water and reinsert the tank.

6 Display messages

Message Cause/Result The water tank is empty. You cannot prepare any products. Action T Fill the water tank (see Chapter 1 Preparing and using for the first time Filling the water tank). T Empty the coffee grounds container and the drip tray (see Chapter 3 Daily operation Daily maintenance). T Empty the drip tray. T Clean and dry the metal contacts on the back of the drip tray. T Fit the drip tray.

FILL WATER TANK

EMPTY GROUNDS
The coffee grounds container is full. You cannot prepare any coffee products, but you can prepare hot water and milk. The drip tray is full. You cannot prepare any products.

TRAY MISSING

The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any products. The IMPRESSA is prompting you to perform a rinse or continue a maintenance programme that was already started. The bean container is empty. You cannot prepare any coffee products, but you can prepare hot water and milk. The IMPRESSA requests a cappuccino rinse. The IMPRESSA is prompting you to clean it.

PRESS RINSE

T Press the Maintenance button to start the rinse or to continue the maintenance programme. T Fill the bean container (see Chapter 1 Preparing and using for the first time Filling the bean container). T Press the Maintenance button to start the cappuccino rinse. T Perform cleaning (see Chapter 5 Maintenance Cleaning the machine).

FILL BEANS

COFFEE READY / RINSE CAPPUCCINO COFFEE READY / CLEAN MACHINE or COFFEE READY / CLEAN NOW

Message

Cause/Result The IMPRESSA is prompting you to descale it.
Action T Perform descaling (see Chapter 5 Maintenance Descaling the machine ). T Replace the CLARIS Blue filter cartridge (see Chapter 5 Maintenance Changing the filter).
COFFEE READY / DECALCIFY MACHINE or COFFEE READY / DECALCIFY NOW COFFEE READY / CHANGE FILTER or COFFEE READY / CHANGE NOW NOT ENOUGH PRE-GROUND
The filter cartridge no longer works.
There is insufficient preground T The next time you prepare a coffee in the machine; the beverage, add more preIMPRESSA stops the operation. ground coffee (see Chapter 2 Preparation Preground coffee).

Troubleshooting

Cause/Result The cappuccino frother is dirty. Action T Rinse and clean the cappuccino frother (see Chapter 5 Maintenance Rinsing the cappuccino frother). T Set the grinder to a coarser setting or use coarser preground coffee (see Chapter 1 Preparing and using for the first time Adjusting the grinder). T Deactivate the filter cartridge in programming mode. T Clean the bean container (see Chapter 5 Maintenance Cleaning the bean container). T Clean and dry the metal contacts on the back of the drip tray. T Descale the water tank (see Chapter 5 Maintenance Descaling the water tank). T Contact customer support in your country (see Chapter 11 JURA contact details / Legal information). T Warm the machine at room temperature.
Problem Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother. Coffee only comes out in drips when it is being prepared.
Coffee or preground coffee has been ground too finely and is blocking the system.
Water hardness cannot be adjusted.
The CLARIS Blue filter cartridge is activated. The bean monitor is dirty.