746 Dorian M. Raymer Douglas E. Smith
Department of Physics, University of California, La Jolla, CA, USA
Electrophoresis 2007, 28, 746748

Research Article

A simple system for staining protein and nucleic acid electrophoresis gels
Researchers in molecular biology spend a significant amount of time tending to the staining and destaining of electrophoresis gels. Here we describe a simple system, costing ,$100 and taking ,1 h to assemble, that automates standard nucleic acid and protein gel staining protocols. Staining is done in a tray or, with DNA gels, in the electrophoresis chamber itself following automatic detection of the voltage drop. Miniature pumps controlled by a microcontroller chip exchange the necessary solutions at programmed time intervals. We demonstrate efficient and highly reproducible ethidium bromide and methylene blue staining of DNA in agarose gels and Coomassie blue and silver staining of proteins in polyacrylamide gels. Keywords: Destaining / DNA / Electrophoresis / Protein / Staining DOI 10.1002/elps.200600325
Received May 26, 2006 Revised August 7, 2006 Accepted August 17, 2006

Introduction

Gel electrophoresis is a powerful and ubiquitous method for analysis of DNA, RNA, and protein samples. One of the few downsides of this technique is that it is time consuming. Indeed, significant efforts have been made to developing more rapid processing methods such as CE and lab on a chip systems [1, 2]. While such methods are promising, the majority of researchers nevertheless continue to use classical techniques, which are often favored on the basis of their familiarity, reliability, and low cost. Given the wide use of these established techniques, simple improvements in their implementation may be of great value. Staining of gels involves time-consuming manual processing steps. A researcher must repeatedly return to the bench to change solutions. The situation becomes burdensome when one wants to process multiple gels of different types in parallel with different starting times. Standard protocols are given in reference books such as Molecular Cloning: A Laboratory Manual [3] and Short Protocols in Molecular Biology [4]. Ethidium bromide staining of DNA in agarose gels typically involves removing the gel from the electrophoresis chamber, incubating it in the staining so-
Correspondence: Professor Douglas E. Smith, Department of Physics, University of California, San Diego, 9500 Gilman Drive, La Jolla, CA 92093, USA E-mail: des@physics.ucsd.edu Fax: 11-858-534-3501
lution for ,20 min and then in water for 3060 min to destain, with several solution changes often being recommended to achieve the highest sensitivity. Effective staining of DNA gels with methylene blue, preferred by some for its low toxicity and capability for visualization without UV light, generally requires thorough destaining for good results. Polyacrylamide protein gels are often visualized with Coomassie blue or silver staining. Silver staining, in particular, involves a large number of processing steps that require accurate timing. A typical protocol that works well in our experience calls for incubation in a fixing solution for 15 min, in water three times for 5 min, in a sensitizing solution for 15 min, again in water three times for 5 min, in silver nitrate for 30 min, in water and developer solution for 1 min, in developer for ,10 min, and finally addition of a stopping solution. Here we describe a simple system for automating such protocols. We programmed a microcontroller chip to actuate miniature fluid pumps to add and remove solutions at specified time intervals. The system was built from inexpensive off-the-shelf components. While several commercial systems for automating certain gel staining protocols are available (e.g., from Amersham and BioRad), these systems are ,50 times more expensive than the one described here and are less flexible. Furthermore, we describe a novel method whereby horizontal slab gels may be automatically stained in the electrophoresis chamber following automatic detection of the voltage drop at the end of electrophoresis.

2007 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim
www.electrophoresis-journal.com

General

Materials and methods
2.1 Instrument design Our system is shown schematically in Fig. 1. Model aircraft fueling pumps were used because of their low cost ($15 each) and chemical resistance. The pumps were arranged to transfer solutions between reagent bottles and the staining chamber via silicone tubing. One pump was used as a circulator to periodically flow the solutions over the gel to insure efficient mixing. With larger gels, we found that the best results were obtained by using two circulators and arranging the tubing to spray the solutions across the width of the gel. Also we found it helpful to sandwich the gel between two screens to prevent it from folding during the staining and destaining process. Further details and a diagram are given in the Supporting Information. We note that this method eliminates the need for agitation by a shaker, which typically costs ,106as much as our entire system. We programmed an inexpensive microcontroller chip (PIC 16F628A, cost: $2) to switch the pumps on and off at specified time intervals. The microcontroller was mounted on an inexpensive preassembled circuit board that provides relay switches and an interface for programming. Programs were written in Basic and compiled into machine code. A detailed parts list, assembly instructions, and program codes are given in the Supporting Information.
Agarose slab gels (769 cm2) were run in a horizontal mini-gel system (Fisher Scientific #FB-SB-710). SDS-PAGE mini-gels (1067 cm2) were purchased from BioRad and run in a vertical mini-gel system (BioRad Mini Protean III system). Larger 16616 cm SDS-PAGE gels were purchased from BioRad and run in a vertical system (BioRad Protean II system). Protein mini-gel staining was done in the lid of a pipette tip box (13611.5 cm2, filled with ,150 mL of solution) (Fisher Scientific #02-707-325), the larger PAGE gels in a tupperware container (19632 cm2, filled with ,600 mL of solution), and DNA gel staining was done in the electrophoresis chamber (Fisher Scientific #FB-SB-710, filled ,300 mL of solution). Ethidium-stained gels were visualized on a UV transilluminator and methylene blue gels with a white-light converter plate and photos were taken with a Nikon Coolpix 995 digital camera. SDS-PAGE gels were imaged with a Canon Canoscan 3000ex scanner.

Results

3.1 Nucleic acid gels To demonstrate that our system could stain agarose DNA mini-gels, we implemented ethidium bromide and methylene blue staining protocols, as described in Supporting Information. As shown in Fig. 2, our system gave results comparable to those obtained when staining gels manually. To demonstrate automatic staining in the electrophoresis chamber following the completion of electrophoresis, we wired the electrophoresis power supply to an opto-isolated digital input sensor on our circuit board. The microcontroller was then programmed so that staining and destaining began immediately after the end of the electrophoresis run was detected. The gels shown in Fig. 2 were processed in this manner. In this method, the gel sits in the horizontal electrophoresis chamber after running, and the staining and destaining solutions are circulated over the top surface of the gel to facilitate even staining. This approach allows the user to simply start an electrophoresis run and return later to retrieve the stained and destained gel. If desired, one may also use a separate staining tray. 3.2 Protein gels
Figure 1. Schematic diagram of the system. Pumps actuated by a microcontroller add, circulate, and remove reagents from the staining chamber.
2.2 Reagents and electrophoresis equipment Agarose, Tris-acetate-EDTA (TAE) buffer, Tris-glycine-SDS (TGS) buffer, ethidium bromide, methanol, acetic acid, Brilliant blue R-250, silver nitrate, formaldehyde, citric acid, and sodium thiosulfate were purchased from Fisher Scientific. Methylene blue and sodium carbonate were purchased from Sigma. l DNA HindIII markers were purchased from Promega. PageRuler unstained protein markers were purchased from Fermentas.
We implemented standard Coomassie blue and silver staining protocols for SDS-PAGE mini-gels, as described in Section 2 and in Supporting Information. Photographs of processed gels are shown in Fig. 3 and indicate good results. As discussed above, silver staining involves many time-sensitive steps and particularly showcases the advantage of the automated system. Seven pumps were programmed to automatically deliver, circulate, and drain the fixing, rinsing, sensitizing, silver nitrate, developing, and stopping solutions.
D. M. Raymer and D. E. Smith
Figure 2. Comparison between agarose DNA mini-gels stained manually and automatically. (A) Ethidium bromide, with 250, 130, 60, and 30 ng of l HindIII marker. (B) Methylene blue, with 1500, 750, 400, and 200 ng of l HindIII marker.
Figure 3. Comparison of SDS-PAGE protein mini-gels stained manually and automatically. Results with larger format SDSPAGE gels were similar and are shown in the Supporting Information. (A) Coomassie blue, with 360, 180, 90, and 45 ng of protein marker. (B) Silver-stained with 60, 30, 15, and 7.5 ng of protein marker.

Discussion 5 References

We have demonstrated a simple and inexpensive system for staining of nucleic acid and protein electrophoresis gels, thus automating a time-consuming task that is often done manually by researchers in molecular biology. The automated system yields results as good as those achieved manually and with increased reproducibility. Ready-to-use program codes for ethidium bromide, methylene blue, Coomassie blue, and silver staining are provided in the Supporting Information. The programs can be easily modified to implement other protocols. As this system is very inexpensive it is also practical to set up multiple stations for processing many gels with different protocols in parallel.
[1] Hawtin, P., Hardern, I., Wittig, R., Mollenhauer, J. et al., Electrophoresis 2005, 26, 36743681. [2] Landers, J. P., Anal. Chem. 2003, 75, 29192927. [3] Sambrook, J., Russell, D. W., Molecular Cloning: A Laboratory Manual, 3rd Edn., Cold Spring Harbor, New York 2001. [4] Ausubel, F. M., Brent, R., Kingston, R. E., Moore, D. D. et al., Short Protocols in Molecular Biology, 5th Edn., John Wiley, Indianapolis, JN 2002.

COLOUR FLATBED SCANNER

Making scanning fast, fun & easy
USB 2.0 Hi-Speed interface 1200 x 2400 dpi CCD sensor and 48-bit internal colour depth 3 configurable EZ buttons Software: ArcSoft PhotoStudio & PhotoBase, Caere OmniPage SE Fast Multi-Photo mode Advanced Z-lid for book or magazine scanning QARE dust and scratch removal for photos

TIME-SAVING SPEED

Meet all your scanning needs easily with the fast yet affordable CanoScan 3000ex. A USB 2.0 Hi-Speed interface transfers data between your scanner and PC at amazing speed, making it perfect for high resolution scanning.
COMPLETE EASE OF USE HIGH IMAGE QUALITY
Whether you're scanning photos or documents get great results every time, thanks to Canon's innovative technology and unsurpassed optical expertise. 48-bit internal colour depth delivers exceptional colour accuracy whilst 1200 x 2400 dpi resolution captures the sharpest details. Freshen up old photos with a single click - QARE (Quality Automatic Retouching & Enhancement) removes dust and scratches, producing scans of photos that look as good as the day they were taken. Three 'EZ' buttons can be configured to simplify standard tasks, so with just one touch you can scan images directly to a file, copy them or send them straight to your email programme. Canon's advanced Z-lid, with a double hinge, allows easy scanning of thick documents and books.

FAST MULTI-PHOTO SCANS

Scan multiple photos in a single operation. Skewed images are straightened automatically. They can then be filed, forwarded as email attachments or printed directly. It's the simplest and most efficient way to scan multiple photos - and Hi-Speed USB processing saves you even more time.
PRACTICAL, POWERFUL SOFTWARE
Enhance creativity with Canon's comprehensive software package. This includes practical ArcSoft PhotoStudio & PhotoBase for image editing and management and Caere OmniPage SE for converting scanned documents to text.

Scan 1 Scan 3

Scan One scan run without Multi-Photo mode.
Scan 2 One scan run on the CanoScan 3000 ex with Multi-Photo mode.

CanoScan 3000 ex

Type Scanner Element Light Source Optical Resolution Selectable Resolution1 Interface Scanning Gradation Maximum Document Size Preview Speed Scanning Speed2 Power supply Power Consumption Dimensions Weight Operating Range Desktop Colour Flatbed Scanner CCD Cold cathode fluorescent lamp dpi 25 - 9600 dpi USB 2.0 Hi-Speed Color 48 bit input / 24 bit output Greyscale 16 bit input / 8 bit output A4 / letter, 216297 mm Approx. 8sec Colour, Greyscale, B&W 4 msec/line (600 dpi) 8 msec/line (1200 dpi) AC Adaptor3 15W Max, 5W Stand-by 257 x 460 x 61mm Approx 2.4kg Temparature 10 - 35C Humidity 10 - 90% RH, without condensation formation OPERATING SYSTEM REQUIREMENTS For USB 2.0 Hi-Speed Windows 2000 Pro, ME, XP (Home/Pro) For USB Windows 98, 2000 Pro, ME, XP (Home/Pro) CPU: Intel PIII, Celeron (566 Mhz or higher). AMD Athlon, Athlon MP/XP, Duron. 128MB RAM, USB port4 , CD ROM drive.
CPU: Pentium II 233Mhz or higher. 64MB RAM (128MB for WinXP). USB port4(standard equipped port), CD ROM drive.
Increased resolution is a function of the ScanGear CS driver USB 2.0 Hi-Speed mode. Scan time only, data transfer time not included AC Adaptor types vary by region Standard equipped port. Additionally the following Adaptec cards & hubs have been tested and approved for compatibility: USB2connect 2000LP/3100LP/5100, DuoConnect
All Specifications subject to change without notice. CanoScan and ScanGear are trademarks of Canon Inc. Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries All brand and product names are trademarks of their respective companies. Specification CEL 1.0 310304
Canon Inc www.canon.com Canon Europa NV www.canon-europe.com
0042W134 Canon Europa NV 2004 (0404)