Safety Instructions

Important Safety Instructions
Before using this printer, read and follow these safety instructions: Use only the power cord that comes with the printer. Use of another cord may cause fire or shock. Do not use the cord with any other equipment. Make sure the power cord meets all relevant local safety standards. Use only the type of power source indicated on the label. Place the printer near a wall outlet where the power cord can be easily unplugged. Do not let the power cord become damaged or frayed. Make sure the total ampere rating of the devices plugged into an extension cord or a wall outlet does not exceed the ampere rating limit. Avoid locations that are subject to rapid changes in heat or humidity, shocks or vibrations, dust, or direct sunlight. Do not block or cover openings in the case or insert objects through the slots. Place the printer on a flat, stable surface that extends beyond its base in all directions. It will not operate properly if it is tilted or at an angle. And make sure the back of the printer is at least 10 cm away from the wall for sufficient ventilation. Do not open the scanner unit while copying, printing, or scanning. Do not spill liquid on the printer. Do not use aerosol products that contain flammable gases inside or around the printer. Doing so may cause fire. Except as specifically explained in your documentation, do not attempt to service the printer yourself. Unplug the printer and refer servicing to qualified service personnel under the following conditions: if the power cord or plug is damaged; if liquid has entered the printer; if the printer has been dropped or the case damaged; if the printer does not operate normally or exhibits a distinct change in performance.
When storing or transporting the printer,
do not tilt it, stand it on its side, or turn it upside down; otherwise ink may leak from the cartridge. Be careful not to trap your fingers when closing the scanner unit. Do not press too hard on the document table when placing the originals.
Ink cartridge safety instructions
Keep ink cartridges out of the reach of
children and do not drink the ink. If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them immediately with water. If you still have discomfort or vision problems, see a doctor immediately. Do not shake ink cartridges after opening their packages; this can cause leakage. If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust and store it in the same environment as the printer. Do not touch the ink supply port or surrounding area.

Control Panel

Control panel design varies by location.

The availability of special paper varies by location. You can find the part number for the following Epson special papers on the Epson support Web site.
Choose from these paper types and settings:
Paper type Plain paper ** Epson Bright White Ink Jet Paper Epson Matte Paper-Heavyweight Epson Photo Quality Ink Jet Paper Epson Premium Glossy Photo Paper Epson Premium Semigloss Photo Paper Epson Ultra Glossy Photo Paper Epson Glossy Photo Paper Epson Photo Stickers 4 *** Epson Photo Stickers 16 *** Ultra Glossy Photo Paper PhotoStickersheets 20 sheets 1 sheet 1 sheet Prem.Glossy Matte Paper type setting Plain Paper Loading capacity * 15 mm 100 sheets 20 sheets 100 sheets 20 sheets
* The loading capacity of the rear feeder and the front paper cassette is the same except Photo Stickers. ** You can use paper with a weight of 64 to 90 g/m. *** You cannot load Photo Stickers in the front paper cassette.

Loading Paper

Into the rear feeder
1. Open and extend the paper support.
2. Move the feeder guard towards you, and then slide the edge guide.

cm (in.) and cm (in.)

Follow the same steps to load A4 paper.
3. Load the paper short edge first, even for landscape printing, with the printable side up.
The printable side is often whiter or brighter than the other side.
6. Open and extend the output tray.
4. Slide the paper to the right. c Caution:
Make sure the CD/DVD guide is not ejected before you start printing.
Make sure the Paper Feed setting is set to Rear before you start printing.
5. Slide the edge guide to the right. Make sure the paper fits under the c arrow mark inside the left edge guide. Set the feeder guard back.
Into the front paper cassette
Do not load Photo Stickers into the front paper cassette. Do not load paper into the front paper cassette that has already been printed onto one side or that has been fed through the printer once.
Align the edges of the paper before loading.
1. Pull out the front paper cassette.
5. Fit the edges of the paper snugly against the paper guides. The paper will not be loaded correctly if it overflows or does not fit properly.

6. Replace the cover. 2. Lift off the cover.
3. Pinch the knob and slide the paper guides to accommodate the paper size you are loading.
7. Insert the cassette back into the printer and keep it flat as you insert it.
4. Load paper with the printable side face down. Make sure the paper is under the c arrow mark inside the paper guide. Note:
Do not load paper above the c arrow mark inside the paper guide.
Follow the same steps to load cm (in.) and cm (in.) paper.
8. Open and extend the output tray.

c Caution:

Make sure the CD/DVD guide is not ejected before you start printing. Make sure the Paper Feed setting is set to Front before you start printing. Do not pull out the front paper cassette while the printer is operating.
Store the CD/DVD tray in a flat place. A warped or damaged CD/DVD tray may stop the printer from operating normally.
3. Place your CD/DVD on the tray.

The label surface up.

Make sure the data, music, or video is burned on your ink jet printable CD/DVDs before you print. Moisture on the printable surface may cause smearing. The printed surface is easily smeared immediately after printing. Be sure to let a CD/DVD dry completely before using it or touching the printed surface. Do not allow the printed CD/DVD to dry in direct sunlight. If the CD/DVD tray or the internal transparent compartment are accidentally printed on, immediately wipe off the ink. To print on 8-cm mini CDs, use the EPSON Print CD included in the software CD-ROM. See your online User's Guide.
4. Insert the tray into the CD/DVD guide. c Caution:
Do not insert the tray while the printer is operating, or you may damage the printer.

Loading a CD/DVD

1. Close the output tray extension.
Make sure there is no paper on the output tray.
2. Press L [CD Print] to move the CD/DVD guide. c Caution
Do not press L [CD Print] while the printer is operating. Do not touch the CD/DVD guide while the printer is operating.

Removing a CD/DVD

1. Make sure that printing is finished. 2. Remove the CD/DVD tray by pulling it straight out of the CD/DVD guide. 3. Press L [CD Print] to replace the CD/DVD guide.
Be sure to remove the CD/DVD tray after printing has finished. If you turn the printer on or off with the tray in the CD/DVD guide, you may damage the printer.

1. Make sure your printer is not printing from a computer. 2. Remove any memory cards from the printer. 3. Press F [Setup]. 4. Select PictBridge Setup, then press OK. 5. Select the print settings (& Print settings for Memory Card mode on page 42). Then press OK. 6. Connect the USB cable from your camera to the USB port on the front of the printer.

USB port

4. Follow the same steps as you would to print from the memory card (& Printing Photos on page 17).
Using PictBridge or USB DIRECT-PRINT
PictBridge and USB DIRECT-PRINT let you print your photos by connecting your digital camera directly to the printer. Make sure your camera and photos meet the following requirements.
7. Make sure your camera is turned on and use it to select the photos, adjust any necessary settings, and print your photos. See your cameras manual for details. Note:
Depending on the settings on this printer and the digital camera, some combinations of paper type, size, and layout may not be supported. Some of the settings on your digital camera may not be reflected in the output.
You can save scans of photos or documents directly to your memory card in JPEG or PDF format. You can also save photos from your memory card directly to an external storage device with a USB cable. c Caution:
Never open the scanner unit while scanning; otherwise, you may damage the printer. Do not remove the card or turn off the printer while the memory card light is flashing, or you may lose data.
Scanning a Photo / Document
If the edges of the photo are cropped off, move the original away from the corner slightly.
Using an External Storage Device
You can copy pictures from your memory card to an external storage device, such as a Zip drive, recordable CD-R/RW drive (with a USB connection), MO drive, or USB flash drive. Note:
Not all USB devices are supported. For details, contact your regional customer support.
2. Select Scan to Memory Card, then press OK.
3. Select the following settings.
Setting Format Scan Area Description Select JPEG or PDF. If the edges of the photo are light in color, select Max Area. Otherwise, select Auto Cropping. Select the type of original you placed on the document table. Select the quality of the scanned documents.

1. If the printer is connected to your computer, unplug the USB cable or turn off your computer. 2. Connect a USB cable from your storage device to the USB port on the front of the printer. (If you are using a thumb drive, plug it in directly.) Then, insert your media into the storage device.

Original

Quality
4. Press OK. The document is scanned and saved to the EPSCAN folder on your memory card. When scanning is finished, you see a confirmation screen. Note the name given to your image and its location on the card.

3. Press F [Setup].

4. Select Backup Memory Card, then press OK. 5. Select Backup Memory Card, then press OK. 6. Follow the instructions on the LCD screen. Note:
When backing up photos to a CD-R/RW, the printer creates a folder for each backup session. You can store multiple backup sessions on a CD-R/RW.

Precautions

w Warning:
If ink gets on your hands, wash them thoroughly with soap and water. If ink gets in your eyes, flush them immediately with water. If you still have discomfort or vision problems, see a doctor immediately.
Do not open the ink cartridge package until you are ready to install it in the printer. The cartridge is vacuum packed to maintain its reliability. Make sure the CD/DVD guide is not ejected. (& page 10).
Never move the print head by hand. When an ink cartridge is expended, you cannot continue printing even if the other cartridges still contain ink. Leave the expended cartridge installed until you have obtained a replacement. Otherwise the ink remaining in the print head nozzles may dry out.
1. Do one of the following: If an ink cartridge is expended: Look at the message on the LCD screen to find out which cartridge should be replaced, then press OK. If an ink cartridge is not expended: Press F [Setup]. Select Maintenance, and press OK. Select Change Ink Cartridge, and press OK. 2. Lift up the scanner unit.
Some ink is consumed each time cartridges are inserted because the printer automatically checks their reliability. For maximum ink efficiency, only remove an ink cartridge when you are ready to replace it. Ink cartridges with low ink status may not be used when reinserted. Epson recommends the use of genuine Epson ink cartridges. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior. Epson cannot guarantee the quality or reliability of non-genuine ink. Information about the ink cartridge status may not be displayed when non-genuine ink is used.
Do not touch the white flat cable inside the printer.

Backup Error Error Code xxxxxxxx
An error occurred while formatting. Formatting canceled. An error occurred while saving. Save canceled. Cannot create a folder on the memory card or disk. Operation canceled.
See the documentation for the device transmitting the data. See the documentation for the device transmitting the data. (Cause: The data is not available because of a malfunction in the device.) See the documentation for the device transmitting the data. (Cause: A part of the data is corrupted or cannot be buffered.) Make sure the storage disk has been inserted correctly.

Problems and Solutions

Setup problems
LCD screen and the mode light came on and then went out. The printers voltage may not match the outlet rating. Turn off the printer and unplug it immediately. Then, check the printer labels. c Caution
If the voltage does not match, DO NOT PLUG YOUR PRINTER BACK IN. Contact your dealer.
Error in the data. The document may not be printed correctly.
Cannot recognize the USB device.
The printer makes noise after you turn it on. Make sure the protective tape is not blocking the print head. After releasing the print head, turn off the power, wait a moment, then turn it back on. The printer makes noise after ink cartridge installation. When you install ink cartridges, the ink delivery system must be charged. Wait until charging is finished (the charging message disappears from the LCD screen), then turn off the printer. If you turn it off too soon, it may use extra ink the next time you turn it on. Make sure the ink cartridges are seated securely and no packing material remains in the printer. Open the cartridge cover and push the cartridges down until they click into place. Turn off the power, wait a moment, then turn it back on. A screen that prompts you to restart the computer did not appear after finishing the software installation. The software has not been installed correctly. Eject and insert the software CD-ROM, and then install the software again. The terms on the LCD screen are not displayed in your language. If the language displayed on the LCD screen is not the one you want, select the language you want from the Setup menu.

Make sure you select the correct paper type (& Selecting Paper on page 6). Use a support sheet with special paper or try loading your paper one sheet at a time.
When you select Standard or Best as the Quality setting, select Off as the Bidirectional setting. Bidirectional printing decreases print quality. Your printout is grainy. Make sure you select Best as the Quality setting. If you are printing or copying a photo, make sure you are not enlarging it too much. Try printing it smaller. Align the print head (& Aligning the Print Head on page 33). You see incorrect or missing colors. Clean the print head (& Cleaning the print head on page 33).
Load your paper one sheet at a time. Remove sheets from the output tray so not too many collect at a time.
The ink cartridges may be old or low on ink. Replace an ink cartridge (& Removing and Installing Ink Cartridges on page 29).
Clean the print head (& Cleaning the print head on page 33). Align the print head (& Aligning the Print Head on page 33). To clean the inside of the printer, make a copy without placing a document on the document table. Use only paper recommended by Epson and genuine Epson ink cartridges. Clean the document table. See your online User's Guide. Your printout is faint or has gaps.
Make sure you loaded the right paper and selected the correct setting for it on the LCD screen. Make sure you are not using a special effect that alters image colors, like Sepia. If your paper runs out during printing, load paper as soon as possible. If the printer is left without paper for a long period of time during printing, the colors of your next copy or print job may be incorrect. Your printout is too dark. If you are copying, press x Menu and adjust the Density. The image size or position is incorrect.
Clean the print head (& Cleaning the print head on page 33). If you notice jagged vertical lines, you may need to align the print head (& Aligning the Print Head on page 33). The ink cartridges may be old or low on ink. Replace an ink cartridge (& Removing and Installing Ink Cartridges on page 29). Make sure you select the correct paper type (& Selecting Paper on page 6). Make sure your paper is not damaged, old or dirty. Make sure the printable side (the whiter or glossier side) of the paper is facing in the right direction.
Make sure you loaded the right paper and selected the correct setting for it on the LCD screen. Make sure the original is placed correctly on the document table (& Placing Originals on the Document Table on page 12). Clean the document table. See your online User's Guide.

Movie printing problems

The same thumbnail images are printed on one sheet. When you select Print N Frames as the movie printing method, if you set a short range for the movie, the same thumbnail images are printed on one sheet. Set a longer range for the movie and try again. The printer does not play the movie. If you see a ? when you select the movie you want to play, the video codec for the movie data is not supported. Make sure that your movie data meets the requirements. See your online User's Guide. The recording time for your movie may be too long. The printer cannot recognize your movie data.

Memory Card Mode

Setting Item View and Print Photos Print All Photos Print by Date Print Index Sheet Print Proof Sheet Slide Show Scan to Memory Card Description Prints only the photos that you choose. Prints all the photos on your memory card. Prints photos by the date they ware taken. Prints thumbnails of the photos on your memory card and lets you select which ones you want to print. Prints a proof sheet of all the photos on your memory card. Displays all photos on your memory card as a slide show and prints photos that you choose. Saves the photos to a memory card.
Print settings for Memory Card mode

Menu Paper Type

Setting Item

Description

Prem.Glossy, Ultra Glossy, Photo Paper, Plain Paper, Matte, PhotoSticker16, Photo Stickers cm (in), cm (in), 16:9 wide size, A4, A6, mm Rear, Front Select Front to feed paper from the front paper cassette. Select Rear to feed paper from the rear feeder.

Paper Size

Paper Feed

Menu Layout

Setting Item Borderless
Description Prints your photo all the way to the edges of the paper.
Your image is slightly enlarged and cropped to fill the sheet of paper. Print quality may decline in the top and bottom areas of the printout, or the area may be smeared when printing. With Border Upper 1/2 Photo ID Prints your photo with a white margin at the edge. Prints your photo on the upper half of the paper. Prints photos at two sizes (35.0 45.0 mm and 50.8 50.8 mm) on the cm (in.) size photo paper. This is useful for printing identification photos. Prints multiple photos on one sheet. The size of each photo is adjusted automatically according to the number of photos to print and the size of paper. In 20-up layout, the numbers and photo dates are printed.
2-up, 4-up, 8-up, 20-up, 30-up, 80-up
When you select a number of photos less than the total, unused areas of the layout will be left blank. 16-up Places 16 images on one photo stickers sheet
When you print a photo stickers sheet, if you select only one photo, 16 copies of the same photo are printed on one sheet. If you select two or more, the number of copies you set for each is printed in a 16-up layout and unused areas of the layout are left blank. XXXXXXXX (The file name for your P.I.F. frame is displayed.) Quality Filter Enhance Prints your photo with the P.I.F. frame.

If your memory card contains P.I.F. frame data, you can choose the P.I.F. data to print with your photo from the Layout option. Select PhotoEnhance to adjust the brightness, contrast, and saturation of your photos automatically. Select P.I.M. to use your camera's PRINT Image Matching or Exif Print settings. Select the correction mode when you select PhotoEnhance from the Enhance menu. Automatic: Corrects your photos automatically. People: Makes complexions soft and warm. Landscape: Brightens up the color of the landscape. Night Scene: Enhances darkness and light for night scenes.
Draft, Standard, Best Off, Sepia, B&W PhotoEnhance, P.I.M., None

Scene Detection

Automatic, People, Landscape, Night Scene

Menu Reduce Red Eye

Off - This photo, On - Select On - This photo or On - All photos to correct red This photo, Off - All eye. photos, On - All Note: photos Depending on the type of photo, parts of the image other than the eyes may be corrected. When set to On - This photo or On - All photos, the icon is displayed on the images. Brightest, Brighter, Standard, Darker, Darkest Standard, Higher, Highest Sharpest, Sharper, Standard, Softer, Softest Highest, Higher, Standard, Lower, Lowest None, yyyy.mm.dd, mmm.dd.yyyy, dd.mmm.yyyy Off, On -

Brightness

Contrast Sharpness

Saturation

Prints the date your photo was taken.

Camera Text

Select On to print text that you added to your photo using your digital camera.
For details on the availability of this function, see your cameras documentation. Characters are printed at the bottom left along the long edge of your photo. Depending on the size of the paper and the characters, the number of printable characters changes. In some cases, text with more than 33 characters may not be printed. Fit Frame On, Off Select On, to automatically crop your photo to fit inside the space available for the layout you selected. Select Off to turn off automatic cropping and leave white space at the edges of the photo. Select On to increase the print speed. Select Off to improve the print quality (but your photos print more slowly). Select the amount the image is expanded when you select Borderless. Standard: The image is slightly enlarged and cropped to fill the sheet of paper. Mid: Margins might be printed. (Low expansion rate.) Min: Margins might be printed. (Lowest expansion rate.)

Description Select PhotoEnhance to adjust the brightness, contrast, and saturation of your photos automatically. Select P.I.M. to use your camera's PRINT Image Matching or Exif Print settings. Select the correction mode when you select PhotoEnhance from the Enhance menu. Automatic: Corrects your photos automatically. People: Makes complexions soft and warm. Landscape: Brightens up the color of the landscape. Night Scene: Enhances darkness and light for night scenes. Select On to correct red eye.

Off, On

Depending on the type of photo, parts of the image other than the eyes may be corrected. When set to On, the icon is displayed on the images. Brightness Brightest, Brighter, Standard, Darker, Darkest Standard, Higher, Highest Sharpest, Sharper, Standard, Softer, Softest Highest, Higher, Standard, Lower, Lowest -
Print settings for Print on CD/DVD
Setting Item CD/DVD 1-up CD/DVD 4-up CD/DVD Variety CD Jacket Jewel Upper CD Jacket Jewel Index
Description Prints one photo, centered on the hole in the middle of the disk. Prints four photos, with one image in each of the four quarters. Prints ten photos. Prints a photo at CD case size on one half of the paper with a perforated line. Prints 24 photos in an area twice the size of a CD case with a perforated line.
CD/DVD, Plain Paper, Prem.Glossy, Ultra Glossy, Photo Paper, Matte CD/DVD, A4 CD-R, Front, Rear Off, Sepia, B&W PhotoEnhance, P.I.M., None Select PhotoEnhance to adjust the brightness, contrast, and saturation of your photos automatically. Select P.I.M. to use your camera's PRINT Image Matching or Exif Print settings. Select the correction mode when you select PhotoEnhance from the Enhance menu. Automatic: Corrects your photos automatically. People: Makes complexions soft and warm. Landscape: Brightens up the color of the landscape. Night Scene: Enhances darkness and light for night scenes.
Paper Size Paper Feed Filter Enhance
Off - This photo, On - Select On - This photo or On - All photos to correct red This photo, Off - All eye. photos, On - All Note: photos Depending on the type of photo, parts of the image other than the eyes may be corrected.

Menu Brightness

Setting Item Brightest, Brighter, Standard, Darker, Darkest Sharpest, Sharper, Standard, Softer, Softest Highest, Higher, Standard, Lower, Lowest Inner: 18 - 46 mm (Standard: 43 mm) Outer: 114 - 120 mm (Standard: 116 mm) Standard, Darker, Darkest None, yyyy.mm.dd, mmm.dd.yyyy, dd.mmm.yyyy On, Off

Sharpness

CD Inner-Outer
Select to resize the print position for the inside and outside diameter of the CD/DVD label.

CD Density Quality Date

Draft, Standard, Best Prints the date your photo was taken.

Fit Frame

Select On, to automatically crop your photo to fit inside the space available for the layout you selected. Select Off to turn off automatic cropping and leave white space at the edges of the photo. Select On to increase the print speed. Select Off to improve the print quality (but your photos print more slowly).
Print settings for Play Movie and Print Photos
Prem. Glossy, Ultra Glossy, Photo Paper, Plain Paper, Matte, Photo Stickers cm (in), cm (in), 16:9 wide size, A4, mm Front, Rear Select Front to feed paper from the front paper cassette. Select Rear to feed paper from the rear feeder.
Your image is slightly enlarged and cropped to fill the sheet of paper. Print quality may decline in the top and bottom areas of the printout, or the area may be smeared when printing. With Border Upper 1/2 12-up Movie Enhance Off, On Prints your photo with a white margin at the edge. Prints your photo on the upper half of the paper. Prints 12 photos. Adjusts the image and improves its quality when set to On. This option is only available when the Print Method is set to Print 1 Frame. -

Quality Filter Enhance

Draft, Standard, Best Off, Sepia, B&W PhotoEnhance, None Select PhotoEnhance to adjust the brightness, contrast, and saturation of your photos automatically. Select P.I.M. to use your camera's PRINT Image Matching or Exif Print settings. Brightest, Brighter, Standard, Darker, Darkest Standard, Higher, Highest Sharpest, Sharper, Standard, Softer, Softest Highest, Higher, Standard, Lower, Lowest On, Off -
Select On, to automatically crop your photo to fit inside the space available for the layout you selected. Select Off to turn off automatic cropping and leave white space at the edges of the photo. Select On to increase the print speed. Select Off to improve the print quality (but your photos print more slowly). Select the amount the image is expanded when you select Borderless. Standard: The image is slightly enlarged and cropped to fill the sheet of paper. Mid: Margins might be printed. (Low expansion rate.) Min: Margins might be printed. (Lowest expansion rate.)

Standard, Mid., Min.

Setup Mode
Ink Levels Maintenance Nozzle Check Head Cleaning Head Alignment Change Ink Cartridge Thick Paper Language Off, On English, German, Spanish, Portuguese, French, Italian, Dutch, Russian, Korean, Traditional Chinese, Simplified Chinese (The languages displayed vary by location.) None, Memory Card Data 1-up with Info, 1-up without Info, View Thumbnail Images Screen Saver Settings Display Format CD/Sticker Position PictBridge Setup Backup Memory Card Bluetooth Settings Restore Default Settings CD/DVD, Stickers For details on the setting items, see Print settings for Memory Card mode on page 42. Backup Memory Card, Folder Select For details on the setting items, see your online User's Guide.
Supply Ink Cartridges Printer Name RX 685 Series RX 690 Series Black T0801 T0811 T0821 Cyan T0802 T0812 T0822 Magenta Yellow T0803 T0813 T0823 T0804 T0814 T0824 Light Cyan T0805 T0815 T0825 Light Magenta T0806 T0816 T0826

EPSON CD/DVD Label Direct-Printable Printer Information February, 2009 FY Product Name of each area <A> EAI Latin N/A N/A N/A N/A Epson Stylus Photo 960 N/A N/A N/A Epson Stylus Photo 900 Epson Stylus Photo 900 N/A N/A Epson Stylus Photo R800 N/A N/A Epson Stylus Photo R300 Epson Stylus Photo R300M Epson Stylus Photo R200 Epson Stylus Photo R200 N/A N/A Epson Stylus Photo R1800 N/A N/A Epson Stylus Photo R320 Epson Stylus Photo R320 N/A Epson Stylus Photo RX700 N/A N/A N/A N/A Epson Stylus Photo R220 Epson Stylus Photo R220 Epson Stylus Photo R340 Epson Stylus Photo R340 <E> Euro Pacific/Asia N/A N/A N/A Epson Stylus Photo 2100 Epson Stylus Photo 950 N/A N/A N/A Epson Stylus Photo 900 Epson Stylus Photo 900 N/A N/A Epson Stylus Photo R800 Epson Stylus Photo R800 N/A Epson Stylus Photo R300 Epson Stylus Photo R310 Epson Stylus Photo R200 Epson Stylus Photo R210 N/A N/A Epson Stylus Photo R1800 Epson Stylus Photo R1800 N/A Epson Stylus Photo R320 N/A N/A Epson Stylus Photo RX700 Epson Stylus Photo RX700 N/A N/A N/A Epson Stylus Photo R220 Epson Stylus Photo R230 Epson Stylus Photo R340 Epson Stylus Photo R350 Disc Center x/y Position (physical) PM-900C/Opt 141/139 PM-920C 141/139 PM-890C 141/139 PM-4000PX 75/67.5 PM-950C 75/67.5 <J> Japan PM-970C PM-980C PM-870C PM-930C PM-940C PX-G900 PM-G800 PM-D750 PM-G700 PM-D1000 PX-G920 PX-G5000 PM-G720 PM-D770 PM-G820 PM-A900 PX-G930 PM-A950 PX-G5100 PM-G730 PM-D800 75/67.5 75/67.5 141/139 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 Tray Type Type1 Type1 Type1 Type2 Type2 Type2 Type2 Type1 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2

05 N/A 08 08

Epson Stylus Photo RX640 Epson Stylus Photo RX650 Epson Stylus Photo 1400 Epson Stylus Photo 1400 Epson Stylus Photo 1410 Epson Stylus Photo 1410 N/A N/A Epson Stylus Photo 1390 Epson Stylus Photo R380 Epson Stylus Photo R360 N/A Epson Stylus Photo R390 N/A N/A N/A N/A Epson Stylus Photo R260 Epson Stylus Photo R265 Epson Stylus Photo R270 Epson Stylus Photo R270 Epson Stylus Photo RX580 Epson Stylus Photo RX560 Epson Stylus Photo RX590 Epson Stylus Photo RX590 N/A N/A Epson Stylus Photo R2880 Epson Stylus Photo R2880 N/A Epson Stylus Photo R2880 Epson Stylus Photo R1900 Epson Stylus Photo R1900 N/A Epson Stylus Photo R1900 Epson Stylus Photo RX680 Epson Stylus Photo RX685 N/A Epson Stylus Photo RX690 Epson Stylus Photo RX595 Epson Stylus Photo RX585 Epson Stylus Photo RX610 Epson Stylus Photo RX610 Epson Stylus Photo R280 Epson Stylus Photo R285 Epson Stylus Photo R290 Epson Stylus Photo R290 N/A N/A Artisan 700 Epson Stylus Photo PX700W Epson Stylus Photo TX700W Epson Stylus Photo N/A N/A Epson Stylus Photo Artisan 800 N/A PX800FW Epson Stylus Photo N/A N/A
PM-A890 PM-G4500 N/A PM-D870 PM-A970 PM-T990 PM-G850 PM-A820 PM-A920 PX-5600 PX-G5300 PM-A940 PM-A840 PM-G860 PM-T960 EP-801A PM-A840S EP901A/901F EP-301
75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5 75/67.5
Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2 Type2
* = Type 1 Tray Type was supported by older models. Newer printers support Type2 Tray Type