Important Safety Information
Before using your navigation system, be sure to read and fully understand the following safety information: Read the entire manual before operating this navigation system. The navigation features of this product (and rear view camera option if purchased) is intended solely as an aid to you in the operation of your vehicle. It is not a substitute for your attentiveness, judgment, and care when driving. Do not operate this navigation system (or the rear view camera option if purchased) if doing so in any way will divert your attention from the safe operation of your vehicle. Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty in operating the system or reading the display, park your vehicle in a safe location and apply the parking brake before making the necessary adjustments. Never allow others to use the system unless they have read and understood the operating instructions. Never use this navigation system to route to hospitals, police stations, or similar facilities in an emergency. Please call 911. Route and guidance information displayed by this equipment is for reference purposes only. It may not accurately reflect the latest permissible routes, road conditions, one way streets, road closures, or traffic restrictions. Traffic restrictions and advisories currently in force should always take precedence over guidance given by the navigation system. Always obey current traffic restrictions, even if the navigation system provides contrary advice. Failure to input correct information about the local time may result in the navigation system providing improper routing and guidance instructions. Never set the volume of your navigation system so high that you cannot hear outside traffic and emergency vehicles.
To promote safety, certain functions are disabled unless the vehicle is stopped and/or the parking brake is applied. The data encoded in the disc is the intellectual property of the provider, and the provider is responsible for such content. Keep this manual handy as a reference for operating procedures and safety information. Pay close attention to all warnings in this manual and follow the instructions carefully. Do not install the display where it may (i) obstruct the drivers vision, (ii) impair the performance of any of the vehicles operating systems or safety features, including air bags, hazard lamp buttons or (iii) impair the drivers ability to safely operate the vehicle. Please remember to wear your seat belt at all times while operating your vehicle. If you are ever in an accident, your injuries can be considerably more severe if your seat belt is not properly buckled. Using the most current DVD Map Discs will allow for most accurate destination mapping. Upgrade DVD Map Discs are available for purchase through your local Pioneer dealer. Never use headphones while driving.

To avoid the risk of accident and the potential violation of applicable laws, this product should never be used while the vehicle is being driven except for navigation purposes. Also, Rear Displays should not be in a location where it is a visible distraction to the driver. In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and the products visual image features should not be used. Visual image in this manual indicates the moving image from the equipments which are connected to this product with AV-BUS or RCA cable, such as DVD player and TV tuner. This product detects whether your vehicles parking brake is engaged or not, and prevents you from watching visual images on the front display while driving. When you attempt to watch visual images, the warning Viewing of front seat video source while driving is strictly prohibited. will appear on the front display. To watch visual images on the front display, park your vehicle in a safe place and apply the parking brake. See Parking brake interlock in the Operation Manual for more information.
Do not use with vehicles that do not feature an ACC position.

About rear view camera

With an optional rear view camera (sold separately) you are able to use the navigation system as an aid to keep an eye on trailers, or while backing up.
SCREEN IMAGE MAY APPEAR REVERSED. USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
When using a display connected to REAR OUT
This procucts REAR OUT is for connection of a display to enable passengers in the rear seats to watch visual imeges. The map screen navigation images output to the rear display differs from standard NTSC format images. Therefore, the quality will be inferior to the images that appear on the front display.
The rear view camera function is to be used as an aid to keep an eye on trailers, or while backing up. Do not use for entertainment purposes. Please note that the edges of the rear view camera images may differ slightly according to whether full screen images are displayed when backing up, and whether the images are used for checking the rear when the vehicle is moving forward.
NEVER install the rear display in a location that enables the driver to watch visual images while driving.
After-sales service for Pioneer products
Please contact the dealer or distributor from where you purchased the product for its aftersales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your product to the companies at the addresses listed below for repair without making advance contact. U.S.A CANADA Pioneer Electronics of Pioneer Electronics Canada, Inc. (USA) Inc. CUSTOMER CUSTOMER SATISFACTION SUPPORT DIVISION P.O. Box 1760 DEPARTMENT 300 Allstate Parkway Long Beach, CA 90801-1760 Markham, Ontario 800-421-1404 L3R OP2 1-877-283-5901 For warranty information, please see the Limited Warranty sheet included with your product.

Upgrade DVD Map Disc

Upgrade DVD Map Discs are available for purchase from your local Pioneer dealer. These includes the most current map and point of interest information. Contact your local Pioneer dealer for details.

Playable discs

About DVD-Video and CD
DVD and CD discs that display the logos shown below generally can be played back on this builtin DVD drive. DVD-Video

Product registration

Visit us at the following site: is a trademark of DVD Format/Logo Licensing Corporation.
1. Register your product. We will keep the details of your purchase on file to help you refer to this information in the event of an insurance claim such as loss or theft. 2. Receive updates on the latest products and technologies. 3. Download owners manuals, order product catalogues, research new products, and much more. 4. Receive notices of software upgrades and software updates.
It is not possible to play back DVD audio discs. This DVD drive may not be able to play all discs bearing the marks shown above.

About DVD Map Disc

You can use discs intended for this navigation system. Use only discs approved by Pioneer. For details on other discs Page 18
DVD-Video disc region numbers
DVD-Video discs that have incompatible region numbers cannot be played on this DVD drive. The region number of the player can be found on the bottom of this product. The illustration below shows the regions and corresponding region numbers.

MP3 file playback

It is possible to play back MP3 files recorded on CD-ROM/CD-R/CD-RW (ISO9660 Level 1/Level 2 standard recordings). Supply of this navigation system only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com. Handling and Care of the Disc Page 18 Playable discs Page 6
Features (Characteristics of this hardware)
Touch panel key operation
It is possible to operate this product by using touch panel keys.

NTSC compatibility

This product is NTSC system compatible. When connecting other components to the product, be sure components are compatible with the same video system or else images will not be correctly reproduced.
Built-in Navigation system
You can use DVD Map Discs that are compatible with this system.

What the Marks on DVDs Indicate
The marks below may be found on DVD disc labels and packages. They indicate the type of images and audio recorded on the disc, and the functions you can use.
Meaning Indicates the number of audio systems. Indicates the number of subtitle languages. Indicates the number of viewing angles.

: 9 LB

Indicates the picture size (aspect ratio: screen width-to-height ratio) type. Indicates the number of the region where playback is possible.
If the marks other than listed are found on DVD disc labels and packages, please ask for the DVD disc supplier for their meaning.
Turn the ignition switch OFF. Press the RESET button with a pen tip or other pointed instrument.
When an operation is prohibited
When you are watching a DVD and attempt to perform an operation, sometimes it may not be performed because of the programming on the disc. When this happens, this product indicates the icon on the screen. The icon may not appear in certain discs.

RESET button

Resetting the Microprocessor
Pressing the RESET button deletes the contents of the navigation systems memory. For details, see section About the Data being Deleted of the Operation Manual. Pressing the RESET button lets you reset the microprocessor to its initial settings without changing the condition memory. The microprocessor must be reset under the following conditions: Prior to using this product for the first time after installation. If the product fails to operate properly. If there appear to be problems with the operation of the system. When changing the combination of the equipment. When adding/removing additional products that connect to this product. When the display and the Hide-away units are re-connected.
If you have connected other equipment (for example, a TV tuner) to this navigation system, be sure to reset that equipment too. After completing connections or when you want to erase all memorized settings or return this product to its initial (factory) settings except for some navigation items, switch your engine ON or set the ignition switch to ACC ON before pressing the RESET button. For details, refer to About the Data being Deleted in the Operation Manual.

Display unit

This section gives information about the names of the parts and main features using the buttons. For more detail operation, functional limitations, please refer to the Operation Manual.

l k j i h

1 DISP button Press to select different displays. 2 BAND button Radio: Press to select among three FM and one AM bands.
Built-in DVD drive: When playing back a disc containing an MP3 file and audio data (CD-DA), pressing this button switches playback between the MP3 file and CDDA. Touch and hold this button when a disc containing an MP3 file is inserted returns you to the root folder. 11

3 Sub display

Current time or the information of the audio source currently playing is displayed when the LCD panel is closed. Senses ambient light. This system automatically adjusts the brightness of the display to compensate for ambient light. Press to turn the LCD panel horizontal temporarily when the LCD panel is upright. Press to turn the clock of the sub display on or off when the LCD panel is closed. Press to open or close the LCD panel. Use to switch between Navigation map displays and audio operation displays.

f TRFC button

4 Ambient light sensor

5 FLIP DOWN/CLOCK button

When the XM tuner is connected*: Preset button for XM Instant Traffic & Weather audio service. Select XM audio source, and find appropriate Instant Traffic & Weather channel. Hold down this button while on this channel to assign preset. When the XM tuner is not connected: Not used. XM tuner (GEX-P10XMT, GEX-P920XM) Operation Manual

g ANGLE (+/) button

Press to change the LCD panel angle.
6 OPEN/CLOSE button 7 NAVI/AV button

h WIDE/PIC ADJ button

Press to select a desired mode for enlarging a 4:3 picture to a 16:9 one. Press and hold to enter the PICTURE ADJUSTMENT mode. See Changing the Wide Screen Mode and Operating the Picture Adjustment in the Operation Mannual.

8 POS button

Press to view the map or return to guidance. Also, when the map is scrolling, pressing this button returns you to the display of the map of your surroundings. Use to switch the view mode of the navigation when the map of your surroundings is displayed. Press to display a menu of Navigation. Press to return to the factory settings (initial settings). Some information items are not erased. Resetting the microprocessor Page 10

i REAR/GUIDE button

9 NAVI MENU button a RESET button
Press to output to the REAR OUT terminal the sound and images of a disc inserted in the builtin DVD drive that is different the currently selected source. Using the REAR/GUIDE Button Page 14 Press and hold to display the Volume setting screen. On the Volume setting screen, Guidance Volume, Beep Volume, and Mute Settings can be set. Guidance Volume, Beep Volume, Mute Settings See Volume in the Operation Manual

b DETACH button

Press to remove the front panel from the display unit. Move to do manual seek tuning, fast forward, reverse and track search controls, etc. Push to display A.MENU. Press to select various equalizer curves. Press to eject a disc from this product.

c Joystick

j MEMO button

d EQ button

e EJECT button
When the XM tuner is connected and the XM source is selected*: Press and hold this button to memorize the track currently being played. The beep sounds and a message is displayed when the memorized track is playing on a station other than the one which you are currently on. If you press this button while the message is displayed, the station changes to the one playing your track.
When the XM tuner is not connected: Not used. XM tuner (GEX-P10XMT, GEX-P920XM) Operation Manual
k Disc loading slot Insert a disc to play.

Loading a Disc Page 14

l SRC (SOURCE) button This product is turned on by selecting a source. Press to cycle through all of the available sources. Press and hold to turn the source off. m VOLUME/ATT button Rotate to increase or decrease the volume. Press to quickly lower the volume level, by about 90%. Press once more to return to the original volume level. n LCD panel o LCD screen p Front panel
*: GEX-P10XMT or GEX-P920XM sold separately is required, in addition to an active subscription to XM Satellite Radio service.
Press the SRC button to select a source. Press the SRC button repeatedly to switch between the following sources: XM (XM tuner) SIRIUS (SIRIUS tuner) RADIO (tuner) TV (television) AV (video input) DISC [CD, MP3, CD/ MP3](built-in DVD drive) S-DVD (DVD player/multi-DVD player) M-CD (multi-CD player) iPod (iPod) EXT-1 (external unit 1) EXT-2 (external unit 2) AUX (Auxiliary equipment) Press and hold to turn the source off.
In the following cases, the sound source cannot be used: When a unit corresponding to each source is not connected to this product. When no disc (DVD-Video, CD) is set in this product. When no disc is set in the DVD-player (SDVD). When no magazine is set in the multi-CD player. When no magazine is set in the multi-DVD player. When the AUX (auxiliary input) is set to off (refer to Operation Manual). When the AV (video input) is not set to VIDEO (refer to Operation Manual). External unit refers to a Pioneer product (such as one available in the future) that, although incompatible as a source, enables control of basic functions by this product. Two external units can be controlled by this product. When two external units are connected, the allocation of them to external unit 1 or external unit 2 is automatically set by this product. When this products blue lead is connected to the vehicles auto-antenna relay control terminal, the vehicles antenna extends when ACC (ignition) is turned on and attach the front panel. To retract the antenna, detach the front panel. The vehicles antenna extends regardless of turning this products source on or off.
Turning the Navigation System On and Selecting a Source
If the program is not installed, see Operation Manual and install the program.
Turn the ignition switch (ACC) ON. The navigation systems power supply comes on.

Loading a Disc

Insert a disc into the disc loading slot. Format reading will start. For DVD-Video, CD DISC AUTO is off in the default setting. DISC AUTO Operation Manual When a disc is already loaded in this product, select the source by pressing the SRC button. To eject a disc, press the EJECT button. For the DVD Map Disc Inserting the Disc starts DVD navigation mode. Removing the Disc sets Memory navi mode. You can use the NAVI/AV button to switch between navigation map displays and audio operation displays. The DVD drive plays one, standard, 12-cm or 8-cm (single) disc at a time. Do not use an adapter when playing 8-cm discs. Do not insert anything other than a disc into the disc loading slot. Playable discs Page 6 If you cannot insert a disc completely or if after you insert a disc the disc is not recognized, check that the label side of the disc is up. Press the EJECT button to eject the disc, and check the disc for damage before inserting the disc again. If the DVD drive does not operate properly, an error message such as ERROR-11 may be displayed. Error messages Operation Manual

Turning the Source Off

Press the SRC button and hold until the source turns off. This product can be switched off by turning the ACC (ignition) OFF or detaching the front panel.
Using the REAR/GUIDE Button
You can output the sound and video of the disc in the built-in DVD drive to the rear display regardless of whether DVD drive is selected as the source or not (REAR ON mode).
When you have turned the REAR ON mode on by pressing the REAR/GUIDE button, you cannot turn it off even if you press the SRC button and hold. In this case, press the REAR/GUIDE button to turn the REAR ON mode off. Press the REAR/GUIDE button to turn the REAR ON mode. The sound and video are output to the rear display and the illumination color of the GUIDE/REAR button changes to red. To turn the REAR ON mode off, press the REAR/GUIDE button again. When a CD or CD-ROM is inserted, sound only is output to the rear display. Selecting the video of rear display Operation Manual

Opening and Closing the LCD Panel

Adjusting the Volume

Use the VOLUME/ATT button to adjust the audio sound level. With this product, rotate the VOLUME/ATT button to increase or decrease the volume. To adjust the navigation volume, go to the navigation menu. Navigation volume adjustment Operation Manual 14 Do not close the LCD panel with hands by force. This may cause malfunction. The LCD panel will be opened or closed automatically with the turning of the ignition switch on or off. You can turn off the automatic close/open function. Setting the automatic close/open function Operation Manual
The automatic close/open function will operate the display as follows. When the ignition switch is turned OFF while the LCD panel is open, the LCD panel will close after six seconds. When the ignition switch is turned ON again (or turned to ACC), the LCD panel will open automatically. Removing or attaching the front panel will automatically close or open the LCD panel. Removing the front panel Page 16 When the ignition switch is turned OFF after the LCD panel has been closed, turning the ignition switch ON again (or turning it to ACC) will not open the LCD panel. In this case, press the OPEN/CLOSE button to open the LCD panel. When closing the LCD panel, check to make sure that it has closed completely. If the LCD panel has stopped halfway, leaving it like this could result in damage. Press the OPEN/CLOSE button to open the LCD panel. To close the LCD panel, press the OPEN/ CLOSE button again.
The adjusted the LCD panel angle will be memorized and the LCD panel will automatically return to this angle the next time the LCD panel is opened.
Turning the LCD panel horizontal
When the LCD panel is upright and it hinders the operation of the air conditioner, the position of the panel can be turned horizontal temporarily. Press the FLIP DOWN/CLOCK button to turn the LCD panel horizontal. To return to original position, press the FLIP DOWN/CLOCK button again. The LCD panel returns to the original position automatically with beep sounds 10 seconds after operation.
Adjusting the LCD panel angle
Important: If you can hear the LCD panel knocking against your vehicles console or dashboard, press the ANGLE () button to move the LCD panel a little forward. When adjusting the LCD panel angle, be sure to press the ANGLE (+/) button. Forcibly adjusting the LCD panel by hand may damage it. Press the ANGLE (+/) button to adjust the LCD panel to an easily viewable angle. The LCD panel angle continues changing as long as you press the ANGLE (+/) button and hold.
Protecting Your Product from Theft
The front panel can be detached from the display unit to discourage theft, as described below. Important: Never use force or grip the display and the buttons tightly when removing or attaching. Avoid subjecting the front panel to excessive shocks. Keep the front panel out of direct sunlight and high temperatures. After detaching the front panel, keep it in the safe place not to result in scratching or damage. Attach the front panel while driving, or else may result in scratching or damage.

Removing the front panel

Press the DETACH button to remove the front panel. Gently grip the right side of the front panel and slowly pull it outward. Take care not to drop the front panel and protect it from contact with water or other fluids to prevent permanent damage.
Attaching the front panel
Replace the front panel by holding it upright to this product and clipping it securely into the mounting hooks.

Troubleshooting

About troubleshooting other than description below Appendix of the Operation Manual
Symptom No picture. Cause The parking brake cord is not connected. The parking brake is not applied. The picture is stretched, the aspect is incorrect. Rear display picture disappears. The aspect setting is incorrect for the display. The source disc being listened to with the navigation system has been ejected. The REAR/GUIDE button was pressed and REAR ON mode switched off. There was a problem with the rear display or a faulty wiring connection, for example. Rear View is selected on the screen. When the shift lever is in [R], displays rear view camera images. (When NAVI is selected in REAR DISP menu.) The source without a video is selected. Operating the PICTURE ADJUSTMENT. Nothing is displayed and the touch panel keys cannot use. Action (See) Connect a parking brake cord, and apply the parking brake. Connect a parking brake cord, and apply the parking brake. Select the appropriate setting for your display. ( Changing the Wide Screen Mode and Operating the Picture Adjustment in the Operation Mannual.) Before ejecting the disc, switch the source. This problem may occur when certain connection methods are used. Press the REAR/GUIDE button to turn REAR ON mode on. Check the rear display and its connection.
Adjusting the volume of navigation guidance and beep is not possible. Playback is not possible.
LCD Panel knocking against your vehicles console or dashboard. Video image appears grainy.
Select view mode other than Rear View. Move the shift lever other than turn [R] position. (Select SOURCE in REAR DISP menu.) Switch the source with a video. There is no picture on the rear display while the PICTURE ADJUSTMENT is carried out. The setting for the rear view camera is Connect a rear view camera correctly. incorrect. Press the NAVI/AV button to return to the The shift lever was placed in [R] when the source display and then select the correct rear view camera was not connected. setting for CAMERA. About CAMERA setting Operation Manual You cannot adjust them with the VOLUME/ Turn the volume up or down according to ATT button. Volume in the Setting menu. Press the REAR/GUIDE button ond turn the volume up or down. The disc is dirty. Clean disc. The loaded disc is a type your navigation Check what type the disc is. ( Page 18) system cannot play. Non compatible video system disc is Change to a disc compatible to your video loaded. system. ( Page 18) The loaded disc has a different region num- Replace the disc with one featuring the ber from the navigation system. same region number as the navigation system. ( Page 7) Incorrect setting of angle. Press the ANGLE (+/) button to adjust the LCD angle. Forcibly adjusting the LCD panel by hand may damage it. This happens when videos are viewed in Select a different mode to view videos. CINEMA or ZOOM mode.

Check all discs for cracks, scratches or warping before playing. Discs that have cracks, scratches or are warped may not play properly. Do not use such discs. Avoid touching the recorded (non-printed side) surface when handling the disc. Store discs in their cases when not in use. Keep discs out of direct sunlight and do not expose the discs to high temperatures. Do not attach labels, write on or apply chemicals to the surface of the discs. To clean dirt from a disc, wipe the disc with a soft cloth outward from the center of the disc. 18
It is not possible to play back DVD-ROM discs other than Pioneer DVD map disc or DVD-RAM discs. Playback of discs recorded on a personal computer may not be possible depending on the application settings and the environment. Please record with the correct format. (For details, contact the manufacturer of the application.)

CD-R/CD-RW discs

When CD-R/CD-RW discs are used, playback is possible only for discs which have been finalized. It may not be possible to playback CD-R/CDRW discs recorded on a music CD recorder or a personal computer because of disc characteristics, scratches or dirt on the disc, or dirt, condensation, etc. on the lens of this product. Playback of discs recorded on a personal computer may not be possible, depending on the application settings and the environment. Please record with the correct format. (For details, contact the manufacturer of the application.) Playback of CD-R/CD-RW discs may become impossible in case of direct exposure to sunlight, high temperatures, or the storage conditions in the vehicle. Titles and other text information recorded on a CD-R/CD-RW disc may not be displayed by this product (in the case of audio data (CD-DA)). If you insert a CD-RW disc into this product, time to playback will be longer than when you insert a conventional CD or CD-R disc. Read the precautions with CD-R/CD-RW discs before using them.

MP3 files

Important: When naming an MP3 file, add the corresponding filename extension (.mp3). This product plays back files with the filename extension (.mp3) as MP3 files. To prevent noise and malfunctions, do not use this extension for files other than MP3 files. MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. This product allows playback of MP3 files on CD-ROM, CD-R and CD-RW discs. Disc record-
ings compatible with level 1 and level 2 of ISO9660 and with the Romeo and Joliet file system can be played back. It is possible to play back multi-session compatible recorded discs. MP3 files are not compatible with packet write data transfer. The max. number of characters which can be displayed for a file name, including the extension (.mp3), is 30 characters from the first character. The max. number of characters which can be displayed for a folder name is 30 characters. In case of files recorded according to the Romeo and Joliet file system, only the first 30 characters can be displayed. Depending on the width of the characters, the screen may not be able to display 30 characters. When playing discs with MP3 files and audio data (CD-DA) such as CD-EXTRA and MIXEDMODE CDs, both types can be played only by switching mode between MP3 and CD-DA. The folder selection sequence for playback and other operations becomes the writing sequence used by the writing software. For this reason, the expected sequence at the time of playback may not coincide with the actual playback sequence. However, there also is some writing software which permits setting of the playback order. Some audio CDs contain tracks that merge into one another without a pause. When these discs are converted to MP3 files and burned to a CD-R/CD-RW/CD-ROM, the files will be played back on this player with a short pause between each one, regardless of the length of the pause between tracks on the original audio CD. Files are compatible with the ID3 Tag Ver. 1.0 and Ver. 1.1 formats for display of album (disc title), track (track title) and artist (track artist). The emphasis function is valid only when MP3 files of 32, 44.1 and 48 kHz frequencies are played back. (16, 22.05, 24, 32, 44.1, 48 kHz sampling frequencies can be played back.) There is no m3u playlist compatibility. There is no compatibility with the MP3i (MP3 interactive) or MP3 PRO formats.

Keeping the LCD screen in good condition
When removing dust from the LCD screen or cleaning the LCD screen, first turn the system power off, then wipe with the supplied cloth. When wiping the LCD screen, take care not to scratch the surface. Do not use harsh or abrasive chemical cleaners.

Glossary

Glossary Appendix of the Operation Manual

Small fluorescent tube

A small fluorescent tube is used inside the display to illuminate the LCD screen. The fluorescent tube should last for approximately hours, depending on operating conditions. (Using the display unit at low temperatures reduces the service life of the fluorescent tube.) When the fluorescent tube reaches the end of its useful life, the LCD screen will be dark and the image will no longer be projected. If this happens, consult your dealer or the nearest authorized PIONEER Service Station.

Specifications

General Rated power source. 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system.. Negative type Max. current consumption.. 10.0 A Display unit: Dimensions (W H D): DIN Chassis.. 160 mm (6-1/4 in.) Nose.. 34 mm (7-3/8 2-1/4 1-3/8 in.) D Chassis.. 165 mm (6-1/2 in.) Nose.. 29 mm (6-3/4 1-3/4 1-1/4 in.) Weight. 2.5 kg(5.5 lbs) Hideaway unit: Dimensions (W H D).. 140 mm (5-7/8 1-1/8 3-7/8 in.) Weight. 0.7 kg(1.5 lbs) Navigation GPS Receiver: System. L1, C/Acode GPS SPS (Standard Positioning Service) Reception system. 8-channel multi-channel reception system Reception frequency. 1 575.42 MHz Sensitivity. 130 dBm Position update frequency.. Approx. once per second GPS antenna: Antenna. Micro strip flat antenna/ right-handed helical polarization Antenna cable. 5.0 m(16 ft. 5 in.) Dimensions (W H D).. 36 mm (1-1/4 1/2 1-3/8 in.) Weight. 105 g(0.23 lbs) Display Screen size/aspect ratio. 6.5 inch wide/16:9 (effective display area: mm) Pixels. (234) Type.. TFT active matrix, transmissive type Color system. NTSC Operating temperature range.. +14 F to +122 F Storage temperature range.. 4 F to +176 F Angle adjustment. 50 to 110 (initial settings: 110)
Audio Continuous power output is 22 W per channel minimum into 4 ohms, both channels driven 50 to Hz with no more than 5% THD. Maximum power output.. 50 W W 2 ch/4 + 70 W 1 ch/2 (for subwoofer) Load impedance. 4 (4 to 8 [2 for 1 ch] allowable) Preout max output level/output impedance.. 2.0 V/100 ohm Equalizer (3-Band Parametric Equalizer): Low Frequency. 40/80/100/160 Hz Q Factor. 0.35/0.59/0.95/1.15 (+6 dB when boosted) Gain.. 12dB Mid Frequency. 200/500/1k/2k Hz Q Factor. 0.35/0.59/0.95/1.15 (+6 dB when boosted) Gain.. 12dB High Frequency. 3.15k/8k/10k/12.5k Hz Q Factor. 0.35/0.59/0.95/1.15 (+6 dB when boosted) Gain.. 12dB Loudness contour: Low. +3.5 dB (100 Hz), +3 dB (10 kHz) Mid.. +10 dB (100 Hz), +6.5 dB (10 kHz) High.. +11 dB (100 Hz), +11 dB (10 kHz) (volume: 30 dB) Tone controls: Bass Frequency. 40/63/100/160 Hz Gain.. 12dB Treble Frequency. 2.5k/4k/6.3k/10k Hz Gain.. 12dB HPF: Frequency.. 50/80/125 Hz Slope.. 12 dB/oct Subwoofer: Frequency.. 50/80/125 Hz Slope.. 18 dB/oct Gain.. 12dB Phase.. Normal/Reverse DVD Drive System.. DVD-Video, Compact disc audio, MP3 system Usable discs. DVD-Video, Compact disc, MP3 Region number.. 1 Signal format: Sampling frequency. 44.1/48/96 kHz Number of quantization bits.. 16/20/24; linear

Frequency response. 5 Hz to Hz (with DVD, at sampling frequency 96 kHz) Signal-to-noise ratio. 97 dB (1 kHz) (IHF-A network) (CD: 96 dB (1 kHz) (IHF-A network)) Dynamic range.. 95 dB (1 kHz) (CD: 94 dB (1 kHz)) Distortion.. 0.008 % (1 kHz) Output level: Video.. 1.0 Vp-p/75 (0.2 V) Audio.. 1.0 V (1 kHz, 0 dB) Number of channels. 2 (stereo) MP3 decoding format.. MPEG-1 & 2 Audio Layer 3 FM tuner Frequency range. 87.9 MHz to 107.9 MHz Usable sensitivity.. 8 dBf (0.7 V/75 , mono, S/ N: 30 dB) 50 dB quieting sensitivity. 10 dBf (0.9 V/75 , mono) Signal-to-noise ratio. 75 dB (IHF-A network) Distortion.. 0.3 % (at 65 dBf, 1 kHz, stereo) 0.1 % (at 65 dBf, 1 kHz, mono) Frequency response. 30 Hz to Hz (3 dB) Stereo separation. 45 dB (at 65 dBf, 1 kHz) Selectivity.. 80 dB (200 kHz) Three-signal intermodulation (desired signal level).. 30 dBf (two undesired signal level: 100 dBf) AM tuner Frequency range. 530 kHz to kHz (10 kHz) Usable sensitivity.. 18 V (S/N: 20 dB) Signal-to-noise ratio. 65 dB (IHF-A network)
Note: Specifications and the design are subject to possible modifications without notice due to improvements.

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Blvd.Manuel Avila Camacho piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL:55-9178-4270
Published by Pioneer Corporation. Copyright 2005 by Pioneer Corporation. All rights reserved.
<KYGHX> <05K00001>
Printed in China <CRB2147-A/U> UC

Hardware buttons

DVD MULTIMEDIA AV NAVIGATION SERVER

Search function overview

This navigation system has multiple methods for entering your destination.

(1) (2) (3) (4) (5)

Searching your destination by address
1 Press or touch in the following order. NAVI MENU button Destination tab Address Search

4 Select the street name

from list.

AVIC-N3

(3) (2) (1) (10) (4) (9) (8) (7) (6)(5) (6) (7) (8) (9)

Quick Start Guide

This guide is intended to guide you though the basic functions of this navigation system. For details, please refer to the Operation Manual and Hardware Manual provided with the product.

2 Input the house number

and then touch OK. When route calculation is complete, navigation guidance begins.
(1) NAVI/AV button Switch between navigation map displays and audio operation displays. (2) POS button Display the navigation map. (3) NAVI MENU button Access the navigation menu. (4) Joystick Use for operation of audio and video source. (5) EJECT button Press to eject a disc from the navigation system.
(6) TRFC button *1 Preset button for XM Instant Traffic & Weather audio service. (7) MEMO button *1 Press and hold for MyMix functionality. (8) SRC (SOURCE) button Press to toggle between audio sources. (9) VOLUME/ATT button Rotate to increase or decrease the volume. (10) Disc loading slot Insert a disc to play.

(1) (2) (3) (4)

Search by address Shortcut key for home address Shortcut key for favorite destination Search stores, restaurants, and other businesses in points of interest database (5) Search stores, restaurants, and other businesses in your vicinity
Search result list for vicinity search

3 Input the street name.

5 Begin driving in accordance with navigation guidance.
This navigation systems gives you route guidance both visually and by voice.
Published by Pioneer Corporation. Copyright 2006 by Pioneer Corporation. All rights reserved. <KYGHX> <06A00001>

(6) (7) (8) (9)

Select a destination from your address book Select a previously routed destination Select a route to freeway entrance or exit Search destination by business telephone number
Setting the voice guidance volume
Press or touch the following in order. NAVI MENU button Settings tab Volume
<CRB2248-A/U> UC Printed in China
*1 GEX-P10XMT XM Digital Satellite Data & Audio Receiver (sold separately) is required, together with an active subscription.

Switching the view mode

Press (POS) button. This navigation system allows you to select different view modes depending on your preference.
Traffic information on the map
Traffic conditions can be overlaid on the map when the optional GEX-P10XMT is connected, together with an active XM subscription. GEX-P10XMT XM Digital Satellite Data & Audio Receiver (sold separately) is required, together with an active subscription.

Changing the source

1 Touch the source icon and then select desired source.

Source icon

Operation of XM Satellite Radio
You can use the navigation system to control a XM satellite digital tuner. GEX-P10XMT XM Digital Satellite Data & Audio Receiver (sold separately) is required, together with an active subscription. (1) Shows detailed information of current song (2) Use to enter the channel number directly (3) Use to toggle between the following displays: Detail information display Ch Name List Song Title List Artist Name List
You can also press the SRC button to switch sources.

Scrolling the map

Touch where you would like to scroll to on the map screen. Tapping it once will activate the shortcut keys. Touching it a second time will begin map scroll. To scroll the map, keep touching the map. (1) Traffic event Stopped traffic Stop and go traffic Closed/blocked roads (2) Traffic flow The following items represent the traffic flow for the road. 5-15 mph (8-24 km/h) 20-40 mph (32-64 km/h) 45 mph or faster (72 km/h or faster) The icon indicates that the average speed of the road is over 45 mph (72 km/h).
Operation of the built-in DVD drive

1 Insert a disc.

Touch YES to begin the disc playback.

(1) (2) (3)

2 Adjust the volume. 3 Touch the screen to display
the touch panel keys for additional control.
Listening to your Apple iPod

4 Touch

You can control your iPod with Dock connector via the touch screen when it is connected to this navigation system via CD-IB100 iPod adapter.

Zoom in or zoom out

(1) (2)
Other event (e.g., accident)

Operating the DVD menu

1 Touch the screen to disM. to display the DVD menu.
play the touch panel keys.
(1) Direct scale change (2) Gradual scale change

2 Touch MENU or TOP

to display the touch panel keys to operate the DVD menu. select the desired menu item. playback.

5 Touch 5, , 2 or 3 to

CD-IB100 iPod adapter (sold separately) is required. (1) Touch to display the search categories.
Switching to the AV screen
1 Press the NAVI/AV button to change the screen. 3 Touch to display

6 Touch ENTER to start