Press MUTE once to turn the sound off or on. In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. See Using Channel Scan and Programming Favorite Channel Scan. Use CH+ (or CH-) to select the next higher (or lower) channel.
3. Press and hold SET until the LED (red light) blinks twice, then release SET. 4. Use the Manufacturers Codes (on the back) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again.

CHECKING THE CODES

If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: 1. On the remote control, press TV once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 9 - 0. The LED will blink twice. 4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., three blinks = 3) and write down the number.
NOTE: If a code digit is 0, the LED will not blink.
Macro keys are ideal for home theater operations, setting a favorite channel, guide steps, or other multiple functions you would like to control with one key press. Moreover, each macro key can hold up to15 key presses total.
NOTE: Programming a new macro over an existing one will erase the original macro.
learning. Be sure to press each key within 10 seconds of the previous entry. If not, the remote control will exit the programming mode.
2. Enter 9 - 9 - 4. The LED will blink twice. 3. Press the destination mode twice (where keymoved keys are stored). The LED will blink twice. PROBLEM:
set up. Make sure they can be operated with an infrared remote control. TV/VCR combo does not respond properly. SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: Changing channels does not work properly. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. PROBLEM: During learning, LED emits a long blink after pressing and holding key to be learned.
Programming A Learning Key
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 7 - 5. The LED will blink twice. 3. Press a device key once (e.g., TV) to assign a mode for learning. 4. Press an open learning key once (e.g., L1) to store a feature to be learned. The LED will blink rapidly for 4 seconds. If the LED does not blink rapidly, go back to step 1 and start again. 5. Place your original remote control (e.g., TV remote control) head-to-head (about 2" apart) from the One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. 6. On your original remote control, press and hold the key (i.e., feature) to be learned until the LED on the One For All 8L Universal Remote Control blinks twice. If the LED does not blink twice, repeat steps 3 through 6. 7. To learn functions onto other learning keys (e.g., L2 ~ L4), repeat steps 3 through 6. 8. To lock in new feature(s) on the One For All 8L Universal Remote Control, press and hold SET until the LED blinks twice, then release SET. 9. To test a learned feature, press a device key (e.g., TV) once where the learning mode was assigned. Then press the learning key (e.g., L1) where the learned feature is stored.

8L DEVICE HOME THEATER

UNIVERSAL REMOTE CONTROL WITH LEARNING
Programming A Favorite Channel
With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, lets assume your favorite cable programs are on channel 71. Use the following instructions to program a macro key for direct access of this channel:

NOTE: This example assumes the TV tuner is connected directly to the cable line and not through a cable box.

CHANGING VOLUME LOCK

The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a devices volume will be locked to one mode (e.g., to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code.
NOTE: If the device does not have a POWER key, press the (Play) key.
Press PREV once to recall the last-viewed channel and to page back one screen on the main menu. In the CD mode, use PREV to turn random play on or off. In the RCVR/AMP mode, use PREV to select the receiver band. Use the keypad (1 ~ 9 and 0) to directly select channels (for example, 009 or 031). In the RCVR/AMP mode, use the keypad (1 ~ 9 and 0) to select audio sources 1 through 10. Press ENTER once after entering the channel numbers on some TVs. In the CD mode, use ENTER to add 10 to the digit entry (e.g., ENTER and 7 is 17). Use TV/VID to switch the TVs input to view TV or video programs. Use the transport keys to control your VCR, DVD or CD player, or VOD (Video On Demand) if available on your cable or satellite service. To record a VCR program, press REC twice. After programming, press M1~ M4 once to run a desired macro (see Using Macros).
6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the boxes below: TV Code: VCR Code: DVD Code: SAT Code: CD Code: CBL Code: RCVR/AMP Code: AUX Code: Aux. Device Type: _______________________________
5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. 6. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking.
Locking Volume Control To One Mode (Global Volume Lock):
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV). The LED will blink twice. 3. Now, when you press VOL+, VOL, or MUTE, the volume of the selected device (e.g., TV) will be controlled regardless of the mode you have selected.
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Select an open macro key (e.g., M1) and press it once. 4. Press TV once. 5. Enter the channel number, 7 - 1.

NOTE: If you have access to over 100 channels, enter 0 -7 -1. Moreover, if the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -7 -1-Enter).
SOLUTION: A bad capture has occurred.Avoid high-ambient light sources, such as direct daylight and fluorescent bulbs. Try readjusting positions of remote controls before performing the procedure again. PROBLEM: Tried Search For Your Code method and still could not find a working code.
USING THE HOME THEATER MODE
The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning includes a custom Home Theater mode. After the HOME THEATER key is programmed, it will allow you to access five groups of remote control keys without having to change device modes.
Unlocking Volume Control For A Single Device (Individual Volume Unlock):
1. After performing Global Volume Lock (above), press and hold SET again until the LED (red light) blinks twice, then release SET. 2. Press a desired mode key where you want volume to be unlocked (e.g., RCVR/AMP) and controlled within its own mode. 3. Enter 9 - 9 - 3 and then press VOL once. The LED will blink four times. 4. If desired, repeat steps 1 through 3 (of this section) for each device that you want volume to be unlocked. 5. Now, after you select a device that has volume unlocked (e.g., RCVR/AMP), pressing VOL+, VOL, or MUTE, will control the devices volume only in its own mode.
SOLUTION: Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Next enter 9 - 9 - 2. Then press the device key to be cleared twice. Now repeat the Search For Your Code method. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo.

Control Organization

About Control Groups
6. Press and hold SET until the LED blinks twice, then release SET. Now when you press M1, you will instantly see cable channel 71 on your TV set.
Deleting Functions From The Learning Keys:
1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 7 - 6. The LED will blink twice. 3. Press the device key once where the learned feature is stored (e.g., TV). 4. Press the learning key (e.g., L1) to be deleted twice. The LED will blink twice after the second press. 5. To clear additional functions stored on other learning keys, repeat steps 1 through 4 (in this section).
For Home Theater programming, the remote controls keys are grouped by type of control into the following five control groups: (1) Transport Controls: (2) Volume Controls: (3) Channel Controls: (4) Menu Controls: (5) PIP Controls: PLAY, STOP, FWD, REW, PAUSE, and REC VOL+, VOL-, and MUTE CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT PIP, MOVE, and SWAP

SOLUTION: For power on, these products require programming TV codes. For Sony, use TV code 0000 and VCR code 0032. For Sharp, use TV code 0093 and VCR code 0048. PROBLEM: CH+ and CH- do not work for your RCA TV. SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. PROBLEM: No remote control of volume. SOLUTION: See Changing Volume Lock to lock/unlock volume.
Programming A Master Power Key With Instant Channel Selection
A macro key can be programmed to turn on and off your equipment as well. For example, lets set up a sequence that will turn on the TV and tune it to channel 3, and then turn on the Cable Box and tune it to a premium channel (e.g., 11).
NOTE: This example assumes all equipment is turned off and that the TV is connected through the cable box with TV tuning set to channel 3.
Unlocking All Volume Control (Restoring Default Setting):
NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode, etc.).

RE-ASSIGNING DEVICE KEYS

The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning can be set to control a second TV,VCR, DVD player, or other device. For example, to control a TV, a cable box, and two VCRs, you will need to re-assign the unused AUX key to operate the second VCR as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 2. The LED will blink twice. 3. Press VCR once, then press AUX once. 4. The AUX key is now ready to be programmed for your second VCR. See Programming Device Control. To re-assign other device keys to the AUX key, repeat steps 1 through 4 above by substituting the sequence from the below chart:

CUSTOMER SUPPORT

For assistance, please contact us in any of the following ways: E-mail: ofasupport@ueic.com Internet: http://www.oneforall.com Consumer Help Line: (330) 405-8616
PROGRAMMING TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.

About Device Groups

1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Select an open macro key (e.g., M2) and press it once. 4. Enter the following sequence: TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels)
NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -7 -1-Enter).

Moreover, the remote controls devices are grouped into the following five device groups: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: (1) Device Group 1: (2) Device Group 2: (3) Device Group 3: (4) Device Group 4: (5) Device Group 5: VCR, DVD, CD, and RCVR/AMP TV, VCR, CBL, SAT, CD, and RCVR/AMP TV, VCR, CBL, SAT, CD, and RCVR/AMP TV, VCR, CBL, SAT, and DVD TV VCR TV CBL CBL TV
1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink four times. 3. Volume will again be independently controlled according to its default states for all programmed devices.

USERS GUIDE

INTRODUCTION
The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning (URC-8811) is designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires four (4) fresh AAA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here.Also, keep these instructions for future reference.
After programming, press L1~ L4 once to activate a learned function (see Using Learning Keys). Use PIP to switch the Picture-In-Picture feature on or off (if available on your TV). Use MOVE to move the window picture to different positions in the main picture. Use SWAP to switch images and sound between the main and window pictures. Press SLEEP to activate your devices sleep timer (not available for all devices). Use to turn on or off the key backlight. When this feature is activated, keys will remain backlight for 5 seconds after the last key press. Use SET for all programming sequences.

LIMITED WARRANTY

One For All warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase. This limited warranty is valid only on ONE FOR ALL product purchased and used in the United States of America or Canada, and does not apply to products used for industrial or commercial purpose. The limited warranty does not cover damage or failure caused by products or services not supplied by ONE FOR ALL , or which result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God. There are no express warranties except as listed above. ONE FOR ALL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase.A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. One For All (330) 405-8655

2. On the remote control, press VCR. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. 4. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

ABOUT UPGRADING

The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote controls memory. If this happens, please contact our Customer Support department (see Customer Support below) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If the code for your home entertainment or home automation device is not in our database, we will need to capture the code for that device from its original remote control. A new code would then be created and entered into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If necessary, the Customer Support representative can instruct you how to begin the capture procedure.
NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality.
The default Device Group setting from the factory is:
5. Then enter the following sequence: CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels) 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press M2 once, the TV will turn on and tune to channel 03. Then the cable box will turn on and tune to channel 11.

To Re-Assign Device Key

AUX as 2nd TV key: AUX as 2nd DVD key: AUX as 2nd SAT key: AUX as 2nd CD key: AUX as 2nd CBL key: AUX as 2nd RCVR/AMP key:

Perform Sequence

SET - 9 - 9 - 2 - TV - AUX SET - 9 - 9 - 2 -DVD- AUX SET - 9 - 9 - 2 -SAT- AUX SET - 9 - 9 - 2 -CD- AUX SET - 9 - 9 - 2 -CBL- AUX SET - 9 - 9 - 2 - RCVR/AMP - AUX

Clearing A Macro

1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 5. The LED will blink twice. 3. Select a macro key (e.g., M1~M4) you want to clear and press it once. 4. Press and hold SET until the LED blinks twice, then release SET.

FEATURES AND FUNCTIONS

Use the Key Charts (below) to learn how to use the universal features and functions of the One For All 8L Home Theater Upgradeable Universal Remote Control with Learning (URC-8811).
5. Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code.
Programming The Home Theater Mode
For example, lets assume you have a TV, a cable box, and a VCR in your home theater system.You can set up the Home Theater mode so that selected controls are assigned to these devices as follows: 1. On the remote control, press HOME THEATER. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 7 - 9. The LED will blink twice. 4. Select a device. For this example, press VCR once. Then assign a desired Control Group to the device. For this example, press PLAY once, which will assign the entire group of Transport Controls (i.e., PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. The LED will blink once. 5. Select another device. For this example, press TV once. Then assign a desired Control Group to this device. For this example, press VOL+ once, which will assign the entire group of Volume Controls (i.e., VOL+, VOL-, and MUTE) to the TV. The LED will blink once. 6. Select another device. For this example, press CBL once. Then assign a desired Control Group to this device. For this example, press CH+ once, which will assign the entire group of Channel Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, and TV/VCR) to the Cable Box. The LED will blink once. 7. To add additional Menu functionality to the Cable Box, press CBL once. Then press MENU once. This action will assign the entire group of Menu Controls (i.e., MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT) to the Cable Box. The LED will blink once. 8. To add PIP functionality to the TV, press TV once. Then press PIP once. This action will assign the entire group of PIP Controls (i.e., PIP, MOVE, and SWAP) to the TV. The LED will blink once. 9. To exit Home Theater programming, press and hold SET until the LED (red light) blinks twice, then release SET.

Key Charts

The LED (red light) blinks to show that the remote control is working and is sending signals. ` Press TV, VCR, DVD, AUX, SAT, CD, CBL, or RCVR/AMP once to select a desired home entertainment device to control. After programming, press HOME THEATER once to select the home theater mode (see Using The Home Theater Mode). Press POWER once to turn on or off the selected device. Press MENU once to display your selected devices main menu. Use GUIDE to display your selected devices program guide or setup menu. Use EXIT to exit from your selected devices guide or menu. Use INFO to display the current channel and program information. Use the cursor keys to move the cursor in the program guide and menu screens. Use SELECT to choose options from your selected devices menu or guide. In the CD mode, use SELECT to select a compact disc. Use v (or w) to select the next (or previous) CD. Use (or ) to select the next (or previous) track.
6. If youve located a setup code that works, but it has a separate TV code, youll also need to program it into the remote control to access volume control as follows: a. Press TV once. The LED (red light) will blink twice. b. Enter the TV code for your TV/VCR Combo. If correct, the LED will blink twice.
NOTE: For VCR/TV Combos programmed with separate TV codes, TV volume is controlled by pressing VCR first and then TV. After that, use VOL+ (or VOL-) to raise (or lower) the TV volume. For other alternatives on controlling your volume keys, see the Changing Volume Lock or Using Keymover sections.

USING CHANNEL SCAN

In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed see Programming Favorite Channel Scan below) and/or all channels for the selected mode. 1. If Favorite Channel Scan has been set up, skip to step 2. Otherwise, press TV, VCR, DVD, SAT, or CBL once. 2. Press FAV once. If Favorite Channel Scan has been set up, scanning of favorite channels will start and, upon completion, continue to scan all channels upward for the same device. If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up, and continue until all channels of the selected device is scanned. 3. To stop scanning channels at any time, press any key once (except the backlight key ).

You can also re-sassign another unused device key by substituting an open key for the AUX key in the above chart and performing the sequence. For example, to re-assign an unused SAT key as a 2nd CD key, perform SET - 9 - 9 - 2 -CD- SAT. When a re-assignment is done, the LED (red light) will blink twice to confirm your choice.At that time, you will need to program the remote control for the new device (see Programming Device Control).

INSTALLING BATTERIES

1. On the remote controls back, push the tab and lift off the battery cover. 2. Obtain four (4) new (fully-charged) AAA alkaline batteries. Match the + and marks on the batteries to the + and marks in the battery case, then insert the new batteries. 3. Press the battery cover back into place. The tab should click when the cover is locked. 4. Test the remote control by first pressing POWER and then any mode key (e.g., TV). If batteries are inserted correctly, the LED (red light) will blink once.
NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones to ensure all of your programming information is restored.

USING KEYMOVER

The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning includes a Keymover feature that allows you to map (or copy) keys from one mode (i.e., source mode) to another mode (i.e., destination mode).
NOTE: The following keys cannot be used as a source or destination: TV, VCR, DVD, AUX, SAT, HOME THEATER, CD, CBL, RCVR/AMP, and SET.

Upgrade Exclusions

Home entertainment or home automation devices controlled by radio frequency (RF/UHF), wired, or ultrasonic remote controls. Only devices controlled by infrared remote controls are covered. Home entertainment or home automation devices not controlled by remote controls. Broken or defective product. Products that operate over 100 kHz. Infrared keyboards and infrared pointing devices (such as mouse substitutes). All products for sale and/or use outside the continental United States, Hawaii,Alaska, or Canada.
7. For future reference, write down the working TV/VCR combo code in the below boxes: TV/VCR Code: TV Code (if used):

Programming Keymover

For example, if your VCR does not have volume control, you can map the volume and mute keys from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 - 9 - 4. The LED will blink twice. 3. For the source mode, press TV once. 4. For the source key, press VOL+ once. 5. For the destination mode, press VCR once. 6. For the destination key, press VOL + once. 7. The LED will blink twice indicating the keymoved sequence is correct. 8. Repeat steps 1 through 7 twice more, substituting VOL and MUTE as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning to control the TVs volume and mute in the VCR mode, as well as in the TV mode.

PROGRAMMING FAVORITE CHANNEL SCAN
In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan).
NOTE: Only channels of one mode can be stored for Favorite Channel Scan.

TROUBLESHOOTING

PROBLEM: If you own a satellite that uses code 0775 (Express Vu and Echostar) and your exit key does not work, perform the following sequence to activate this feature/function. 2. Press and hold the SET key until the red LED blinks twice 3. Press 9-9-4, the red LED will blink twice 4. Press SET and release (one blink on LED) 5. Press 3-3-6 6. Press the EXIT key, the red LED will blink twice. The Exit key will now correctly perform the exit feature/function on your satellite. PROBLEM: PROBLEM: LED (red light) does not blink when you press a key. LED blinks when you press a key, but home entertainment device does not respond. SOLUTION: Replace batteries with four new AAA alkaline batteries.

ADDITIONAL INFORMATION

As you update your home entertainment system, One For All has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you. One For All Access 3..URC-3605 One For All Video Expert 4 Device..URC-4081 One For All Video Expert Plus 4L...URC-4880 One For All Access 4..URC-4605 One For All Access 5..URC-5705 One For All 6 Device Home Theater..URC-6011 One For All 8 Device Home Theater..URC-8011 One For All 8L Device Home Theater with Learning Capability..URC-8811 One For All A/V LCD 8 Device With Learning.URC-8910 One For All IR/RF LCD 8 Device With Learning.URC-9910 ONE FOR ALL is the registered trademark of Universal Electronics Inc. Computime International Ltd. is the Licensee of the ONE FOR ALL brand for USA and Canada. Copyright 2002 by Universal Electronics Inc.No part of this publication may be reproduced,transmitted,transcribed,stored in any retrieval system,or translated to any language,in any form or by any means, electronic,mechanical,magnetic,optical,manual,or otherwise,without the prior written permission of Universal Electronics Inc. The One For All 6 Device Universal Remote Control is compatibile for use in North America, excluding Mexico. URC-8810w/8811 02/02

SEARCHING FOR YOUR CODE

If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. On the remote control, press TV once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 9 - 1. The LED will blink twice. 4. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off.
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
PROGRAMMING DEVICE CONTROL
The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a One For All home automation device. To control devices other than the default brands, perform the following steps; otherwise skip this section:
NOTE: For TV/VCR Combo control, see the next section.
1. On the remote control, press TV, VCR, DVD, SAT, or CBL once. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 9 - 6. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once.
NOTE: If the original remote control required pressing an Enter key to change the channel, also press the Enter key after the channel number (e.g., 0 -3-1-Enter).
SOLUTION: 1. Press the CBL/SAT key
Operating The Home Theater Mode
After programming the Home Theater key (see previous), you simply activate this mode by pressing HOME THEATER once. Instantly, groups of remote control keys will be assigned to their programmed devices. For the above example, pressing HOME THEATER once would assign the following keys to the VCR, TV, and Cable Box: VCR: TV: Cable Box: PLAY, STOP, FWD, REW, PAUSE, and REC VOL+, VOL-, MUTE, PIP, MOVE, and SWAP CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP, INFO, TV/VCR, MENU, GUIDE, Cursor Controls (Up, Down, Left, Right), SELECT, and EXIT
In the RCVR/AMP mode, use SELECT to set the surround sound. Use v (or w) to adjust the volume higher (or lower). Use (or ) to adjust the balance left (or right).

1. Turn on a device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key
5. To lock in the code, press and hold SET until the LED blinks twice, then release SET. 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for.
5. If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming.
1. Press a device key that has a keymoved key. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. 3. Enter 9 - 9 - 4. The LED will blink twice. 4. Press the destination key twice (where the keymoved key is stored). The LED will blink twice.
Restoring All Keymoved Keys In A Single Mode
Use VOL+ (or VOL-) to raise (or lower) the sound volume.
2. On the remote control, press a device key once (i.e., TV, VCR, DVD, AUX, SAT, CD, CBL, or RCVR/AMP).
NOTE: Use the AUX key to program control of home automation devices as well as miscellaneous audio services and video accessories. Alternately, use the AUX key to program control of a second device type (e.g., a second VCR; see Re-assigning Device Keys).
6. To exit programming, press and hold SET for 3 seconds. The LED will blink twice.

USING MACROS

With programming, the M1 through M4 keys on your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning can be setup to perform repetitive, time-consuming operations for easy, convenient access through the press of a single key.

USING LEARNING KEYS

Use the learning keys (L1 ~ L4) to add functions that are unique to your home entertainment devices (e.g.,VCR Tracking Up or Down).
NOTE: Please have your original remote controls handy before programming
SOLUTION: Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. PROBLEM: The unit does not control home entertainment devices or commands are not working properly.
1. Press and hold SET until the LED (red light) blinks twice, then release SET.
SOLUTION: Try all listed codes for the device brands being

CTGAE3P 3021 manual booklet

5/24/04

12:46 PM

Page 1

Page 2

TABLE OF CONTENTS

Introduction. 3 Features And Functions. 4
Key Charts. 5 Device Table. 6
Installing Batteries. 7 Programming Device Control. 8 Searching For Your Code. 9 Checking The Codes. 9 Programming A Master Power Macro. 10
Programming The Power Key For The Master Power Macro. 10 Operating The Master Power Macro. 10 Clearing The Master Power Macro. 11
Re-Assigning Device Keys. 11 Using Channel Scan. 11 Programming Favorite Channel Scan. 12 Changing Volume Lock. 12
Locking Volume Control To One Mode (Global Volume Lock). 12 Unlocking Volume Control For A Single Device (Individual Volume Unlock). 13 Unlocking All Volume Control (Restoring Default Setting ). 13
Clearing Custom Programming. 14 Restoring Factory Default Settings. 14 Troubleshooting. 15 Instructions To The User. 15 Lifetime Warranty. 16 Additional Information. 17 Manufacturers Codes. 18
Setup Codes For Cable Boxes. 18 Setup Codes For Cable Box/PVR (or DVR) Combos. 18 Setup Codes For DVD Players. 18 Setup Codes For DVD Player/VCR Combos. 18 Setup Codes For PVRs (or DVRs). 19 Setup Codes For Satellite Receivers. 19 Setup Codes For Satellite Receiver/PVR (or DVR) Combos. 19 Setup Codes For TVs. 19 Setup Codes For TV/DVD Player Combos. 20 Setup Codes For TV/VCR Combos. 20 Setup Codes For TV/VCR/DVD Player Combos. 21 Setup Codes For VCRs. 21

Page 3

INTRODUCTION
The One For All 3 Device Universal Remote Control (URC-3021) is designed to remotely operate up to three home entertainment devices. It also features intuitive and easy-to-use keys for instant control of DVD and PVR (or DVR) components. Moreover, its sophisticated technology will allow you to consolidate your original home entertainment remote controls into one easy-to-use product. Advanced features include:
Intuitive buttons to allow easy access to functions and menus on your DVD player, PVR (or DVR), and Cable/Satellite devices Direct code setup for easy device programming Step-and-Set code search and Code Verification for an alternate way to program devices Power Macro for master on/off control of all of your equipment with a single keystroke Volume Lock/Unlock feature to lock or unlock the volume control to one mode or individual modes Device Key Re-Assignment to remotely control a second (duplicate) device Channel Scan and Favorite Channel Scan for easy channel surfing Color-coded keys to quickly locate popular functions Extensive code library for popular video devices including DVD players and PVRs (or DVRs)
The URC-3021 remote control requires two (2) new AAA alkaline batteries (not included) and some easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep this guide for future reference.

Page 4

FEATURES AND FUNCTIONS
Use the illustration below to locate features on the One For All 3 Device Universal Remote Control (URC-3021) and then study the Key Charts (on the next two pages) to learn how they function. To find out what type of devices can be controlled by each device key after programming, see the Device Table on page 6.

Page 5

Key Charts
When the LED (red light) blinks, the remote control is working and (after programming) is sending signals. Press DVD/VCR, CBL/SAT, or TV once to select a desired home entertainment device to control. Also see the Device Table on page 6. Press POWER once to turn on or off the selected device. For master power control, see Programming A Master Power Macro on page 10. Use the keypad (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031).
Use TV/VID to switch the TVs input to view TV or video programs. Press ENTER once after entering the channel numbers on some TVs. Use GUIDE to display your selected devices program guide or setup menu. Press MENU once to display your selected devices main menu. Use INFO to display the current channel and program or on-screen directory. Use EXIT to exit from your selected devices guide or menu. Use the Cursor Keys to move the cursor in the program guide and menu screens. Use SELECT (OK) to choose options from your selected devices menu or guide. Press LAST once to recall the last channel. Use FAV to scan all channels, or after programming, to scan up to10 favorite channels. Use CHL (or CHM) to select the next higher (or lower) channel. Press SUBTITLE/CC once to display (or turn off) subtitles or closed captions,if available on your DVD player or cable/satellite service. For a PVR (or DVR), press PVR MENU once to display a list of your recorded shows. Press MUTE once to turn the sound off or on. Use VOLL (or VOLM) to raise (or lower) the sound volume.

Page 6

Use REW, PLAY, FWD, PAUSE,or STOP to control your VCR, PVR (or DVR), or DVD player. For a DVD player, use SKIP F. or SKIP R. to view the next or previous chapter. For a VCR, PVR (or DVR), or VOD (if available), use SCANor SCAN+ to quickly scan forward or back through a video program. Use REPLAY for an instant replay. Use QUICK SKIP to advance the video program a preset amount (as set on your device). Press REC twice to record a VCR or PVR (or DVR) program. Use SLEEP to set the sleep timer on a selected device if equipped with this feature. Use SET for all programming sequences.

Device Table

NOTE: Please refer to the table below when performing the instructions in Programming Device Control on page 8.
After programming, the One For All 3 Device Universal Remote Control will be able to control the following types of devices:
DEVICE KEY CONTROLS THESE TYPES OF DEVICES DVD Player VCR PVR (or DVR) TV/DVD Player Combo VCR/DVD Player Combo TV/VCR Combo TV/VCR/DVD Player Combo VCR/DVD Player Combo Cable Box (or Converter) Cable Box/PVR (or DVR) Combo Satellite Receiver Satellite Receiver/PVR (or DVR) Combo

Television

Page 7

INSTALLING BATTERIES

On the remote controls back, push the tab and lift off the battery cover. Obtain two (2) new AAA alkaline batteries. Match the + and marks on the batteries to the + and marks in the battery case, then insert the new batteries. Press the battery cover back into place. The tab should click when the cover is locked. Test the remote control by pressing any mode key (e.g., TV). If the batteries are inserted correctly, the LED (red light) will blink.
NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 10 minutes to ensure all of your programming information is restored.

Page 8

PROGRAMMING DEVICE CONTROL
The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box. To control devices other than the default brands, perform the following steps; otherwise skip this section: 1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.
On the remote control,press a device key once (i.e., DVD/VCR, CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR), TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions. NOTE: To program control of a DVD Player, DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions. NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.
Press and hold SET until the LED (red light) blinks twice, then release SET. Use the Manufacturers Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesnt work, try Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY.
Repeat steps 1 through 5 for each device you want to control.For future reference,write down each working device code in the following boxes:

DVD/VCR Code:

Device Type:__________________

CBL/SAT Code:

TV Code:

Page 9

SEARCHING FOR YOUR CODE
If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code.
NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and insert the required media.
For example, to search for a code for your TV: 1. 2. 3. On the remote control, press TV once. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 1. The LED will blink twice.

Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off (after pressing POWER). If the device does not have a Power key, you can substitute another function, such as digits 0 ~ 9 , CH L, or PLAY).
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
To lock in the code, press and release SET. The LED will blink twice. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for.

CHECKING THE CODES

If you have set up the remote control using the Searching For Your Code procedure as above, you may need to find out which four-digit code is operating your equipment. For example,to find out which code is operating your TV: 1. 2. 3. On the remote control, press TV once. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 0. The LED will blink twice.
To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8.
NOTE: If a code digit is 0, the LED will not blink.

Page 10

Repeat step 4 (on the previous page) three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.Write down the code digits in the remaining TV code boxes on page 8. 6. To check for codes of other devices, repeat steps 1 through 5 (starting on the previous page), but substitute the appropriate device key for each device you are checking.Write down the devices code digits in the appropriate code boxes on page 8.
PROGRAMMING A MASTER POWER MACRO
In its default state, the POWER key on the One For All 3 Device Universal Remote Control will individually power your home entertainment devices on or off. However, you can also program a Master Power Macro onto the POWER key that will sequentially turn on or off all the devices with a single key press.
Programming The Power Key For The Master Power Macro
1. 2. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 5. The LED will blink twice. Then press POWER once.

3. 4. 5.

For the first device you want in the power-on sequence, press its device key (e.g., CBL/SAT) once. Repeat step 3 up to two more times to add desired devices to the power-on sequence (e.g., DVD/VCR and TV). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET.

Operating The Master Power Macro
1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices.
NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off.
Devices will turn on (or off) according to your programmed sequence.
NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. continued on next page.

Page 11

PROGRAMMING A MASTER POWER MACRO (contd)
Clearing The Master Power Macro
Press and hold SET until the LED blinks twice, then release SET. The Master Power Macro is now cleared.

RE-ASSIGNING DEVICE KEYS

The One For All 3 Device Universal Remote Control can be set to control a DVD player and a VCR (or a PVR) or a second DVD player by re-assigning the unused CBL/SAT key as follows: 1. 2. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 2. The LED will blink twice.
Press DVD/VCR once. Press CBL/SAT once.The LED will blink twice.The CBL/SAT key is now ready to be set up to control your VCR (or PVR) or second DVD player.See Programming Device Control on page 8.
NOTE: Only one device can be assigned to an unused device key at a time.

USING CHANNEL SCAN

In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all channels. Or, if programmed, use the FAV key to scan only your favorite channels to view a desired channel (see Programming Favorite Channel Scan on next page. ) 1. Press CBL/SAT or TV once.

Press FAV once.

If Favorite Channel Scan has been set up,scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key.
To stop scanning channels at any time, press any key once.

Page 12

PROGRAMMING FAVORITE CHANNEL SCAN
In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device).

On the remote control, press CBL/SAT or TV once.
Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 6. The LED will blink twice.
Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once.
NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e.g., 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER.
If desired, repeat step 4 for each channel to be stored, up to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. To change your favorite channel list at this point, you will first need to delete the existing list by performing the steps in Clearing Custom Programming on page 14. Then, perform the instructions in this section once again.
To exit programming with less than 10 favorite channels stored, press and hold SET until the LED blinks twice. Otherwise, the remote control will automatically exit the program after 10 channels have been stored.

CHANGING VOLUME LOCK

The One For All 3 Device Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a devices volume will be locked to one mode (e.g., to control TV volume in all other modes).After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
Locking Volume Control To One Mode (Global Volume Lock)
1. Press and hold SET until the LED (red light) blinks twice, then release SET.

continued on next page.

Page 13
CHANGING VOLUME LOCK (contd)
2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV). The LED will blink twice.
Now, when you press VOL L, VOLM, or MUTE, the volume of the selected device (e.g., TV) will be controlled, regardless of the mode you have selected.
Unlocking Volume Control For A Single Device (Individual Volume Unlock)
1. After performing Global Volume Lock (above),press a desired mode key where you want volume to be unlocked (e.g., DVD/VCR) and controlled within its own mode. Press and and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 3 and then press VOLM once. The LED will blink four times.

If desired, repeat steps 1 through 3 (of this section) for each device that you want volume to be unlocked. After selecting a device that has volume unlocked (e.g., DVD/VCR), pressing VOL L, VOLM, or MUTE will control the devices volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting)
NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in DVD/VCR mode, etc.).
On the remote control, press and hold SET until the LED (red light) blinks twice,then release SET. Enter 9 - 9 - 3 and then press VOL L once. The LED will blink four times.
Volume will again be independently controlled according to its default states for all programmed devices.

Page 14

CLEARING CUSTOM PROGRAMMING
The One For All 3 Device Universal Remote Control contains an Operational Feature Reset program. If desired, you can use it to clear custom programming, except your setup codes and reassigned device keys, and reset them to original factory settings.Also see Restoring Factory Default Settings below.
IMPORTANT: Executing this program will erase all your custom settings for Power Macro, Favorite Channels, and Volume Lock.
Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 8 - 0. The LED will blink twice. The remote control will return to normal operation.
RESTORING FACTORY DEFAULT SETTINGS
The One For All 3 Device Universal Remote Control also contains a Factory Reset program that you can use to reset all custom settings and setup codes to original factory settings.Also see Clearing Custom Programming above.
IMPORTANT: Executing this program will erase all your custom settings for Power Macro, Favorite Channels, Volume Lock, Reassigned Devices, and all device settings.
Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 8 - 1. The LED will blink twice. The remote control will return to normal operation.

Page 15

TROUBLESHOOTING
PROBLEM: SOLUTION: PROBLEM: SOLUTION:
LED (red light) does not blink when you press a key.
Replace batteries with two new AAA alkaline batteries.
LED blinks when you press a key, but home entertain-
ment device does not respond. Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. The unit does not control home entertainment devices or commands are not working properly. Try all listed codes for the device brands being set up. Make sure they can be operated with an infrared remote control. Changing channels does not work. If original remote required pressing ENTER or SELECT to change channels,press ENTER or SELECT on this remote after entering the channel number. Tried Searching For Your Code method and still could not find a working code. Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Next enter 9 - 9 - 2. Then press the device key to be cleared twice. Now repeat the Searching For Your Code method on page 9.

CH L and CH M do not work for your RCA TV.

PROBLEM: SOLUTION:

Due to RCA design (1983-1987), only the original remote control will operate these functions. No remote control of volume. See Changing Volume Lock on page 12 to lock/unlock volume.
For assistance, please contact us in any of the following ways: E-mail: ofasupport@ueic.com Internet: http://www.oneforall.com Consumer Help Line: (330) 405-8612

INSTRUCTIONS TO THE USER

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase separation between equipment and receiver. Connect equipment into an outlet or a circuit different from that to which the receiver is connected. Consult dealer or experienced radio/TV technician for help. 15

Page 16

LIFETIME WARRANTY
One For ALL ("OFA") warrants this product to be free from defects in materials and workmanship, under normal use, throughout the period of the products ownership by the original purchaser. This warranty does not cover damages or failures caused by products or services not supplied by OFA, or which result from accident, misuses, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God. There are no express warranties except as listed above. OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY,ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damagers, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase for the first 90 days.A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. If the unit has been purchased more than 90 days ago, please return it to CT Global Inc. 8918 Stone Green Way, Louisville, KY 40220 together with the original receipt and $3.95 to cover postage and handling. It will be repaired or replaced at the manufacturers option. The manufacturer reserves the right to substitute a currently manufactured model with equal or superior features. One For All: (330) 405-8655 URC-3021 March 2004

Page 17

ADDITIONAL INFORMATION
As you update your home entertainment system, One For All has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you: One For All Access 3. URC-3605 One For All Big Easy 3-Device. URC-3300 One For All DVD Expert 4-Device. URC-4041 One For All Big Easy 4-Device. URC-4330 One For All Access 4. URC-4605 One For All Access 5. URC-5705 One For All 4 Device. URC-4021 One For All 3 Device. URC-3021 One For All PVR 6-Device. URC-6131 One For All 6-Device Home Theater. URC-6011 One For All 8-Device Home Theater. URC-8011 One For All 8L-Device Home Theater With Learning. URC-8811 One For All A/V LCD 8 Device With Learning. URC-8910 One For All IR/RF LCD 8 Device With Learning. URC-9910 One For All 8 Device Home Theater Remote Powered By Kameleon. URC-9960 ONE FOR ALL is the registered trademark of Universal Electronics Inc. Computime International Ltd. is the Licensee of the ONE FOR ALL brand for USA and Canada. Copyright 2004 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc. The One For All 3 Device Universal Remote Control is compatible for use in North America, excluding Mexico. This One For All 3 Device Universal Remote Control is covered by one or more of the following US Patents: 6,587,067 6,587,067 6,496,135 5,481,256 5,515,052 5,959,751

Page 18

MANUFACTURERS CODES
Setup Codes for Cable Boxes
Americast Bell South Director GoldStar Hamlin Jerrold Memorex Motorola Pace Panasonic Paragon 0009 0476, 0810, 0476, 0810, 0000, Philips Pioneer Pulsar Quasar Runco Samsung Scientific Atlanta Sony Supercable Toshiba Zenith 0305, 0317 0877, 1877, 0144, 0144 0877, 1877, 0000, 0525, 0899
General Instrument 0476, 0810, 0276
Setup Codes for Cable Box/PVR (or DVR) Combos
Motorola Pioneer Scientific Atlanta 1877
Setup Codes for DVD Players
Apex Digital Axion Blaupunkt Blue Parade CineVision Curtis Mathes CyberHome Daewoo Denon Dual DVD2000 Emerson Enterprise Fisher Funai GE Go Video GPX Greenhill Hitachi Hiteker JVC Kenwood KLH Koss Lasonic Magnavox Marantz Microsoft 0672, 0717, 0794, 1056, 0755, 0797, 1100, 0796, 1024, 1023, 0521 0591, 0522, 0815, 0717 0744, 0715, 0672 0558, 0623 0490, 0534 0717, 0798 0503, 0522 Mintek Mitsubishi Nesa Norcent Onkyo Oritron Panasonic Philips Pioneer Polk Audio Proscan Qwestar RCA Rotel Rowa Samsung Sanyo Shinsonic Sony Sylvania Symphonic Technics Theta Digital Toshiba Tredex Urban Concepts Xbox Yamaha Zenith 0839, 0717 0521, 0651 0490, 1762 0503, 0539, 0646 0525, 0522, 0571, 0823 0573, 1075, 0533, 0839 0533, 1533, 0864, 0522 0490, 0539, 0545 0503, 0591

Setup Codes For DVD Player/VCR Combos
Apex Digital Go Video Hitachi Panasonic RCA Samsung 1061 0744, 1075, 0820 Sanyo Sony Sylvania Symphonic Toshiba 0675, 0000 0675, 0000 0503

Page 19

Setup Codes for PVRs (or DVRs)
Panasonic Philips ReplayTV 0614, 0616 Sonic Blue Sony Tivo 0616, 0636, 0618
Setup Codes for Satellite Receivers
AlphaStar DirecTV 0772 0392, 0566, 0639, 0247, 0749, 1749, 0724, 0819, 1856 1005, 0775 1005, 0749, 0724, Mitsubishi Motorola Next Level Panasonic Paysat Philips Proscan RadioShack RCA Samsung SKY Sony Star Choice Toshiba UltimateTV Uniden Zenith 0869 0247, 0749, 1749, 0724, 0722 0392, 0392, 0566, 0855, 0856 0639, 0749, 1749, 0790, 1285 0392, 0639 0724, 0722 0856, 1856
Dish Network System 1005, 0775 Dishpro Echostar Expressvu GE GOI Hitachi HTS Hughes Network Systems JVC Magnavox Memorex

General Instrument 0869

Setup Codes for Satellite Receiver/PVR (or DVR) Combos
Echostar Expressvu Proscan 0392 RCA Sony 0392 0639

Setup Codes for TVs

AOC Admiral Advent Aiko Akai Alfide America Action Anam Apex Digital Audiovox Baysonic Bell & Howell Bradford Broksonic CXC Candle Carnivale Carver Celebrity Celera Changhong Cineral Citizen Clarion Contec Craig Crosley Crown 0030 0093, 0463 0761, 0702, 0030, 0672, 0748, 0765, 0767 0451, 0180, 0092, 0236, 0451, 0092 0060, 0030, 0054 0180, 0672 Daewoo Denon Dumont Durabrand Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gateway Gibralter GoldStar Gradiente Grundig Grunpy Hallmark Harman/Kardon Harvard Havermy Hello Kitty Crown Mustang Curtis Mathes 0672 0047, 0054, 0154, 0451, 0093, 0060, 0702, 0030, 0145, 0166, 1147, 1347 0451, 1661, 0092, 0672, 0017 0178, 0154, 0236, 0463, 0180, 0178, 0171, 0154 0683, 0809 0180, 0047, 0051, 0451, 0178, 1147, 1347 1755, 1756 0017, 0030 0030, 0451

Page 20

Hitachi Infinity Inteq JBL JCB JVC Jensen KEC KLH KTV Kenwood Kioto LXI MGA MTC Magnavox Marantz Matsushita Megatron Memorex Midland Mitsubishi Motorola Multitech NAD NEC NTC Nikko Norcent Onwa Optimus Optonica Orion Panasonic Penney Philco Philips Pilot Pioneer Portland Prima Prism Proscan Proton Pulsar Quasar
0145, 0000 0463, 0180 0765, 0767 0180, 0706 0047, 0054, 0154, 0156, 0178 0150, 0030, 0178 0060, 0030 0054, 0706, 0030, 1454, 1254 0054, 0030 0250, 0650 0178, 0145 0154, 0250, 0463, 0150, 0178 0047, 0017, 0051 0093, 0150, 1250, 0178, 0180 0156, 0178, 0866 0030, 1704, 0030, 0178, 0092 0748, 0154, 0250, 0166, 0236, 0463 0051, 0250, 0650 0047, 0156, 0051, 0060, 0030, 0178, 1347 0054, 1661, 0463, 0030, 0145 0054, 1454, 0166, 0017 0051, 0250, 0650
RCA RadioShack Realistic Runco SSS Sampo Samsung Sansei Sansui Sanyo Scotch Scott Sears Semivox Semp Sharp Sheng Chia Sony Soundesign Squareview Starlite Supreme Sylvania Symphonic TMK TNCi TVS Tandy Technics Techwood Teknika Telefunken Toshiba Toshiba Vector Research Victor Vidikron Vidtech ViewSonic Wards Waycon Yamaha Zenith

Shogun Singer Sonic Blue Sony STS Sylvania Symphonic Tagar Systems Tatung Teac Technics Teknika Thomas Tivo TMK Toshiba Totevision Touch Unitech Vector Vector Research Video Concepts Videomagic Videosonic Viewsonic Villain Wards
0614, 0616 0035, 0032, 0033, 0000, 1232, 0035, 0081, 0000, 0043, 0000, 0041 0035, 0162 0035, 0037, 0636, 0045, 0043, 1145, 0845 0037, 0060, 0035, 0048, 0047, 0081, 0240, 0000, 0042, 0072 0035, 0000, 0039, 0033, 0000, 0209, 1479, 0479 1972
White Westinghouse 0209, 0072 XR-1000 Yamaha Zenith ZT Group