For European Models

Declaration of Conformity
We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

PrecautionsContinued

This unit contains a semiconductor laser system and is classied as a CLASS 1 LASER PRODUCT. So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit. To prevent being exposed to the laser beam, do not try to open the enclosure.

Supplied Accessories

Make sure you have the following accessories:

DANGER:

VISIBLE AND/OR INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
Remote controller and two batteries (AA/R6)
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. The label on the right is applied on the rear panel.
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet. 2. To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualied personnel.
Indoor FM antenna (Connector type varies from country to country.)

AM loop antenna

Power cord (Plug type varies from country to country.)
* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specications and operations are the same regardless of color.

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualied service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Disc NotesContinued

The following ID3 tags are supported: versions 1.0/1.1 and 2.2/2.3/2.4. Versions 2.5 and later are not supported. Normally, version 2.2/2.3/2.4 tags have priority and will be displayed regardless of the ID3 VER 1 preference on page 37. For ID3 version 2 tags, the tag information recognized will be those embedded in the beginning of the le. We recommend that you include only title, artist name, and album name information in ID3 tags. Compressed, encrypted, and unsynchronized ID3 tags cannot be displayed. Note: With CD-ROM, CD-R, and CD-RW discs that contain many les and folders and les other than MP3s, it may take a long time to read the disc. We recommend that you include only MP3 les on your discs, use about 20 folders, and limit folder nesting to three levels deep. Cleaning Discs Disc Content Organization CD CDs contain tracks.
Track 1 Track 2 Track 3 Track 4 Track 5
Handling Discs Never touch the underside of a disc. Always hold discs by the edge, as shown.

Underside

Never attach adhesive tape or sticky labels to discs.
For best results, keep your discs clean. Fingerprints and dust can affect the sound quality and should be removed as follows. Using a clean soft cloth, wipe from the center outwards, as shown. Never wipe in a circular direction.

Audio CD

Folder 2 File 3 File 1 File 2
MP3 MP3 discs contain MP3 les organized into folders.

Folder 1 File 1 File 2

To remove stubborn dust or dirt, wipe the disc with a damp soft cloth, and then dry it with a dry cloth. Never use solvent-based cleaning uids, such as thinner or benzine, commercially available cleaners, or antistatic sprays intended for vinyl records, as they may damage the disc. Storing Discs Dont store discs in places subject to direct sunlight or near heat sources. Dont store discs in places subject to moisture or dust, such as in a bathroom or near a humidier. Always store discs in their cases and vertically. Stacking, or putting objects on unprotected discs may cause warping, scratches, or other damage.

MP3 (CD-R/CD-RW)

Connecting Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The CD receiver wont pick up any radio signals without an antenna connected, so you must connect the antenna to use the tuner.
AM antenna push terminals FM antenna jack
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use only.
Assemble the AM loop antenna, inserting the tabs into the base, as shown.
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown. North American Model
Connect both wires of the AM loop antenna to the AM push terminals, as shown. (The antennas wires are not polarity sensitive, so they can be connected either way around). Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
Insert the plug fully into the jack.

Other Models

Insert wire

Release

Once the CD receiver is ready for use, youll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Once the CD receiver is ready for use, youll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from the CD receiver, TV, speaker cables, and power cords. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 17).
Use thumbtacks or something similar to x the FM antenna into position.

Thumbtacks, etc.

Caution: Be careful that you dont injure yourself when using thumbtacks. If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 17).
Connecting AntennasContinued
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.
Connecting an Outdoor AM Antenna

Analog audio cable (RCA)

R ---- L

S VIDEO OUT

AUDIO OUT
cable supplied with the RI Dock
Onkyo RI Docks rear panel

Red White White

What can you do with ? Connecting an Onkyo RI Dock to the CD receiver with an cable allows you to control the RI Dock with the CD receivers remote controller. In addition, when playback is started on the RI Dock, the CD receiver will automatically select it as the input source. To use , you must connect the RI Dock to the CD receiver with an cable and an analog audio cable (RCA). On the RI Dock, set the MODE switch to HDD. See the RI Docks instruction manual for details. CR-515 To use , the Input Display for the DOCK/CDR jacks must be set to DOCK. Since this is the default setting, unless youve changed it, it can be left as it is (see page 29).
Connecting an Onkyo CD Recorder (CR-515)
The following diagram shows how to connect an optional Onkyo CD recorder. Connect the CD receivers DOCK/CDR OUT jacks to the CD recorders INPUT (REC) jacks, and connect the CD receivers DOCK/CDR IN jacks to the CD recorders OUTPUT (PLAY) jacks.
Onkyo CD recorders rear panel

White White

White Red

Red White

cable supplied with the Onkyo CD recorder : Signal ow
What can you do with ? Connecting an Onkyo CD recorder to the CD receiver with an cable allows you to control the CD recorder with the CD receivers remote controller. In addition, when playback is started on the CD recorder, the CD receiver will automatically select it as the input source. To use , you must connect the Onkyo CD recorder to the CD receiver with an cable and an analog audio cable (RCA). In addition, the Input Display for the DOCK/CDR jacks must be set to CDR (see page 29). Some -capable components have two jacks. Theyre both the same, so you can use either one. The extra jack is for connecting additional -capable components.
Connecting a Portable Audio Device
The following diagram shows how to connect a portable audio device (e.g., MP3 player, MD player, CD player). Connect the CD receivers LINE 2 IN jack (LINE IN jack on the CR-315) on the front panel to the portable audio devices output jack. Depending on the type of output jack on the portable audio device, you may need to buy a suitable cable. The CD receivers LINE 2 IN jack (LINE IN jack on the CR-315) accepts a stereo miniplug.
CR-515s front panel Portable audio devices output jack
Stereo miniplug cable : Signal ow
Notes: Use a connecting cable that doesnt have any attenuation resistors in it. If you connect a portable audio devices headphone output to the CD receivers LINE2 IN jack (LINE IN jack on the CR-315), turn down the volume on the portable audio device before you connect it. When you connect a portable audio device to the CD receiver, make sure you connect it to the LINE 2 IN jack (LINE IN jack on the CR-315) and not the adjacent PHONES jack. If you connect to the PHONES jack by mistake, it may cause the PHONES output to malfunction.

To turn on the CD receiver, press the [STANDBY/ON] button on the CD receiver or remote controller. The STANDBY indicator goes off. Press the [STANDBY/ON] button again to set the CD receiver to Standby. The STANDBY indicator lights up. Tip: When you start playback on (or turn on) an Onkyo RI Dock, CD recorder, MD recorder, or cassette deck thats connected to the CD receiver with an cable and analog audio cable, the CD receiver turns on automatically. Similarly, when you set the CD receiver to On or Standby, the other component will also be set to On or Standby.

TAPE * TAPE*

CR-315

CD LINE FM AM DOCK

*1 Input Display can be changed (see page 29). *2 CR-515 Asian model only.

Using Headphones

Turn down the volume, then connect your stereo headphones to the PHONES minijack. You can adjust the volume and mute the sound, as explained earlier. The speakers output no sound while the headphones are connected.

PHONES jack

Adjusting the Volume
Turn the [VOLUME] control clockwise to increase the volume or counterclockwise to decrease it. You can also use remote controllers VOLUME [ ]/[ ] buttons.

Basic OperationContinued

/ TONE ENTER DIRECT TONE S.BASS MUTING

DIRECT

Adjusting the Bass and Treble
Using the Direct Function
To turn the Direct function on or off, press the [DIRECT] button on the CD receiver. When the Direct function is off, the tone controls can be used to adjust the sound. When the Direct function is on, the tone controls are bypassed, so you can enjoy a pure sound, and the DIRECT indicator lights up.

DIRECT indicator

Press the [TONE] button to select Bass.
Use the Previous and Next [ ]/[ ] buttons to adjust the bass. The default setting is 0. You can adjust the bass and treble from 3 to +3. Press [ENTER], and then use the Previous and Next [ ]/[ ] buttons to adjust the treble. Notes: If you press no buttons for 8 seconds, the previous display will appear automatically. If you press the [TONE] button while the Direct function is on, the Direct function will be turned off.
On the remote controller, press the [TONE] button for 3 seconds to turn on the Direct function. On the CR-515, the [DIRECT] buttons indicator lights up when the Direct function is on.

Muting the Sound

To mute the output of the CD receiver, press the remote controllers [MUTING] button. The MUTING indicator ashes on the display. On the CR-515, the volume control indicator ashes, too.

MUTING indicator

On the CR-515, you can also use the [TONE] button and multi control on the front panel to adjust the bass and treble.

Playing CDs

Display

Disc tray /

Press the Eject [ ] button to open the disc tray. Tip: Pressing the Eject [ ] button while the CD receiver is on Standby will turn on the CD receiver and open the disc tray. Place the CD on the tray with the label-side facing up. Place 8 cm CDs in the center of the tray. To start playback, press the Play/Pause [ / ] button. The disc tray closes and playback starts. To stop playback: Press the Stop [ ] button. Playback stops automatically when the last track has been played. To pause playback: Press the Play/Pause [ / ] button. The Pause indicator appears. To resume playback, press the Play/Pause [ / ] button again. To remove the CD: Press the Eject [ ] button to open the disc tray.
DISC TOTAL lights up while the disc information is being displayed.
Selecting Tracks (CR-515)
To return to the beginning of the track currently playing, turn the multi control a little to the left. Turn the multi control further to select earlier tracks. While playback is stopped, turn the multi control to the left to select the previous track. Turn the multi control to the right to select subsequent tracks. On MP3 CDs, you can select MP3 les in other folders (see page 32).
Selecting Tracks (CR-315)
To return to the beginning of the track currently playing, press the Previous [ ] button. Press the Previous [ ] button repeatedly to select earlier tracks. While playback is stopped, pressing the Previous [ ] button will select the previous track. Press the Next [ ] button repeatedly to select subsequent tracks. On MP3 CDs, you can select MP3 les in other folders (see page 32).

Audio CD Display

Total number of tracks
Total playing time Disc name

MP3 CD Display

Total number of folders

Total number of les

Playing CDsContinued
Using the Remote Controller
Use the number buttons as shown in the examples below to select tracks.

To select:

Track #8 Track #10 Track #34 Used to enter numbers over 10. With MP3 CDs, you can select les in the current folder with these buttons.

Press:

Press to display more CD information Press to fast forward or fast reverse
During playback or while playback is paused, press and hold the Fast Forward [ ] button to fast forward, or the Reverse [ ] button to fast reverse.

Notes: On the CR-315, you can also use the CD receivers [DISPLAY] button to display this information. To display the disc name, press the [DISPLAY] button while playback is stopped. If a le or folder name contains any characters that cannot be displayed, an underscore will be displayed in place of those characters. Alternatively, you can set the CD receiver so that names containing such characters are displayed as File n or Folder n, n being the le or folder number (see page 37).

Memory Playback

With memory playback, you can create a playlist of up to 25 tracks.
To remove tracks from the playlist:
Number buttons (see page 31) (These buttons do nothing during memory playback)
Press the [CLEAR] button. Each press removes the last track from the playlist. Notes: If the total playing time is more than 99 minutes and 59 seconds, : is displayed. You can add up to 25 tracks to the playlist. If you try to add more, the message Memory Full appears.
MENU/NO/ CLEAR / / YES/MODE ENTER
To start memory playback, press the Play [ ] button.

Track currently playing

Memory playback can be set only when the input source is set to CD and playback is stopped.
On the CD receiver, press the Play/Pause [ / ] button to start memory playback.
Press the [YES/MODE] button repeatedly until the MEMORY indicator appears.

MEMORY indicator

Selecting Other Tracks During Memory Playback
To select other playlist tracks during memory playback, use the remote controllers Previous and Next [ ]/[ ] buttons.
Checking Whats on the Playlist
Use the Previous and Next [ ]/[ ] buttons to select the rst track you want to add to the playlist, and then press [ENTER].
To check what tracks are on the playlist, with playback stopped, use the Fast Reverse and Fast Forward [ ]/[ ] buttons to scroll through the playlist.
Removing Tracks from the Playlist
While memory playback is stopped, press the [CLEAR] button. Each press removes the last track from the playlist. The playlist will be deleted when you cancel memory playback, select random playback, turn off the CD receiver, or remove the CD.
Track to be added to the playlist

Total time of playlist

Repeat this step to add additional tracks to the playlist. You can also use the number buttons on the remote controller to select tracks. On the CR-515, you can also use the multi control to add tracks to the playlist. Turn the multi control to select a track, and then push it for ENTER.
To select MP3 les for memory playback:
In Navigation mode, use steps 14 on page 32. In All Folder mode, use steps 14 on page 33.

MENU/NO/ CLEAR ENTER

The MP3 preferences can be set only when playback is stopped.
Press the [MENU/NO] button repeatedly until Disc Name? appears.
Use the Previous and Next [ ]/[ ] buttons to select the preference you want to change. The preferences are explained in the next column. Press [ENTER].
Use the Previous and Next [ ]/[ ] buttons to select the preferences options.
Press [ENTER]. When the preference has been set, Complete appears on the display.
To cancel the procedure at any point, press the [MENU/NO] button.
Hide Number? (Disable/Enable) This preference determines whether or not the numbers at the beginning of le and folder names are hidden. When you create an MP3 CD on a personal computer, you cannot normally determine the playback order of the les. However, if you number the MP3 les in order, starting with 01, 02, 03, and so on, they will play in that order. If you dont want these numbers to appear on the display, choose Enable. The following table shows a few examples of numbered le and folder names and how they will appear with the Disable and Enable options.
File/folder name 01 Pops 10-Rock 16_Jazz 21th Century 05-07-20 Album Trk/Fld Num Option Disable 01 Pops 10-Rock 16_Jazz 21th Century 05-07-20 Album Enable Pops Rock Jazz 21th Century Album
Folder Key? (All Folder/Navigation) This preference determines how the [FOLDER] button works. When the All Folder option is selected, pressing the [FOLDER] button once selects All Folder mode and pressing and holding it for 2 seconds selects Navigation mode. When the Navigation option is selected, pressing the [FOLDER] button once selects Navigation mode and pressing and holding it for 2 seconds selects All Folder mode.
Tuning into Radio Stations

YES/MODE / ( TUN/ TUN )

Press the [BAND] button repeatedly to select AM or FM.
Press the [YES/MODE] button repeatedly to select Auto or Manual.

Auto Tuning Mode

The AUTO indicator appears and stereo radio reception is possible.

Manual Tuning Mode

The AUTO indicator is not displayed and radio reception will be in mono. When tuned into a station, the Tuned indicator appears. When tuned into a stereo FM station, the FM ST indicator appears as well.

AUTO indicator

Tuning into weak stereo FM stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono.
Use the Fast Reverse and Fast Forward [ ]/[ ] buttons to tune into a station. In Auto tuning mode, once a station is found, tuning stops automatically. The American model changes FM frequency in 0.2 MHz steps, 10 kHz steps for AM. For other models its 0.05 MHz steps for FM and 9 kHz or 10 kHz steps for AM. In Manual Tuning mode, the frequency stops changing when you release the button. Press the button repeatedly to change the frequency one step at a time.

Setting the Clock

Setting AccuClock to Use a Specic Station (European Model Only)
The AccuClock function normally uses the FM station with the strongest signal to set the clock. However, if the clock cannot be set properly using that station, you can specify which FM station the AccuClock function should use. This must be an FM station that supports RDS CT (Clock Time) information.
Press the [TIMER] button. Clock appears on the display. If the clock has already been set, a timer option appears instead, in which case youll need to press the [TIMER] button repeatedly until Clock appears. Press [ENTER]. AccuClockor *AccuClock* appears on the display. If Manual Adjust appears, use the Previous and Next [ ]/[ ] buttons to select AccuClock or *AccuClock*. Press [ENTER]. The frequency ashes on the display.
When youve selected the station, press [ENTER]. While the clock is being set, Wait ashes on the display. It may take a few minutes to set the clock. When the clock has been set, the message Clock Adjusted scrolls across the display, then the day and time are displayed for a while. Notes: If the clock is not set correctly, specify another FM station and try again or set the clock manually (see page 48). The AccuClock function automatically updates the clock every day. If you dont want it to, you can turn off the AccuClock function (see page 26).
Use the Rewind and Fast Forward [ ]/[ ] buttons to tune into the FM station. Tip: If you press the [YES/MODE] button instead of using the Rewind and Fast Forward [ ]/[ ] buttons, the CD receiver will automatically search for a suitable station. The RDS indicator appears when tuned into a station that supports RDS. The RDS indicator will ash while the CD receiver searches for a station and light up continuously when a station is found.

RDS indicator

Setting the ClockContinued
Setting the Clock Manually
The time can be displayed in either 12- or 24-hour format.
STANDBY/ON Number button TIMER / CLOCK CALL DISPLAY
Use the Previous and Next [ ]/ [ ] buttons to set the time. You can also use the remote controllers number buttons to enter the time.
For the 12-hour format, use the remote controllers [>10] button to select AM or PM.

Using the TimersContinued

Programming the Timers

Notes: You must set the clock before you can program the timers. Before programming a timer to turn on the radio, you must preset the station you want to use. (See pages 40 and 41.) If you dont operate any buttons for 60 seconds while programming a timer, the procedure will be cancelled and the previous display will reappear.
STANDBY/ON Number buttons
Use the Previous and Next [ ]/ [ ] buttons to select the source, and then press [ENTER].
You can select the following sources: CR-515 FM, AM, TAPE, DOCK, LINE1, LINE2, DIGITAL, or CD. CR-315 FM, AM, TAPE, DOCK, LINE, or CD. If you selected Rec, CD cannot be selected as the source.

TIMER ENTER

If you selected AM or FM, use the Previous and Next [ ]/[ ] buttons to select the radio preset, and then press [ENTER].
Press the [TIMER] button repeatedly to select timer 1, 2, 3, or 4, and then press [ENTER].
If Clock appears, you need to set the clock (see pages 26, 47, 48).
If you selected Rec, make sure the name of the connected recorder is ashing on the display, and then press [ENTER].
Use the Previous and Next [ ]/ [ ] buttons to select Play or Rec, and then press [ENTER].
You can select TAPE or MD.
Use the Previous and Next [ ]/ [ ] buttons to select Once or Every, and then press [ENTER]. Select Once for on-off operation. Select Every to perform the same operation every week.
If you cant select Rec, make sure that your Onkyo cassette deck or MD recorder is properly connected to the MD/TAPE jacks (see pages 20 and 21) and the Input Display is set accordingly (see page 29).
If you selected Once, use the Previous and Next [ ]/[ ] buttons to select the day, and then press [ENTER]. You can select: SUN, MON, TUE, WED, THU, FRI, or SAT.
Use the Previous and Next [ ]/ [ ] buttons to specify the Off time, and then press [ENTER].

TIMER indicator

If you selected Every, use the Previous and Next [ ]/[ ] buttons to select the day, Everyday, or Days Set, and then press [ENTER]. You can select the following:

MON TUE WED THU FRI

Underscore indicates timer programmed for recording
Number of programmed timer

Days Set

Everyday
Use the Previous and Next [ ]/ [ ] buttons to specify the CD receivers volume level, and then press [ENTER].
If you selected Days Set, use the Previous and Next [ ]/[ ] buttons to select the rst day, and then press [ENTER].
The default setting is 10. If you want to use your normal volume level setting for the timer, press the Previous [ ] button repeatedly until TimerVol.Off appears on the display. In this case, the timer will use the volume level that was set before the CD receiver was set to Standby.

Use the Previous and Next [ ]/ [ ] buttons again to select the last day, and then press [ENTER].
Press the [STANDBY/ON] button to set the CD receiver to Standby. Notes: Be sure to set the CD receiver to Standby, otherwise the timed operation will not work. While a timed operation is in progress, you can cancel it by pressing the [TIMER] or [SLEEP] button. While timed recording is in progress, the output of the CD receiver is muted. To hear whats being recorded, press the [MUTING] button. Press it again to mute the CD receiver. Memory, random, and 1-Folder playback cannot be used with the timers.
You can select only consecutive days.
Use the Previous and Next [ ]/ [ ] buttons to specify the On time, and then press [ENTER].
You can also use the remote controllers number buttons to enter the time. For example, to enter 7:29, press [>10], [0], [7], [2], and [9]. Notes: Once the On time is set, the Off time is automatically set to one hour later. To ensure that the rst few seconds of a program are recorded when using timer recording, set the On time slightly ahead of the programs start time (about 1 minute).
To return to step 1 and start timer programming all over again, press the [MENU/NO] button at any point in this procedure.
Turning Timers On and Off
Once a timer has been programmed, you can turn it on or off as necessary. For example, while youre on holiday, you may want to turn off the timer you use as an earlymorning alarm.

Checking Timer Settings

TIMER /
Press [ENTER] repeatedly to see all of the timers settings.
Press the [TIMER] button repeatedly to select timer 1, 2, 3, or 4.
When a timer has been programmed, its number appears on the display.
Use the Previous and Next [ ]/ [ ] buttons to select Timer On or Timer Off.
Notes: You can change the settings by using the Previous and Next [ ]/[ ] buttons. If you change the settings of a timer that is off, that timer will be turned on. If you dont change any settings, the previous display reappears. To return to the previous display at any point in this procedure, press the [MENU/NO] button.
After a few moments, the previous display reappears.

The sound quality is not good.
Make sure the speaker cables are connected with the correct polarity (see page 18). Make sure all audio connecting plugs are pushed in all the way (see page 19). The sound quality can be affected by strong magnetic elds, such as that from a TV. Try moving any such devices away from the CD receiver. If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone thats being used to make a call, the CD receiver may output noise. The CD receivers precision drive mechanism may emit a faint hissing sound while reading discs during playback or when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
The CD receiver is not a portable device. Use it in a location thats not subject to shock or vibration.
Headphone output is intermittent or theres no sound.
This may be due to dirty contacts. Clean the headphones plug. See your headphones instruction manual for cleaning information. Also, make sure that the headphones cable is not broken or damaged.

Audio performance

Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time to warm up. Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so dont do it. CD Playback

Playback jumps.

The CD receiver is being subjected to vibration or the disc is scratched or dirty (see page 15).

TroubleshootingContinued

Cant add tracks to the playlist for memory playback.
Make sure theres a disc in the CD receiver. Also, you can only add valid track numbers. For example, if the CD contains 11 tracks, you cannot add track #12.

The disc will not play.

Make sure the disc has been loaded correctly, with the label-side facing up. Check to see if the surface of the disc is dirty (see page 15). If condensation is suspected, turn on the CD receiver and leave it for 1 hour before playing any discs. Some CD-R/RW discs may not be playable (see page 14).

Audio Outputs

Analog Outputs: Subwoofer Pre Outputs: Speaker Outputs: Phones: 2 (DOCK, TAPE) (TAPE) 1

Amplier Section

Power Output: European: Asian:
2ch 20 W (4, 1 kHz, 2ch driven, IEC) 19 W + 19 W (8, 1 kHz, JEITA) 26 W + 26 W (4, 1 kHz, JEITA)
North American: 14 W + 14 W (8, 1 kHz, FTC) 19 W + 19 W (4, 1 kHz, FTC) European: 2ch 19 W (4, 1 kHz, 2ch driven, IEC) 18 W + 18 W (8, 1 kHz, JEITA) Asian: 25 W + 25 W (4, 1 kHz, JEITA) 22 W + 22 W (3, Front) 20 W + 20 W (4, Front) 14 W + 14 W (8, Front) 0.9% (Power Rated) 0.4% (1 kHz, 1 W) 25 (Front, 1 kHz, 8 ) 150 mV/50 k (TAPE) 150 mV/2.2 (REC OUT) 10 Hz100 kHz/3 dB (TAPE) 6 dB, 80 Hz (BASS) 8 dB, 10 kHz (TREBLE) +7 dB, 80 Hz (S.BASS) 100 dB (LINE, IHF-A)

Dynamic Power:

THD (Total Harmonic Distortion): Damping Factor: Input Sensitivity and Impedance: Output Level and Impedance: Frequency Response: Tone Control:
Signal to Noise Ratio: Speaker Impedance:
22 W + 22 W (3, Front) 20 W + 20 W (4, Front) 14 W + 14 W (8, Front) 0.4% (1 kHz, 1 W) 25 (Front, 1 kHz, 8 ) 150 mV/50 k (TAPE) 150 mV/2.2 (REC OUT) 10 Hz100 kHz/3 dB (TAPE) 6 dB, 80 Hz (BASS) 8 dB, 10 kHz (TREBLE) +7 dB, 80 Hz (S.BASS) 100 dB (LINE, IHF-A)

Tuner Section

Tuning Frequency Range: Usable Sensitivity: Signal to Noise Ratio: THD (Total Harmonic Distortion): Stereo Separation:
87.5 MHz108.0 MHz Stereo: 22.2 dBf (IHF) Stereo: 67 dB (IHF-A) Stereo: 0.5% (1 kHz) 40 dB (1 kHz) Mono: 15.2 dBf (IHF) Mono: 73 dB (IHF-A) Mono: 0.3% (1 kHz)
North American: 87.5 MHz107.9 MHz Others: 87.5 MHz108.0 MHz Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF) Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A) Stereo: 0.5% (1 kHz) Mono: 0.3% (1 kHz) 40 dB (1 kHz)
Tuning Frequency Range: Usable Sensitivity: Signal to Noise Ratio: THD (Total Harmonic Distortion): 522 kHz1611 kHz 300 dBf (30 V) 40 dB 0.7% North American: 530 kHz1710 kHz Others: 522 kHz1611 kHz 300 dBf (30 V) 40 dB 0.7%
Frequency Response: Audio Dynamic Range: THD (Total Harmonic Distortion): Wow and Flutter: Audio Output/Impedance (Analog):
4 Hz20 kHz 96 dB 0.005% Below threshold of measurability 1.3 V/1.0 k
10 Hz20 kHz 95 dB 0.009% Below threshold of measurability 1.3 V/1.0 k
Specications and features are subject to change without notice.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/ ONKYO EUROPE UK Office Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452 ONKYO CHINA LIMITED Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.ch.onkyo.com/