No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION.

Ver. 4.4 Install Guide

Ver. 4.4

Install Guide

Table of Contents
Introduction: About This Manual....1 Overview.....2 Windows.....3 Installing Nikon Capture 4 Under Windows...4 Easy Install.....7 Custom Install....14 Connecting to a Computer....21 Uninstall: Uninstalling Nikon Capture 4...23 Uninstalling Nikon Capture 4....23 Device Registration....24 USB Interface.....25 IEEE 1394 Interface....38 Macintosh.....69 Installing Nikon Capture 4 on a Macintosh...70 Installing Software....72 Connecting to a Computer....78 Uninstall: Uninstalling Nikon Capture 4...80 Uninstalling Nikon Capture 4....80

About This Manual

Introduction
About This Manual Thank you for your purchase of Nikon Capture 4 (Ver. 4.4). This install guide explains how to install and uninstall Nikon Capture 4 on your Windows or Macintosh computer, and how to connect your camera to your computer. It also explains how to insert a camera memory card in a card reader or PC card slot, how to start Nikon Capture 4, and how to register the camera with the system. Before reading this guide, be sure to read the Nikon Capture 4 Users Manual. The procedure for installing Nikon Capture 4 varies with the model of camera and computer operating system you are using. Be sure to read the sections of this guide that apply to your model of camera and computer operating system.

Overview

This guide is divided into two main parts, one for Windows and the other for Macintosh computers. Windows This section explains how to install and uninstall Nikon Capture 4 on your Windows computer, and how to connect your camera to your computer. It also explains how to insert the memory card in a card reader or PC card slot. Note that when you connect your camera to a Windows computer after installing Nikon Capture 4, the computer will automatically identify the camera as a new device and initiate device registration. For information on conrming that the camera is correctly registered with the system, see Device Registration in this manual, which describes how to conrm device registration with different models of camera and different versions of Windows. Macintosh This section explains how to install and uninstall Nikon Capture 4 on your Macintosh computer, and how to connect your camera to your computer. It also explains how to insert the memory card in a card reader or PC card slot.
Illustrations The illustrations in this guide are from Windows XP and Mac OS X. Depending on the operating system used, the dialogs and menus displayed on your computer may differ slightly from those shown here.

Windows

This section explains how to install and uninstall Nikon Capture 4, how to connect your camera and insert the camera memory card in a card reader or PC card slot, and how to register the camera with the system.
Installing Nikon Capture 4 Under Windows
Before installing Nikon Capture 4, make sure that your computer meets the following system requirements.
Pre-installed versions of Windows XP Home Edition, Windows XP Professional, Windows 2000 Professional, Windows Millennium Edition (Me), Windows 98 Second Edition (SE) CPU 300 MHz Pentium equivalent or better RAM 256 MB (768 MB or more recommended) Hard-disk space 200 MB required for installation Video pixels or more with 16-bit color (High Color/thousands of colors). 24resolution bit color (True Color/millions of colors) recommended. IEEE Open Host-Controller Interface (OHCI) compliant IEEE 1394 interface board or Interface 1394* card required for connection to D1, D1x, and D1h USB** Built-in USB interface Supported cameras D2-series, D1-series, D200, D100, D70s, D70, and D50 (Camera Control) CD-ROM drive required for installation. Other Internet connection required for some options. OS * The camera may not function as expected when connected to an IEEE 1394 hub. A list of boards and cards that have been tested and approved for use with the D1, D1X, and D1H is available on-line at the sites listed page 2 of the Users Guide. ** The camera may not function as expected when connected to a USB hub or keyboard.
Windows XP Home Edition, Windows XP Professional, Windows 2000 Professional Installing Nikon Capture 4 under a multi-user operating system requires Administrator privileges. When installing Nikon Capture 4, log in as: Windows XP Home Edition/Professional Windows 2000 Professional Computer administrator Administrators
Installing Nikon Capture 4 Under Windows When installing Nikon Capture 4, you can choose between Easy Install and Custom Install options.
Easy Install The following software will be installed in the order given below.

Windows 2.2.6 Choose default color management settings To use the color-space prole embedded in images opened in Nikon Capture 4, choose (A) Use the color space of the le to be opened as the working color space. To choose a default RGB color-space prole for the working color space in Nikon Capture 4, choose (B) Always use the default RGB color space as the working color space. When this option is selected, you can choose the default color-space prole from a pull-down menu. Click OK to put changes into effect and proceed to the next step.
Clicking About Color Spaces displays a description of the different color-space proles. Use this explanation to help you choose a color-space prole.
The default output color-space prole can be changed at any time after installation in the Color Management tab of the Nikon Capture 4 Editor or Nikon Capture 4 Camera Control Preferences dialog.
Installing Nikon Capture 4 Under Windows 2.2.7 Complete installation of Nikon Capture 4 The following dialog is displayed when installation of Nikon Capture 4 is complete. Click Finish to proceed to the next step.
2.3 Restart your computer The dialog shown below will appear when installation is complete. Click Yes to restart your computer. This completes the Easy Install procedure.

Custom Install

The standard installation procedure involves two steps: choosing the Custom Install option and installing the software. Step 1: Choose the Custom Install option Click the Custom Install tab and check the software you want to install.
Nikon Mass Storage Camera Drivers This check box is only displayed under Windows 98 Second Edition (SE). Check this box to install the Nikon Mass Storage Camera Driver for Windows 98 SE. Driver for D1 series cameras Check this box to install the drivers for the D1 series. Nikon Capture 4 Check this box to install Nikon Capture 4.
Before installation Before installing Nikon Capture 4 and the device drivers, make sure the camera is not connected to the computer. If the Device Wizard is displayed, click Cancel to exit the Wizard.

Windows 2.2.7 Complete installation of Nikon Capture 4 The following dialog is displayed when installation of Nikon Capture 4 is complete. Click Finish to proceed to the next step.
2.3 Complete installation The dialog shown below will appear when installation is complete. Click Yes to restart your computer.

Connecting to a Computer

If you are using a computer running Windows, make sure that you install Nikon Capture 4 before connecting your camera to the computer for the rst time. After installing Nikon Capture 4, turn the camera on and connect it to the computer, or insert the memory card into a card reader or a PC card slot. For more information about connecting your camera to a computer, see the documentation provided with your camera. D1-Series (IEEE 1394 Interface)
D2-Series/D200/D100 /D70s/D70/D50 (USB Interface)
Use a Reliable Power Source To ensure that data transfer is not interrupted, be sure that the battery is fully charged. If in doubt, charge the battery before use or use an AC adapter (available separately). If the battery is exhausted during transfer, transfer will be interrupted and data may be lost.
Windows Using a PC Card Slot When inserted in a PC-card adapter (available separately), the camera memory card functions as a Type II PCMCIA ATA card, allowing images to be read from the card. Inserting a Memory Card Remove the memory card from the camera and insert it in the adapter.
Insert the adapter into a PCMCIA TYPE II ATA card slot on your computer. For more information on inserting the adapter, see the documentation provided with your computer.

lash pactF Com

Card EC-

F 64C EC-

Depending on your computers operating environment, you may need to install software, register the card adapter, or adjust OS settings when the adapter is inserted into the card slot. For more information, refer to the instruction manual for your operating system. Using a Card Reader Images on the memory card can also be viewed using a card reader. Inserting a Memory Card After removing the memory card from the camera, insert it in the card reader and connect the reader to the computer. See the documentation provided with the card reader for more information on connecting it to a computer. Card reader (USB interface)

Card reader

Memory card

Uninstall

Uninstalling Nikon Capture 4 This section describes how to uninstall the Windows versions of Nikon Capture 4.
Uninstalling Nikon Capture 4
From the Start menu, select All Programs > Nikon Capture 4 > Nikon Capture 4 Uninstall (Windows XP) or Programs > Nikon Capture 4 > Nikon Capture 4 Uninstall (other versions of Windows). The uninstall program will start. The uninstall program will display the message, Do you want to completely remove the selected application and all of its components? Click OK to uninstall Nikon Capture 4.

If any of the components used by Nikon Capture 4 are read-only or are used by other programs, a conrmation dialog will be displayed. Follow the instructions in the dialog to remove components or leave them untouched. The dialog shown below will be displayed when the uninstall program has nished removing Nikon Capture 4 from your system. Conrm that Yes, I want to restart my computer now is selected and click Finish to restart your computer.
Windows XP Home Edition, Windows XP Professional, Windows 2000 Professional Uninstalling Nikon Capture 4 under a multi-user operating system requires Administrator privileges. When uninstalling Nikon Capture 4, log in as: Windows XP Home Edition/Professional Windows 2000 Professional Computer administrator Administrators

Device Registration

If you connect a supported digital camera to a Windows computer after installing Nikon Capture 4 and restarting the computer, Windows will automatically identify the camera as a new device and register the camera with the system. This section explains how to conrm that the camera is correctly registered. Read the section for your camera and operating system.
Operating system Windows XP Home Edition/Professional USB Interface (D2 series/D200/D100/D70s/D70/ Windows 2000 Professional D50/COOLPIX Series Cameras) Windows Millennium Edition (Me) Windows 98 Second Edition (SE) Windows XP Home Edition/Professional Windows 2000 Professional IEEE 1394 Interface (Nikon D1/Nikon D1X/Nikon D1H) Windows Millennium Edition (Me) Windows 98 Second Edition (SE) Windows 2000 Professional Nikon D1 previously registered under Nikon View Windows Millennium Edition (Me) DX or Nikon Capture 2 or earlier Windows 98 Second Edition (SE) Camera 65
Device Registration: USB Interface

USB Interface

Windows XP Home Edition/Professional The following explanation uses D100 as an example. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using a USB cable and turn the camera on. The camera will be registered automatically. If the Removable Disk dialog is displayed after registration, click Cancel to close the dialog box. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Select Control Panel from the Start menu. In the Control Panel window, click the Performance and Maintenance icon to open the Performance and Maintenance window. Click the System icon in the Performance and Maintenance window to open the System Properties window. Select the Hardware tab and click the Device Manager button. Step 2 The Device Manager will be displayed. After conrming that Disk drives, Storage volumes, and Universal Serial Bus controllers are listed in the Device Manager, click the plus sign (+) next to each of these device types.

Logging On You will need to log on as Computer Administrator to register the camera. Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Windows Step 3 Conrm that NIKON D100 USB Device, Generic Volume, and USB Mass Storage Device are listed respectively under Disk drives, Storage volumes, and Universal Serial Bus controllers. Double-click each of these listings to open the associated Properties window. If the NIKON D100 USB Device is listed under Other devices, delete this entry and then turn the camera off and then on again.
Step 4 The Properties dialogs for the selected devices will be displayed. Click the General tab and conrm that This device is working properly appears under Device status. Click OK.
Device registration is now complete. Click OK to close the System Properties dialog.
PTP If the USB option in the camera setup menu is set to PTP, conrm that the camera is listed in the Control Panel under Printers and Other Hardware > Scanners and Cameras.
Device Registration: USB Interface Windows 2000 Professional The following explanation uses D100 as an example. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using a USB cable and turn the camera on. The camera will be registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Right-click the My Computer icon on the desktop. Open the System Properties dialog by selecting Properties from the menu that appears. Open the Hardware tab and click the Device Manager button in the Device Manager area.
Step 2 The Device Manager will be displayed. After conrming that Disk drives, Storage volumes, and Universal Serial Bus controllers are listed in the Device Manager, click the plus sign (+) next to each of these device types.
Logging On Log on as Administrators to register the camera. Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Windows Step 3 Confirm that NIKON D100 USB Device, Generic volume, and USB Mass Storage Device are listed respectively under Disk drives, Storage volumes, and Universal Serial Bus controllers. Double-click each of these listings to open the associated Properties window. If the NIKON D100 USB Device is listed under Other devices, delete this entry and then turn the camera off and then on again.
PTP If the USB option in the camera setup menu is set to PTP, conrm that the camera is listed in the Scanners and Cameras Control Panel. The camera may be listed by name or as a Nikon DSLR camera.
Device Registration: USB Interface Windows Millennium Edition (Me) The following explanation uses D100 as an example. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using a USB cable and turn the camera on. The camera will be registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Right-click the My Computer icon on the desktop. Open the System Properties dialog by selecting Properties from the menu that appears. Click the Device Manager tab.

Step 2 After conrming that Disk drives, Storage de vice, and Universal Se ri al Bus controllers are listed in the Device Manager tab, click the plus sign (+) next to each of these device types.
Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Windows Step 3 Conrm that NIKON D100, USB Disk, and USB Mass Storage Device are listed respectively under Disk drives, Storage device, and Universal Serial Bus controllers. Double-click each of these listings to display the associated Properties window.
If the NIKON D100 is listed under Other devices, delete this entry and then turn the camera off and then on again. Step 4 The Properties dialogs for the selected devices will be displayed. Click the General tab and conrm that This device is working properly appears under Device status. Click OK.
Device Registration: USB Interface Windows 98 Second Edition (SE) The following explanation uses D100 as an example. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using a USB cable and turn the camera on. The camera will be registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Right-click the My Computer icon on the desktop and select Properties from the menu that appears. The System Properties dialog will be displayed. Click the Device Manager tab. Step 2 After conrming that Disk drives, Hard disk controllers, and Universal Serial Bus controllers are listed in the Device Manager tab, click the plus sign (+) next to each of these device types.
Windows Step 3 Conrm that NIKON D100, Nikon Digital Camera Controller, and Nikon Digital Camera Mass Storage Driver are listed respectively under Disk drives, Hard disk controllers, and Universal Serial Bus controllers. Double-click each of these listings to open the associated Properties window.
If the Nikon D100 is listed under Other devices, reinstall the device driver as instructed in Reinstalling the Device Driver ( 33).
If the three drivers above are not listed in the Device Manager and NIKON D100 is not listed under Other devices, disconnect the camera and restart the computer. When the computer has restarted, reconnect the camera to the computer. Step 4 The properties for the selected devices will be displayed. Click the General tab and conrm that This device is working properly appears under Device status. Click OK.
Device Registration: USB Interface Reinstalling the Device Driver Windows 98 Second Edition (SE) If NIKON D100 is listed under Other devices, you will need to reinstall the device driver. Step 1 Double-click the NIKON D100 listing under Other devices.

The bus controller for your IEEE 1394 board or card should be listed un der 1394 Bus host controllers.
If IEEE 1394 Bus host controllers is not listed in the Device Manager, or if your IEEE 1394 interface board or card is listed as an unknown or miscellaneous device or is preceded by a red or yellow warning icon, follow the instructions in the manual provided with the board to ensure that the drivers are properly installed. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using an IEEE 1394 cable and turn the camera on. The camera will be registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Select Control Panel from the Start menu to open the Control Panel window. Click the Performance and Maintenance icon inside the Control Panel window to open the Performance and Maintenance window. Click the System icon inside the Performance and Maintenance window to open the System Properties window. Select the Hardware tab and click the Device Manager button to open Device Manager window. After conrming that Nikon 1394 Protocol Device is listed in the Device Manager, click the + sign to its left.
Logging On You will need to log on as the Computer Administrator to register your camera. Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Device Registration: IEEE 1394 Interface If no Nikon 1394 Protocol Device listing appears or if NIKON D1X (or D1 or D1H) is listed under Other Devices, reinstall the device driver as instructed in Reinstalling the Device Driver ( 40). If Nikon 1394 Protocol Device is not listed in the Device Manager and NIKON D1X (or D1 or D1H) is not listed under Other Devices, disconnect the camera, and restart the computer. When the computer has restarted, reconnect the camera. Step 2 After conrming that Nikon Digital Camera D1 Series is listed under Nikon 1394 Protocol Device, double-click the listing to open the Properties window.
Step 3 The Nikon Digital Camera D1 Series Properties dialog will be displayed. Click the General tab and conrm that This device is working properly appears under Device status. Click OK.
Close the Device Manager, then click OK to close the System Properties window. Device registration is now complete.
Windows Reinstalling the Device Driver Windows XP Home Edition /Professional If NIKON D1X (or D1 or D1H) appears under Other Devices, reinstall the device driver as instructed below. Step 1 Open the Device Manager dialog. Doubleclick the listing for the Nikon D1X (or D1 or D1H) that appears under Other devices. The Properties dialog will be displayed.
Step 2 Open the General tab and click Reinstall Driver.

Step 3 The Hardware Update Wizard dialog will appear. Holding down the shift key to prevent the Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into the CD-ROM drive. (If the shift key is not held down, the Select Language dialog will appear when the CD-ROM is inserted.) Select Install the software automatically and click Next.
Device Registration: IEEE 1394 Interface Step 4 When the driver installation has been completed, the dialog shown at right will be displayed; click Finish to close the wizard.
Step 5 Conrm that This device is working properly appears under Device status in the General Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 6 Close the Device Manager, then click OK to close the System Properties window.
Windows Windows 2000 Professional Before You Begin Conrm that your OHCI-compliant IEEE 1394 interface board or card has been correctly registered with the system. Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears to display the System Properties dialog. Open the Hardware tab and click the Device Manager button in the Device Manager section.
If 1394 Bus host controllers does not appear in the Device Manager, or if your IEEE 1394 interface board or card is listed as an unknown or miscellaneous device or is preceded by a red or yellow warning icon, follow the instructions in the manual provided with the board to ensure that the drivers are properly installed. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using an IEEE 1394 cable and turn on the camera. The camera is registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Once registration is complete, check that the D1X (or D1 or D1H) has been correctly registered with the system. Click the My Com put er icon on the desk top with the right mouse button and select Properties from the menu that appears to display the System Properties dialog. Open the Hardware tab and click the Device Manager button in the Device Manager section.
Logging On You will need to log on as Administrators to register the D1, D1X, or D1H. Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer. Updating the Drivers for the D1 If you are already using the D1 with Nikon View DX or an earlier version of Nikon Capture, you will need 48). to update the camera drivers as described under Updating the Drivers for the D1 (

Step 10 Close the Device Manager, then click OK to close the System Properties window.
Windows Updating the Drivers for the D1 Windows 2000 Professional If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update the camera driver. Step 1 Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears to display the System Properties dialog. Open the Hardware tab and click the Device Manager button in the Device Manager section.
Step 2 The Device Manager will be displayed. Under the entry Nikon 1394 Device, double-click Nikon Digital Camera D1.
Step 3 The Nikon Digital Camera D1 Properties dialog will be displayed. Open the Driver tab and click Update Driver.
Logging On You will need to log on as Administrators to update the device drivers.
Device Registration: IEEE 1394 Interface Step 4 The Upgrade Device Driver Wizard will be displayed; click Next.
Step 5 The dialog shown at right will be displayed. Select the search option and click Next.
Windows Step 7 The dialog shown at right will be displayed. Select Install one of the other drivers and click Next.
Step 8 Select Nikon Digital Camera D1 Series from the dialog at right and click Next.
Step 9 The dialog shown at right will be displayed; click Finish.
Device Registration: IEEE 1394 Interface Step 10 Conrm that This device is working properly appears under Device status in the General Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 11 Close the Device Manager, then click OK to close the System Properties window.
Windows Troubleshooting If 1394 Bus host Controller is not displayed in the Device Manager, if the IEEE 1394 board or card is listed under Other Devices or Miscellaneous Devices, or if the listing for the IEEE 1394 board or card is preceded by a red or yellow warning icon the computer does not recognize the IEEE 1394 board or card. Refer to the documentation provided with your computer or IEEE 1394 board or card for information on registering the board or card with the system. If 1394 Bus host Controller is listed in the Device Manager but the entry for the Nikon D1 (or D1X or D1H) does not appear check the following: Is the camera on? Is the battery fully charged? If you are using an AC adapter (available separately), is it properly connected? Is the mode dial set to PC? Is the IEEE 1394 cable properly connected?

Device Registration: IEEE 1394 Interface Windows Millennium Edition (Me) Before You Begin Conrm that the OHCI-compliant IEEE 1394 interface board has been correctly registered with the system. Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears. The System Properties dialog will be displayed; click the Device Manager tab.
The bus controller for your IEEE 1394 board or card should be listed under 1394 Bus Controller.
If 1394 Bus Controller is not listed in the Device Manager, or if your IEEE 1394 interface board or card is listed as an unknown or miscellaneous device or is preceded by red or yellow warning icons, follow the instructions in the manual provided with the board to ensure that the drivers are properly installed. After installing Nikon Capture 4 and restarting the computer, connect your camera to the computer using an IEEE 1394 cable and turn on the camera. The camera will be registered automatically. Follow the instructions below to check that the camera has been correctly registered with the system. Step 1 Once registration is complete, check that the D1X (or D1 or D1H) has been correctly registered with the system. Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears. The System Properties dialog will be displayed; click the Device Manager tab.
Before Connecting the Camera Be sure to install Nikon Capture 4 before connecting your camera to the computer. Updating the Drivers for the D1 If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update the camera drivers as described in Updating the Drivers for the D1 ( 57).
Windows Step 2 The Device Manager sheet will be displayed. After conrming that Nikon 1394 Protocol Device is listed in the Device Manager, click the + sign to its left. If no Nikon 1394 Protocol Device listing appears or if NIKON D1X (or D1 or D1H) is listed under Other Devices, reinstall the device driver as instructed in Reinstalling the Device Driver ( 55). If Nikon 1394 Protocol Device is not listed in the Device Manager and NIKON D1X (or D1 or D1H) is not listed under Other Devices, disconnect the camera, and restart the computer. When the computer has restarted, reconnect the camera to the computer. Step 3 After conrming that Nikon Digital Camera D1 Series is listed under Nikon 1394 Protocol Device, double click the listing to open the Properties window. Step 4 The Nikon Digital Camera D1 Series Properties dialog will be displayed. Click the General tab and conrm that This device is working properly appears under Device status. Click OK.

Click OK to close the System Properties window. Device registration is now complete.
Device Registration: IEEE 1394 Interface Reinstalling the Device Driver Windows Millennium Edition (Me) If Nikon 1394 Protocol Device is listed Other Devices, reinstall the device driver as described below. Step 1 Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears. The System Properties dialog will be displayed; click the Device Manager tab. Step 2 The Device Manager sheet will be displayed. Double-click the listing for the Nikon D1X (or D1 or D1H) that appears under Other Devices or Miscellaneous Devices. Step 3 The NIKON D1X (or D1 or D1H) Properties dialog will be displayed. Open the General tab and click Reinstall Driver.
Step 4 The Update Device Driver Wizard will be displayed. Holding down the shift key to prevent the Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into the CD-ROM drive. Conrm that Automatic search for a better driver (Recommended) is selected and click Next. The wizard will automatically update the device drivers. The Select Language Dialog If the Select Language dialog appears when the CD is inserted, click the Quit button to close the dialog.
Windows Step 5 The dialog shown at right will be displayed; click Finish.
Step 6 Conrm that This device is working properly appears under Device status in the General Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 7 Click Close to close the System Properties window.
Device Registration: IEEE 1394 Interface Updating the Drivers for the D1 Windows Millennium Edition (Me) If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update the camera driver. Step 1 Click the My Computer icon on the desktop with the right mouse button and select Properties from the menu that appears. The System Properties dialog will be displayed; click the Device Manager tab. Step 2 The Device Manager sheet will be displayed. Under the entry Nikon 1394 Device, doubleclick Nikon Digital Camera D1. Step 3 The Nikon Digital Camera D1 Series Properties dialog will be displayed. Open the Driver tab and click Update Driver.
Step 4 The Update Device Driver Wizard will be displayed. Holding down the shift key to prevent the Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into the CD-ROM drive, select Automatic Search for a Better Driver (Recommended), and click Next. The wizard will automatically update the device drivers. The Select Language Dialog If the Select Language dialog appears when the CD is inserted, click the Quit button to close the dialog.
Windows Step 5 The dialog shown below will be displayed. Select the driver located at (Drive letter for CDROM drive):\ and click OK.
Step 6 The dialog shown at right will be displayed; click Finish.
Step 7 Conrm that This device is working properly appears under Device status in the General Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.

Click Continue to start the installer. 2.1.2 Accept the license agreement The license agreement will be displayed. After making sure that you have read and understood the contents of the agreement, click Accept to continue installation.
The ReadMe le will then be displayed. Take a few moments to view this le, which may contain important information that could not be included in the manual. After viewing the ReadMe le, click Continue.
Installing Nikon Capture 4 under Mac OS X The administrator password is required when installing Nikon Capture 4 under Mac OS X.
Macintosh 2.1.3 Choose Easy Install Choose Easy Install from the pull-down menu in the top left corner of the Nikon Capture Installer dialog.
2.1.4 Conrm the install destination The disk and folder to which Nikon Capture 4 will be installed are listed under Install Location.
2.1.5 Start the installer Click Install in the Nikon Capture Installer dialog to begin installation of Nikon Capture 4. A progress meter will be displayed during installation.
Earlier Versions of Nikon Capture Before you can install Nikon Capture 4, you must uninstall any earlier versions of Nikon Capture. Create Aliases (Mac OS 9 Only) After you click Install in the Nikon Capture Installer dialog, a dialog will be displayed asking whether you wish to create aliases for Nikon Capture 4 Editor and Nikon Capture 4 Camera Control on the desktop. Click Yes to create these aliases, or No to exit without creating aliases.
Installing Nikon Capture 4 on a Macintosh 2.1.6 Selecting a Plug-ins Folder (Mac OS 9) If multiple copies of Photoshop are installed, a selection dialog will be displayed. Choose a destination for the Nikon NEF plug-in from the listed copies of Photoshop and click Continue. 2.1.7 Personalize your copy of Nikon Capture 4 Enter your name and company (if applicable) to personalize your copy of Nikon Capture 4. Clicking OK will display a conrmation dialog; if the information you entered is correct, click Yes to proceed to the next step. To change the information you entered, click No. 2.1.8 Choose default color management settings To use the color-space prole embedded in images opened in Nikon Capture 4, choose (A) Use the color space of the le to be opened as the working color space for Nikon Capture 4. To choose a default RGB color-space prole for the working color space in Nikon Capture 4, choose (B) Always use the default RGB color space set below as the working color space for Nikon Capture 4. Click OK to put changes into effect and proceed to the next step. When (B) Always use the default RGB color space set below as the working color space for Nikon Capture 4 is selected, the ColorSync settings button will be active. Click this button to display the ColorSync dialog. After opening the Default Proles tab (Mac OS X) or opening the Proles tab and selecting Default Proles for Documents (Mac OS 9), choose the default working RGB color space from the RGB Default menu.

Mac OS X

Mac OS 9
Macintosh Clicking Color space details displays a description of the different color-space proles. Use this explanation to help you choose a color-space prole.
The default output color-space prole can be changed at any time after installation in the Color Management tab of the Nikon Capture 4 Editor or Nikon Capture 4 Camera Control Preferences dialog. 2.1.9 Complete installation of Nikon Capture 4 The following dialog is displayed when installation of Nikon Capture 4 is complete. Click Quit to proceed to the next step.
Add to Dock (Mac OS X) The dialog shown at right will be displayed when Nikon Capture 4 Editor and Nikon Capture 4 Camera Control are installed. Click Yes to add these components to the Dock, or No to exit without adding these components to the Dock.
Installing Nikon Capture 4 on a Macintosh 2.2 Restart the computer Click Restart to restart the computer.
Before connecting your camera to a Macintosh computer for the rst time, make sure that you install Nikon Capture 4. After installing Nikon Capture 4, turn the camera on and connect it to the computer, or insert the memory card into a card reader or a PC card slot. For more information about connecting your camera to a computer, see the documentation provided with your camera. D1-Series ( Firewire Interface)
D2-Series/D200/D100/D70s/D70/D50 (USB Interface)
Connecting to a Computer Using a PC Card Slot When inserted in a PC-card adapter (available separately), the camera memory card functions as a Type II PCMCIA ATA card, allowing images to be read from the card. Inserting a Memory Card Remove the memory card from the camera and insert it in the adapter.
Uninstalling Nikon Capture 4 This section describes how to uninstall the Macintosh versions of Nikon Capture 4.
Insert the Nikon Capture 4 CD into a CD-ROM drive and start the Nikon Capture 4 installer as described on pages 7273 of Installing Nikon Capture 4 on a Macintosh. Select Uninstall from the menu at the top left corner of the Nikon Capture Installer dialog.
Click the Uninstall button at the bottom right corner of the Nikon Capture Installer dialog. Once Nikon Capture 4 has been removed from your system, the dialog shown below will be displayed. Click OK.