Continuous

Ink for

Supply System

Epson Stylus C67 Installation Instruction
For ST Prefilled Version With Auto Reset Chips
This Version of the Continuous Ink Flow System comes with Prefilled Cartridges and Auto Reset Chips. You just need to fill the Reservoir bottles and print! The whole operation is very easy. Its really an effective tool to save your money.

CIS for

EPSON stylus C67 Instruction
Thank you for purchasing ST Continuous Ink Supply System. We appreciate your support and will try our best to make your experience with our products a pleasant one. Printing has been a different experience ever since you installed ST Continuous Ink Supply system on your own printer. Just imagining being able to print without regard to the ink level in those expensive little cartridges. Please take your time installing ST Continuous Ink Supply system. Do not remove your old cartridge until you have the ST CIS system primed and ready to install (to prevent the drying of heads). In addition, make sure you are getting perfect nozzle checks before installing the ST CIS system. The ST CIS system wont be able to work properly if the nozzles are previously clogged. Most people get a perfect nozzle check the first time after installing the ST Continuous Ink Supply system; others may need to run two or three cleaning cycles or let the printer sit for a while before they get the perfect results. 1General Guide:
1) Components ACIS system 1 set DRefill Kit 4pcs B Air filters 4pcs EInstruction CD 1pc CSupport Arm 1 set
2) Opening box inspection aCheck whether all the accessories are ready. bCheck whether there's the leakage of the CISS, whether some tubes have been separated from the CISS, whether there are air bubbles in the tube (If there exists more than 20CM air space, please kindly to contact with the local dealer)

2Printer testing:

1) Check whether the printer is in normal condition, like mechanical status, lubrication status etc. 2) Print testing lines to ensure the printing head is good condition. 3) Print pictures to see whether the printing image is ok.
3Installation Procedures:

1) First step

Put the CISS on the left side of the printer. In the meantime place all the tubes at correct position.
Pull out the small rubber plug from the air hole as above picture shown.
Place 4pcs of air filters into air holes, the thicker side is down into tank.
2Second step: Remove cartridge
Press the ink cartridge replace button
Move the cartridge-car to the cartridge replace position

Unplug the power

3 Third step: Set up the Continuous Ink Supply System
Replace the spring of the cartridge-car
open the cover of cartridge to some degree angle
Insert screwdriver into the place that joint cover and cartridge-car
Circumgyrate screwdreiver deasilly
Separate the right side of cartridge-car
Take off the cover of cartridge-car
Fourth step: Set up the Continuous Ink Supply System
Remove original cartridge
Insert our no-sponge cartridge into printer carefully
Close the cover for cartridge
5) Fiveth step: Fix Support Arm

Tear off the sticker

Fix the arm on the 25cm right far from you printer

Fix the balance arm

Tear off the sticker of clamp
Attached the clamp on your printer and let it parallel with printer
6) Sixth step : Install tubeline

Insert tubelline through the arm

Finished

7) Seventh Step: Adjust the tubeline
Adjust the tubeline,remove the Cartridge-car back and forth
Make sure tubline will not meet printer when printing
Make sure the lengh of tubline is enough to reach the far left and right

Too long

Perfect

8) Eighth step

Instert the plug
Turn on the power switch check wether all thing is usual
9)Nineth step: Nozzle check

Broken line

The nozzle check patterns are in broken-line, mostly because of small dusk entered into the nozzle, after repeated cleaning, if there is still a few broken line, the nozzle check pattern, maybe it works well. pls let the printer dont work about 1 hour, then print

4Reset Procedure:

If the indicator light flashing when printing, it tells that you need to reset the chip to full status. Please turn off your printer for about 30 seconds and switch it back on. Ink meter bar shall show full ink. You can start printing as usual.

5Refill Ink:

Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill ink according to the color in short supply. Then put the rubber back. (Please keep the printer and the reservoir at the same horizontal line during the process of refilling ink.)
How to install the cover of cartridge:
Pls first install the left side of the cover into cartridge-car
Then install the other side
Adjust well the joint position
Press the right side of cover to make it install well
7Attention for maintenance: Take out the CISS including the inner cartridges and other components. Then remove support arm from printer, and place the original cartridges in. Please inquire local dealer before sending to maintenance. Notice: 1. Please dont take out cartridge at random after installing the CIS system. Keep the reservoir bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you dont want to run out of ink and draw air into the cartridge. 3. Dont place the Reservoir Bottles higher or lower much than the printer. 4. To be used in a dry place between 15 and 35 degree. Avoid exposure to direct sunlight. 5. Dont put the continuous ink supply systems reversed or leaning during the shipment. Please make sure all the ink filling holes and Ventilation holes are closed tightly during the transportation. Otherwise, the ink shall leak out. 6. Dont sway the cartridge frequently. It may cause ink leakage. 7. Dont pull out the connector of cartridge and dont tear off adhesive tape at the bottom of cartridge. Warning: 1. Not drinkable; keep it out reach of children. 2. Avoid exposure to direct sunshine and dont keep it in high or freezing temperature. 3. Avoid collision and fallen down.

400 Without ESP(Iinter),EURO 104

EPSON Stylus C67/C68/D68

Rev.01

C616-ACCE-001

106 102

C616-CASE-001

C616-ELEC-001

542 509

C616-MECH-001

702 708

704 716

709 711

C616-MECH-002
Part Code Part Name 1430806 INK CART.UNBOXED,BK-SS,PIG'T;G38K,WST,AS INK CART.UNBOXED,C-SS,PIG'T;G38K,WST,AS INK CART.UNBOXED,M-SS,PIG'T;G38K,WST,AS INK CART.UNBOXED,Y-SS,PIG'T;G38K,WST,AS HOUSING,UPPER;EDG2 COVER,INK TUBE;EDG2 COVER,I/F;EDG2 STACKER ASSY. PAPER SUPPORT ASSY.;EFS3 COVER,PRINTER;EFS3;D68P BUTTON,SW ASSY.,B BOARD ASSY.,MAIN BOARD ASSY.,PANEL PRINTER MECHANISM(ASP)MAD13-100 FOOT POROUS PAD,INK EJECT,UPPER,LARGE POROUS PAD,INK EJECT,LOWER,BIG;D POROUS PAD,INK EJECT,FB INSULATOR,FRAME,MAIN ROLLER,EJECT INKSYSTEM ASSY. PAPER GUIDE,FRONT ASSY. POROUS PAD,INK EJECT,LOWER,SMALL PROUS PAD,CAP,LOWER,SMALL POROUS PAD,TUBE,FASTEN HOLDER,SHAFT ASSY.;B FRAME,FRONT ASSY. POROUS PAD,PAPER GUIDE FRONT,LOWER SHEET,POROUS PAD,COVER DIFFUSION SHEET,INK EJECT,LOWER,ASP PRINT HEAD ASSY. SCALE,CR ASF UNIT GROUNDING PLATE,HEAD TORSION SPRING,LEVER,CARTRIDGE SHIELD PLATE,CABLE HEAD ASSY.,C616 BOARD ASSY.,ENCODER LABEL,POSITION,CARTRIDGE LEVER,CARTRIDGE HOLDER,I/C ASSY. PLATE,SLIDER TIMING BELT;E POWER SUPPLY ASSY.;D
Ref No. NON FIG NON FIG NON FIG NON FIG 300 Ref No.
Category Accessories Accessories Accessories Accessories Case Case Case Case Case Case Case Electronic Parts Electronic Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Mechanism Parts Power Supply Category

Qty Remark 1 Qty Remark

Part Code Part Name