Manuall Dupllex Priintiing from the Paper Cassette Manua Dup ex Pr nt ng from the Paper Cassette Manuall Dupllex Priintiing from the Manuall Feed Sllot Manua Dup ex Pr nt ng from the Manua Feed S ot Guiidelliines for Priintiing on Both Siides of the Paper Gu de nes for Pr nt ng on Both S des of the Paper 1-28 1-28 1-29 1-29 1-30 1-30
CHAPTER 2 PRINTER DRIVER AND SOFTWARE

Printer Driver

For Wiindows Users For W ndows Users
Features iin the PCL Priinter Driiver Features n the PCL Pr nter Dr ver Features iin the PS Priinter Driiver Features n the PS Pr nter Dr ver

2-2 2-2

2 ----8
For Maciintosh Users For Mac ntosh Users
For USB Users (HL-1440//1450//1470N Users Onlly) For USB Users (HL-1470N Users On y) For Network User (HL-1470N Users Onlly) For Network User (HL-1470N Users On y)

2-12 2-12

2-12 2-12 2-12 2-12

Software

Automatiic E-maiill Priintiing Automat c E-ma Pr nt ng Software for Networks Software for Networks
BRAdmiin Professiionall BRAdm n Profess ona Storage Manager Storage Manager Network Priinter Driiver Wiizard Network Pr nter Dr ver W zard Automatiic Emullatiion Sellectiion Automat c Emu at on Se ect on

2-13 2-13 2-14 2-14

2-14 2-14 2-14 2-14 2-15 2-15 2-15 2-15

CHAPTER 3 CONTROL PANEL

Serviice Callll IIndiicatiions Serv ce Ca nd cat ons 3-4 3-4

Control Panel Button

Priint Test Samplle Page Pr nt Test Samp e Page
Usiing Controll Panell Button Us ng Contro Pane Button Usiing the Priinter Driiver Us ng the Pr nter Dr ver

3-7 3-7

3 ----8
Priint Confiiguratiion and Fonts Pr nt Conf gurat on and Fonts

3-9 3-9

3 --9 3-10 3-10

CHAPTER 4 OPTIONS

IInstalllliing Addiitiionall Memory nsta ng Add t ona Memory

4-4 4-4

Lower Tray Unit Print Server (NC-2010p) IrDA Interface (IR-1000)
CHAPTER 5 ROUTINE MAINTENANCE

4-6 4-7 4-8

Toner Cartridge
Toner Low Message Toner Low Message Toner Empty Message Toner Empty Message Repllaciing the Toner Cartriidge Rep ac ng the Toner Cartr dge

Drum Unit

Change Drum Message Change Drum Message
Repllaciing the Drum Uniit Rep ac ng the Drum Un t

510 510

Cleaning

Periiodiic Maiintenance Parts Per od c Ma ntenance Parts

514 514

CHAPTER 6 TROUBLESHOOTING

Identifying Your Problem

Error Messages in the Status Monitor 6-2 Error Message Printouts Paper Handling Paper Jams and How to Clear Them Other Problems
For Maciintosh wiith USB For Mac ntosh w th USB

6-4 6-5 6-6 6-10

6-11 6-11
Improving the Print Quality How to Print Correctly

APPENDIX

6-12 6-18 A-1

Printer Specifications

Important Information for Choosing Your Paper A-6 Trademarks
Components When you unpack the printer, check to see that you have all of the following parts:
1. Printer 2. Drum unit assembly (with toner cartridge included) 3. Documents
4. CD-ROM 5. AC power cord
Components may differ from one country to another.
The power cord may differ slightly from this figure depending on the country where you purchased the printer.

Interface cable

An interface cable is not a standard accessory. Some computers have both a USB and a parallel port. Please purchase the appropriate cable for the interface you intend to use. Today most parallel cables support bi-directional communication, but some might have an incompatible pin assignment or may not be IEEE 1284-compliant. Do not use a parallel cable that is longer than 3 metres (10 feet).
(For HL-1440, HL-1450 and HL-1470N Users)
When you use a USB cable, be sure to use a high-speed twisted cable (12 Mbps) and connect it to the USB connector of your PC. Do not use the USB connector on the front of your PC or on the iMac keyboard.

General View

Front View
1. Tray extension flap 2. Face down output tray 3. Front cover 4. Paper cassette
5. Manual feed paper guides 6. Manual feed slot 7. Control panel

Rear View (HL-1230)

1. Rear cover 2. Power switch 3. AC power inlet 4. Parallel Interface connector

Rear View (HL-1440)

1. Rear cover 2. Power switch 3. AC power inlet 4. Parallel Interface connector 5. USB connector

Rear View (HL-1450)

1. Rear cover 2. Power switch 3. AC power inlet 4. Parallel Interface connector 5. USB Interface connector
6. Mini Din connector for lower tray unit

Rear View (HL-1470N)

10/100BASE TX LFA TEST
1. Rear cover 2. Power switch 3. AC power inlet 4. Parallel Interface connector 5. USB Interface connector 6. Mini Din connector for lower tray unit 7. 10/100Base TX port 8. LED 9. Test button
Please take note of the following before using the printer.

Power Supply

Use the printer within the specified power range. AC power: AC 220 240V or AC 110 120V Frequency: 50 Hz (220 V 240 V) or 50/60 Hz (110120 V) The power cord, including extensions, should not exceed 5 metres (16.5 feet). Do not share the same power circuit with other high-power appliances such as an air conditioner, copier, shredder and so on. If you cannot avoid using the printer with these appliances, we recommend that you use an isolation transformer or a highfrequency noise filter. Use a voltage regulator if the power source is not stable.

Recycled paper Transparencies Labels
3M CG 3300 Avery laser label #5160
Before you purchase large quantities of paper, please test print a small quantity to ensure that the paper is suitable. Use paper designed for plain paper copying. 2 Use paper that is 75 to 90 g/m. Use neutral paper; avoid acidic or alkaline paper. Use Long grain paper. Use paper with a moisture content of approximately 5%.
You can see the information to help you choose paper to use with this printer. See Important Information for Choosing Your Paper in the Appendix.

Printable Area

The figure below shows the printable area. Portrait
USA/Canada 0.17 inch (4.2 mm) 0.25 inch (6.35 mm) 0.17 inch (4.2 mm) 0.25 inch (6.35 mm)
Europe/other countries 4.2 mm 6.01 mm 4.2 mm 6.01 mm

Landscape

USA/Canada 0.17 inch (4.2 mm) 0.2 inch (5.08 mm) 0.17 inch (4.2 mm) 0.2 inch (5.08 mm) Europe/other countries 4.2 mm 5.0 mm 4.2 mm 5.0 mm
You can print on plain paper from the paper cassette or manual feed slot. Select the paper you use referring to What Kind of Paper can I Use? in this chapter.
Printing on Plain Paper from the Paper Cassette
Select the Paper Size, Media Type and paper Source etc. in the printer driver. Media Type: Plain Paper Paper Source: Tray1 PCL driver PS driver
Pull the paper cassette completely out of the printer.
Adjust the paper guides at the right and rear of the paper cassette to match the paper size you want to load. Make sure that the tips of the paper guides fit into the slots correctly.
Load paper into the paper cassette. Make sure the paper is flat in the cassette at all four corners.
Do not load more than 250 sheets of paper (80 g/m2) in the cassette, or paper jams may occur. Paper can be loaded up to the lines on the sliding guide.
When you print on the back of paper already printed on one side, load the side to be printed (blank side) face down in the cassette.
Install the paper cassette in the printer. Make sure it is inserted fully into the printer.
Extend the output tray extension flap to prevent printouts from sliding off the face down output tray.
If you choose not to extend the output tray extension flap, we recommend that you remove printed pages immediately after they exit the printer.
Send the print data to the printer.

Using Control Panel Button

Turn off the printer.

Make sure that the front cover is closed and the power cord is plugged in.
Hold down the control panel button as you turn on the power switch. All the LEDs will illuminate. Keep the button depressed until the Drum LED comes on. When the Drum LED comes on, release the button your finger.

Drum Read Alar y

Press the control panel button again. The printer will print a test sample page.

Using the Printer Driver

If you are using Brothers Windows PCL printer driver, use the Print Test Page button usually located in the General tab of the Windows printer driver.
Print Configuration and Fonts
You can print the current configuration and a list of the internal fonts using the control panel button or printer driver.
Hold down the control panel button as you turn on the power switch. All the LEDs will illuminate. Keep the button depressed until the Drum LED comes on. When the Drum LED comes on, release the button.

Drum Read y

m Alar Data
Press the control panel button again and hold it down until the Ready LED comes on.
When the Ready LED comes on, release the button. The printer prints the current configuration of the printer and a list of the internal fonts.

Drum y Read m Alar Data

This section is for HL-1440, HL-1450, HL-1470N users only.
If you are using Brothers Windows PCL printer driver, you can print the current configuration and a list of the internal fonts by clicking the Print Config and Print Font buttons in the Support tab.
This printer has the following optional accessories. You can increase the capabilities of the printer with these items. Click the check mark in the following table to see the detailed information for each item.
Model HL-1230 HL-1440 HL-1450 HL-1470N SIMM Lower Tray Unit Print Server IrDA Interface

standard

We recommend that you expand the printer memory to avoid any memory full errors.
For HL-1440 Users This printer has 2 Mbytes of standard memory and a slot for optional additional memory. The memory can be expanded up to a total of 34 Mbytes by installing a commercially available SIMM (single in-line memory module). For HL-1450 and HL-1470N Users These printers have 8 Mbytes of standard memory and a slot for optional additional memory. 4 Mbytes of memory is fitted on the board, the other 4 Mbytes is on the installed SIMM. The memory can be expanded up to a total of 36 Mbytes by installing a commercially available SIMM (single in-line memory module). When you want to expand the memory, you need to remove the fitted SIMM, and then install a new SIMM of at least 8 Mbytes.

Minimum Memory Recommendation (Including Resident Memory)
HL-1440 (Including 2 MB of internal memory)
300 dpi Letter/A4 Legal Standard Standard 600 dpi Standard Standard 1200 dpi 10 MB 10 MB
HL-1450 (Including 8 MB of internal memory)
HP LaserJet, EPSON FX-850 and IBM Proprinter XL emulation modes
300 dpi Letter/A4 Legal Standard Standard 600 dpi Standard Standard 1200 dpi 16 MB 16 MB
PostScript Level II language emulation mode
HL-1470N (Including 8 MB of internal memory)
This printer can accept memory SIMM with the following specifications:
Speed Pin type Height Output 60 nsec - 80 nsec 72 pin 25.4 mm (1.00) or less 32 bit or 36 bit
Additional memory is useful and may be necessary if you are using the Page Protection function. (For HL-1440 users) The resident memory of HL-1440 printer is 2 MB, you need to expand the printer memory by adding a SIMM to print at 1200 dpi. (For HL-1470N users) You have to expand the printer memory by adding a SIMM to use the FTP/IPP protocol.
The printer has only one slot for a SIMM upgrade. If you want to increase your printer memory again after you have already installed a SIMM module in the slot, you will need to remove the previously installed SIMM.
Installing Additional Memory
Turn off the printer and unplug the power cord from the AC outlet. Disconnect the interface cable from the printer.
Be sure to turn off the printer before you install or remove SIMM.
Open the rear cover. Unscrew the two screws that secure the access cover and remove it.
Unpack the SIMM and hold it by the edges.
SIMM boards can be damaged by even a small amount of static electricity. Do not touch the memory chips or the board surface. Wear an antistatic wrist strap when you install or remove the board. If you do not have an antistatic wrist strap, frequently touch the bare metal on the printer.
Install the SIMM into the slot at an angle, and then push it gently toward the vertical until it clicks into place.

5. 6. 7.

Re-install the access cover and secure the access cover with the two screws.
Reconnect the interface cable (printer cable) to your computer. Plug the power cord into the AC outlet, and then turn on the power switch.
To check that you installed the SIMM correctly, print the configuration sheet by using the selection in the driver and check it to make sure it shows the additional memory. See Print Configuration and Fonts in Chapter 3.

Lower Tray Unit

The lower tray unit is a device that functions as an additional paper source. It can hold a maximum of 250 sheets of paper (80 g/m2 or 21 lb.).
To purchase the optional lower tray unit, please consult the dealer where you purchased the printer. For installation details, see the instructions supplied with the lower tray unit.

Print Server (NC-2010p)

Toner Low Message

If the LED shows this message, the toner will soon run out. Purchase a new toner cartridge and have it ready before you get a Toner Empty message.
Both Alarm and Data (Toner) LEDs will blink continuously to indicate that the toner cartridge is nearly empty. This blinking will not stop until you have installed a new toner cartridge.

Toner Empty Message

If the LED shows the following message, the printer has run out of toner or the toner is not evenly distributed inside the cartridge.
Replacing the Toner Cartridge
To ensure optimum print quality, be sure to use quality toner cartridges. To purchase toner cartridges, consult the dealer where you purchased the printer.

Open the front cover.

Pull out the drum unit assembly.
We recommend that you place the drum unit assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, do not touch the electrodes shown in the illustration.
Press the lock lever down, and then pull the toner cartridge out of the drum unit assembly.
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, immediately wipe or wash it off with cold water.
Be sure to seal the toner cartridge tightly so that toner powder does not spill out of the cartridge. Dispose of the used toner cartridge in accordance with local plastic waste regulations.
Unpack the new toner cartridge. Keeping the cartridge horizontal, gently rock it from side to side five or six times.
Wait to unpack the toner cartridge until immediately before you install it in the printer. If toner cartridges are left unpacked for a long period of time the toner life will be shortened. If an unpacked drum unit is subjected to excessive direct sunlight or room light, the unit may be damaged. Use a genuine Brother toner cartridge that is specially formulated to ensure optimum print quality. Printing with a 3rd party toner or 3rd party toner cartridge may reduce not only the print quality but also the quality and life of the printer itself. It may also cause serious damage to the performance and life of a drum unit. Warranty coverage does not apply to problems caused by the use of 3rd party toner or 3rd party toner cartridges.
Remove the protective cover.
Install the toner cartridge immediately after you remove the protective cover. Do not touch the shaded parts in the illustration to prevent any degradation to the print quality.

While pressing the lock lever, pull the toner cartridge out of the drum unit assembly.
Discard the used drum unit according to local regulations. Be sure to seal up the drum unit tightly so that toner powder does not spill out of the unit.
Unpack the new drum unit.
Wait to unpack a drum unit until immediately before you install it in the printer. If an unpacked drum unit is subjected to excessive direct sunlight or room light, the unit may be damaged.
Install the toner cartridge into the new drum unit until you hear it lock into place with a click. When the toner cartridge is installed correctly, the lock lever is lifted automatically.
Make sure you install the toner cartridge correctly, or it may separate from the drum unit.
Re-install the drum unit assembly in the printer. Make sure that the printer is turned on, the front cover is open and the Drum and Alarm LEDs are illuminated.
Reset the drum counter referring to the instructions supplied with the new drum unit.
The Drum LED indication does not disappear until you reset the drum counter. Do not reset the drum counter when you replace only the toner cartridge.

Close the front cover.

Make sure that the Drum LED is now off.
Clean the printer exterior and interior routinely. If printouts are stained with toner, clean the printer interior and drum unit. See the Maintenance Tutorial section in the supplied CD-ROM. You can see the instructional movie.
1. You can see how to clean the scanner window. 2. You can see how to clean the corona wire in the drum unit.
Periodic Maintenance Parts
You need to replace the maintenance parts periodically to maintain print quality. The units listed below should be replaced after printing the following number of pages.
Item Fixing unit Separator pad holder assy Pick up roller assy Approximate Life 50,000 pages * 50,000 pages * 50,000 pages * To Purchase Replacement Call Customer Support Call Customer Support Call Customer Support
* The actual number of printed pages may vary depending on your average type of print job and paper. The figures quoted are based upon 5% coverage per page.
First, check the following:
The power plug is connected correctly and the printer is turned on. All of the protective parts have been removed. The toner cartridge and drum unit are installed correctly. The front cover is fully closed. Paper is inserted correctly into the paper cassette. The interface cable is securely connected between the printer and computer. The correct driver for the printer is installed and selected. The PC is set up to connect to the correct printer port.

PRINT OVERRUN

RESOLUTION ADAPTED (The printer has printed the document at a reduced resolution) (For HL-1440, HL-1450 and HL-1470N Users) Expand the printer memory by adding a commercially available SIMM. See Installing Additional Memory in Chapter 4.

Paper Handling

First, ensure that you are using paper that meets Brother recommended paper specifications. See What Kind of Paper can I Use? in Chapter 1.
Problem The printer does not load paper. Recommendation If there is paper in the paper cassette, make sure it is straight. If the paper is curled, you should straighten it before printing. Sometimes it is helpful to remove the paper, turn the stack over and put it back in the paper cassette. Reduce the amount of paper in the paper cassette, and then try again. Check that manual feed mode is not selected in the printer driver. Re-insert the paper firmly, one sheet at a time. Make sure that manual feed mode is selected in the printer driver. The printer can load envelopes from the manual feed slot. Your application software must be set up correctly to print on the envelope size you are using. This is usually done in the page setup or document setup menu of your software. Refer to your software application manual. Clear the jammed paper referring to Paper Jams and How to Clear Them or the paper jam instructional video on the CD-ROM. Close the rear cover. Make sure that the cable is connected to the printer Make sure that the appropriate printer driver is selected.
The printer does not load paper from the manual feed slot. The printer will not load envelopes.
A paper jam has occurred. The printer does not print into the output tray. The printer does not print on the specified paper. (For HL-1450 with optional lower tray unit user only)
Paper Jams and How to Clear Them
When a paper jam occurs, the printer indicates it by lighting the control panel LEDs as shown below.
After you have just used the printer, some internal parts of the printer are extremely HOT! When you open the front or rear cover of the printer, never touch the shaded parts shown in the following diagram.
Clear the jammed paper referring to the following description. If the jammed paper is removed completely by using the information in the following steps, you can install the paper cassette first, and then close the front cover and the printer will resume printing automatically. If the printer does not resume printing automatically, press the control panel button. If the printer still does not resume printing, please check that all the remaining jammed paper has been removed from the printer. Then try printing again.
If a paper jam occurs when using the lower tray unit, check for correct installation of the upper paper cassette. Always remove all paper from the paper cassette and straighten the stack when new paper is added. This helps prevent multiple sheets of paper from feeding through the printer at one time and reduces paper jams.

ABCDEFGH CDEF abcdefghijk defg

ABCD abcde 01234

ABCDEFGH abcdefghijk

Gray background

Image Defect Samples

Toner specks

Recommendation Make sure that you use paper that meets the specifications. A rough surfaced paper may cause the problem. See What Kind of Paper can I Use? in Chapter 1. The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5.
Make sure that you use paper that meets the specifications. See What Kind of Paper can I Use? in Chapter 1. Select the Thick paper mode in the printer driver, or use thinner paper than you are currently using. Check the printers environment because conditions such as high humidity may cause this situation to occur.

Hollow print

Clean the primary corona wire of the drum unit. See "Cleaning" in Chapter 5. The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5.

All black

Recommendation If the problem is not solved after printing a few pages, the drum unit may have glue from label stock on the OPC drum surface. Clean the drum unit as follows: 1. Position the print sample in front of the drum unit, and find the exact position of the image defect.
94 mm 3.7 in. 94 mm 3.7 in.
White Spots Printed pages have white spots in black text and graphics at intervals of 94 mm (3.7 in.).
2. Turn the drum unit gear by hand while looking at the surface of the OPC drum.
Black Spots Printed pages have black spots at intervals of 94 mm (3.7 in.).
3. When you have located the mark on the drum that matches the print sample, wipe the surface of the OPC drum with a cotton swab until the dust or paper powder on the surface comes off.

Recommendation

Do not try to clean the surface of the photosensitive drum with a sharp object, such as a ball-point pen, etc.
The drum unit may be damaged. Install a new drum unit. See Replacing the Drum Unit in Chapter 5.
Printed pages have black spots at intervals of 94 mm (3.7 in.).
Recommendation The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5. Make sure that you use paper that meets specifications. See What Kind of Paper can I Use? in Chapter 1.
Black Horizontal repetitive defects Toner scatters and stains the printed page.

If you use label sheets for laser printers, the glue from the sheets may sometimes stick to the OPC drum surface. Clean the drum unit. See Improving the Print Quality in this chapter. Do not use paper that has clips or staples because they will scratch the surface of the drum. If the unpacked drum unit is subject to excessive direct sunlight or room light, the unit may be damaged. Make sure that you use paper that meets the specifications. A rough surfaced paper or thick media can cause the problem. Make sure that you select the appropriate media type in the printer driver. The problem may disappear by itself. Try printing multiple pages to clear this problem, especially if the printer has not been used for a long time. The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5. Clean the printer interior and the primary corona wire in the drum unit. See "Cleaning" in Chapter 5. The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5.

White horizontal stripes

Horizontal Lines
Black Vertical lines Printed pages are stained with toner or have vertical stripes.
Clean the primary corona wire of the drum unit. See "Cleaning" in Chapter 5. Make sure the primary corona wire cleaner is at the Home position (L). The drum unit may be damaged. Install a new drum unit. See "Replacing the Drum Unit" in Chapter 5. The toner cartridge may be damaged. Install a new toner cartridge. See "Replacing the Toner Cartridge" in Chapter 5. Make sure that a torn piece of paper is not inside the printer covering the scanner window. The fixing unit may be smudged. Call Customer Support.
Recommendation You may clear the problem by wiping the scanner window with a soft cloth. See Cleaning in Chapter 5. The toner cartridge may be damaged. Install a new toner cartridge. See "Replacing the Toner Cartridge" in Chapter 5.

White Vertical streaks

FGH ABCDE fghijk abcde

Page skew

Curl or wave
Make sure the paper or other media is loaded into the paper cassette correctly and that the guides are not too tight or too loose against the paper stack. Set the paper guides correctly. Make sure that the tips of the paper guides fit into the slot correctly. See Printing on Plain Paper from the Paper Cassette in Chapter 1. If you are using the manual feed slot, see "Printing on Plain Paper from the Manual Feed Slot" in Chapter 1. The paper cassette may be too full. See " Printing on Plain Paper from the Paper Cassette " in Chapter 1. Check the paper type and quality. See "What Kind of Paper can I Use?" in Chapter 1. Check the paper type and quality. Both high temperature and humidity will cause paper to curl. See What Kind of Paper can I Use? in Chapter 1. If you use the printer infrequently, the paper may have sat for too long in the paper cassette. Turn over the stack of paper in the paper cassette. Also, try rotating the paper 180 in the paper cassette. Try printing using the straight-through output path. See " Printing on Plain Paper from the Manual Feed Slot" in Chapter 1. Make sure that paper is loaded properly. See " Printing on Plain Paper from the Paper Cassette " in Chapter 1. Check the paper type and quality. See What Kind of Paper can I Use? in Chapter 1. Try printing using the straight-through output path. See " Printing on Plain Paper from the Manual Feed Slot " in Chapter 1. Turn over the stack of paper in the tray or try rotating the paper 180 in the input tray.

B DEFGH abc efghijk

A CD bcde 1 34

Wrinkles or creases

How to Print Correctly
Problem The printer prints unexpectedly or it prints garbage. Recommendation Make sure the printer cable is not too long. We recommend you use a parallel cable of less than 2 metres (6 1/2 feet) in length. Check if the printer cable is damaged or broken. If you are using an interface-switching device, remove it and connect your computer directly to your printer and try again. Check that the appropriate printer driver is selected as Set as Default. Check that the printer is not connected to the same port that is also connected to a mass storage device or scanner. Remove all other devices and connect the port to the printer only. Turn off printer status reporting in the device options tab in the printer driver. Press the control panel button to print the data remaining in the printer. If this does not clear the error, reduce the complexity of your document or reduce the print resolution. (HL-1440, HL-1450 and HL-1470N only) Expand the printer memory by adding a commercially available SIMM. See Installing Additional Memory in Chapter 4. Set page protection to ON by using the supplied Windows driver or RPC program. Change the following settings in the supplied Windows driver, and then try again. The best combination of settings below will vary depending on your document. Graphics Mode TM True Type mode TM Use Printer True Type Fonts Press the control panel button to print the data remaining in the printer. Reduce the print resolution or reduce the complexity of your document. (HL-1440, HL-1450 and HL-1470N only) Expand the printer memory by adding a commercially available SIMM. See Installing Additional Memory in Chapter 4. Most laser printers have a restricted area that cannot be printed on. Usually the first two lines and the last two lines of a page cannot have print (leaving 62 printable lines). Adjust the top and bottom margins in your document to allow for this.
The printer cannot print full pages of a document. An error message PRINT OVERRUN occurs.
The printer cannot print full pages of a document. A "MEMORY FULL" error message occurs.
My headers or footers appear when I view my document on screen but do not show up when I print it.

Utilities

Automatic E-mail *8 Printing Interactive Help Status Monitor
Driver Deproyment *10 Wizard

Control Panel

MODEL LED Switch *7 *8 *9 *10

4 LEDs 1 Key

AppleTalk only Utility software that automatically prints specified e-mail messages at a pres cheduled time. (For Windows 95 / 98 / Me) Instructional animations for problem solving The Network Printer Driver Wizard automates the installation of a printer in a peer-to-peer network.

Paper Handling

MODEL *11 Paper Input
Paper Cassette (Standard) Manual Feed Paper Cassette (Option) Face Down Face Up 250 Sheets

1 Sheet N/A 250 Sheets

Paper Output

150 Sheets 1 Sheet

Media Specifications

MODEL Media Types

Manual Feed Paper Cassette (Standard) Paper Cassette (Option) Manual Feed Paper Cassette Manual Feed Paper Cassette (Standard) Paper Cassette (Option)
Plain Paper, Bond Paper, Recycled Paper, Envelopes, Labels, and Transparencies Plain Paper, Bond Paper, Recycled Paper, Transparencies
Plain Paper, Bond Paper, Recycled Paper

Media Weights

16 - 43 lb (60 - 161 g/m ) 16 - 28 lb (60 - 105 g/m ) Custom : 2.75" x 4.57" - 8.5" x 14" (69.8 x 116 - 216 x 356 mm) A4, Letter, B5(ISO), A5, B6(ISO), A6, Executive, Legal (US & Canada only)

Media Sizes

A4, Letter, B5(ISO), A5, Executive, Legal (US & Canada only)

*11 *12

Calculated with 80g/m2 paper Up to 10 sheets

Printer Driver Functions

MODEL Page Layout
N in 1 Printing Poster Printing Watermark Printing 2, 4, 9, 16, 25 in 1 page 1 in 4, 9, 16, 25 Yes Quick Print Setup Manual Duplex

Supplies

MODEL Toner
Standard Cartridge High Yield Cartridge
3,000 pages A4/LTR pages @5% coverage 6,000 pages A4/LTR pages @5% coverage 20,000 A4/LTR pages (1 page / job)

Dimensions / Weights

MODEL Dimensions Weights