Proof Sign-off: t.Ishiguri CRE Nakano H.Kimura K.Norum

R4C705P Plus_UK

SETUP.FM 7/12/01

Rev. C

A2 size
Setting Up the Printer Hardware
Warnings, Cautions, and Notes
Warnings must be followed carefully to avoid bodily injury.
Cautions must be observed to avoid damage to your equipment.
Notes contain important information and useful tips on the operation of your printer.

English

1. Unpack
2. Remove protective materials
3. Attach the printer parts

4. Connect the printer

Connect the printer cable to the ports on the computer and the printer.
Power cord may come attached in some countries.

Setup Quick Guide

Caution: If the printer comes on when you plug in the power cord, turn off the printer by holding down the power button until light goes out.
Installing the Printer Software and the Ink Cartridges

For Windows

1. Make sure that printer is off, then turn on your computer. 2. Insert the printer software CD in the CD-ROM drive. If the Installer dialog box does not appear, double-click EPsetup.exe in the CD-ROM. 3. Select Install Printer Driver/Utility, and click. 4. Make sure that the Install Location box displays the correct drive, then click Install. 5. Follow the on-screen instructions to install the printer software. 3. Place the ink cartridges into the cartridge holders. Do not apply excessive force to the cartridges. Once paper is loaded, follow these steps to check the print head nozzles.

For Windows users

1. Click the Start button, point to Settings, and click Printers. 2. Select the icon for your printer, then click Properties on the File menu. Then click the Utility tab. 3. Click the Nozzle Check button, and follow the on-screen instructions. 4. When you are finished, click OK to close the Properties dialog box. Your printer is now set up and ready to use.

2. Select the printer

After you have installed the printer software, you need to select your printer. 1. Press the P power button to turn on the printer. The print head moves to the ink cartridge installation position. 2. Choose Chooser from the Apple menu. Then, select the icon for your printer and the port that your printer is connected to. 3. Close the Chooser.
Note: Install both ink cartridges. The printer will not work with only one cartridge. 4. Close the ink cartridge clamps until they lock into place. 5. Close the printer cover. 6. Press the b maintenance button. The printer moves the print head and begins charging the ink delivery system. This process takes about one and half minutes. While charging, the P power light flashes and the printer produces a variety of mechanical sounds. This is normal.
4. Click OK in the dialog box that appears. 5. When a message appears prompting you to turn on the printer, press the P power button. The print head moves to the ink cartridge installation position and the Setup utility starts automatically.
Read the Safety Instructions on the back of this sheet when setting up and using this printer.

For Macintosh users

1. Select Page Setup in the Finders File menu. 2. Click the
Caution: Do not move the print head by hand, as this may damage the printer.

utility icon.

6. Follow the Setup utilitys on-screen instructions to install the ink cartridges. Note: If the Setup utility does not start, follow the instructions in the Macintosh section of this sheet, beginning from 3. Install the ink cartridges. When ink cartridge installation is complete, proceed to Load paper and check the print head nozzles on this sheet.
3. Install the ink cartridges
1. Open the printer cover, then open the ink cartridge clamps, as shown in the illustrations.

printer cover

Caution: Do not turn the power off during the ink charging process. Do not load paper until ink charging is complete.
3. Click the Nozzle Check button, and follow the on-screen instructions. 4. When you are finished, click OK to close the utility dialog box. Then click OK to close the Page Setup dialog box. Your printer is now set up and ready to use.
When the ink charging process is finished, the P power light stops flashing and remains on.
Load Paper and check the print head nozzles

Ink cartridge clamps

For Macintosh
1. Install the printer software
Caution: Turn off all virus protection programs before you install the printer software.
Before checking the print head nozzles, you need to load paper as shown below. When loading the paper, make sure that the paper stack fits under the tabs inside the edge guides and does not exceed the loading limit indicated by the arrow mark on the left edpge guide. To adjust the left edge guide, hold down the locking tab and slide the guide against the paper stack. Make sure that the position of the edge guide allows the paper to move up and down freely.

left edge guide printable side up tab

Turning off the printer

To turn off the printer, hold down the P power button until the light goes out.

Color Ink Jet Printer

1. Make sure that printer is off, then turn on your Macintosh and insert the printer software CD in the CD-ROM drive. 2. Double-click the Printer software folder, then double-click the Installer icon inside it. 3. Click Continue.
2. Remove only the yellow tape from the new ink cartridges.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION's operating and maintenance instructions. SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION. SEIKO EPSON CORPORATION shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as EPSON Approved Products by SEIKO EPSON CORPORATION. EPSON is a registered trademark and EPSON Stylus is a trademark of SEIKO EPSON CORPORATION. Microsoft and Windows are registered trademarks of Microsoft Corporation. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
locking tab output tray extension

Read this side first!

Print quality is determined by the driver settings and the paper. See the online Reference Guide for details on driver settings and available media. Also visit the EPSON Web Site for the latest information.

4014637-00 xxx

4014637 1-F

Rev.0 BK2

Rev.0 C

Rev.0 M

Rev.0 Y

Rev.0 BK

QUICK.FM 7/16/01

Quick Guide

Using the Online Reference Guide
Follow these steps to access the online Reference Guide. 1. Insert the printer software CD in the CD-ROM drive. 2. For Windows, select Users Manual in the Installer dialog box and click. For Macintosh, double-click Users Manual.
Accessing the Printer Software
The printer software includes a printer driver and utilities. The printer driver lets you choose from a wide variety of settings to get the best results from your printer. The printer utilities help you check the printer and keep it in top operating condition. Access the printer software as explained in this section.

Replacing Ink Cartridges

You can replace an ink cartridge by using the Status Monitor utility installed on your computer, or by using the printer's control panel. To replace an ink cartridge or check ink levels using the Status Monitor utility, refer to Using the Status Monitor in the online Reference Guide. To replace an ink cartridge using the printer's control panel, follow the steps in this section. Note: You cannot continue printing with one ink cartridge empty, even if the other cartridge still contains ink. Before printing, replace the empty cartridge. In addition to the ink used during document printing, ink is consumed during the print head cleaning operation, during the self-cleaning cycle which is performed when the printer is turned on, and during ink charging when the ink cartridge is installed in the printer. 1. Make sure that the printer is on, but not printing. Then open the printer cover. 2. Press the b maintenance button. The print head moves to the ink replacement position. When both cartridges are out of ink, the cartridge moves to the black ink cartridge replacement position first. Press the b maintenance button again after replacing the black ink cartridge to switch to the color ink cartridge replacement position.

Safety Instructions

Read all of the instructions in this section when setting up and using your printer.
When choosing a place for the printer
Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer away from direct sunlight, strong light, or heat sources. Avoid places subject to dust, shocks, and vibrations. Leave enough room around the printer to allow for sufficient ventilation. Place the printer near a wall outlet where the plug can be easily unplugged. Place the printer on a flat, stable surface that extends beyond the printer base in all directions. The printer will not operate properly if it is tilted at an angle.

There are three ways to access the printer software. From Windows applications 1. From the File menu of your application, click Print. The Print dialog box appears. 2. Select your printer, then click Properties, Printer, Setup, or Options to access the printer software. (Depending on your application, you may need to click a combination of these buttons.) Note: When you access the printer software from a Windows application, the settings that you make apply only to the application you are using. From the Start menu 1. Click Start, point to Settings, then click Printers. To view the guide from the CD, click View Reference Guide. To install the guide, click Install Reference Guide and follow the on-screen instructions. When installation is complete, an ES C40 Series icon (Windows) or a View Reference Guide icon (Macintosh) appears in the EPSON folder. Double-click the icon to open the guide. 2. Select your printer, then click Properties on the File menu. If you are a Windows 2000 user, select your printer, then click Printing Preferences on the File menu. From the taskbar 1. Right-click the printer icon on the taskbar. 2. Select Printer Settings.
When choosing a power source
Use only the type of power source indicated on the printers label. Do not use a damaged or frayed power cord. If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed the cords ampere rating. Also, make sure that the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlets ampere rating. If you plan to use the printer in Germany, the building installation must be protected by a 10 or 16 amp circuit breaker to provide adequate short-circuit protection and over-current protection for this printer.
Caution: Do not move the print head by hand, as this may damage the printer. Always press the b maintenance button to move it.
When handling ink cartridges
Do not open the ink cartridge packages until just before you install them. Keep ink cartridges out of the reach of children. Do not allow children to drink from or otherwise handle the cartridges. Be careful when you handle used ink cartridges, as there may be some ink remaining around the ink supply port. If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor immediately. Do not shake the ink cartridges; this can cause leakage. You must remove the yellow tape seals from the cartridges before installing them; otherwise, the cartridges will become unusable. Do not remove the blue portion of the tape seal from the top of the cartridges. Do not remove the tape seals from the bottom of the cartridges.

3. Install the new ink cartridges as explained on the reverse side of this sheet in the 3. Install the ink cartridges section.
Technical Support Web Site
EPSONs Technical Support Web Site provides you with tips to help solve any problems you may encounter when using your printer. Access the Technical Support Web Site in one of the following ways: From Status Monitor 3 Click Technical Support in the Status Monitor 3 dialog box. From your printer software Click Technical Support on the Main menu of the printer software. For further information on the customer support services available in your area, see the online Reference Guide.
Customer Support: The United Kingdom and the Republic of Ireland (www.epson.co.uk); Australia (www.epson.com.au); Singapore (www.epson.com.sg); Hong Kong (www.epson.com.hk); Malaysia (www.epson.com.my); India (www.epson.co.in); Philippines (Phone: (632) 813-6552)
You can access the various printer software dialog boxes as described below.
Dialog Box Print Page Setup Layout Utility How to Access Click Print on the File menu of your application or click Options in the Page Setup dialog box. Click Page Setup on the File menu of your application. Click the Click the Layout icon button in the Print dialog box. Utility icon button in the Print or Page Setup dialog box.

Panel Operation

Button power maintenance Function Turns the printer on and off. To turn off the printer, hold down the P power button until the light goes out. Loads or ejects paper if pressed and released within three seconds. Resumes printing if pressed after a paper out error.

When using the printer

See the online Reference Guide for details. Do not put your hand inside the printer or touch the ink cartridges during printing. Do not block or cover the openings in the printers cabinet. Do not attempt to service the printer yourself. Unplug the printer and refer servicing to qualified service personnel under the following conditions: The power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the cabinet damaged; the printer does not operate normally or exhibits a distinct change in performance. Do not insert objects through the slots in the printers cabinet. Take care not to spill liquid on the printer.
EPSON's Technical Support Web Site provides help with problems that cannot be solved using the troubleshooting information in your printer documentation. To access Technical Support, insert the CD in the CD-ROM drive and double-click the Technical Support Web Site icon in the Printer Software folder. For further information on the customer support services available in your area, see the online Reference Guide.
Printing on Special Media
You can print on a wide variety of special mediaincluding ink jet paper, photo quality glossy film, photo paper, transparencies, index cards, and adhesive sheetsand several sizes of envelopes. Read the instructions in the media package first.

Error Indicators

You can identify many common problems using the lights on the printers control panel. Use the following table of light patterns to diagnose the problem, then follow the recommended corrective measures.
Lights O Problem and Solution Paper out No paper is loaded in the printer.
Information for United Kingdom Users
Use of options EPSON (UK) Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by EPSON (UK) Limited. Safety information Warning: This appliance must be earthed. Refer to the rating plate for the voltage and check that the appliance voltage corresponds to the supply voltage. Important: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: Green and yellow Earth Blue Neutral Brown Live If you have to fit a plug: As the colours of the mains lead of this appliance may not match the coloured markings used to identify the terminals in a plug, please observe the following: The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or the earth symbol (G). The blue wire must be connected to the terminal in the plug marked with the letter N. The brown wire must be connected to the terminal in the plug marked with the letter L. If the plug is damaged, replace the cord set or consult a qualified electrician. Replace fuses only with fuses of the correct size and rating.
Keep this sheet handy for quick reference.
Caution: Cleaning sheets packaged with EPSON special media should not be used with this printer. The cleaning function performed by these sheets is not necessary with this type of printer, and the sheets could jam in the printer.
Check EPSON Status Monitor 3* or EPSON StatusMonitor*. Load paper in the sheet feeder, then press the b maintenance button. The printer resumes printing and the light goes out. O

Paper jam

Paper has jammed in the printer.
Load the media printable side up in the sheet feeder. See the instructions packed with the media to determine which side is the printable side.The loading capacity varies by media. For more details on using special media, see Paper Handling in the online Reference Guide. Make sure that the paper stack fits under the tabs inside the edge guide, and does not exceed the loading limit indicated by the arrow mark on the left edge guide.
Check EPSON Status Monitor 3* or EPSON StatusMonitor*. Press the b maintenance button to eject the jammed paper. If the error does not clear, open the printer cover and remove all of the paper inside, including any torn pieces.Then reload the paper in the sheet feeder and press the b maintenance button to resume printing. F

Ink low

The black or color ink cartridge is nearly empty.
Obtain a replacement black or color ink cartridge. To determine which cartridge is nearly empty, check the ink level using EPSON Status Monitor 3* or EPSON StatusMonitor*. O

Ink out

The black or color ink cartridge is empty or is not installed.
Replace the black or color ink cartridge with a new one. To determine which cartridge is empty, check the ink level using EPSON Status Monitor 3* or EPSON StatusMonitor*. N O

Carriage error

The print head carriage is obstructed by jammed paper or other foreign material and cannot return to the home position.
Turn off the printer**. Open the printer cover and remove any paper from the paper path by hand.Then, turn the printer back on. If the error does not clear, contact your dealer. F F

Unknown printer error

An unknown printer error has occurred.
Turn off the printer** and contact your dealer.
O = on, N = off, F = flashing * EPSON Status Monitor 3 is for Windows; EPSON StatusMonitor is for Macintosh. ** To turn off the printer, hold down the P power button until the light goes out. Copyright 2001 by SEIKO EPSON CORPORATION, Nagano, Japan.

Printed in xxxx

4014637 1-B

101 102

EPSON STYLUS C20UX,C20SX,C40UX,C40SX

Rev.01 10317

for 220V

for 120V

except ETT
400 forEURO,EAI(220V),ASIA(220V), EAL,RUSSIA

502 513

513 X 2

Rev.05

10317 C413-MECH-075

606 604

600 603
EPSON STYLUS C20SX,C40SX No.4

Rev.02

10317 (C413-MECH-08)

700 701

708 707

Rev.03

C413-MECH-09
Part Code Part Name FHOUSING,UPPER,USB COVER PRINTER;ECP PAPER SUPPORT STACKER LOGO PLATE 10X40;C,2COLOR SEIKEI BUTTON,SW BOARD ASSY.,MAIN PRINTER MECHANISM(ASP)MA410-103 PRINT HEAD HOLDER,I/C COVER CARTRIDGE,BK COVER CARTRIDGE,C CABLE,HEAD SHEET,PROTECT,CABLE HEAD HOLDER,SHAFT ASSY. MOTOR ASSY.,CR FOOT FRAME,FRONT ASSY.,C413,ASP C.B.S-TITE SCREW,3X6,F/ZN-3C TIMINGBELT POROUS PAD,CAP,LOWER POROUSPAD,INKEJECT POROUS PAD,TUBE,STOPPER;D SHIELD PLATE,M/B C.B.P-TITE SCREW,3X8,F/ZN-3C C.B.S-TITE SCREW,3X6,F/ZN-3C MOUNTING PLATE,M/B,ES2 EDGE GUIDE HOPPER PAD,HOPPER COMPRESSION SPRING,2.50 FRAME,ASF HOLDER,PAD PAD,LD;D TORSION SPRING,29.1 C.B.S-TITE SCREW,3X6,F/ZN-3C C.B.P-TITE SCREW,3X8,F/ZN-3C C.B.S-TITE(P4)SCREW2,3X6,F/ZN-3C PAD,ACCESSORY PLASTIC PROTECTIVE BAG,360X680X0.03T PLASTIC PROTECTIVE BAG 180X260X0.03T PAD,CR;B I/C WITHOUT INDIVIDUAL I/C WITHOUT INDIVIDUAL CLEANING SHEET,L SOFTWARE CD-ROM,EFGIPSD APPLICATION CD-ROM,EULDSG SUPPLEMENT WARRANTY CARD;EURO B SETTING UP MANUAL SETTING UP MANUAL SETTING UP MANUAL

Ref No.

Category
Qty Remark 1 migration LANGUAGES 1 1
100 Case 101 Case 102 Case 103 Case 104 Case 105 Case 200 Electronic Parts 500 Mechanism Parts 501 Mechanism Parts 502 Mechanism Parts 503 Mechanism Parts 504 Mechanism Parts 505 Mechanism Parts 506 Mechanism Parts 508 Mechanism Parts 509 Mechanism Parts 511 Mechanism Parts 512 Mechanism Parts 513 Mechanism Parts 514 Mechanism Parts 516 Mechanism Parts 600 Mechanism Parts 601 Mechanism Parts 602 Mechanism Parts 603 Mechanism Parts 604 Mechanism Parts 606 Mechanism Parts 700 Mechanism Parts 701 Mechanism Parts 702 Mechanism Parts 703 Mechanism Parts 704 Mechanism Parts 705 Mechanism Parts 706 Mechanism Parts 707 Mechanism Parts 708 Mechanism Parts 709 Mechanism Parts 710 Mechanism Parts 4 Packing Material 5 Packing Material 6 Packing Material 7 Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material

6022804

SETTING UP MANUAL SETTING UP MANUAL SETTING UP MANUAL SETTING UP MANUAL WARNING SHEET SUPPLEMENT SUPPLEMENT POWER SUPPLY ASSY.,C413,ASP;220V GREASE G-58 Shipping Liquid,S46,18kg Shipping Liquid,S46,1kg
NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material NON FIG Packing Material 300 Power Supply NON FIG Tools NON FIG Tools NON FIG Tools Ref No. Category

1 Qty Remark

Part Code Part Name