Benefits: - Quick response time - High contrast ratio - Build-in Speakers
20ms response time Offers dynamic graphics and advanced animated games 500:1 contrast ratio For strikingly vivid images Built-in speakers For freedom from bulky boxes Brightness up to 250 cd/m2 Provides crisp, sparkling images Kensington lock Secures your monitor from theft Auto-scale Gives full-screen display Auto-adjustment Provides self-adjusting screen settings True colour support Renders picture-pure viewing

Specifications

Model Size Maximum resolution Colour Viewing angle Contrast Brightness Response time Input signal Power supply Power consumption Dimensions (WxHxD) VESA wall mounting Net weight Other features Acer AL716 17" 1280 x 1024 16.7M Horizontal: 160; Vertical: 130 500:1 250cd/m 20ms Analogue VGA 100-240V 54W (max.) 374 x 395 x 204 mm 75 x 75 mm 5.9kg Speakers; Kensington lock

1.2 Description

The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF target is 20k hours or more. Comparison Chart of AM777 (AL712)/778/677(AL716)/678(AL711)
Panel AM778 Normal 17 panel AU M170EN05 AM777 (AL712) Normal 17 panel AU M170EN05

Hydis HT17E12-200

Signal Interface Sync Type for analog input DSUB+DVI-D Separate / compatible / Support DDC2B No No No Not support Yes / No Option AM678 (AL711) Normal 17 panel AU M170EN05 Samsung LTM170EU-L02 DSUB Separate / compatible / Support DDC2B No No No Not support Yes / No Option
DSUB+DVI-D Separate / compatible / Support DDC2B 1W+1W Yes No Not support Yes / No Option AM677 (AL716) Normal 17 panel AU M170EN05 Samsung LTM170EU-L02 DSUB Separate / compatible / Support DDC2B 1W+1W Yes No Not support Yes / No Option
Color Temp user adjust DDC
Speaker Headphone Jack Microphone Jack USB Hub Tilt / Swivel Height Adjust
Signal Interface Sync Type for analog input
2. ELECTRICAL REQUIREMENTS
2.1 Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified. Ambient light: 225 lux Viewing distance : 50 cm in front of LCD panel Warrn up time All specifications: 30 minutes Fully functional: 5 seconds Measuring Equipment: Chroma 2250 signal generator or equivalent, directly Connected to the monitor under test. Minolta CA100 photometer, or equivalent Control settings User brightness control: Maximum (unless otherwise specified ) User contrast control: Typical (unless otherwise specified ) User red/white balance, Green/white balance and Blue/white balance control: In the center (unless otherwise specified ) Power input : 110Vac or 230Vac Ambient temperature : C ( F) Analog input mode : 1280 x1024 /60 Hz 2.1.1 MEASUREMENT SYSTEMS
The units of measure stated in this document are listed below: 1 gamma = 1 nano tesla 1 tesla = 10,000 gauss cm = in x 2.54 lb = kg x 2.2 degrees F = [C x 1.8] + 32 degrees C = [F - 32]/1.8 u' = 4x/(-2x + 12y + 3) v' = 9y/(-2x + 12y + 3) x = (27u'/4)/[(9u'/2) - 12v' + 9] y = (3v')/[(9u'/2) - 12v' + 9] nits = cd/(m2) = Ft-L x 3.426 lux = foot-candle x 10.76

2.2 LCD monitor General specification
Panel Type : 17 active matrix color TFT LCD 1). Hydis LT17E12-200 Display size : 337.92mm(H) x 270.34mm(V) Display mode : VGA VGA SVGA 720 X 400 (70 Hz) 640 X 480 (60/66/70/72/75 Hz) 800 X 600 (60/70/72/75 Hz) 4
XGA 1024 X 768 (60/70/75 Hz)
SXGA 1280 X 1024 (60/70/75 Hz) Pixel pitch : Display Dot : Pixel Clock : Contrast ratio: = 0 Brightness: Response time (Tr/Tf) : Display color : Viewing angle: L / R U/D Luminance Uniformity : Pc interface: 1). Video : Sync : Signal connector : 0.098x3mm(H) x 0.294mm(V) 1280 x (RGB) x 1024 25.2 135.0MHz 430 : (typical) cd/m2 (typical)

standard resolution

20 /20 msec 16777216 (8 bite color) > 80 % RGB analog 0.7V peak to peak TTL positive or negative 15 pin Mini D type, (standard VGA video) DVI-D connector 3.5 mm stereo audio jack(Audio)(AM777/677) 3.5 mm miniature stereo Headphone jack(AM777/677) / 80 / 65 ( 160 degrees horizontal typical) ( 130 degrees vertical typical)

2). Digital TMDS

Audio power : (AM777/677) Front control : Interface frequency
1Wrms + 1Wrms ( 300Hz 10kHz (S.P.L. 10 dB)) power on/off with LED select (up, down) adjustment (+,-)
Horizontal Frequency 24KHz --80KHz(analog), 31.5 80KHz(digital) Vertical Frequency Plug & play : Power Input voltage : Total output power : 56Hz ----75Hz Support VESA DDC2B functions Single phase, 50/60HZ, 100VAC to 240VAC 10% 48 Watt max.
2.3 LCD Panel Specification
2.3.1 LCD Panel Model (Hydis LT17E12-200)
Display Type Resolution Display Dot Display Area 5
active matrix color TFT LCD 1280 x 1024 pixels 1280 x (RGB) x1024 337.92mm(H) x 270.23mm(V)
Optical Specifications IL = 6.5mA (RMS) Ta = 25 2C ITEM Symbol Contrast Ratio CR (Center of screen) Response Rising TR Time at Ta Falling TF Luminance of white YL (Center of screen) RX Red RY Color Chromaticity (CIE) Green Blue White Viewing Angle Hori. Vert. GX GY BX BY WX WY L R H L BUNI F CT
Pixel Pitch Display Color Lamp Voltage Lamp Current Weight VDD = 5V Condition

0.264mm(H) x 0.264mm(V) 16M (6bite color+FRC) 700Vrms (typ) 6.5mArms (typ) 1900g (typ) FV = 60HZ FDCLK = 54MHZ MIN. TYP. MAX. 350 =0, =0 Normal Viewing Angle 200 0.599 0.324 0.257 0.568 0.115 0.073 0.270 0.0.354 0.287 0.598 0.145 0.103 0.300 0.65 _ 30 0.659 0.384 0.317 0.628 0.175 0.133 0.330 0.365 1.2.0 (total) msec cd/m2

Degrees

Brightness Uniformity Flicker Cross talk 2.3.2 LCD Panel Model
(AU M170EN05) active matrix color TFT LCD 1280 x 1024 pixels 1280 x (RGB) x 1024 337.92mm(H) x 270.34mm(V) 0.264mm(H) x 0.264mm(V) 262K (6 bit color) 700 Vrms typ. 7mA rms.( typ). 4 Lamp 2000g.
Display Type Resolution Display Dot Display Area Pixel Pitch Display Color Lamp Voltage Lamp Current Weight Optical Specifications
The following items are measured under stable conditions. The optical characteristics should be measured in a dark room or equivalent state with the methods shown in Note(4). Measuring equipment : TOPCON BM-5A, BM-7, PHOTO RESEARCH PR650
(Inverter Freq. : 54kHz) *Ta =25 2C, VDD=5V, fv=60 Hz, fDCLK=54 MHz, IL= 6.5mArms
Contrast Ratio (Center of screen) Rising Response Time Falling Luminance of White (Center of screen) Red Color Chromaticity (CIE 1931) Green Blue White Hor. Ver.

Symbol

CR TR TF YL Rx Ry Gx Gy Bx By Wx Wy

Condition

4.0.64 0.34 0.29 0.61 0.14 0.07 0.31 0.80 -

(1)(2)(4) BM-5A

msec cd/m2

(1)(3) BM-7 (5) BM-5A

Normal = 0 = 0 Viewing Angle

TYP. -0.03

TYP. +0.03

(1)(4) PR650

Viewing Angle

L R H L

(1)(4) BM-5A
Brightness Uniformity (9 points)

(6) BM-5A

Note 1) Definition of Viewing Angle: Viewing angle range (10CR)
Note 2) Definition of Contrast Ratio (CR): Ratio of gray max(Gmax),gray min(Gmin) at the center point of panel. 7
Luminance with all pixels white (Gmax) Luminance with all pixels black (Gmin)
Note 3) Definition of Response time: Sum of TR , TF
Note 4) After stabilizing and leaving the panel alone at a given temperature for 30 min, the measurement should be executed.Measurement should be executed n a stable, windless ,and dark room.30 min after lighting the back-light. This should be measured in the center of screen. Dual lamp current :13.0mA(6.5mA x2)(Refer to the note(1) in the page 14 for more information ). Environment condition :Ta=252C
Optical characteristics measurement setup
Notes 5) Definition of Luminance of White : measure the luminance of white at center point.
Notes 6)Definition of 9 points brightness uniformity (Measuring points: Refer to the Note 5) Bmin BUNI=100 Bmax Bmax: Maximum brightness Bmin: Minimum brightness Notes 7) Definition of Flicker level F Flicker Voltage pp = x 100 % LMD Voltage dc

One maximum value of three estimated values. For this test ,an LMD(Light Measurement Device)is needed with adequate response time to track any visible rate flicker component and with a voltage level output proportional To luminance intensity. Test Pattern: For dot inversion Driving(Gray levels of foreground dots on the test panel Are G22,G32,and G45) Test Point :Center point of the display area
Note 8) Definition of Crosstalk (Refer to the VESA STD)
The calculation for shadowing is made from the 2 luminance measurements Gbkg and Lsh, as follows: Lmax -Lmin CT = x100 % Lmin Where Lmax is the larger value of Gbkg or Lsh , and Lmin is the smaller of the two. To determine background and foreground levels (colors),first set the background to any gray scale or color level suitable for shadowing determination.(Note that it may take several iterations of adjusting background level and box levels to determine the proper value for the background.Next display the box levels to determine the proper value for the background level. Look for shadowing in any direction from box E. Independently vary the gray level (or color) of the background and box E until the worst case shadowing is observed. This defines the background (Gbkg) and foreground (Gfg) levels to be maintained for the remainder of the test. One point only (the target) will be measured. To determine that point proceed as follows Using the background and foreground gray levels of step1 (Gbkg and Gfg). Turn on each box at a time. Look for the case with the worst shadowing. The box causing the worst case is the shadowing source, or Bsrc. Use Bsrc and the box opposite from it that lies directly in the shadow path. That is the target box, or Btgt. Note that box Eight be either Bsrc or Btgt, depending on the shadowing conditions, but typically Bsrc and Btgt will be a pair of opposite boxes, A&C or B&D. Btgt will only be displayed for aligning the LMD. It will be turned off for the actual measurement. The target box point (Btgt) will be measured with the source box (Bsrc) turned on then off. (Btgt is for alignment purpose only) Display the background only at level Gbkg. Display Btgt determined in step 2 above. Using the correct distance, angle, and measurement aperture, align the LMD to the center of the Btgt. Turn off Btgt. With Gbkg set to its proper level, measure the luminance (or color). Next,turn on the source box Bsrc. Again measure at the center point of Btgt (without Btgt present.). In this case the LMD will be measuring the shadowing level, Lsh.

31.5 31.5 28.322 57.2832

50 49.71.78.75 80
If the input timing is not a supported timing listed above but within the supported frequency range (Horizontal: 80KHz,Vertical: 75Hz), this monitor will select a closest mode instead. But the display quality may not be optimized. If the input timing over the supported frequency range, a message Input Signal Out of Range will be shown.
2.4.4 85Hz refresh rate Support Monitor should display 85Hz refresh rate mode as emergency mode. Monitor should display Out of Range warning menu at this mode. 2.4.5 Video input Connector
Analog Video input Connector: 15pins mini D-Sub PIN NO. 15 Table 2.4.5. Pin assignment for D-sub connector Separate Sync RED VIDEO GREEN VIDEO BLUE VIDEO GROUND GROUND RED GROUND GREEN GROUND BLUE GROUND PC5V (+5V DDC) CABLE DETECTION GROUND SDA H.SYNC V.SYNC SCL
Color of plastic parts: Blue (PC99)

D-sub connector

Digital Video input Connector: DVI-D (T.B.D) Table 4-3-3. Pin assignment for DVI-D (24pin) connector
Pin Assignment of DVI D connector : TX29 TX1TX2+ 10 TX1+ Shield (TX2 / TX4) 11 Shield (TX1 / TX3) NC 12 NC NC 13 NC DDC-Serial Clock 14 +5V power *) DDC-Serial Data 15 Ground (+5V) No Connect 16 Hot plug detect
TX0TX0+ Shield (TX0 / TX5) NC NC Shield (TXC) TXC+ TXC-
*) In case, the power of the PC unit is switched off and the power of the monitor is switched on, no voltage may occur at pin 14.

2.5 CONTROLS

2.5.1 Control panel (monitor front panel) 1. Stereo Speakers (AM777/677) 2. Speaker Volume Control (AM777/677) 3. Soft Power Switch 4. DC Power-On Indicator 5. Function select Buttons 6. Adjustment Control Buttons 7. External Headphone Jack(AM777/677) Note: When OSD Menu is off, press button 2 and 3 at the same time can activate Auto Adjustment immediately. 2.5.2 OSD Functions
OSD Format: OSD Border: OSD Tunable Item: Selected Item: Comment:
Refer to following figure. Cyan color The 16 icons that around the border. Yellow background Magenta foreground, Blue background

page format :

Description:
Brightness: Contrast: H. Position: V. Position: Phase: OSD position: Auto Adjustment:
Brightness adjustment, the range from 0 to 100. Default = 100 Contrast adjustment, the range from 0 to 100. Default = 50 Horizontal position adjustment. Vertical position adjustment. Focus adjustment, the range from 0 to 255 steps. OSD position adjustment. This feature will automatically adjust size, position, clock and phase. It takes 3-5 seconds to finish. When auto start, it shows Auto Adjusting. message.

Clock: Graph Text: Language: Recall: Color Temp:
User: User R: User G: User B: 7500: 6500: 9300:
Frequency tracking adjustment. The max range from -50 to +50, but some modes the range will be limited. 640x400(GRAPH) or 720x400(TEXT) mode select. 5 kinds of language for description, including (English, German, French, Spanish, Italian) Recall the default value. Color temperature for standard 9300,6500, 7500 or user defined. Red signal gain by user defined. Green signal gain by user defined. Blue signal gain by user defined. Set CIE coordinate at 7500K color temperature. Set CIE coordinate at 6500K color temperature. Set CIE coordinate at 9300K color temperature. Exit OSD menu function.

Exit:

Sharpness : Adjust the scale-up effect(smoother or sharper.) OSD Transparency: Adjust the transparency level of OSD. The range is from 0 to 100 scales. Comment:
1280x1024: 60 HZ: VER 1.00:
Current mode resolution. Current mode vertical frequency1Hz. Firmware revision.

Other features: 17

Intellectual-Auto AM777/778/677/678 can start the Auto-Adjustment automatically when input a new display mode at first time. After the adjustment, AM777/778/677/678 will remember this mode and switch to optimized condition automatically for this mode whenever encounter this mode again. Total 27 recent used modes are recorded into EEPROM
VESA DPMS Functionality When signaled by the host CPU, AM777/778/677/678show a black screen about 3 seconds. If no further signal, then it shows No Signal and enter power saving mode.
2.6 White Color Temperature
White color temperature is 4 preset as 9300, 7500,6500 and User, Default value of user color should be user which is maximum setting for panel. Target of color setting Color Temp. 9300K 7500K 6500K User Color Coordinate x y 0.281 0.311 0.299 0.315 0.313 0.329 *) TCO0X A.2.6.1 requirement Tolerance +0.03 +0.03 +0.03 Color Coordinate u 0.189 0.194 0.198 v 0.446 0.459 0.469 Tolerance uv < 0.01* uv < 0.01* uv < 0.01* -
User should follow Microsoft Windows Color Quality Specification for Liquid Crystal Display OEMs. (http://www.microsoft.com/hwdev/tech/color/ColorTest.asp)

2.7 POWER SUPPLY

2.7.1 input Voltage Range
The monitor shall operate within specification over the range of 90 to 265 VAC power supply.
2.7.2 Input Frequency Range Input power frequency range shall be from 47.5 to 63 Hz over the specified input voltage range. 2.7.3 Quick specification review

Input current

1.2A (max) at 90VAC input and full load , 0.6A (max) at 264 VAC input and full load. Inrush current @ cold start 30A(0-peak)@ 110Vac ,50A(0-peak) @ 220Vac (measured when switched off for at least 10 mins.)

Output

Tolerance Output Volt +5Vdc +5Vdc +12Vdc 5% 5% 5% Output Current MIN 0A 0.05A 0A MAX 1.0A 1.5A 2.2A Volt Tolerance 4.8~5.2V dc 4.8~5.2V dc 11.4~12.6Vdc
Total output power: Withstanding voltage : Leakage current : Efficiency :
2.7.4 Power Management 2.7.4.1 Meet VESA DPMS proposal
48 Watt max. 1.5Kvac or 2.2KVdc for 1 minute. < 0.25mA/100Vac , <3.5mA/230Vac 80% min. @115V/230VAC, maximum load.
The monitor must comply with the Microsoft On Now specification, with a minimum of three power management states, as defined by the VESA DPMS document. The front panel of the monitor must appropriately display the DPMS state, For example:
DPMS ON : DPMS OFF : 2.7.5 Power Consumption
On mode Off mode DC power off Power SW off disconnection
The power LED is Green The power LED is Amber
48 Wmax 4 Wmax 4 Wmax 1 Wmax 4 Wmax Green Amber Dark Dark Dark (DC power off) Amber (DC power on)
Power saving states are measured with speakers attached but not worked. The recovery time from stand by /suspend/off mode to on mode is 3 seconds maximun. 19

Power Connector

All units shall have an IEC/CEE-22 type male power receptacle.
2.8 Plug & Play(EDID)
The monitor will be capable of sending a VESA standardized EDID file through the DDC (pins 12, 15 of the VGA connector).
2.9 Audio Technical specification (AM777/677 Only)
2.9.1 General Description: Output power Total harmonic distortion Input signal sensitivity Input impedance Frequency response range Difference of L and R output
: 1W + 1W maximum : Less than 1 % (except speakers distortion) : 0.5 Vrms for full output : 47 Kohm +/- 5 % : 100Hz 20kHz (except speakers response) : Less than 2 dB
2.9.2 Electrical characteristics (Tamb=25) Audio amplifier(USE Panasonic VP-7723A Audio Analyzor. ) Item
Input Voltage(V) Input Current(m A) Audio Voltage Gain Frequency Response Signal to Noise ratio Total harmonic distortion Cross talk Output Watt. Volume Control

Audio Input

Freq. Min.

Spec. Typ. Max.

800 6dB +10d B -40dB 1% -30dB 1W -

Comment

500m Vrms 1KHz 500m Vrms 300Hz-20KHz -10dB 500m Vrms 1KHz 500m Vrms 1KHz 500m Vrms 1KHz 500m Vrms 1KHz -
Volume Max.,load 4 Volume Max.,load 4 Volume Max.,load 4 except speakers distortion Volume Max.,load 4 Volume Max.,load 4 Analog
2.9.3 Speakers Maximum power Impedance Frequency response range Total harmonic distortion 2.9.4 Headphone output Output power : 1.6 mW for 32 ohms Headphone : 1 W per speaker(max) : 4 ohm +/- 15 % @ 1kHz 1.0Hz : 300 Hz 20 kHz (S.P.L. 10 dB) : Less than 5 % @ 0.125 W 1kHz
3. VL-713 DISPLAY CONTROL BOARD

3.1 Description

The VL-713 display control board is design to directly receive R, G, B Analog and TMDS DVI signal to optimum LCD timing signals so as to construct a high display quality LCD monitor.
3.2 Features Support for image expansion and reduction. On board micro-processor to detect display timings and control user functions. Using Genesis design to generate optimum LCD timings. Using E2PROM to memorize every adjusted parameter. Support up to 25 display modes from VGA to SXGA. Support up to 5 display modes from VGA to SXGA by TMDS. Offer full screen expansion function on non-XGA mode (automatic). Support OSD functions. Support VESA DPMS function. Support DDC1/2B functions. Support English and Japanese language for OSD description. The longest time for mode change is 3 seconds.

3.3 BLOCK DIAGRAM

System Block Diagram

3.4 Connector Locations

3.5 Connector Type
Location CN1 CN4 CN6 CN5 CN302 CN301 CN2 3.6.1 CN1
Pin # Signal Name RX2RX2+ Description TMDS negative differential TMDS positive differential output, channel 2 Shield for channel 2 do not connect do not connect DDC2B clock DDC2B data TMDS Pin # Signal Name HTPLG RXODescription +5V Supply TMDS negative differential output, channel 0 TMDS positive differential output, channel 0 shield for channel 0 do not connect do not connect Shield for TMDS clock TMDS negative differential output, reference clock TMDS positive differential output, reference clock TMDS
Type DVI-D 96113-0803 4501-10 98210-4011 98115-0313 4300-11P D-SUB
Maker FEMALE E&T E&T E&T E&T E&T E&T

4. VK-713 Control Panel Board

4.1 Description

The VK-713 is designed to offer a user interfaced control panel which passes and receives signals to and from VK-713 display control board.
4.2 Connector and Switch Locations

4.3 Connector type

Location J4 J2 J1 J3 JP1 Type 4301-08 4301-11 87502-0200 87502-0200 SCJ-0348-C Maker E&T E&T ACER ACER SC Number of pins 9
4.4 Connector pin Assignment
4.4.1 J4 Pin NO. 4.4.2 J2 Pin NO. Signal KEY-LEFT KEY-RIGHT KEY-DOWN KEY-UP KEY-POWER GND LED-G LED-Y Comment Function select counter-clockwise key Function select counter-clockwise key Adjust down key Adjust up key Power ON/OFF key GND Power is ON Power is OFF
Signal +5 VDD Volume L OUT+ L OUTAGND HP-S HP-L HP-R
Comment Volume Control Volume Control Audio Output L+ Audio Output LAudio GND Audio Earphone sensor Audio Earphone Output L Audio Earphone Output R 26
11 4.4.3 J3 Pin NO. 4.4.4 J1 Pin NO. 1 2

AGND R OUTR OUT+

Audio GND Audio Output R+ Audio Output R-
Signal L+ OUT L- OUT Signal R+ OUT R-OUT
Comment Audio Output L+ Audio Output LComment Audio Output R+ Audio Output R-

4.5 Switch definition

Location S1 S4 S5 S2 S3 Definition Power ON/OFF Function select by clockwise direction Function select by counter-clockwise direction Adjust up Adjust down Definition Green for ON mode; Yellow for OFF mode; yellow for Power Saving mode; Dark for DC power OFF mode.

4.6 LED definition

Location D1
5. POWER SUPPLY & INVERTER BOARD

5.1 Description

The Power supply and Inverter board is designed for Display control board and lighting up the back-lights of LCD module.
5.2 Power supply ( AC to DC section)
5.2.1 input Voltage Range
5.2.2 Input Frequency Range Input power frequency range shall be from 47.5 to 63 Hz over the specified input voltage range. 5.2.3 Quick specification review
5.3 Inverter (DC to AC Section) 5.4 Electrical characteristics
5.4.1 FOR AU PANEL M170EN05
MIN. INPUT VOLTAGE INPUT CURRENT Normal BACKLIGHT VOLTAGE LAMP CURRENT DRIVING FREQUENCY EFFICIENCY Vin ON/OFF sequence OLP TIME BRIGHTNESS RANGE Brightness control Brightness Strike voltage at 0C Operating life time PWM dimming frequency Note: 11.4V --------------3mA rms. 40KHz ---------------------30% 0.4V _ 1700 Vrms 30,000 hrs 160Hz TYP. 12.0V 2A 700V rms. 7mA rms 50KHZ 75% 0.5S 1S -------_ 260cd/m2 _ _ 180Hz MAX. 12.6V --------------7.5mA rms 80KHz --------------_ 100% 3.3V _ _ _ 200Hz (note) 3.3V, brightness max. Open lamp protection time Vin = 12V,max brightness COMMENT 12V5% Vin=12V, Vbrite=3.3V

Life time (hr) can be defined as the time in which it continues to operate under the condition: Ta=252C, IL =7 mArms until one of the following event occurs: 1. 2. When the brightness becomes 50 % When the startup voltage (Vs) at 0C becomes higher than the maximal value of Vs specified above.

5.5 Connector locations

5.5.1 Connector type
Location J970, J971, P803 P801
Type SM04(4.0)B-BHS-1-TB 96113-1203 SA-4S-066
Maker JST E&T AC Inlet

Number of pins 4 10P 3

5.5.2 Connector pin assignment 5.5.2.1 J970, J971 Pin NO. 3

Signal HV HV NC LV

Comment High voltage for lamp High voltage for lamp NC Low voltage (common)
5.5.2.2 J803 For Display control board (Interface) Pin NO. Signal Comment 3,4 +5Vaudio GND/Audio GND 30 +5Vdc for Audio ckt Ground for Audio ckt Common Ground

7 8,9,10

BRITE Sleep Enable Vcc
Brightness adjustable range: 0.4V<min>~3.3V<max> Power saving control(Active High) Normal:-0.3~1.0V. Sleeping:2.0~5.5V Backlight ON/OFF control (Active High) ON:1.5~5.5V OFF:-0.3~1.0V. +5Vdc supply to Interface BD, always on. Comment Audio Right Input Audio Left Input
5.5.2.3 P62 For AM777/AM677 Pin NO. Signal 3 Audio-RIN GND Audio-LIN
5.5.3 FOR HYDIS PANEL HT17E`12-200
MIN. INPUT VOLTAGE INPUT CURRENT Normal BACKLIGHT VOLTAGE LAMP CURRENT (every lamp) DRIVING frquency EFFICIENCY PWM dimming frequency Vin ON/OFF sequence OLP TIME BRIGHTNESS RANGE Brightness control Brightness Strike voltage at 0C Operating life time Operating life time Note: 11.4V --------------3mA rms. 30KHz -------160Hz --------------30% 0.4V _ _ _ 40,000 hrs TYP. 12.0V 2A 700V rms. 6.5mA rms -------75% 180Hz 0.5S 1S -------_ 250cd/m2 _ _ 50,000 MAX. 12.6V --------------7.5mA rms 70KHz -------200Hz -------_ 100% 3.3V _ 170Vrms 117Vrms _ (note) 3.3V, brightness max. Open lamp protection time Vin = 12V,max brightness Each CCFL COMMENT 12V5% Vin=12V, Vbrite=3.3V

5.6 Connector locations

5.6.1 Connector type
Location J940,J941,J980,981 P803 P801
Type BHSR-02VS-1 96113-1203 SA-4S-066

Number of pins 2 10P 3

5.6.2 Connector pin assignment 5.6.2.1 J920,J941,J980,J981 Pin NO. Signal HV LV Comment High voltage for lamp Low voltage(common)
5.6.2.2 J803 For Display control board (Interface) Pin NO. Signal Comment 3,6 +5Vaudio GND/Audio GND BRITE Sleep +5Vdc for Audio ckt Ground for Audio ckt Common Ground Brightness adjustable range: 0.4V<min>~3.3V<max> Power saving control(Active High) 32
Normal:-0.3~1.0V. Sleeping:2.0~5.5V 7 8,9,10 Enable Vcc Backlight ON/OFF control (Active High) ON:1.5~5.5V OFF:-0.3~1.0V. +5Vdc supply to Interface BD, always on. Comment Audio Right Input Audio Left Input
5.6.2.3 P62 For AM777/AM677 Pin NO. Signal 3 Audio-RIN GND Audio-LIN

6. TROUBLESHOOTING

6.1 Main Procedure
6.1.1 Power Circuit and Backlights Troubleshooting
6.1.2 Performance Troubleshooting
6.1.3 Function Troubleshooting
7. Power Line Transient Test (IEC 61000-4-4 Fast Transients/Burst)
TEST CONDITIONS & PROCEDURE: (Follow IEC 61000-4-4) Test Condition : The condition is base on operating with 50 load.

7.1 Peak Voltage:

2 KV (applies the Level 3 typical Industrial Environment of IEC 61000-4-4)

7.2 Polarity

7.3 Repetition Frequency of the impulse : 5 KHz. 7.4 Rise-Time : 5ns 30% 7.5 Impulse Duration: 50 nS 30% 7.6 Relation to Power Supply: Asynchronous 7.7 Burst Duration: 15 ms 20% 7.8 Burst Period: 300 ms 20% 7.9 Climatic Conditions:
- Ambient Temperature: 15C to 35C - Relative Humidity: 45% to 75% - Atmospheric Pressure: 86 kPa to 106 kPa

7.10 Test Procedure:

The monitor Display set high-resolution mode, AC input use AC 240V. Note : 7.10.1 IEC 61000-4-4 defines that power supply, I/O line, and control line all shall be performed the transient test, but the I/O line and control line is applied with only half of peak voltage (1 KV). 7.10.2 For the comparison of wave-shape generated by different generator, so the test must uses a scope with at least 400 MHz bandwidth, and coupled to 50 to monitor the rise-time, impulse, duration, and repetition rate of the impulses within one burst.

WAVESHAPE

8. Power Line Surge Test (IEC 61000-4-5 Surge)

8.1 Climatic Condition

The climatic conditions shall be within the following ranges: 8.1.1 Ambient Temperature: 15C to 35C 8.1.2 Relative Humidity: 10% to 75% 8.1.3 Atmospheric Pressure 86kPa(860 mbar)to 106kPa (1060mbar) Note: The temperature and relative humidity should be recorded in the test report.

8.2 Test Conditions:

8.2.1 Wave-shape of the current surge: (refer to IEC 61000-4-5) Open circuit voltage: (1.2 / 50 s) Short circuit current: 8.2.2 Polarity: (8 / 20 s)

positive / negative

8.2.3 Phase shifting:in a range between 0 to 270 versus the AC line phase angle 8.2.4 Repetition rate:at least 1 per minute 8.2.5 Number of tests: at least 5 positive and 5 negative at the selected points.
The surge will be applied between lines and between lines and ground.
If not otherwise specified, the surge to power supply circuits shall be applied synchronized to the voltage phase at the zero crossing and the peak value of the AC voltage wave. (Positive and negative)
The surge voltage for test is from 1 KV and increases 1 kV for each step.

The recommended severity levels for the surge voltage test is 2.0 KV, and without any degradation or loss of function that is not recoverable due to damage of component or software allowed.
Display set high-resolution mode, AC input use AC 240V.
9. ENVIROMENT REQUIREMENT

9.1 Operating

Temperature Relative Humidity Altitude 5C ~ 40C 20% to 80% Sea level to 8000ft

9.2 Storage or Shipment

Temperature Relative Humidity Altitude 9.2.1 TEST PROCEDURE: -20C ~ +60C 5% to 85% Sea level to 40,000ft
Put in temperature chamber under 60C Back to room temperature Put in temperature chamber under -20C Back to room temperature The process repeat 2 times.
Time:24 hours Time: 4 hours Time:24 hours Time:4 hours
10. REGULATION COMPLIANCE
10.1 This product comply to the most current revisions of following regulations:
UL/CUL {UL 1950/ CSA C22.2 NO950} EN 60950/CB Scheme MPR 1990:8 MPR 1990:10 EK1-ITB2000: NUTEK/EPA TCO 1999 (option) TUV/GS FCC 47 CFR, Chapter 1, Subchapter A, Part 15, Subpart B CISPR 22 CE LVD Directive (73/23/EEC) CE EMC Directive (89/336/EEC) Standard for Safety of Information Technology Equipment including Electrical Business Equipment Safety of Information Technology Equipment including Electrical Business Equipment Test methods for visual display units. User handbook for evaluation visual display units. Ergonomic requirements for office work with visual display terminals (VDTs)-Visual display requirements. Requirements of power saving according to NUTEK Spec. 803299/94/96, EPA Energy star. Requirements for Environmental Labeling of Personal Computers. Test methods for Ergonomic, Emission, Energy Efficiency, safety. Safety regulation for displays work places in the office sector. A digital device that is marketed for use in a residential environment not withstanding use in commercial, business and industrial environments. Limits and methods of measurements of radio interference characteristics of information technology equipment. Safety: EN60950 EMI: EN55022 class B Harmonics: EN61000-3-2 Voltage Fluctuation/Flicker: EN61000-3-3 Immunity: EN55024 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 Electrostatic Discharge Radiated Electromagnetic Field Fast Transients/Burst Surge Conducted Disturbance, Induced by Radio Frequency Fields IEC 61000-4-8 Power Frequency Magnetic Field IEC 61000-4-11 Voltage DIP/Interruption Specification for limits and methods of measurement of radio interference characteristics of information technology equipment. Class B conformity verification report from the VCCI CNS 13438, Class B

IEC 61000-4

VCCI (option)

BSMI (option)

10.2 Electrostatics Discharge (ESD)

E.S.D Test

This test follow the IEC 61000-4-2 Discharge Voltage Level : Criteria Class C Class B Class A Contact Discharge (KV) 8 Air Discharge(KV) 15
Class A : Temporary degradation or loss of function or performance which requires operator Intervention or system reset. Class B : Class C : Temporary degradation or loss of function or performance which is selfrecoverable Normal performance within the specification limits
Discharge times: 20 times for each discharge point, time interval 1 second. In the case of acceptance tests, the test program and the interpretation of the test results are subject to agreement between manufacturer and user. The test documentation shall include the test conditions and the test results.
Ambient temperature : 15C to 35C Relative humidity : 30% to 60%
11. QUALITY AND RELIABILITY

11.1 Quality Assurance

Unless otherwise specified in this specification or the applicable purchase order, the supplier shall be responsible for maintaining a statistical process program or performing inspections that are sufficient to assure that the parts supplied meet the requirements specified herein.

11.2 Reliability

The product shall have a designed MTBF of greater than 20,000 hours during its useful life.