Exp. E74088

77 102

SUP 021 YOR

Cod. 10000022-23-30-31-32-501

NOTE POS

9161.112.227721800 U142.0701.031.0701.014.150 NE03.229183750 229183752

DESCRIPTION

WATER CONTAINER LID SMART NATURAL/GREY BLACK KNOB WATER CONTAINER LID SMAR WATER TANK FILTER CAP FOR FLOATING SPACE TRANSP./GREY LEVEL FLOAT GREY EPDM OR METRIC 0019-10 OR METRIC 0060-30 IN SILICONE SPRING FOR WATER CONTAINER VALVE GREY PISTON FOR WATER VALVE WATER CONTAINER AS.SMART NATUR/GREY SCREW TCB 2,9X6,4 DIN 7981 BZ NICK SUPPORT WATER CONTAINER W/O LAMP HOUSING SUPPORT WATER CONTAINER W/O LAMP HOUSING 2 POLE LEVEL SENSOR AS.SMART 2 POLE LEVEL SENSOR AS.SMART HI-LO TC SCREW 3X10 STEEL SCREW PANELVIT TCB 3X16 DIN7505 BRU UPPER TECHMATE INSERT FOR BOX SMART1 LOWER TECHMATE INSERT FOR BOX SMART SQUARE ADHESIVE FOOT 5023 BLACK HANGRIP SX SMART CHROMED SCREW TCB 2,9X6,4 DIN 7981 NICK DISPLAY BOX SAECO INCANTO S-CLASS DISPLAY BOX SAECO INCANTO S-CLASS USA GROMMET FOR POWER CABLE SMART SEALING SUPPORT AS.WATER DRIP TRAY BEAN COFF.CONT.LID SMART NATUR/GREY CONFECTION SAECO AQUA PRIMA GRIND.ADJUST.NATGREY KNOB SMART S/S PANELVIT TSP 4,5X16 DIN 7505 A GAL BAND FOR LIFTING L=1550 H=300 MM SEAL COVER GREY WATER CONTAIN.VALVE SEAL GACO DIM14 SEAL CONTAINER GREY BIPOLAR SWITCH FUSIT C1250AR INSERT FOR DECALCIFYING FILTER CAP FOR COFFEE DISPENSER TUBE BEAN COFFEE CONTAINER SEAL SMART SWITCH GENERAL SUPPORT BLACK SMART SILVER SUPPORT GRATE METAL SMART BLACK SUPPORT GRATE METAL SMART BLACK SUPPORT GRATE METAL SMART/UL
U143.U109.005 U207.129660902
INSERT GRINDING ADJUSTM.KNOB SMART INT.CASING PROTECTION POWER CABLE OR METRIC 0040-20 IN EPDM SPRING FOR CREAM ADJUSTMENT SHAFT DOOR HINGE KIT SMART SILVER DOOR HINGE KIT SMART BLACK screw TORX TCB 3,5X16 F TIP BL HANGRIP DX SMART CHROMED CASING WITH KNOB SMART SILVER CASING WITH KNOB SMART BLACK DUMP BOX BLACK UNPAINTED SMART SILVER DRIP TRAY SMART BLACK DRIP TRAY SMART BLACK DRIP TRAY SMART/UL CPU/POWER ELECTR.BOARD RONDO/V1 RS CPU/POWER ELECTR.BOARD RONDO RS CONNECTOR FOR STEAM TUBE PLATE FOR DOOR METALLIC SMART TOUCH PANEL ELECTRONIC BOARD RONDO BLACK SUPPORT ELECTRONIC CARD RONDO BLACK SUPPORT ELECTRONIC CARD RONDO/UL SUPPORT FOR BUTTONS RONDO BLACK BLACK BUTTON FOR ONE COFFEE FRONT PANEL SILVER RONDO SIL/SCREEN FRONT PANEL BLACK RONDO SILK/SCREEN SUPPORT CREAM ADJUSTMENT SHAFT BLACK BUTTON FOR TWO COFFEE BLACK SUPPORT FOR RING NUT RONDO POTENTIOMETER GEAR Z=58 RONDO COVER SMART SILVE.W.O/OPEN S/SCREEN BLACK COVER W.O/OPEN S/SCREEN PLUS RONDO BLACK COVER RONDO/UL SILK/SCREEN BLACK COVER W.O/OPEN S/SCR.PLUS RONDO/UL BRUSH FOR CLEANING BLACK BUTTON FOR WARM WATER RONDO INSTRUCT.MANUAL SAECO TYPE SUP021YOR INSTRUCT.MANUAL SAECO TYPE SUP021YOR INSTRUCT.MANUAL SAECO TYPE SUP021YOR screw AUT.TCB 3,5X16 DIN 7981 C PLAIN WASHER 3,2X7 UNI 6592 GAL COFFEE DISPENSER TUBE FOR ADJUST.SHAFT PANELVIT TCB SCREW 3,5X12 D.7505 Z

230V 120V 230V 120V

120V 230V 120V

230V 120V

7 LANGUAGES D/F/I GB/F/E

Rev. 02 - 28/02/06

TABLE 1a/3

0312.122842121

PANE.TCB SCREW 2,9X9,5 TES.D=7,5 ZN DISENGAGE LEVER GREY/SILVER DOOR SMART OR METRIC 0060-20 IN TERMOIL SCREW TSP3,5X9,5 DIN 7982 SS SUPPORT FOR ARTICULATED JOINT OR 117 IN SILICONE 70 SH SEMISPHERE SEAL FOR ARTICULAT.JOINT DOOR METALL SMART SILVER DOOR METALL SMART BLACK COFFEE DISPENSER SUPPORT WITH HOLE SILVER COFFEE DISPENSER AS.SMART BLACK COFFEE DISPENSER AS.SMART CONNECTOR FOR ARTICULATED JOINT CREAM ADJUSTMENT SHAFT SEAL FOR COFFEE DISPENSER V2 SMART RED FLOAT FOR DRIP TRAY SMART NATURAL/GREY BEAN CONTAINER SMART RETAINING INSERT TEFLON TUBE CREAM ADJUSTM.KNOB GLOSS CHR.PLATED BEAN CONT.PROTECT.SMART NATUR/GREY SPRING FOR BUTTON RONDO STAINLESS STEEL GRATE SMART SEAL FOR VALVE CONTAINER CONNECTOR FOR STEAM TUBE CHROME RING NUT FOR RONDO SCREW TCB 2,9X6,4 DIN 7981 BZ SS SQUARE ADHESIVE FOOT NB4256 BLACK ROTATING RING SMART WITH 3 FEET SCREW TSC PZ-B 2,9X9,5 UNI 6956 NI GACO SEAL FOR COFFEE DISPENSER TUBE WASHER UNI 8842 A3 SS SUPPOR.HINGE DOOR METAL.SMART SILV. SUPPOR.HINGE DOOR METAL.SMART BLACK SUPPOR.HINGE DOOR METAL.SMART BLACK SUPPORT DOOR METALLIC SMART SILVER SUPPORT DOOR METALLIC SMART BLACK SUPPORT DOOR METALLIC SMART BLACK SCREW TCB 2,9X9,5 DIN 7981 NICK PANELVIT TCB SCREW 3X8 DIN 7505 ZNP BLACK CAP FOR KNOB CREAM ADJUSTMENT EXTERNAL COVER ST.STEEL PANNAR.G100

142271350

SCREW TCB PH/SW 3X18 UNI 8112 INOX STEAM TUBE PROTECTION OR 108 IN SILICONE UPPER TUBE ASS.FOR PANNARELLO BLACK INTERN.INP.TUBE PANNAREL.G100

WITH PART. N92

101 102

TABLE 1b/3

IN ROLL 230V-50HZ 120V-60HZ 220V-60HZ IN ROLL 230V 120V
149185850 0311.229452100 9011.NM01.JS01.022 9161.9161.331.NM01.NE05.038 9121.046 148380200
90 CONNECTOR PUMP INLET SPRING HOSE CLAMP D=9,5MM SILICONE TUBE 5X8 70SR ULKA PUMP EP5/S GW ULKA PUMP EP5/S ULKA PUMP EP5/S GW PUMP SUPPORT HOLE 13,2 RED BLACK SILICON TUBE 7,5X9,3 EATON PUMP SUPPORT MAGIC 4002012 YELLOW HARNESS KLIXON JP 13 THERMAL. PROTECT 120C CABLE.125/3 OR 2031 IN TERMOIL PANE. TCB SCREW 3,5X16 TESTA D=8 Z COMPENSATION AND SAFETY VALVE ASSY FORK FOR TUBE D.4 OR 2015 IN SILICONE PTFE/FDA OR ORM 0050-20 SILICONE 3POLE CONNECT.AS.TURBINE JP18 SMART ANTIDISTURB FILTER 0,47X2+1000Y2+0,5L ANTIDISTURB FILTER 16A FNC 1610474472A PARTICULAR NOT AVAILABLE SILICONE TUBE 5XSHORE FORK FOR WATERWHEEL -M-VDE TURBINE WITH SENSOR KIT RATIOMOTOR COVER TRANSPARENT TURBINE SUPPORT SMART OR ORM 0090-20 SILICONE CABLE CLAMP V0 MAGIC ESP COMBI UL POWER CABLE SCHUKO BLACK L=1500 BLACK POWER CABLE CH H05+3FAST.L=1500MM P.CABLE SJT 16AWG USA BLACK L=1500 BLACK POWER CABLE KOREA 3X1,25 L=1600 CABLE 1 WIRE SILIC.BLACK THERM/FUSE 229 CABLE 1WIRE SILICON.BLACK AWG18+TH/FUSE TCB SCREW M4X8 UNI 7687 ZNP CONNECTOR AS.TEFLON 2X4 L=250 MM HEATING-ELEMENT BLECKMAN ASSY. 1000W HEATING-ELEMENT BLECKMAN ASSY. 1000W THERMOSTAT 175 INTERCONTR.161471002 THERMAL FUSE FIXING PLATE WASHER UNI 8842 A4 BURNISHED HEAT.ELEMENT PROTECTION BLECKMANN SMART MICROSWITCH SINTERED BUSH FOR MOTOR WASHER BAKELIZZATE D=5,5
9121.288582300 9011.129910103 9011.099 9121.042 9121.069.9011.U302.9161.129932502 9161.282058855
ANTIVIBRATION FOR MOTOR GENER.ASS.MOTOR FOR RATIOMOTOR GENER.ASS.MOTOR FOR RATIOMOTOR FLANGE NUT M8 TOOTHED BASE GALV. SENSOR ELECT.BOARD WITH CONNECTOR PEG FOR VALVE IN PLASTIC SCREW TAPT M4X10 DIN 7985 GALV HI -LO TC SCREW 3,5X15 RIF.910189 CURSOR FOR BOILER VALVE IN PLASTIC GEAR Z.12/90 GEAR Z.108 FOR MOUNTING PLATE M4000 OR METRICO 0080-20 SILICON.PTFE/FDA MICROSWITCH SAIA X3M502K2KAM92AS SCREW TCB PH/TT 4X8 UNI 8112 ZNP BRACKET BOILER SMART SUPPORT ROUND HEAD SCREW 10.9 M5X20 GALV SPRING FOR PIN PROTECTION FOR FOLK SPRING TUBE D=4 NUT HEXAGONAL M4 UNI 5588 BRASS PISTON L=20,9 ASSY. MYLAR WASHER FOR RATIOMOTOR SENSOR FIXING SPRING CONNECTOR AS.TEFLON 2X4 L=235 MM ELECTRIC INSULATING DISK D=16 THERMOSTAT 175 1NT-08L-3794 THERMOSTAT 175 1NT-08L-5125 SELF DRILLING SCREW 5X30 GALVANIZED INSULATING SPACER FOR BOILER 2 THERMOSTATS FIXING SPRING BRASS/NIK.PIN FOR PISTON L=20,9 CONNECTOR AS.TEFLON 2X4 L=330 MM BRASS/NIK.CONNEC.FOR BOILER SUPPORT SELF-LOCKI.NUT M5X0,8 DIN 980 CLA.8 SUPPORT FOR ALLUMINIUM BOILER SMART ALUM.BOILER AS.WITH RESISTANCE ALUM.BOILER AS.WITH RESISTANCE

230V 120V SEE PART. N20 IN ROLL WITH PART. N17
230V 120V 282135558 GENERAL TURBINE FOR SMART ASSY. ALUM.BOILER 120V AS.WITH RESISTANCE ALUM.BOILER 230V AS.WITH RESISTANCE WITH PART. N 13-14-23-28-40-41-43-44-47-49-51-52-53 55-57-59-60-63-64-66-67-68-69-70

Rev. 01 - 17/02/06

TABLE 2/3

9141.123030200

UPPER GRINDER SUPPORT COFFEEGRINDER NBR FDA OR METRIC 0530-15 BAKED CLAY KLAGER GRINDER 48X28 PIN M4-M6 NICK.FOR INCREMENT SCREW AXIAL BEARING EKKO 342.35252 UPPER GEAR SUPPORT COFFEEGRINDER SMART LOWER GEAR SUPPORT COFFEEGRINDER SMART COFFEE GRINDING ADJUSTMENT GEAR SMART LID GROUND COFFEE OUTLET CONVEYOR LOWER GRINDER SUPPORT COFFEEGRINDER SPRING FOR ADJUSTMENT GRINDING GEAR UPPER BODY WITH COFFE.GROUND OUTLET CRINKLE WASHER 21,8X15,8X0,2 RADIAL BEARING 61900.2RS1 PARTICULAR NOT AVAILABLE UP TO S/N 9005SA40367557 GEAR SX Z=38 FOR GRINDER MOTION ASSY. FROM S/N 9005SA40367558 ELECTRONIC BOARD WITH SENSOR HAL506 SF-K PARTICULAR NOT AVAILABLE UP TO S/N 9005SA40367557 MOTOR COFFEEGRINDER/V3 ASS. FROM S/N 9005SA40367558 - ONLY 230V MOTOR COFFEEGRINDER/V3 ASS. FROM S/N 9005SA40367558 - ONLY 120V SENSOR SUPPORT FOR COFF.GRIND.MOTOR FLAT WASH.DI=4,3 DE=14 SP=1,5 GALV. SELF LOCK NUT M4 DIN 982 HIGH GALV. CAP FOR WORM SCREW MC/V3 CENTRING DEADLOCK MOTOR FLANGE SMART1 COFFEGRIND.MOTOR SUPPORT SEAL SMART1 GENERAL MOTOR MC/V3 ASSY. GENERAL MOTOR MC/V3 ASSY. FELT RING 45,4X39,4X4 BREW UNIT WITH VALVE SMART BREW UNIT W/VALVE SMART/ELFO (SEE COD. EXP. E90041) GROUND COFFEE OUTLET CONVEYOR ASSY. PANELVIT TCB SCREW 3,5X18 D.7505 Z PANELVIT TCB SCREW 3,5X25 D.7505 ZN
9161.345.050 9161.333.227660303 NF11.JS01.019 9161.332.9011.20000410
COFEGRIND.MOTOR ANTIVIBR.SEAL SMART ASSEMBLY BOILER SUPPORT PLATE SMART MOUNTING PLATE NESPRESSO/UL WITH PIN PANE. TCB SCREW 3,5X16 TESTA D=8 Z BLACK GRINDER SUPPORT PLATE SMART BLACK GRINDER SUPPORT PLATE SMART/UL OR 2015 IN SILICONE PTFE/FDA GROUND COFFEE CONT.SEAL LOWER SMART1 FAUCET SUPPORT SMART PANELVIT TCB SCREW 3,5X12 D.7505 Z STRAIGHT CONNECTOR MICROSWITCH SAIA X3M502K2KAJ32AV INT.COVERING BLACK PUMP SPACE BOILER BLACK COVER SCREW TSP3,5X9,5 DIN 7982 SS BRASS PISTON L=15,1 ASSY. OETIKER CLIP STEEL SPRING BOIL. PISTON MAG.9011 CAP FOR FAUCET NESPRESSO BRASS/NIK. SPRING DI=7,5 FOR FABRIC FINISH TUB SILIC. TUBE FABRIC FINISH 3X7 EXT.COVERING BLACK PUMP SPACE PROTECTION FAUCET BODY WATER/STEAM FORK FOR TUBE D.4 FAUCET BODY MOD. OR D=4,18 X 1,90 IN TERMOIL FAUCET SHAFT FOR SMART STEAM KNOB ZAMAS CHROM.PLATED SMART SPARES KIT MOTOR COFFEEGRINDER/V3 230V UP TO S/N 9005SA40367557 - ONLY 230V SPARES KIT MOTOR COFFEEGRINDER/V3 120V UP TO S/N 9005SA40367557 - ONLY 120V

SEE PART. N57

18 181554200

SEE PART. N57 230V 120V

IN ROLL

129661702

WITH PART. N16 - 18 WITH PART. N16 - 18

OTHER COUNTRY

TABLE 3/3

Read these operating instructions carefully before using the machine
Bedienungsanleitung ist vor dem ersten Gebrauch der Maschine aufmerksam zu lesen
Lire attentivement ce mode demploi avant dutiliser la machine
Diese Leer atentamente estas instrucciones de uso antes de utilizar la mquina
Ler atentamente estas instrues de uso antes de utilizar a mquina
Lees deze INSTRUCTIES aandachtig door, alvorens het apparaat te gebruiken

OPERATING INSTRUCTIONS

BEDIENUNGSANLEITUNG

MODE DEMPLOI

INSTRUCCIONES DE USO

INSTRUES PARA USO

GEBRUIKSAANWIJZING

FOR HOUSEHOLD USE ONLY

Ideas with Passion

NEDERLAND PORTUGUS

ESPAOL

FRANAIS

DEUTSCH
Leggere attentamente queste istruzioni duso prima di utilizzare la macchina

ISTRUZIONI PER LUSO

ENGLISH

ITALIANO

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 2 Do not touch hot surfaces. Use handles or knobs. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. 5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any way. Return appliance to the nearest authorized service centre for examination, repair or adjustment. 7 The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. 8 Do not use outdoors. 9 Do not let cord hang over edge of table or counter, or touch hot surfaces. 10 Do not place on or near a hot gas or electric burner, or in a heated oven. 11 Always turn appliance OFF, then plug cord into the wall outlet. To disconnect, turn switch to OFF, then remove plug from wall outlet. 12 Do not use appliance for other than intended household use. 13 Use extreme caution when using hot steam.

CAUTION

This appliance is for household use. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service centre. Do not immerse base in water. To reduce the risk of fire or electric shock, do not disassemble the base. There are no user serviceable parts inside. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate agrees with your voltage. 2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during operation. 4 Never clean with scouring powders or hard implements. Simply use a soft cloth dampened with water. 5 To avoid your coffee maker scaling up, use purified or bottled water.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of getting tangled up or tripping over a longer cord. B Longer extension cords are available and may be used if care is exercised in their use. C If a long extension cord is used: 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. 2 if the appliance is of the grounded type, the extension cord should be a grounding type 3 the cable does not hang from the table to avoid the risk of getting caught up in it.

SAVE THESE INSTRUCTIONS

GENERAL INFORMATION
This coffee machine is ideal for preparing espresso coffee either with coffee beans or preground coffee and also features a device for dispensing steam and hot water. This elegantly styled machine is designed for household use only. It is not suitable for continuous professional-type use. Warning. The manufacturer shall accept no liability for damage or injury caused by: improper use or use for other than the intended purposes; repairs carried out by anyone other than an authorised service centre; tampering with the power cord; tampering with any machine component; use of spare parts and accessories other than those supplied by the manufacturer. The warranty will be invalidated in such cases.

TECHNICAL SPECIFICATIONS

Voltage rating Power rating Casing material Size (w x h x d) (mm) Weight (Kg) Cord length (mm) Control panel Water tank (lit.) Power supply Pump pressure (bars) Boiler Coffee container capacity (g.) Rapid Steam Grinders Quantity of ground coffee Dreg drawer capacity Safety devices See rating plate on appliance See rating plate on appliance Metal 285 x 375 x 1200 Front 2 - Extractible See rating plate on appliance 15 Stainless steel 300 of coffee beans Steam ready in a few seconds Ceramic 8g 13 Boiler pressure safety valve safety thermostat

A warning triangle draws attention to the instructions that are important for user safety. Please carefully abide by these instructions to avoid serious injury!
TO FACILITATE INTERPRETATION
HOW TO USE THESE OPERATING INSTRUCTIONS
Keep these operating instructions in a safe place and make them available to anyone else who should use the coffee machine. For further information or an explanation of problems not completely or sufciently addressed in these instructions, contact an authorised service centre.
Subject to engineering and manufacturing changes as warranted by technological developments. Machine in conformity with European Directive 89/336/EEC (Italian Legislative Decree 476 of 04/12/92) concerning electromagnetic compatibility.

SAFETY RULES

IN THE EVENT OF AN EMERGENCY
Immediately unplug the appliance. - The appliance must not be used by children or by individuals unacquainted with the operating instructions. - The appliance is dangerous for children. If left unattended it must be switched off. - Do not leave the materials used to pack the appliance within childrens reach. - Do not direct a jet of hot steam and/or hot water toward yourself or others: danger of scalding. - Do not introduce any objects through the openings in the appliance (Electrical hazard!). - Do not touch the plug when your hands or feet are wet. Do not unplug the appliance by yanking at the power cord. - Warning: contact with hot water, steam or and hot water/steam nozzle may cause burns. - Do not use the appliance if it malfunctions or you suspect damage, e.g. after a fall. - Repairs must be performed by an authorised service centre. - Do not use an appliance with a defective power cord. Should the power cord be damaged, it must be replaced by the manufacturer or his customer service department. (Electrical hazard!). - Switch off the appliance before opening the service door. Danger of burns!

HAZARDS

THE APPLIANCE MAY ONLY BE USED
- In a closed place. - To prepare coffee, dispense hot water, froth milk or heat beverages using steam. - For household use. - By adults in full possession of their physical and mental capacities.

NEVER USE THE APPLIANCE

for purposes other than those indicated above to avoid hazards. Never place any substances in the containers other than those specied in the instruction manual. When you ll a container, make sure all nearby containers are closed. Fill the water tank only with fresh drinking water: hot water and/or other liquids may damage the machine. Do not use carbonated water. The coffee grinder may be adjusted only while it is running. Do not introduce your ngers or any material other than coffee beans into the coffee grinder. Before attempting to access the inside of the coffee grinder, switch OFF the machine and remove the plug from the electric socket. Do not put coffee beans or instant coffee into the ground coffee container.

FAULTS

MAINS CONNECTION INSTALLATION
Connect the coffee machine to a suitable electric socket. The voltage must match the voltage specied on the appliance rating plate. - Choose a perfectly level supporting surface. Do not place on a hot surface! - Maintain a distance of 10 cm from walls and electric or gas burners. - Do not keep at temperatures below 0 C; the appliance may be damaged by freezing. - The electric socket must be accessible at all times. - The power cord must not be damaged, secured with clamps, placed on very hot surfaces etc. - Do not let the power cord hang loosely (Warning: danger of tripping or of causing the appliance to fall). - Do not use the power cord to carry or pull the coffee machine.

CLEANING / DESCALING

- Before cleaning the appliance, unplug it and allow it to cool down. - Avoid exposing the appliance to splashes of water. Do not immerge it in water. - Do not dry machine components in a conventional or microwave oven.

SPARE PARTS DISPOSAL

To guarantee safety, you should use only original spare parts and accessories.
- The packing materials can be recycled. - Appliance: unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service centre or public waste disposal facility.

COMPONENT DESCRIPTION

Cup heater plate Preground coffee dispenser lid Coffee bean container lid Coffee bean container Water tank lid Water tank Steam knob Service door SBS ON/OFF switch Height and depth adjustable brew unit Drip tray + grill Tray full indicator Swivel base Dregs drawer Brew group Hot water/steam tube Small coffee button Coffee button Preground coffee selector button Hot water selector button Descaling button Grind adjustment knob Alarm light Aqua Prima lter replacement light - see page 27 Coffee bean container and dregs drawer indicator light Water tank and circuit loading indicator light Cartridge lter applicator Aqua Prima cartridge lter Cleaning brush Brew group key

Control panel

Water hardness test

Preground coffee measure

INSTALLATION / VENTILATE
The messages displayed by the machine during operation are shown on pg.31. Important warning for using the Aqua Prima Filter can be found at page 31.
See rating plate Fill the coffee bean container with coffee beans. The Aqua Prima lter can be installed (see pg.27). Fill the tank with fresh drinking water. Insert the plug into a suitable electric socket. Move the ON/OFF switch to I to turn on the machine.

Flashing Flashing

Steadily
The machine indicates that the circuit needs loading.
Place a container beneath the steam tube.
Turn the knob counterclockwise to start loading the circuit.
Wait until a steady stream of water ows out from the nozzle.
Turn the knob clockwise to terminate the circuitloading process.

Flashing

Note: You must load the circuit before starting up the machine for the rst time, if it has been inoperative for a lengthy period or if the water tank has been completely emptied. The circuit must also be loaded each time the light ashes:

Remove the container.

The machine is warming up; lights are ashing.
When the indicator lights are xed, the machine is ready for use.

ADJUSTMENTS

COFFEE GRINDER

ADJUSTMENT

Adjustment may be made only while the coffee grinder is operating. Use coffee bean blends for espresso coffee makers. If you do not obtain the desired result, try using a different coffee blend. Store coffee in a cool place, in a hermetically sealed container. You will note a change after dispensing 1 - 2 coffees. Coffee ows out slowly. Press and turn. Coffee ows out quickly. Press and turn. If you set the grinder on too ne a grind (knob turned all the way anticlockwise) and the SBS control on strong (toward the right), coffee may ow out in a slow trickle or not at all.
The neness of the grind may be adjusted using the knob.
For machines provided with SBS only. - To adjust the strength and consistency of brewed coffee. The adjustment can also be made while brewing the coffe. This adjustment will have an immediate effect on the coffee brewed.

Caf crme

Espresso coffee

Strong black coffee

BIG CUPS To place the brew unit again in its position, pull it until it ts in.

COFFEE IN CUPS

BIG CUPS
COFFEE IN CUPS To adjust the quantity of coffee dispensed to the size of your cups. Place a cup beneath the brew unit, press the button corresponding to the type of coffee desired and keep it Or pressed while coffee is being dispensed. When the cup has lled to the desired level, release the button; the machine is now programmed to dispense the quantity of coffee you have chosen.

To use big cups, press the button and push the brew unit until the end.
DISPENSING COFFEE / HOT WATER
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.

COFFEE BEANS

Steadily lit
Make sure that the machine is ready.
Position a warm coffee cup or cups beneath the brew unit.
Press the button of the type of coffee desired. Once for 1 coffee

Twice for 2 coffees.

When the machine stops making the coffee, remove the cup or cups.

PREGROUNDCOFFEE

Position a warm coffee cup beneath the brew unit.
Select the product Preground coffee.
Introduce ground coffee using the coffee measure. MAX 1 MEASURE
Press the button of the type of coffee desired.
When the machine stops making the coffee, remove the cup.

HOT WATER

Press the button dispense water.
Turn the knob counterclockwise to start dispensing. Close the knob when nished.
Press the button to restore the machine to normal operation.

STEAM / CAPPUCCINO

CAPPUCCINO
Fill a cup to 1/3 with cold milk.
Place a container beneath the steam tube. Open the knob to discharge any residual water.
When only steam comes out, close the knob. Remove the container.
Position the cup containing milk beneath the steam tube.
Open the knob to release steam.
Move the cup in a circular fashion to heat the milk evenly.
After frothing the milk, close the knob.
Remove the cup and position it beneath the brew unit
Wipe the nozzle clean with a damp cloth to prevent milk encrustations.
Dispense coffee into the cup to prepare a delicious cappuccino.
Open the knob to discharge any residual water. Close the knob.
Place the cup beneath the steam tube. Open the knob.
Heat by moving in circles.

Close the knob.

DESCALING
Warning! Never use vinegar as a descaling agent. You can use any commercially available non-toxic, non-harmful descaling product for coffee machines. We recommend using a Saeco descaling agent. Descaling is necessary every 3-4 months, when there is a reduction in the water capacity. The machine must be on; it automatically controls the distribution of the descaling solution.

Steadily Flashing lit

When the machine needs descaling, the indicator light will ash.
Remove the cartridge lter carefully.
Fill the water tank with the descaling solution.
Place a large receptacle beneath the steam tube.
Press the button for 5 seconds.

Open the knob.

The descaling process starts.
The solution will be discharged at intervals.
The lights will ash to signal when descaling is over.
Close the knob. Remove the container.
Rinse out the tank and ll it with fresh drinking water.
If the descaling cycle is interrupted, the water tank and internal machine circuits must be rinsed. When descaling is over, t the cartridge lter back in place.

Open the knob to rinse.

When no water is left, turn the knob to close the valve.
AQUA PRIMA CARTRIDGE FILTER
The lter must be replaced when signalled by the machine. See Page 31. Before descaling, remove the lter from the tank.

INSTALLATION

Remove the lter from the packing container. Adjust the dater to the current month.
Insert the applicator and turn it clockwise to secure it to the lter.
Check where the lter positioning and reference mark is.
Put the lter into the empty tank.
The reference must be positioned in correspondence with the groove.
Press until the end limit.
Turn the applicator counter-clockwise and remove it from the tank.
Fill the tank with fresh drinkable water.
Position a container beneath the steam tube and turn the machine on.
Press the button to dispense water.
It is possible to use the machine without lter, Saeco suggests its use. If lter is not used, the machine must be descaled more frequently. Adjust the water hardness (see programming the machine functions).
Open the knob dispense water.
Empty the water tank out at intervals.
When the tank is empty, ll it again with fresh drinkable water.
Press the button and keep it pressed; when the indicator light is ashing, release the button.
You can now use your coffee machine.

CLEANING AND MAINTENANCE

Do not dry the machine and/or its components in a microwave and/or conventional oven. Do not immerge the machine in water and do not place any of its components in a dishwasher.

BASIC CLEANING

Turn the machine off. Unplug the machine.
Wash the water tank. Wash the lter inside it.
Remove the drip tray, empty it out and wash it.
Remove the dregs drawer, empty it out and wash it.
Remove and clean the pannarello attachment.

The machine, its components and the brew group must be cleaned at least once a week.
Use the brush to clean the ground coffee dispenser.

BREW GROUP

Remove the grill. Open the front door. Remove the drawers. Set all machine components back in position. Close the door.
Remove the brew unit and wash it with water.
Press the PUSH button to release the brew group.
Unscrew the upper lter by the special wrench and wash it.
Fit the lter back in place when clean.
Wash the unit, dry it and t it back in place. Do not press the PUSH button.
PROGRAMMING MACHINE FUNCTIONS
The user can change some machine operating parameters to suit his/her personal needs.

PROGRAMMING START

Procedure for accessing machine programming mode.

Turn the machine off.

Press the buttons together. Keeping the buttons pressed down, turn on the machine.

WATER HARDNESS

The hardness of tap water may vary depending on the region. For this reason, the appliance can be set according to the water hardness in the place where it is to be used, expressed on a scale of 1 to 4. The appliance is factory set on a hardness value of 3*. The setting should be adjusted according to the level of water hardness in the local area. Dip the strip in water for 1 second.
Hardness 4 Hardness 3 Hardness 2 Hardness 1
Check how many squares change colour.
Press the button to program the water hardness.
Hardness 4 Hardness 3* Hardness 2 Hardness 1
If the Aqua Prima lter has been installed in the machine, set the machine according to these indications. The degree of hardness will be signalled by the indicator lights.
If the Aqua Prima lter has NOT been installed, set the machine according to these indications. The degree of hardness will be signalled by the indicator lights.

PREBREWING

With the pre-brewing process the coffee is slightly moistened before actual brewing. This brings out the full aroma of the coffee and lends it an excellent avour. It is possible to choose either enabled or disabled. Press the button to set the function. Prebrewing enabled (ON). Prebrewing disabled (OFF).

RINSING

When this function is enabled, the internal machine circuits will be rinsed immediately after the warming-up phase to ensure that coffee is prepared with fresh water only.
In all new appliances this function has already been enabled in the factory.

Press the button to set the function.

Rinsing enabled (ON).

Rinsing disabled (OFF).

END PROGRAMMING

This procedure serves to activate all the settings made.
Turn the machine back on to activate the programmed functions.
DISPLAY MESSAGES - NOTES ON THE AQUA PRIMA CARTRIDGE FILTER
The control panel display guides users and helps them to use the machine correctly.

Descale the machine

The machine is rinsing; wait until the machine has nished this operation.
Fill the water tank with fresh drinking water.
Replace the Aqua Prima lter in the tank. After replacing the lter in the tank, keep the button pressed; when the indicator light is ashing, release the button.
Load the circuit (Starting up)
ADDITIONAL INFORMATION FOR CORRECTLY USING THE AQUA PRIMA FILTER. Please follow these simple instructions to correctly use the Aqua prima lter: 1. Keep the Aqua prima lter cool and away from sunlight; the room temperature should be between +5C and +40C; 2. Do not use the lter in temperatures over 60C. 3. If the coffee machine is not used for 3 days, we recommend washing the Aqua prima lter; 4 If the coffee machine is not used for more than 20 days, it is advisable to replace the lter. 5. To store an already opened lter, seal it in a nylon bag and keep in the fridge; do not store it in the freezer to avoid damaging the lter properties. 6. Before using the lter, leave it to soak in the water tank for 30 minutes. 7. Once it is taken out of its pack, do not keep the lter in the open air. 8. The lter must be replaced 90 days after opening the packing or after treating 60 litres of drinking water.
Fill the coffee bean container with coffee beans.
Open the door, remove the dregs drawer and empty the used coffee grinds into a suitable container. Important note: the dregs drawer may be emptied only when the machine is on. The drawer must be removed for at least 5 seconds. If you empty the drawer with the machine off, you will not be able to dispense coffee the next time you switch the machine on.

Flashing Steadily lit

Fit the brew unit, drip tray and dregs drawer correctly into place. Close the front door. Coffee grinder motor jammed. Brew unit motor jammed. Contact an Authorised Service Centre.
The machine is in the heating phase; wait until the machine has nished this operation.

PROBLEMS - CAUSES - REMEDIES
PROBLEMS CAUSES REMEDIES PROBLEMS CAUSES REMEDIES
The machine does not The machine is not Move the main switch to ON. turn on. connected to the power Check the plug and the supply. connection The coffee is not hot The cups are cold. enough. Warm up the cups.
Coffee ows out in Excessively ne grind slow trickle or not at all.
Adjust to a coarser grind (turn the knob clockwise).
Only water is No preground coffee has Dispense again after dispensed when you been introduced. introducing preground coffee. select preground coffee. No hot water or steam The tube is dispensed. clogged. nozzle is Clean the nozzle opening with a needle.

and / or

and SBS control turned to Turn the SBS control toward the right. the left.
During this operation, the knob must be closed and the machine must be off. The machine takes a Excessive long time to warm up. built up. scale has Descale the machine.
The brew unit cannot The unit has stopped in Close the door and switch on be removed. the wrong position. the machine; the brew unit will move back into position.
Saeco International Group S.p.A. - Via Panigali, Gaggio Montano - Bologna - Italy Tel. +39 0534.771.111 - Fax. +39 0534.31025 - http://www.saeco.com

TYPE SUP021YNR