Important Safety Instructions
Before using this printer, read and follow these safety instructions: Use only the power cord that comes with the printer. Use of another cord may cause fire or shock. Do not use the cord with any another equipment. Make sure the power cord meets all relevant local safety standards. Use only the type of power source indicated on the label. Place the printer near a wall outlet where the power cord can be easily unplugged. Do not let the power cord become damaged or frayed. Make sure the total ampere rating of the devices plugged into an extension cord or a wall outlet does not exceed the ampere rating limit. Avoid locations that are subject to rapid changes in heat or humidity, shocks or vibrations, dust, or direct sunlight. Do not block or cover openings in the case or insert objects through the slots. Place the printer on a flat, stable surface that extends beyond its base in all directions. It will not operate properly if it is tilted or at an angle. And make sure the back of the printer is at least 10 cm away from the wall for sufficient ventilation. Do not open the scanner unit while copying, printing, or scanning. Do not touch the white flat cable inside the printer. Do not spill liquid on the printer. Do not use aerosol products that contain flammable gases inside or around the printer. Doing so may cause fire. Except as specifically explained in your documentation, do not attempt to service the printer yourself.
Unplug the printer and refer servicing to
qualified service personnel under the following conditions: if the power cord or plug is damaged; if liquid has entered the printer; if the printer has been dropped or the case damaged; if the printer does not operate normally or exhibits a distinct change in performance. When storing or transporting the printer, do not tilt it, stand it on its side, or turn it upside down; otherwise ink may leak from the cartridge. Be careful not to trap your fingers when closing the scanner unit. Do not press too hard on the document table when placing the originals.
Ink cartridge safety instructions
Keep ink cartridges out of the reach of
children and do not drink the ink. If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water. If you still have discomfort or vision problems, see a doctor immediately. If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust and store it in the same environment as the printer. Do not touch the ink supply port or surrounding area.

Control Panel

Buttons
Buttons a Mode * Function Switches the modes between r Copy, C Memory Card, and J Photo. Sets the number of copies, or changes the cropping area. Displays detailed settings for each mode. Selects photos and menu items. Activates the settings you have selected. Cancels the current operation and returns to the previous menu. Runs maintenance programs or adjusts miscellaneous settings. Changes the view of photos on the LCD screen, or crops the photos. Starts copying and printing. Turns the printer on and off. (Light is on when the printer is on, and flashes when the printer is active, turning on, or turning off.) Stops copying and printing, or resets the settings you have made.

Copies (+ and -)

x Menu * udlr 4-way Scroll OK

y Back

f F [Setup] *
G [Display/Crop] x Start P On
Control panel design varies depending by location.
y Stop/Clear [y Stop/Clear Settings]
* For details on the items in each mode, see Summary of Panel Settings on page 24.

LCD screen

The LCD screen may contain a few small bright or dark spots, and because of its features it may have an uneven brightness. These are normal and do not indicate that it is damaged in any way.
Press r to open the setting item list. Press u or d to select the setting item and then press OK. Press l or r to change the displayed photo on the LCD screen.

Using the LCD screen

Follow the instructions below to select and change the setting menus and the photos on the LCD screen.
Adjusting the angle of the LCD screen
You can change the angle of the LCD screen.
Adjusting the brightness of the LCD screen
You can adjust the brightness of the LCD screen. 1. Press F [Setup] to enter the setup mode. 2. Press l or r to select Maintenance, then press OK. 3. Press u or d to select LCD Brightness, then press OK. You see the following screen.

b,d,e c d

4. Press u or d to adjust the brightness of the screen, then press OK.

Power saving function

After 13 minutes of inactivity, the screen turns black to save energy. Press any button (except P On) to return the screen to its previous state.
Use Copies + or - to set the number of copies for the selected photo. Press l or r to select the setting item. Press u or d to select the menu item. The highlighted part moves up or down.

Selecting Paper

Before printing, you need to select the correct paper type setting. This important setting determines how the ink is applied to the paper. Note:
The availability of special media varies by location. You can find the part number for the following Epson special papers on the Epson support Web site.

2. Select a copy settings.
2. Press G [Display/Crop]. You see the cropping screen.
Select Color for color copies or B&W for black-and-white copies. Select a layout option. Set the number of copies.
3. Use the following button to set the area you want to crop.
Copies +, u, d, l, r Change the frame size. Move the frame.
3. Press x Menu to change the settings (& Print settings for Copy mode on page 24). Then press OK. 4. Press x Start. Note:
4. Press OK to confirm the cropped image. Note:
To readjust the frames position, press y Back to return to the previous screen.
Place your photo 5 mm away from the edge of the document table. Also when you place two photos, position each photo at least 5 mm away from the adjacent photo. You can copy several different sized photos at the same time, as long as they are larger than mm and all fit inside the mm area.
5. When you have finished checking the cropped image, press OK. Note:
The image. icon is displayed on the cropped

Handling a Memory Card

Inserting a memory card
If a digital camera is connected to the printer, disconnect it before you insert your memory card.
1. Make sure no memory cards are in the slots. Then insert your memory card. c Caution:
Do not insert more than one memory card at a time. Do not try to force the memory card into the slot. Memory cards will not go all the way in. Make sure you check which direction the card should be inserted, and if the card needs an adapter, make sure you attach the adapter before inserting the card. Otherwise, you may not be able to remove the card from the printer.
xD-Picture Card xD-Picture Card Type M xD-Picture Card Type H
SD Memory Card SDHC Memory Card MultiMediaCard

Compact Flash Microdrive

miniSD card* miniSDHC card*
microSD card* microSDHC card* (* Adapter required)

Removing the memory card

1. Make sure the memory card light is not flashing. 2. Remove the memory card by pulling it straight out.

Printing Photos

1. Press C Memory Card.
Memory Stick Memory Stick PRO MagicGate Memory Stick
2. Select one of the settings in the following table for viewing/printing your photos, and then press OK. Follow the instructions below to select the photos and set the number of copies.
Setting View and Print Photos Print All Photos Print by Date
Instructions Select a photo and set the number of copies. Press OK. Set the number of copies. You can view all of the photos by using l or r. Select the date, and then place a check mark and press OK. Press OK again, and select a photo. Set the number of copies. See Selecting and Printing Photos Using an Index Sheet on page 12. Your printer displays the photos on the memory card in sequence. When you see the photo that you want to print, press OK and set the number of copies. If you want to print additional photos, select the photo you want to print. Then set the number of copies.

Memory Stick Micro* Memory Stick Duo* Memory Stick PRO Duo* MagicGate Memory Stick Duo* (* Adapter required)
Print Index Sheet Slide Show
2. Make sure the memory card light flashes and then stays on.

Memory card light

3. Press x Menu and change the settings (& Print settings for Memory Card mode on page 25). Then press OK. 4. Press x Start. Note:
This printer retains your settings even after it has been turned off.

Printing an index sheet

1. Press C Memory Card. 2. Select the photo you want to crop with the View and Print Photos option (& Printing Photos on page 11). 3. Press G [Display/Crop]. 4. Refer to Cropping and enlarging a photo on page 9 and follow steps 4 to 7. 5. Press x Menu and change the settings (& Print settings for Memory Card mode on page 25). Then press OK. 6. Press x Start.
Selecting photos from the index sheet

Scanning the index sheet

Printing with DPOF settings
If your camera supports DPOF, you can use it to preselect photos and the number of copies to print while the memory card is still in your camera. See your cameras instruction manual for details. 1. Insert a memory card containing DPOF data (& page 10). 2. Press OK. 3. Press x Menu and change the settings (& Print settings for Memory Card mode on page 25). Then press OK. 4. Press x Start.
Selecting and Printing Photos Using an Index Sheet
You can use an index sheet to select the photos you want to print.
Printing the selected photos
1. Printing an index sheet
1. Load several sheets of A4-size plain paper (& page 6). 2. Press C Memory Card.

Good: NOT good:

3. Select Print Index Sheet, then press OK.
1. In section 1, select the paper size. Fill in the oval to the left of your selection. 2. Select whether to print your photos with or without borders. 3. Fill in the oval to include an optional data stamp. 4. In section 2, select All to print one copy of each photo, or fill in the number beneath each photo to select 1, 2, or 3 copies.

4. Select Print Index Sheet Select. 5. Select the range of photos. Then press OK.
Range Select All Photos Description Prints all the photos stored on a memory card. Prints 30/60/90 photos from the latest one in order of the file name.
3. Scanning the index sheet and printing the selected photos
1. Place the index sheet face-down on the document table, so that the top of the sheet is aligned with the left edge of the document table.
Latest 30 Latest 60 Latest 90

6. Press x Start. Note:

Make sure the triangle mark on the upper left corner of the index sheet is printed properly. If the index sheet is not printed correctly, the printer cannot scan it.
2. Selecting photos from the index sheet
On the index sheet, use a dark pen or pencil to fill in the ovals and make your selections.
2. Close the document cover. 3. Load the size of photo paper you marked on the index sheet (& page 6). 4. On the LCD screen, make sure Print Photos from Index Sheet is selected, then press x Start. Note:
If you have more than one index sheet, wait each time until printing is complete. Then repeat the steps above to scan and print from each additional sheet.
Using the PictBridge or USB DIRECT-PRINT
PictBridge and USB DIRECT-PRINT let you print your photos by connecting your digital camera directly to the printer. Make sure your camera and photos meet the following requirements.
Direct printing compatibility File format Image size PictBridge or USB DIRECT-PRINT USB port JPEG pixels to pixels
6. Connect the USB cable from your camera to the USB port on the front of the printer.
1. Make sure your printer is not printing from a computer. 2. Remove any memory cards from the printer. 3. Press F [Setup]. 4. Select PictBridge Setup, then press OK. 5. Select the print settings (& Print settings for Memory Card mode on page 25). Then press OK.
7. Make sure your camera is turned on and use it to select the photos, adjust any necessary settings, and print your photos. See your cameras manual for details. Note:
Depending on the settings on this printer and the digital camera, some combinations of paper type, size, and layout may not be supported. Some of the settings on your digital camera may not be reflected in the output.

Precautions

w Warning:
If ink gets on your hands, wash them thoroughly with soap and water. If ink gets in your eyes, flush them immediately with water. If you still have discomfort or vision problems, see a doctor immediately.

Never move the print head by hand. When an ink cartridge is expended, you cannot continue printing even if the other cartridges still contain ink. Leave the expended cartridge installed until you have obtained a replacement. Otherwise the ink remaining in the print head nozzles may dry out.
1. Do one of the following: If an ink cartridge is expended: Look at the message on the LCD screen to find out which cartridge should be replaced, then press OK. If an ink cartridge is not expended: Press F [Setup]. Select Maintenance, and press OK. Select Change Ink Cartridge, and press OK. 2. Lift up the scanner unit.
Some ink is consumed each time cartridges are inserted because the printer automatically checks their reliability. For maximum ink efficiency, only remove an ink cartridge when you are ready to replace it. Ink cartridges with low ink status may not be used when reinserted. Epson recommends the use of genuine Epson ink cartridges. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior. Epson cannot guarantee the quality or reliability of non-genuine ink. Information about the ink cartridge status is not displayed when non-genuine ink is used.

c Caution:

Do not lift up the scanner unit when the document cover is open.
3. Open the cartridge cover.
Removing and Installing Ink Cartridges
Make sure you have a new ink cartridge before you begin. Once you start replacing a cartridge, you must complete all the steps in one session. Note:
Do not open the ink cartridge package until you are ready to install it in the printer. The cartridge is vacuum packed to maintain its reliability.
Never attempt to open the cartridge cover while the print head is moving. Wait until the print head has stopped at the replacement position.
4. Squeeze the tab and lift it straight up.
You must remove the yellow tape from the cartridge before installing it; otherwise, print quality may decline or you may not be able to print. Do not remove the seal.
Do not refill the ink cartridge. Other products not manufactured by Epson may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior.
Be sure to always install an ink cartridge into the printer immediately following the removal of the current ink cartridge. If the ink cartridge is not installed promptly, the print head may dry out, rendering it unable to print.

If it is difficult to remove the cartridge, lift the cartridge with more force until comes out.
7. Place the new ink cartridge in the cartridge holder and press it down until it clicks into place.
5. Before you open the new ink cartridge package, shake it four or five times. Then remove it from the package.
8. Close the ink cartridge cover and press it until it clicks into place. c Caution: c Caution:
Be careful not to break the hooks on the side of the ink cartridge when you remove it from the package. Do not touch the green chip on the side of the cartridge. This can damage the ink cartridge. If you find it difficult to close the cover, make sure all the cartridges are firmly seated. Press down on each cartridge until you hear it click into place. Do not attempt to force the cover closed.
6. Remove the yellow tape.
9. Close the scanner unit.
10. Press OK. The ink delivery system starts charging. c Caution:
Do not turn off the printer during ink charging as this will waste ink.
If a message on the LCD screen still tells you that a cartridge should be replaced, the ink cartridges may not be installed properly. Press OK again, and press down the ink cartridge until it clicks into place.
Checking the Ink Cartridge Status
You can check which cartridge is low. 1. Press F [Setup]. 2. Select Ink Levels, then press OK. You see a graphic showing the ink cartridge status:
C (Cyan), M (Magenta), Y (Yellow), B (Black)
2. Press F [Setup]. (If you have just finished cleaning the print head, you can start the nozzle check by pressing x Start.) 3. Select Maintenance, then press OK. 4. Select Nozzle Check, then press OK. 5. Press x Start. 6. Examine the nozzle check pattern you printed.
If your printout looks like the one shown below, the print head does not need to be cleaned yet. Press OK to return to the main menu.
When your ink starts getting low, is displayed. 3. Press y Back to return to the previous screen. Note:
Epson cannot guarantee the quality or reliability of non-genuine ink. If non-genuine ink cartridges are installed, the ink cartridge status may not be displayed.
If your printout has gaps like the one shown below, clean the print head as described in the next section.

Cleaning the print head

Follow these steps to clean the print head so it can deliver ink properly. Before cleaning the print head, run a nozzle check to see if the print head needs cleaning (& Checking the print head on page 18). Note:
Print head cleaning uses ink, so clean it only if quality declines. When ink is low, you may not be able to clean the print head. When ink is expended, you cannot clean the print head. Replace the appropriate ink cartridge first (& Removing and Installing Ink Cartridges on page 15).
Checking and Cleaning the Print Head

If your printouts are unexpectedly light, colors are missing, or you see light or dark lines across the page, you may need to clean the print head. Tip:
To maintain print quality, we recommend printing a few pages on a regular basis.

Checking the print head

You can print a nozzle check pattern to see if any print head nozzles are clogged, or to check the results after cleaning the print head. 1. Load A4-size plain paper (& page 6).
1. Press F [Setup]. 2. Select Maintenance, then press OK. 3. Select Head Cleaning, then press OK.
Never turn off the printer while head cleaning is in progress. You may damage it.
5. When cleaning finishes, a message is displayed on the LCD screen. Press x Start to print a nozzle check pattern to check the results (& Checking the print head on page 18). If there are still gaps or the test patterns are faint, run another cleaning cycle and check the nozzles again. Note:
If you do not see any improvement after cleaning about four times, turn off the printer and wait for at least six hours. This lets any dried ink soften. Then try cleaning the print head again. If quality still does not improve, one of the ink cartridges may be old or damaged and needs to be replaced (& Removing and Installing Ink Cartridges on page 15).

Aligning the Print Head

If your printouts contain misaligned vertical lines or horizontal banding, you may be able to solve this problem by aligning the print head. 1. Load A4-size plain paper (& page 6). 2. Press F [Setup]. 3. Select Maintenance, then press OK. 4. Select Head Alignment, then press OK. 5. Press x Start. Four rows of alignment patterns are printed. 6. Look at pattern #1 and find the patch that is most evenly printed, with no noticeable streaks or lines. 7. Select the number for that patch, then press OK.
4. Press x Start. The printer begins cleaning the print head. Follow the message on the LCD screen.
8. Enter the numbers for the other patterns in the same way. 9. When you finish, press OK and you see a message indicating alignment is complete.

See your online Users Guide for help on using the printer with a computer.

Problems and Solutions

Setup problems
LCD screen came on and then went out. The printers voltage may not match the outlet rating. Turn off the printer and unplug it immediately. Then, check the printer labels. c Caution
If the voltage does not match, DO NOT PLUG YOUR PRINTER BACK IN. Contact your dealer.

Error Messages

Error Messages A printer error has occurred. Turn off the printer, then press On button to turn on. See your documentation. A scanner error has occurred. See your documentation. Waste ink pad in the printer is saturated. Contact your dealer to replace it. Cannot recognize ink cartridges. Make sure the ink cartridges are installed correctly. Solution Turn the printer off and then back on. Make sure that no paper is still in the printer. If the error message still appears, contact your dealer. Turn the printer off and then back on. If the error message still appears, contact your dealer. Contact your dealer to replace it.
The printer makes noise after you turn it on. Make sure the protective tape is not blocking the print head. After releasing the print head turn off the power, wait a moment, then turn it back on. The printer makes noise after ink cartridge installation. When you install ink cartridges, the ink delivery system must be charged. Wait until charging is finished (the charging message disappears from the LCD screen), then turn off the printer. If you turn it off too soon, it may use extra ink the next time you turn it on. Make sure the ink cartridges are seated securely and no packing material remains in the printer. Open the cartridge cover and push the cartridges down until they click into place. Turn off the power, wait a moment, then turn it back on. A screen that prompts you to restart the computer did not appear after finishing the software installation.
Make sure the ink cartridges are installed correctly. (& Removing and Installing Ink Cartridges on page 15). Then try again. Make sure the memory card has been inserted correctly. If so, check to see if there is a problem with the card and try again.

To clean the inside of the printer, make a copy without placing a document on the document table. Load and eject dry paper several times. See your online User's Guide.
Use only paper recommended by Epson and genuine Epson cartridges. Clean the document table. See your online User's Guide. Your printout is faint or has gaps. Clean the print head (& Cleaning the print head on page 18). If you notice jagged vertical lines, you may need to align the print head (& Aligning the Print Head on page 19). The ink cartridges may be old or low on ink. Replace an ink cartridge (& Removing and Installing Ink Cartridges on page 15).

Scan quality problems

Only part of the photo is scanned.
The printer has non-readable areas at the edges. Move the photo away from the edges slightly. The file size is too big. Try changing the quality settings.

For more solutions

If you cannot solve the problem using the troubleshooting, contact customer support services for assistance. You can find customer support information for your area in your online User's Guide or warranty card. If it is not listed there, contact the dealer where you purchased your printer.

Copy Mode

Menu Copies Color/B&W Layout
Setting Item 1 to 99 Color, B & W With Border Borderless
Description Copies your original with a standard 3-mm margin. Copies your photo all the way to the edges of the paper.
Your image is slightly enlarged and cropped to fill the sheet of paper. Print quality may decline in the top and bottom areas of the printout, or the area may be smeared when printing.
Print settings for Copy mode

Menu Zoom

Setting Item Actual, Auto Fit Page
Description Select Actual to print your photo at its original size. Select Auto Fit Page for borderless printing and resizing the image to fit various common paper sizes. You can also resize the original to a specific scale using Copies + or -. -

Paper Type

Plain Paper, Matte, Prem. Glossy, Ultra Glossy, Photo Paper 10 x 15 cm, 13 x 18 cm, A4

Paper Size

Menu Quality Density Expansion
Setting Item Draft, Standard, Best -4 to +4 Standard, Mid., Min.

Description -

Select the amount the image is expanded when you select Borderless. Standard: The image is slightly enlarged and cropped to fill the sheet of paper. Mid.: Margins might be printed. (Low expansion rate.) Min.: Margins might be printed. (Lowest expansion rate.)

Memory Card Mode

Setting Item View and Print Photos Print All Photos Print by Date Print Index Sheet Slide Show
Description Prints only the photos that you choose. Prints all the photos on your memory card. Prints photos by the date they ware taken. Prints thumbnails of the photos on your memory card and lets you select which ones you want to print. Displays all photos on your memory card as a slide show and prints photos that you choose.
Print settings for Memory Card mode

Menu Paper Type

Setting Item Prem. Glossy, Ultra Glossy, Photo Paper, Plain Paper, Matte

Menu Paper Size Layout

Setting Item 10 x 15 cm, 13 x 18 cm, 16:9 wide, A4 Borderless
Description Prints your photo all the way to the edges of the paper.
Your image is slightly enlarged and cropped to fill the sheet of paper. Print quality may decline in the top and bottom areas of the printout, or the area may be smeared when printing. With Border Quality Date Standard, Best None, yyyy.mm.dd, mmm.dd.yyyy, dd.mmm.yyyy On, Off Prints your photo with a white margin at the edge. Prints the date your photo was taken.

Bidirectional

Select On to increase the print speed. Select Off to improve the print quality (but your photos print more slowly). Select the amount the image is expanded when you select Borderless. Standard: The image is slightly enlarged and cropped to fill the sheet of paper. Mid.: Margins might be printed. (Low expansion rate.) Min.: Margins might be printed. (Lowest expansion rate.)

Expansion

Standard, Mid., Min.

Photo Print Mode

Color Restoration Setting
Setting Item Restoration Description Select On to restore faded photo.
Print settings for Photo Print mode
Setting Item Prem. Glossy, Ultra Glossy, Photo Paper, Matte 10 x 15 cm, 13 x 18 cm, A4 Borderless

Paper Size Layout

Copies your photo all the way to the edges of the paper.
Your image is slightly enlarged and cropped to fill the sheet of paper. Print quality may decline in the top and bottom areas of the printout, or the area may be smeared when printing. With Border Quality Expansion Standard Standard, Mid., Min. Copies your original with a standard 3-mm margin. Select the amount the image is expanded when you select Borderless. Standard: The image is slightly enlarged and cropped to fill the sheet of paper. Mid.: Margins might be printed. (Low expansion rate.) Min.: Margins might be printed. (Lowest expansion rate.)

Setup Mode

Ink Levels Maintenance
Check the ink cartridge status. Nozzle Check Head Cleaning LCD Brightness Head Alignment Change Ink Cartridge Language Display Format Print a nozzle check pattern to check the condition of the print head. Clean the print head to improve the condition of the print head. -10 to +10 Adjust the alignment of the print head. Change ink cartridges before they are expended. English, French, German, Italian, Spanish, Portuguese, Dutch, Russian 1up with Info, 1up without Info, 9up
PictBridge Setup Restore Default Settings
Set the print settings when printing with a PictBridge device. Reset the LCD panel settings to the factory default settings.
Supply Ink Cartridges Printer Name Stylus CX8300 Series Stylus DX8400 Series Black T0731 T0731H T0711 T0711H Cyan T0732 T0712 Magenta T0733 T0713 Yellow T0734 T0714
Available ink cartridge sizes vary by location.

Belkin Print Server F1UP0002 with Epson DX-8400
Network issues with O2 Wireless Router
The print server works with either WEP or WPA encryption. The O2 Router works with WEP, WPA, WPA2 and WPA+WPA2 encryption. In theory both should be happy with the Print Server using WPA and the O2 Router using WPA+WPA2 however this didnt work! In this scenario, the O2 Router reports the Print Server having an unknown interface (it should say WLAN) and Belkin Print Server Manager doesnt see the Print Server, however the Print Servers Wireless LED suggests it has connected ok. Learning: The network has to be run as WPA encryption as a maximum.
Installation from XP environment
Install from CD or from the Belkin site as directed. Manual, Firmware, Utilities are available here:http://www.belkin.com/uk/support/article/?lid=enu&pid=F1UP0002uk&aid=6369&scid=0 However, I found the best way of setting up the Print Server was:1. Install Belkin software 2. Connect the Print Server wired via RJ45 connection to the Network Router, assuming the O2 Router will act as the DHCP server issuing an IP address to the Print Server. 3. Find the IP address allocated to the Print Server (named MFD8FD74 or similar) Start All-in-one print manager and select the Print Server List tab, looking for the IP address or Use the O2 Router Box manager, looking for the IP address, eg. 192.168.1.65 4. Using an Internet Browser, start the Web-based Print Server manager go to the address given to the Print Server, eg. http://192.168.1.65 Username: Admin Password: 1234
a. Under Wireless, Channel and SSID i. Click [Site Survey] and when you see your server select that row ii. That should fill in Function: Auto Mode: Infrastructure SSID: O2Wirelessblabla Channel Number: ignore this it reports the wrong channel number! iii. Save but reboot later b. Under Encryption i. ii. iii. iv. 05 September 2009 Mode: WPA-PSK WPA Algo: TKIP WPA Pre-shared key: your network key Save and reboot later Page 1 of 2 David Brewerton
c. Setup TCP/IP i. Select - Enable TCP/IP settings automatically (use DHCP/BOOTP) ii. Save and reboot now! d. When the Print Server has rebooted, unplug the RJ45 connection so that it should be on wireless now. Check that the web-based Print Server Manager is still accessible in your Internet Browser. 5. At this point its probably safest to fix the IP address given to the Print Server by the Router. I did this in the Router Manager Config for the device as this still uses the Router as the network manager. Fixing the IP Address in the Print Server Manager doesnt show the device on the Router!
Set up printing services on XP computer
1. Install the All-in-One Utilities from CD or from. http://www.belkin.com/uk/support/article/?lid=enu&pid=F1UP0002uk&aid=6369&scid=0 2. Go to the Add Printer wizard and Add a PlugNPlay Local printer might take a bit of finding it but it should work! 3. Start the Belkin All-in-One Print Manager to connect the print queue with the Print Server devices IP address. a. and go to the Auto Connect List tab b. Click Add i. Select your Print Server row ii. Select your new Print Queue c. Click ok 4. It should now work try printing!
Set up printing services on Linux Xandros (Debian Etch) computer
1. Assuming CUPs is installed ok (it should be on the standard EEE PC 901 Xandros Linux build). The Pipslite printer driver is available from www.avasys.jp/lx-bin2/linux_e/spc/DL1.do 2. Select Image Scan for Linux & Photo Image Print System Lite for Epson Stylus DX-8400 3. Fill in the distribution info and select Debian Etch distribution. Follow the Read me guide for installing. 4. Set up the Printer a. Add Network Printer type Other b. Name: BelkinPrintQueue Connection: AppSocket/HP JetDirect (socket) Path: lpd://192.168.1.65 c. Pick Stylus CX4800 from the list as DX-8400 isnt listed! Use default Foomatic+gutenprint-ijs.5.0 d. Print a test print!