-J04758

REV. 2008-08-26

ROAD KING FRONT END LOWERING KIT

GENERAL

Kit Number
46875-09 The rider's safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. This kit is not designed to be used with Sidecar installed. Any attempt to use this front suspension kit with sidecar can adversly affect stability and handling. (00430b)

Models

For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required

Kit Contents

See Figure 6 and Table 2.

is00154

This Front End Lowering Kit cannot be used independently. It must be used with an appropriate Low Rear Suspension Kit or handling and cornering can be affected, which could distract the rider, causing loss of control and death or serious injury. (00429b) Proper installation of this kit requires, except FLHX, installation of an FL Profile Low Rear Suspension Kit (54635-09). Proper installation of this kit also requires the following special tools: Fork Tube Holder (HD-41177), Fork Seal/Bushing Tool (HD-34634) and Front Fork Oil Level Gauge (HD-59000B). Proper installation of this kit may also require the replacement of the following parts: Table 1. Replacement Parts Item (Quantity) O-ring (2) Quad ring seal (2) Wear ring (2) Slider bushing (2) Fork oil seal (2) Screw with copper crush washer, 6 mm (2) Harley-Davdison Fork oil Part Number 45845-77 45733-48 45859-77A 45940-84 45875-84A 45405-75A 99884-80
1. Vise grip 2. Rubber pad 3. Plastic knob Figure 1. Fork Tube Holder (HD-41177)

REMOVAL

1. 2. Refer to the appropriate service manual and remove the front fender, wheel and brakes. Refer to the appropriate service manual and remove the front forks.

1 of 6

is00158
Slowly remove fork tube plug (C) from fork tube (H). Be aware that fork tube plug is under spring-pressure, so have a firm grasp on plug as the last thread is turned.
Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) Figure 2. Front Fork Oil Level Gauge (HD-59000B)

is00159

Remove the fork spring (1) from the fork tube. Remove fork assembly from fork tube holder. Turn fork upside down and drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. Install fork spring back into fork tube. Put a shop rag on the floor. Turn the fork assembly upside down and press the end of the spring against the rag. Compress the spring and remove the screw (S) from end of fork slider (T). Use air impact wrench for best results. Discard screw (S) and copper crush washer (R).

10. Remove fork spring (1) and damper tube (2) from fork tube. Discard fork spring. 11. Remove and save rebound spring (V) from damper tube. Discard damper tube. Figure 3. Remove Excess Fork Oil 12. Using pick tool, remove retaining clip (I) between fork slider (T) and fork tube (H). Do not expand or stretch retaining clip to remove from fork tube or clip may be damaged. NOTE To overcome any resistance, use the fork tube as a slide hammer: Push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 13. Remove fork tube from fork slider. 14. Slide fork oil seal (J), slider spacer (K) and slider bushing (M) off end of fork tube. Discard fork oil seal and slider bushing. 15. Gently pry at split line to expand fork tube bushing (L), and then remove from groove at end of fork tube. Discard fork tube bushing. 16. Remove the lower stop (U) from the fork slider.
Incorrect amount of fork oil can adversely affect handling and lead to loss of vehicle control, which could result in death or serious injury. (00298a)

INSTALLATION

Right Side and Left Side Fork Disassembly
1. 2. Obtain right fork assembly removed in earlier step. See Figure 6. Remove nuts (G), lockwashers (F), flat washers (E) and axle holder (N) from studs at end of fork slider (T). See Figure 1. Install fork in Fork Tube Holder (HD-41177) as follows: a. b. Clamp end of tool (1) in vise in a horizontal position. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held.
Right Side and Left Side Fork Assembly
Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. (00421b) NOTES Clean all components and inspect for wear. Refer to Figure 6 for the following procedure. 1. Coat new fork tube bushing (45866-84, not included) ID with clean fork oil. Expand fork tube bushing at split line only so far as required to slip over end and into groove of fork tube.
Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Refer to Figure 6 for Steps 4 - 16. 4. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal (B). Save bolt but discard quad ring seal.

2 of 6

Obtain new damper tube (2). If necessary, install new wear ring (O, 45859-77A, not included) in groove at top of new damper tube. Install rebound spring (V) and install on opposite end of damper tube. With the wear ring topside, slide new damper tube (2) into fork tube, so that tube end drops through hole at bottom of fork tube (H). Install lower stop (U) at end of damper tube. Install fork slider (T) in fork tube holder. Slide fork tube into fork slider. Coat slider bushing (M) ID with clean fork oil. Slide slider bushing down fork tube. Slide slider spacer (K) down fork tube until it contacts slider bushing.
See Figure 4. Obtain the Fork Seal/Bushing Tool (HD34634) and proceed as follows: a. b. Slide the fork seal installer down the fork tube until it contacts the fork oil seal. See Figure 5. Using the tool like a slide hammer, drive fork oil seal (with slider spacer and guide bushing) down the fork tube until retaining clip groove is visible in fork slider ID. Slide the retaining clip (I) down the fork tube until it contacts the fork oil seal. Install retaining clip in the fork slider groove. Do not expand or stretch retaining clip to install on fork tube or clip may become bent or distorted.

4. 5. 6.

NOTE Place masking tape over edge of fork tube to avoid damaging lip of fork oil seal during installation. 7. Coat the new fork oil seal (J, 45875-84A, not included) ID with clean fork oil. With the lip of garter spring side facing down (toward the fork slider), slide fork oil seal (J) down fork tube until it contacts the slider spacer. Remove masking tape from edge of fork tube.

is00156

NOTE Verify the fork spring is installed with dense section of coils to the bottom. 9. Obtain new fork spring (1). Install fork spring into fork tube.
10. Remove fork assembly from fork tube holder. 11. Place a shop rag on the floor, turn fork assembly upside down and press end of spring against rag. 12. Install new screw (S) with copper crush washer (R, 4540575A, not included). Slide screw through hole at bottom of fork slider (T) and start into end of damper tube. 13. While compressing spring to prevent rotation of damper tube, tighten the screw to 11-18 ft-lbs (15-24 Nm). 14. Remove fork spring from fork tube. 15. With the fork tube topside, clamp fork slider (not the fork tube) into fork tube holder. NOTE Install the drain screw at the bottom of the fork slider, if removed. Tighten the screw to 72-96 in-lbs (8-11 Nm).

Figure 4. Fork Seal/Bushing Tool (HD-34634)

is00157

16. Pour 11.2 ounces (330 ml) of Harley-Davidson Type E Fork Oil into the fork tube. Pump fork tube until some resistance is felt then pump a few more times to remove air from system.
Figure 5. Install Fork Oil Seal

3 of 6

17. Adjust the fork oil level, so that it is 4.92 inches (125 mm) from the top of the fork tube with the fork tube compressed, the main spring removed. Proceed as follows: a. b. See Figure 2. Obtain the Front Fork Oil Level Gauge (Part Number HD-59000B). Loosen thumbscrew on metal ring and move it up or down the rod until the bottom of the ring is 4.92 inches (125 mm) from the bottom of the rod. Tighten thumbscrew. Push the handle on the cylinder all the way in. See Figure 3. Insert rod into top of fork tube until metal ring rests flat on top of fork tube. Pull handle to remove fork oil from fork tube. Observe fork oil through transparent tube to verify oil is being drawn from cylinder. Remove rod from fork tube. Push handle into cylinder to eject excess fork oil into suitable container. Dispose of waste properly. If necessary, repeat Steps 17(c) through 17(f). Level is correct when no fork oil is observed being drawn through transparent tube.
20. Install new quad ring seal (B) (45733-48, not included) onto fork cap bolt. Thread fork cap bolt (A) into fork tube plug to prevent loss of fork oil while handling. 21. Repeat steps 1-20 for other fork.

Fork Installation

1. 2. Remove fork cap bolt from front fork. Refer to the appropriate service manual and install the front forks.

c. d. e.

After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a)
Whenever a wheel is installed and before moving the motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00284a) 3. 4. Refer to the appropriate service manual and install the front fender, wheel and brakes. Pump brakes to build system pressure.
18. Install fork spring into the fork tube with the dense end down. NOTE Do NOT overtighten or O-ring damage may occur. 19. Install new O-ring (D, 45845-77, not included) onto fork tube plug (C). Thread fork tube plug into fork tube while compressing fork spring with end of fork tube plug. Tighten fork tube plug to 22-59 ft-lbs (30-79 Nm).

Test Ride

1. Test ride motorcycle to verify proper fork travel and rebound.

4 of 6

SERVICE PARTS

is04976b

A C B D 1

I O 2 V U J K M L

N R E F S G
Figure 6. Service Parts: Road King Front End Lowering Kit Table 2. Service Parts Table Item Fork spring (2) Damper tube (2) Description (Quantity) Part Number Not Sold Separately Not Sold Separately

5 of 6

Table 2. Service Parts Table Item A B C D E F G H I J K L M N O P Q R S T U V Fork cap bolt (2) Quad ring seal (2) Fork tube plug (2) O-ring (2) Washer, flat (4) Lockwasher (4) Nut (4) Fork tube (2) Retaining clip (2) Fork oil seal (2) Slider spacer (2) Bushing, fork tube (2) Bushing, slider (2) Axle holder Wear ring (2) Washer, flat (2) Plug (2) Washer, copper, crush (2) Screw, 6 mm (2) Fork slider (2) Lower stop (2) Rebound spring (2) Description (Quantity) Part Number
Items mentioned in text, but not included in kit:

6 of 6

Profile Low Front Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54564-09 Custom Sidekick Two-Up Seat (Creamator Pattern - Blue Stitch - Blue Alligator). . . . . . . . . . . . . . . . . . . . 51620-09A
NEW Wind Splitter Windshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57164-10 Mustache Engine Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49155-09A

passengeR BaCKRest

4-Point Docking Hardware Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54205-09 Sissy Bar Upright Short, Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54248-09 Passenger Backrest Pad Short, Smooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51579-05 Stealth Detachable Luggage Rack Black . . . . . . . . . . . . . . . . . . . . . . . . . . . 53566-09

audio aCCessoRies

NEW Road Tech zumo 665 GPS Navigator . . . . . . . . . . . . . . . . . . . . . . 76000014 NEW Boom! Audio iPod Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76476-10 Boom! Audio Premium Speaker Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77181-10
NEW Anarchy Wheel Mirror Chrome, 18" Front . . . . . . . . . . . . . . . . . . . . . . 55066-11 NEW Anarchy Wheel Mirror Chrome, 18" Rear . . . . . . . . . . . . . . . . . . . . . . 55067-11
Chrome Front End Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46371-08 Outer Fairing Skirt Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46559-03
NEW LED Headlamp Kit 7" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73390-10 NEW LED Passing Lamp Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73396-10 Custom Auxiliary Lighting Bracket Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69818-06 Custom Auxiliary Lamp Turn Signal Kit Clear . . . . . . . . . . . . . . . . . . . . . . 69229-04
Hand ContRoLs & gauges
Hand Grips Aileron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56425-08 Hand Levers Chrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38843-08
Air Cleaner Trim Willie G Skull . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29417-04
Billet Brake Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42638-08A Billet Heel/Toe Shift Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34535-00B Shifter Peg Streamliner (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34967-04

Extended Reach Rider Footboard Pans . . . . . . . . . . . . . . . . . . . . . . . 50409-04 Shift Linkage Smooth Bar & Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . .33884-09 Chrome Passenger Footboard Covers . . . . . . . . . . . . . . . . . . . . . . . . 50782-91 Rider Footboard Inserts Nostalgic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50187-96 Passenger Footboard Inserts Nostalgic . . . . . . . . . . . . . . . . . . . . . . . . 50190-96 Shifter Pegs Nostalgic (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34627-99 Brake Pedal Pad Nostalgic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44248-96
door County, Wi n 45 09.331' - W 87 10.259'
Hob nob Restaurant; Racine, Wi n 42 39.822' - W 87 48.564'

Road gLide Custom

Street Stalker Front Fender Primed . . . . . . . . . . . . . 59397-98 NEW Razor-Pak Luggage Sedona Orange . . . . . . 79175-10DGR NEW Saddlebag Lid Spoilers Sedona Orange . . 58606-11DGX NEW Tour-Pak Lid Spoilers Sedona Orange . . . . 53149-11DGX
NEW Agitator Wheel Contrast Chrome, 19" Front . . . 55070-11 Agitator Wheel Contrast Chrome, 18" Rear . . . . . . . . 40225-10 NEW Agitator Brake Rotors . . . . . . . . . . . 41500007 / 41500008

Road gLide uLtRa

Production Color: Brilliant Silver
Profile Low Front Suspension . . . . . . . . . . . . . . . . . . 54564-09 Premium Hand Adjustable Low Shocks . . . . . . . . . . . . 54680-10 NEW Harley Hammock Seat with Heat . . . . . . . . . . 52000004 Adjustable Rider Backrest Smooth . . . . . . . . . . . . . . 52501-09A
Chrome Front End Kit . . . . . . . . . . . . . . . . . . . . . . . . . . 46335-08
Tour-Pak Spoiler Kit Brilliant Silver . . . . . . . . . . . .53149-04BHT Saddlebag Spoiler Kit Brilliant Silver . . . . . . . . . 58606-04BHT
Production Color: Sedona Orange
Profile Low Front Suspension . . . . . . . . . . . . . . . . . . 54564-09 Profile Low Rear Shocks. . . . . . . . . . . . . . . . . . . . . . . . .54635-09 Rallyrunner Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51527-09A
Fork Sliders Black . . . . . . . . . . . . . . . . . . . . . . . . . . . 46546-03 Upper Fork Covers Black . . . . . . . . . . . . . . . . . . . . . . 45591-02
Cut through the air with the Wind Splitter Windshield and high performance Screamin Eagle intake and exhaust. Then keep it under the radar with low-profile suspension, blacked-out trim and slammed Razor-Pak luggage.

Primed. Black Cherry. Black Pearl. Candy Red Sunglo. Charcoal Slate. (09 FLTRSE3) Copper Pearl. Crimson Red Sunglo. Dark Blue Pearl. Deep Cobalt. Fire Red Pearl. Mirage Orange Pearl. Pewter Pearl. Red Hot Denim. Red Hot Sunglo. Titanium Dust. Vivid Black. Yellow Pearl.
$469.95 $649.95 $649.95 $649.95 $849.95 $649.95 $649.95 $649.95 $649.95 $649.95 $649.95 $649.95 $649.95 $649.95 $849.95 $649.95 $649.95 $449.95 $624.95
Fits 98-03 FLTR/I models.
58841-98 Primed. 58841-98DH Vivid Black.
B. NON-VENTED FAIRING LOWERS* Made from tough, lightweight vacuum-formed ABS, these fairing lowers protect the rider from the elements and direct cooling air to the engine. Lowers attach to the engine guard without interfering with rider footboards. Kit includes all necessary mounting hardware. Glove Boxes are sold separately. NOTE: All fairing lower kits are painted with a single color scheme and do not include pinstripes.
Fits 83-later FLHT (except FLHTCUTG), FLHTC, FLHX and FLHR models. (Does not fit with Mustache Engine Guard P/N 49155-05 and Front Bullet Turn Signal Kit P/N 6949205 and 69493-05.) (NOTE: Requires drilling a hole in the left side fairing lower for the engine guard filler valve on 84-87 models.)
58830-88 Primed. 58830-88DH Vivid Black. $429.95 $624.95
C. FLT AND FLHT FAIRING LOWER GLOVE BOXES Offers a convenient place to store riding gloves, sunglasses, etc. The snap-on door cover (included) is embossed with Bar & Shield logo. Available in black only.
Ultra Classic Styling 58683-89B Left Side. $169.95 Fits 04-earlier Original Equipment non-vented style FLHT Ultra Classic Fairing Lowers. 58684-89B Right Side. $169.95 Fits 04-earlier Original Equipment non-vented style FLHT Ultra Classic Fairing Lowers. 58687-89 Left Side. $169.95 Fits non-vented style FLT and FLTR Fairing Lowers. 58688-89A Right Side. $169.95 Fits non-vented style FLT and FLTR Fairing Lowers.
A. COLOR-MATCHED ROAD GLIDE NON-VENTED FAIRING LOWER KIT
B. NON-VENTED FAIRING LOWERS
C. FLT AND FLHT FAIRING LOWER GLOVE BOXES ULTRA CLASSIC STYLING

TOURING 343

Fairing Lowers and Wind Deflectors
D. FaIRING LOweR LOckING GLOve BOx DOORs seT Keyed-to-matchsecurity.Addsecuredstoragetoyourfairing lowers.ThisLockingGloveBoxDoorKitreplacestheOriginal Equipmentflexiblesnap-oncovers,andprovidesconvenient, weather-resistantstoragefordocuments,cellphones,and sunglasses.Thekitsarekeyedtomatchtoyourmotorcycle ignition,forbarrelstylekeys,foronekeyconvenience.This lockingdoorkitisanidealcompaniontotheFittedGloveBox LinerKit,P/N58714-06.Kitincludesleftandrightlockingdoor assembliesanddoorframes. 57411-08 $195.95 Fits91-laterTouringandTrikemodelsequippedwithElectra GlideUltrastylefairinglowers.Alsofitsaccessoryfairing lowers,ventedandnon-vented.DoesnotfitwithGloveBox DoorPouchP/N57400-06. e. GLOve BOx DOOR POUches Pouchesfitperfectlyonyourgloveboxdoorstoprovideconvenientstorageofsmallitemsatyourfingertips.Madeofaballisticnylonexteriorandasoft,fuzzyinteriorwithelasticsides forexpandability.Perfectforyourcellphone,digitalmedia player,toll-waypassoranyothersmallitems.Reinforced coverfeaturesanembroideredBar&Shieldlogo.Kitincludes leftandrightpouches. 57400-06 $29.95 FitsTouringandTrikemodelsequippedwithventedfairing lowers.DoesnotfitwithLockingGloveBoxDoor P/N57411-08. F. FITTeD GLOve BOx LINeR kIT Protectyourbelongingsandreducenoiseandrattlesonthe road.Soft-touchfelt-finishlinerisformedtothefairingglove boxinteriorforaperfectfit.Moldedbaseandsidesmaximize theinteriorroom,andone-piecedesignallowseasyremoval forcleaningandmaintenance. 58714-06 $29.95 FitsTouringandTrikemodelsequippedwith VentedFairingLowers. G. MID-FRaMe aIR DeFLecTOR Designedforseveredutyandextremetemperatureapplications.Theseblackdeflectorsattachtotheframebelowthe seat,anddirectheatawayfromtheridertoimprovecomfort. 58002-09 $74.95 Fits09-laterTouringandTrikemodels.OriginalEquipment onFLHTCU,FLHTCUTG,FLTRUandFLHTKmodels. 58022-07a $74.95 Fits01-08Touringmodels.Doesnotfit01-07models equippedwithAdjustableRiderBackrests. h. FLTR wIND DeFLecTOR kIT Easytoinstall,thesesnap-fitWindDeflectorsreduceandredirecttheairflowthatrisesbetweenthefairingandforktubes. Theresultingreductioninupdraftcandramaticallyreduce buffetingformanyriders.Stockon11CVORoadGlide. 57000063 $29.95 Fits98-laterFLTRandFLTRUmodels.(Willnotfitmodels equippedwiththeFuelTankretrofitmountingkit.)

d. cVO ROad kING FlaMed leaTHeR TOUR-Pak lUGGaGe
NOTE:SomeHarley-Davidsonluggageismadeofleather. FineleathersorothernaturalmaterialsWILLgaincharacter, suchaswrinklesorwear,withage.Thisisnormal.Afine,aged patinaandcharacterwrinklesareasignoftheextremelyhigh qualitymaterialsusedtoconstructyourluggage.The appearanceofscarsormarksontheleatherarearesultof usingnaturalleatherpanelsandshouldnotbethoughtofas animperfection.PleaseuseHarley-DavidsonLeatherDressing P/N98261-91Vtoprotectyourinvestment.
e. PReMIUM leaTHeR TOUR-Pak lUGGaGe (sHOWN WITH TOUR-Pak INsTallaTION kIT)

TOURING 373

F. LEATHER TOUR-PAK LOCK SET Designed to discourage grab-and-run theft, this Lock Set provides a level of security that leather straps alone cant match. The complete kit includes external locking pushbutton latch release, locking mechanism, release cable, two keys, steel Tour-Pak lid mounting plate, and all required installation hardware. Special order keyed-to-match lock sets are available for models with barrel-type keys. Contact your Dealer with your vehicle key code.
54360-05 $169.95 Fits models equipped with Leather or Synthetic Leather TourPak Luggage (except P/N 79189-06).
G. ROAD KING SADDLEBAG LOCK SET Add theft deterrence to your Road King rigid leather saddlebags. Special order keyed-to-match lock set available. Contact your Dealer with your vehicle key code. Kit includes two keys.
46316-04 Fits 98-later Road King Classic models. 46287-04 Fits 04-07 Road King Custom models. $239.95 $69.95
F. LEATHER TOUR-PAK LOCK SET
G. ROAD KING SADDLEBAG LOCK SET
H. ROAD KING CLASSIC SADDLEBAG TRIM Chrome-plated, extruded and machined aluminum trim for saddlebag lid. Saddlebag trim complements the details of the Road King fuel console. Includes four extruded trim spears and polished, stainless steel button head mounting hardware. Designed for use on the FLHRC leather saddlebags. Also looks great on Color-Matched hard bags.
53767-98 $129.95 Fits 98-later Road King Classic and 93-later models with H-D Color-Matched Hard Saddlebags.
I. UNIVERSAL SADDLEBAG LOCK KIT Keep the contents of your existing soft-sided saddlebags safe from the grab-and-go thief. This unique kit features two extra small barrel locks that can replace existing saddlebag snaps to perform double duty as locks or as snaps when you dont need to lock your bags. Can be keyed to match your barrel style ignition key. Sold in pairs.
Fits most soft-sided leather and vinyl saddlebags.

90300003 90300017

Keyed To Match. Random Key Code.

$59.95 $49.95

J. SADDLEBAG HINGE STOP KIT Required for installation of Docking Hardware Kits on 09-later FLHRC models, and Luggage Rack P/N 53011-98 on 94-08 FLHRC and 07-08 FLHRSE models.

D. COMFORT PROFILE REAR SADDLEBAG GUARD KIT* The unique profile of these chrome-plated Rear Saddlebag Guards gives your passenger more leg room. A perfect replacement for the Original Equipment saddlebag guards.
49179-09 $179.95 Fits 09-later Touring models (except FLHTC, FLHTCU, FLHTCUSE4/5/6 and Trike). FLHX, FLHXSE/2, FLTR, FLTRX, FLTRU, and FLTRSE3 models require separate purchase of Saddlebag Supports P/N 49194-09A, 90781-09A and Nut P/N 7531 (Qty 2). FLHX, FLHXSE/2, FLTR, FLTRX and FLTRU models require separate purchase of Antenna Mounting Bracket P/N 76516-09. FLHRC requires separate purchase of Reflector P/N 59370-98 and 59371-98. 49087-01 $179.95 Fits 97-08 FLHR, FLTR, FLHX and FLHT models. FLHRCI models require separate purchase of Reflector P/N 59370-98 and 59371-98. 04-08 FLTR, FLHX and FLHRS models require separate purchase of Saddlebag Supports P/N 49194-85 and 90781-93 and two each of P/N 3601 and 7686. (Will not fit Saddlebag Guard Bags.)
B. CHROME REAR SADDLEBAG GUARD KIT
C. GLOSS BLACK REAR SADDLEBAG GUARD KIT
*WARNING: These guards may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). They are not made nor intended to provide protection from bodily injury in a collision with another vehicle or any other object.
D. COMFORT PROFILE REAR SADDLEBAG GUARD KIT

TOURING 393

E. NOSTALGIC ROAD KING CLASSIC SADDLEBAG GUARD RAILS Accentuate the distinctive shape of Road King Classic saddlebags with these unique, contouring guard rails. 91179-10 Fits 09-later FLHRC models. $229.95 91265-98A Fits 98-08 FLHRC/I models only. $229.95 F. NOSTALGIC SADDLEBAG GUARD RAILS Road King model owners can forge a link with the Panhead era by easily bolting on these Nostalgic Saddlebag Guard Rails. Nostalgic twin tube design is manufactured of welded steel tubing and hand-polished with a sparkling chrome finish.
91286-10 $229.95 Fits 09-later FLHR, FLHT and FLHTK models. Also fits FLTR and FLTRU models with separate purchase of Chrome Saddlebag Guard Kit P/N 49282-09B. 90839-94A $229.95 Fits 95-08 FLHT Standard, 94-08 FLHR and 93 FLHS models. (Does not fit FLHX, FLHRC and FLHRS.)
E. NOSTALGIC ROAD KING CLASSIC SADDLEBAG GUARD RAILS
G. TWIN RAIL CHROME SADDLEBAG GUARD KIT Each kit comes with rear saddlebag guards, side rails, mounting hardware and instructions for easy installation.
90892-09 $319.95 Fits 09-later FLHR, FLHT, FLHTK, FLTR and FLTRU models. Stock on 09-later FLHTC and FLHTCU models. FLTR and FLTRU models require separate purchase of Saddlebag Supports P/N 49194-09A and 90781-09A, Nut P/N 7531 (Qty 2) and Antenna Mounting Bracket P/N 76516-09. 91216-97 $319.95 Fits 97-08 FLHT, FLHR, FLHTCUSE/2/3 and 98-08 FLTR models. 04-08 FLTR models require the separate purchase of Saddlebag Supports P/N 49194-85 and 90781-93, Nut P/N 7686 (Qty 2) and Screw P/N 3601 (Qty 2).

I. MAGNETIC TANK TOTE De-clutter your pockets. This compact and convenient magnetic pouch is the ideal place to store small items that would normally go in your jeans pocket. The durable neoprene jacket with zippered closure will keep your items safe for the ride. An embroidered Bar & Shield logo finishes the look. Pouch dimensions: 4" W x 5.5" H.

93300012 $29.95

G. TOUR-PAK LID BRA

H. SADDLEBAG LID BRA KIT

J. BOOM! AUDIO TANK POUCH This portable music system pouch is designed for motorcycle use. The neoprene jacket offers hard-core protection for your portable music device, while the built-in magnets hold the pouch securely to the fuel tank. The clear play-through window permits touch-screen control, and the anti-skid interior insert allows the pouch to accommodate players of various sizes. Simply plug in your headphones or connect your in-dash Advanced Audio Radio with an auxiliary cable, and enjoy your music collection. Two access ports are provided for headphone and output cables. Works well with many MP3 and other personal music players, but should not be used with hard-disk memory players. Window measurement: 2.5" W x 4.0" H.

91003-10 $39.95

I. MAGNETIC TANK TOTE
J. BOOM! AUDIO TANK POUCH

398 TOURING

A. FITTED TOUR-PAK LINER KITS Line your Touring bikes luggage to protect your belongings and reduce noise and rattles on the road. Soft-touch felt-finish liner is formed to the interior for a perfect fit. Molded base and sides maximize the interior room, and one-piece design allows easy removal for cleaning and maintenance. 53301-06 King Ultra Tour-Pak. $79.95 Fits models equipped with King Tour-Pak luggage with wraparound Tail Lamp Kit. Does not fit 10-later CVO Touring models, FLHTK or models with Tour-Pak bottom tub mounted accessories. 53302-07 King Classic Tour-Pak. $79.95 Fits models equipped with King Tour-Pak luggage without wrap-around Tail Lamp Kit. Does not fit with Tour-Pak bottom tub mounted accessories. 53285-06 Chopped Tour-Pak. $69.95 Fits models equipped with Chopped Tour-Pak luggage. Does not fit with Tour-Pak bottom tub mounted accessories. B. FITTED SADDLEBAG LINER KIT Protect your belongings and reduce noise and rattles on the road. Soft-touch felt-finish liner is formed to the hard saddlebag interior for a perfect fit. Molded base and sides maximize the interior room, and one-piece design allows easy removal for cleaning and maintenance.
92189-06 $149.95 Fits 93-later Touring models equipped with Color-Matched hard saddlebags. Does not fit Police model saddlebags.
A. FITTED TOUR-PAK LINER KIT KING CLASSIC SHOWN
B. FITTED SADDLEBAG LINER KIT
C. PREMIER LINER FOR KING TOUR-PAK LUGGAGE High-quality, molded luggage fits perfectly inside the King Tour-Pak. Rigid, yet flexible design holds its shape for easy packing, and functions like traditional travel luggage on your journeys. Luggage features a durable carrying handle, heavy duty zipper, removable shoulder strap and rubber feet to keep the bag upright when out of the Tour-Pak. The interior features cross straps with secure clip to keep clothes in place, and a mesh section for toiletries. The bag is tastefully accented with an embroidered Bar & Shield logo on the zippered exterior pocket. Luggage capacity: 2,900 cubic inches. Dimensions: 22.5" L x 13.0" H x 10.0" D.

94807-09 $229.95 Fits models equipped with Tour-Pak Luggage Racks (except Mini Rack P/N 53100-96). Also fits Premium Sidecar Luggage Rack P/N 53669-89.
B. TOUR-PAK RACK BAG This bag mounts conveniently to your Tour-Pak luggage rack, eliminating the need for bungee cords or tie downs that can scratch paint. Hook-and-loop flaps hold the bag to the rack, so installation and removal is a snap. The foam-backed waterresistant material helps the bag retain its shape for easy loading, and the built-in Bar & Shield logo rain cover features a reflective stripe for added visibility. The bag includes 2 exterior side pockets for storage, 2 interior pockets (1 mesh, 1 soft cotton), and an interior key hook. The bag is 21.0" W x 12.0" T x 11.5" D. Luggage capacity: 2,500 cubic inches.
Fits Tour-Pak lids equipped with Air Wing Tour-Pak Rack P/N 79179-08, Premium Tour-Pak Luggage Rack P/N 5366587, FLHTCUSE Tour-Pak Luggage Rack P/N 79125-06 and Contoured Luggage Rack P/N 79148-06A.

94776-09 94806-09

A. PREMIUM TOUR-PAK RACK BAG
B. TOUR-PAK RACK BAG POLYESTER SHOWN

Leather. Polyester.

$259.95 $139.95
C. PASSENGER PILLION-MOUNTED ULTRA TOURING BAG Pack everything you need for that long, solo ride across the country. This large touring bag is designed to fit the passenger seat of Harley Touring models. The bag includes a waterresistant polyethylene liner that helps the bag retain its shape even when empty. Straps to the saddlebag guards and TourPak mounting rack for convenient installation. The bag is 17.0" W x 19.0" T x 10.0" D. Luggage capacity: 2,800 cubic inches.
94788-01A $199.95 Fits 97-later Touring models equipped with Tour-Pak Luggage and Saddlebag Guards.
D. EXPANDABLE LUGGAGE RACK DUFFEL BAG Urethane-coated 1000 denier nylon with a full-length zipper that wraps around the side gusset panels. Hook-and-loop fasteners attach to luggage rack tubing. Unique shoulder strap doubles as a mounting band. Main compartment zipper is covered by a protective flap secured with hook-andloop closure. Fully expanded: 12.25" H x 12.0" W x 19.5" L. Not expanded: 8" H. Maximum recommended load is 10 lbs.
91753-92 $99.95 For use on Premium Tour-Pak Luggage Rack P/N 53665-87 or Air Wing Rack P/N 79179-08.
C. PASSENGER PILLION-MOUNTED ULTRA TOURING BAG
D. EXPANDABLE LUGGAGE RACK DUFFEL BAG
E. RIDER CUP HOLDER Shaped to blend with the contours of your Harley-Davidson motorcycle, this unique cup holder is easy to reach without cluttering the handlebar. The attractive chrome mount securely attaches to the frame downtube, and sweeps rearward to support the cup holder. The soft-touch insulated holder flexes to grip the beverage, and features a perforated bottom to drain away rain water. Kit includes model-specific clamp, support rod, cup holder and all required mounting hardware. (Available September 2010.)

91843-97 $19.95 Fits 94-later FLHR (except FLHRCI), FLT, FLTR, FLHT, FLHX and Trike models.
*NOTE: It is possible to overload your motorcycles charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicles charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. Ask your dealer for advice about the amount of current consumed by additional electrical accessories.
G. SWITCHED CIRCUIT ADAPTER HARNESS & ELECTRICAL ACCESSORY ADAPTER
H. SUPPLEMENTAL 12V POWER POINT
A. COLOR-MATCHED INNER FAIRING Add a custom touch to your Electra Glide, Street Glide or Road Glide motorcycle with a Color-Matched Inner Fairing and Fairing Cap. Designed to replace the Original Equipment matte black inner fairing, the color-matched finish offers a brilliant contrast to the gauge faces and accessory chrome instrument bezels.
Electra Glide Kit includes inner fairing and fairing cap. Road Glide Kit includes inner fairing, instrument housing and glove box doors.
A. ELECTRA GLIDE COLOR-MATCHED INNER FAIRING
A. ROAD GLIDE COLOR-MATCHED INNER FAIRING

TOURING 415

Road Glide Inner Fairing & Glove Box Doors Electra Glide Inner Fairing
Road Glide Instrument Housing
Electra Glide Fairing Cap
Color Primed Apple Green Big Purple Flake Black Cherry Black Denim Black Ice Pearl Black Pearl Brilliant Silver (Pearl) Candy Red Sunglo Cherry Red Sunglo Chopper Blue Cool Blue Pearl Copper Pearl Copperhead Pearl Crimson Red Denim Crimson Red Sunglo Dark Blue Denim Dark Blue Pearl Dark Candy Root Beer Deep Cobalt Deep Turquoise Fire Red Pearl Flame Blue Pearl Glacier White Pearl Golden Glow Impact Blue Light Candy Root Beer Luxury Blue Luxury Teal Merlot Sunglo Mirage Orange Pearl Pacific Blue Pearl Pewter Denim Pewter Pearl Psychedelic Purple Red Hot Denim Red Hot Sunglo Rich Sunglo Blue Scarlet Red Sedona Orange Smokey Gold Sunset Yellow Pearl Vivid Black White Gold Pearl White Hot Denim White Ice Pearl

PRIMED COLOR-MATCHED

Fits 04-07 Electra Glide and Street Glide models 58508-09BDK 58508-09BPS 58508-09BPY 58508-09BPO 58508-09BXT 58508-09BXY 58508-09BHX 58508-09XE 58508-09BHV 58508-09CGP 58508-09CHH 58508-09CGR 58508-09BPV 58508-09BJL 58508-09DH 58508-09CGS $429.95 $529.95
Fits 08-later Electra Glide and Street Glide models (except Trike) 58468-09BDK 58468-10DHN 58468-09CWR 58468-09BYM 58468-09CWL 58468-09BPY 58468-10BHT 58468-09CPF 58468-10DCG 58468-10DGR 58468-09CPH 58468-09CPL 58468-09CPD 58468-09COZ 58468-09CPG 58468-09CPC 58468-10DID 58468-09CWN 58468-09CWA 58468-09CPJ 58468-09CWT 58468-10DCE 58468-09CHH 58468-09CGR 58468-10DHL 58468-09CYE 58468-09CYS 58468-10DBJ 58468-10DGX 58468-09DH 58468-09CGS 58468-10DHA 58468-10DBV $429.95 $529.95

c. Fl TOURING cleaN FRONT FeNdeR
d. elecTRa GlIde spORT aNd ROad KING FRONT BUmpeR assemBly
*WaRNING:Fenderrailsaredecorativeitemsonly.Do notstrapanythingtotherails.Addinganyadditional weighttothefrontfendercouldadverselyaffectvehicle handling,causinglossofcontrolanddeathorserious injury.
G. FeNdeR RaIl INseRT FRONT
G. FeNdeR RaIl INseRT ReaR
A. CHROME FRONT FENDER TRIM KIT Replace the Original Equipment stainless steel fender trim with a splash of chrome. Kit includes left and right side trim strip.
59209-91T $26.95 Fits 82-later Touring models (except Road Glide and Road King Custom), FLHTCUTG and 86-later FLST, FLSTN and FLSTC models. Does not fit models equipped with clean front fender.
B. BAR & SHIELD CHROME FENDER TIP LENS KIT Chrome-plated polycarbonate construction features translucent Bar & Shield emblems. The kit includes front and rear lenses. Front lens features an amber Bar & Shield, rear lens features a red Bar & Shield. Quick and easy installation. 59081-96 Front and Rear. $27.95 Fits 80-08 FLHT, FLT, FLHS, FLHR models and 86-08 FLSTC, 93-96 FLSTN models. (Does not fit Springer , FLHRS or FLTR models.) C. FENDER TIP LENS KIT WITH SKULL LOGO This chrome-plated Fender Tip Lens Kit adds a little attitude to your ride. The kit features front and rear lenses with a translucent illuminated skull silhouette. The easy-to-install kit includes an amber front lens and red rear lens.
59651-01 $27.95 Fits 80-08 Electra Glide, Tour Glide, FLHS, Road King (except Road King Classic and FLHRS) and 86-08 FLSTC and 93-96 FLSTN models.
A. CHROME FRONT FENDER TRIM KIT
D. LIVE TO RIDE LOGO FENDER TIP Made of durable ABS plastic. Includes mounting hardware and installation instructions. 59068-96 Front. $34.95 Fits 80-later FLT, FLHTCUTG, FLHR, FLSTC and 93-96 FLSTN models (replaces fender lamp assembly). (Does not fit Springer, FLHRS and FLTR models.) 59069-96 Rear. $34.95 Fits 80-08 FLT, FLHR, FLSTC and 93-96 FLSTN models (replaces fender lamp assembly). (Does not fit Springer, FLHRS or FLTR Road Glide models.) E. H-D CLASSIC FENDER TIP Stock on Road King Classic models, these nostalgic-look fender tips are also available for other models. Replaces fender lamp assembly. 59002-98 Front. $31.95 Fits 80-later FL, FLHR and FLHTCUTG models and 86-08 FLSTC models. 59052-98 Rear. $31.95 Fits 80-08 FL and FLHR models and 86-99 FLSTC models. (Does not fit FLSTF and FLTR models.) F. BAR & SHIELD LOGO FRONT FENDER SPEAR This chrome-plated trim spear adds a sweeping dash of chrome to the front fender. Featuring a raised Bar & Shield logo set against a textured black field, this self-adhesive medallion is easy-to-install.
91195-04 $39.95 Fits Touring and FL Softail models (except FLSTSB).

B. BAR & SHIELD CHROME FENDER TIP LENS
C. FENDER TIP LENS WITH SKULL LOGO
G. FRONT FENDER RAIL AND STANCHION KIT* Chrome-plated accents straight from our 1947 catalog. Includes template for easy installation.
91117-97 $69.95 Fits 84-later FL Softail (except FLSTF, FLSTFB, FLSTSE/2 and FLSTSB) and Touring models.
D. LIVE TO RIDE LOGO FENDER TIP
E. H-D CLASSIC FENDER TIP
*WARNING: Fender rails are decorative items only. Do not strap anything to the rails. Adding any additional weight to the front fender could adversely affect vehicle handling, causing loss of control and death or serious injury.
F. BAR & SHIELD LOGO FRONT FENDER SPEAR
G. FRONT FENDER RAIL AND STANCHION KIT

TOURING 419

H. SKULL FENDER SKIRT This decorative chrome-plated fender skirt is a direct replacement for stock fender skirt. Features a three-dimensional sculptured concho with skull design set off with black accents. Mounting hardware included.
59582-02A $54.95 Fits 80-later Touring models, 86-06 FLSTC, 06 FLST and 93-96 FLSTN models equipped with Original Equipment fender skirt.
I. FLAMES FENDER SKIRT Designed as an easy-to-install replacement for the Original Equipment fender skirt, this chrome steel fender skirt features an embossed 3-D flame design. Kit includes mounting hardware. H. SKULL FENDER SKIRT I. FLAMES FENDER SKIRT
60179-06 $54.95 Fits 80-later Touring models, 86-06 FLSTC, 06 FLST and 93-96 FLSTN models equipped with Original Equipment fender skirt.
J. CHROME FENDER SKIRT This rigid-steel fender skirt, designed to replace the original factory-equipped aluminum trim, is formed, polished, and chrome-plated. Its ribbed pattern offers a unique styling element and adds rigidity. Subtle but distinctive brushed aluminum Bar & Shield logos are framed by a stamped-in ribbed outline on both sides.
59228-91 $54.95 Fits 80-later Touring models, 86-06 FLSTC, 06 FLST and 93-96 FLSTN models equipped with Original Equipment fender skirt.
K. ROAD KING CLASSIC FENDER SKIRT The latest in the family of Road King-inspired accessories, this chrome-plated steel fender skirt features four raised accent ribs and a die-cast Road King Classic medallion in chrome with black accents. Mounting hardware included. J. CHROME FENDER SKIRT K. ROAD KING CLASSIC FENDER SKIRT
59005-98 $54.95 Fits 80-later Touring models equipped with Original Equipment fender skirt.
L. V-LOGO FENDER SKIRT V-Logos are die-cast aluminum integrated with the fender skirt, then chrome-plated for a desirable shine. Includes all mounting hardware.
59146-96 $54.95 Fits 80-later Touring models, 86-06 FLSTC, 06 FLST and 93-96 FLSTN models equipped with Original Equipment fender skirt.
59147-96 $54.95 Fits 80-later Touring models, 86-06 FLSTC, 06 FLST and 93-96 FLSTN models equipped with Original Equipment fender skirt.

Fits 08-later Touring models.
42638-08A 40091-10 46883-09 42638-03
Chrome. Edge Cut. Satin Black. Chrome. (Extended)
$164.95 $164.95 $164.95 $164.95
Fits 97-07 Touring models.
B. BILLET STYLE HEEL/TOE SHIFT LEVER Styled to complement our billet style mirror stems, these Billet Style Shift Levers are forged from 6061-T6 aluminum, then machined and polished for a beautiful, custom look. Available in your choice of mirror chrome, satin black powder coat, or Edge Cut black anodized and machined aluminum finishes. Kit includes a front and rear lever and chrome hardware.
Fits 86-later FL Softail and 88-later Touring models.
34535-00B 34045-10 34023-08
A. BILLET STYLE REAR BRAKE LEVER CHROME
B. BILLET STYLE HEEL/TOE SHIFT LEVER CHROME
Chrome. Edge Cut. Satin Black.

$139.95 $139.95 $139.95

A. BILLET STYLE REAR BRAKE LEVER EDGE CUT
B. BILLET STYLE HEEL/TOE SHIFT LEVER EDGE CUT
A. BILLET STYLE REAR BRAKE LEVER SATIN BLACK
B. BILLET STYLE HEEL/TOE SHIFT LEVER SATIN BLACK

TOURING 439

C. BILLET STYLE REAR BRAKE LEVER Styled to complement our billet style mirror stems and shift levers, this Billet Style Rear Brake Lever is forged from 2014-T6 aluminum, then machined and chrome-plated for a beautiful, custom look. Shape matches the Original Equipment lever length found on early-model FL Softail and Touring models. Brake pedal pads sold separately.
42638-00A $159.95 Fits 87-99 FLSTC, FLSTS, FLSTF and FLSTN models, 97-07 FLHT, FLHTC/I, FLHTCUI, FLHR/I, FLHRCI and FLTR/I models.
D. BUCKSHOT HEEL/TOE SHIFT LEVER Styled to complement the Buckshot hand and foot control collection, this forged billet aluminum shift lever lends a custom look to your bike. The chrome lever features a deep groove perforated with counter-bored holes to catch the light and draw the eye. Kit includes front and rear shift lever and installation hardware.
34558-05A $139.95 Fits 86-later FL Softail and 88-later Touring models.
C. BILLET STYLE REAR BRAKE LEVER
D. BUCKSHOT HEEL/TOE SHIFT LEVER
E. FOLDING HEEL SHIFTER Give your left foot a little extra room. Folding Heel Shifter permits the rider to move the rear shift peg out of the way when on the open road, while retaining heel/toe shift functionality around town. Positive detent holds the peg in the selected position, and can be adjusted while riding. Easy to install, the replacement rear lever is chrome-plated, and shaped to match the Original Equipment toe shift lever. Lever accepts stock or accessory shifter peg.

OBSOLETE OBSOLETE

c. chROme ReaR masTeR cylINdeR KIT
d. ReaR masTeR cylINdeR cOVeR
e. chROme JIFFy sTaNd BRacKeT cOVeR
F. JIFFy sTaNd exTeNsION KIT

442 TOURING

Footboards
A. EXTENDED REACH RIDER FOOTBOARD PANS This kit extends the rider footboard forward of the stock location by one inch, providing the tall rider a comfortable riding position. Available in traditional D-shape or Swept Wing design, these footboard pans accept Original Equipment or accessory rider footboard inserts. The kit includes left and right footboard pans.
Fits 02-later Touring models. Also fits 97-01 Touring models equipped with Extended Reach Billet Style Brake Lever P/N 42638-03.

50409-04 54145-10

Traditional Shape. Swept Wing.

$79.95 $79.95

B. BLACK RIDER FOOTBOARD PANS Complete the blacked-out transformation. Replace the Original Equipment chrome footboard pans with sinister gloss black. Kit includes both the right and left pan, and is installed using the Original Equipment hardware and insert pad. Custom footboard inserts are sold separately.
Fits 86-later Touring and 86-later FL Softail models.

51322-08 51060-08

Before After
Traditional Shape. Swept Wing Shape.
A. EXTENDED REACH RIDER FOOTBOARD PAN TRADITIONAL SHAPE
A. EXTENDED REACH RIDER FOOTBOARD PAN SWEPT WING
B. BLACK RIDER FOOTBOARD PAN TRADITIONAL SHAPE
B. BLACK RIDER FOOTBOARD PAN SWEPT WING SHAPE

TOURING 443

C. STREAMLINER RIDER FOOTBOARD KIT Add the sleek sweeping footboard design from the Street Guide to your Touring bike. Kit includes vibration-isolation footboard pads with three chrome bands, and the complete chrome-plated pans that easily bolt in place of the Original Equipment footboards.
50631-04 $179.95 Fits 86-later Touring and 86-later FL Softail models.
Shown with: STREAMLINER BRAKE PEDAL PAD Complement the streamlined footpegs and footboards with this simple-to-install Brake Pedal Pad. The chrome frame surrounds a black rubber pad accented with three chrome bands for style and grip. 42712-04 Large. $54.95 Fits 80-later Touring and 86-later FL Softail models.
C. STREAMLINER RIDER FOOTBOARD KIT (SHOWN WITH BRAKE PEDAL PAD)
D. STREAMLINER PASSENGER FOOTBOARD AND MOUNT KIT
D. STREAMLINER PASSENGER FOOTBOARD AND MOUNT KIT Styled to match the rider footboards on the Road King Custom, Road Glide Custom and Street Glide models, these Swept Wing Passenger Footboards feature a Streamlinerstyle rubber pad surrounded by a chrome accent. The smooth Swept Wing footboard pan is chrome-plated throughout to add a custom touch, even in the folded position. Designed for convenient bolt-on installation, the complete kit includes chrome-plated aluminum footboards, rubber pads, mounting hardware and passenger footboard supports.
50378-07B Fits 93-later Touring models (except Trike). $369.95

F. CHROME FENDER TRIM KIT

G. EXHAUST TRIM

454 TOURING
A. SCUFF GUARDS Guard against heel marks and stone chips on the leading edges of the rear fender and body of your Trike model. These heavyduty molded rubber pads are shaped to match the contour of the body, and are easy to install with the pre-applied adhesive. The ribbed surface pattern mirrors the Original Equipment footboard inserts, and offers a clean, smooth flowing look between the footboards and body.
Fits 09-later Trike models.

1. 83968-10 2. 83976-10

Body Scuff Guards. Fender Scuff Guards.

$24.95 $39.95

B. TRUNK LUGGAGE These well-constructed, ballistic nylon bags are designed to fit perfectly into the trunk of the Trike model. Styled with a reflective Bar & Shield logo, the bags feature zippered outer pouches and a mesh inner storage pocket for packing convenience. Comfortable carrying straps make transportation a breeze. Sold in pairs.
83847-09 Fits 09-later Trike models. $89.95
C. TRIKE TRUNK DOOR ORGANIZER For on-the-road storage and efficiency, this ingenious organizer helps keep smaller items conveniently located on your trunk door for easy access. The easy-to-install self-adhesive organizer features two large nylon-mesh pockets with hookand-loop-secured flaps that offer quick access to keys, cell phones, glasses, gloves, and maps. Organizer features an embossed Harley-Davidson script logo. Add the matching Tour-Pak Lid Organizer P/N 53249-01B inside of the Tour-Pak luggage for maximum organization.
93300001 Fits 09-later Trike models. $59.95

A. SCUFF GUARDS

D. TRIKE TRUNK INTERIOR LIGHT KIT Dont be left in the dark. This bright convenience lamp kit turns night-time into day when you open your Trikes trunk. Two brilliant white LED light pods mount inside the trunk to illuminate the interior, and the included contact switch turns the light on and off when you open and close the door. A 5-minute auto shut-off timer prevents battery drain. Kit includes wiring harness and installation hardware.
83946-11 Fits 09-later Trike models. $79.95

B. TRUNK LUGGAGE

C. TRIKE TRUNK DOOR ORGANIZER
D. TRIKE TRUNK INTERIOR LIGHT KIT

TOURING 455

e. TRIke ReAR FeNdeR BRA Protectyourtrikesrearfendersfrombootscuffsandroad debris.TheserichblackFenderBrasareconstructedofnonabrasivefleece-backedsmoothvinyl,andaresimpletoinstall. FeaturingaprominentembossedBar&Shieldlogo,these BrasarestyledtocoordinatewiththematchingFairingBra P/N57800-00andtheTour-PakLidBraP/N57844-05. 57892-11 $99.95 Fits09-laterTrikemodels.NotcompatiblewithChrome FenderTrimKitP/N83812-09. F. TRANspAReNT pAINT GUARd kIT Thistransparentskinisdesignedtoprotectpartsofthetrike bodyworkfrombootscuffsandroaddebris.The12piecesof crystal-clearmaterial(6perside)protecttheareasurroundingthepassengerfootboard,andarepre-cuttofittheleadingandinnersurfaceoftherearfender,thefasciapanelofthe trunk,andthesidecovers.Theapplicationprocessissimilar tothatoftintedwindowfilm,andthematerialcanberemoved andreplacedwhenitisnolongercosmeticallyappealing. 83989-10 $129.95 Fits09-laterTrikemodels. e. TRIke ReAR FeNdeR BRA F. TRANspAReNT pAINT GUARd kIT G. pRemIUm COTTON INdOOR sTORAGe COveR TRIke We take these indoor covers one step further.Additional processingprovidesasofternaptotheheavyweight8-oz. cotton.Thepremiumcottonmaterialisbreathable,allowing moisturetoescapewhenyourbikeisinstorage.Accented withanembroideredBar&Shieldlogo,thiscoverfeatures elasticedgesandincludesaconvenientstoragebag. 84036-11 $199.95 Fits09-laterTrikemodels. h. INdOOR/OUTdOOR mOTORCyCle COveR Our most versatile cover, this all-weather, indoor/outdoor coverismadeofatough,lightweight300denier,faderesistant polyester.The urethane-coated material and double stitchedseamsprovideexcellentstrengthandwaterresistance.Ventingsystemallowscondensationtoescapeduring long-termstorage.Exhaustheatshieldpanelsprotectthe coverfromhotexhaustsystems.Additionalfeaturesinclude aprotectivewindshieldliner,securingstrap,elasticedges, and a convenient storage pouch. Features hook-and-loop securedopeningstoaccommodatedualantennas.Features silkscreenedEaglelogo. 83845-09 $149.95 Fits09-laterTrikemodels.