USB Data Card Programmer

users manual and installation guide

USB DCP Cover.indd 1

12/18/2002, 4:13:24 PM
Copyright 2001-2002 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 E 151st Street, Olathe, Kansas 66062 U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax. 913/397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL U.K. Tel. 44/1794.519944 Fax.44/1794.519222 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax. 886/2.2642.9099 All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed for personal use, provided that such electronic or printed copy of this manual contains the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual is strictly prohibited. Information in this manual is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes. Visit the Garmin web site (www.garmin.com) for current updates and supplemental information concerning the use and operation of this and other Garmin products. Garmin and StreetPilot are registered trademarks, MapSourceTM is a trademark of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin. Windows 95, Windows NT, Windows 98, Windows ME, Windows 2000, and Windows XP are registered trademarks of Microsoft Corporation. December 2002 Part Number 190-00201-00 Rev. C Printed in Taiwan

USB DCP Cover.indd 3

12/18/2002, 4:13:28 PM

FCC Compliance

FCC Compliance This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE (home or ofce interference requirements are more stringent than outdoor requirements). Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The USB Data Card Programmer does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations.

USB DCP Cover.indd 4

Thank you for choosing the Garmin USB Data Card Programmer or the Garmin StreetPilot III with Mini-USB Data Card Programmer. To get successful results from your new USB Data Card Programmer, take time to read through this users manual in order to fully understand all of the operating procedures. This manual is organized into three sections: The Introduction section provides licensing agreement information and a description of the programmer. The Installation section introduces you to basic features and procedures for programmer setup. The Trouble Shooting section contains information for nding solutions to installation and operating problems.
Standard Package Contents (USB Data Card Programmer)
Introduction About This Manual
Minimum System Requirements
USB Data Card Programmer CD-ROM with USB Device Drivers for Windows 98/ME, 2000, and Garmin MapSourceTM Upgrade Software including USB Support. (The USB drivers are also on the MapSource City Navigator CD-ROM or MapSource Setup CD-ROM, if applicable.) Users Manual MapSource Users Manual Addendum for the USB Data Card Programmer
IBM-Compatible PC with Pentium processor, 16 Megabytes RAM, CD-ROM drive, Mouse or other pointing device, 256-color display adapter (24-bit color recommended) and monitor with 640 x 480 resolution or higher, and up to 20 Megabytes free hard drive space. A 32 bit operating system such as Windows 98/ME, Windows 2000, or Windows XP. Universal Serial Bus port (USB). The USB Data Card Programmer is not designed to operate with Windows 95 or Windows NT. Software Requirements Existing installation of Garmin MapSource upgraded to Version 3.04 or later.

USB DCP Manual.indd i

12/18/2002, 4:14:33 PM
Introduction Software License Agreement
THIS SOFTWARE IS OWNED BY GARMIN CORPORATION (GARMIN) AND IS PROTECTED UNDER COPYRIGHT LAWS AND INTERNATIONAL COPYRIGHT TREATIES. THIS SOFTWARE IS LICENSED, NOT SOLD. THIS SOFTWARE IS PROVIDED UNDER THE FOLLOWING LICENSE WHICH DEFINES WHAT YOU MAY DO WITH THE PRODUCT AND CONTAINS LIMITATIONS ON WARRANTIES AND/OR REMEDIES. IMPORTANT: CAREFULLY READ THIS LICENSE BEFORE USING THIS PRODUCT. INSTALLING, COPYING, OR OTHERWISE USING THIS PRODUCT INDICATES YOUR ACKNOWLEDGMENT THAT YOU HAVE READ THIS LICENSE AND AGREE TO ITS TERMS. IF YOU DO NOT AGREE, RETURN THE COMPLETE PRODUCT TO Garmin INTERNATIONAL, INC. CUSTOMER SERVICE, 1200 EAST 151st STREET, OLATHE, KS 66062 WITHIN 10 DAYS OF THE DATE YOU ACQUIRED IT FOR A FULL REFUND. 1. LICENSE: Garmin (we or us) provides you with storage media containing computer software (the Program) which may also include digital cartographic data and on-line or electronic documentation, and printed materials together called (the Product) and grants you a limited non-exclusive license to use the Product in accordance with the terms of this license agreement. The copyright and all other rights to the Product shall remain with us. You must reproduce any copyright or other notice marked on the Product on all copies you make. 2. YOU MAY: a) install and use one copy of the Product on a single computer or network. This copy is to be used by only a single user at a time. If you wish to use the Product for more users, you will need an additional license for each user. b) make one copy of the Product for archival or backup purposes. c) use a copy of the Product on a home or portable computer if that copy is never loaded at the same time it is loaded on your primary computer. d) transfer the Product to someone else only if you assign all of your rights under this License, cease all use of the Product, erase or destroy any copy (including the hard disk copy) made in support of your use of the Product, and ensure that the other person agrees to the terms of this License. 3. YOU MUST NOT: a) make copies of the Product except as expressly permitted in Section 2 of this License. b) translate, reverse engineer, decompile, or disassemble the Product except to the extent the foregoing restriction is expressly prohibited by applicable law. c) rent, lease, loan, sub-license, distribute, assign, or transfer the Product except as set out in Section 2 (d) above. d) modify the Product or merge all or any part of the Product with another program.

USB DCP Manual.indd ii

12/18/2002, 4:14:36 PM
4. TERM: This License shall continue for as long as you use the Product. However, this License will terminate automatically without notice from Garmin if you fail to comply with any of its terms or conditions. You must agree, upon terminations, to destroy all copies of the Product. The Limitations of Warranties and Liability set out below shall continue in force even after any termination. 5. LIMITATION OF WARRANTIES AND LIABILITY: THE PRODUCT IS PROVIDED ON AN AS IS BASIS WITHOUT ANY WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABLE QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THOSE ARISING BY LAW, STATUTE, USAGE OR TRADE, OR COURSE OF DEALING. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE PRODUCT IS ASSUMED BY YOU. NEITHER WE NOR OUR DEALERS OR SUPPLIERS SHALL HAVE ANY LIABILITY TO YOU OR ANY OTHER PERSON OR, ENTITY FOR ANY INDIRECT, INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, LOSS OF REVENUE OR PROFIT, LOST OR DAMAGED DATA OR OTHER COMMERCIAL OR ECONOMIC LOSS, EVEN IF WE HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR THEY ARE FORESEEABLE. WE ARE ALSO NOT RESPONSIBLE FOR CLAIMS BY A THIRD PARTY. OUR MAXIMUM AGGREGATE LIABILITY SHALL NOT EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. THE LIMITATIONS IN THIS SECTION SHALL APPLY WHETHER OR NOT THE ALLEGED BREACH OR DEFAULT IS A BREACH OF FUNDAMENTAL CONDITION OR TERM OF A FUNDAMENTAL BREACH. SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 6. RESTRICTED RIGHTS: If this Product is acquired by or for the U.S. Government, then it is provided with Restricted Rights. Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraphs (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the Commercial Computer Software - Restricted Rights at 48 CFR 52.227-19, or clause 18-52-227-86 (d) of the NASA Supplement to the FAR, as applicable. The contractor/manufacturer is Garmin International, Inc. 1200 E. 151st Street, Olathe, KS 66062, USA. 7.) EXPORT CONTROLS: You agree not to export or re-export the Product to any country in violation of the export control laws of the United States of America. 8. GENERAL: This License is the entire agreement between us, superseding any other agreement or discussions, oral or written, and may not be changed except by a signed agreement. This License shall be governed by and construed in accordance with the laws of the State of Kansas, United States of America. If any provision of this License is declared by a court of competent jurisdiction to be invalid, illegal, or unenforceable, such a provision shall be severed from the License and the other provisions shall remain in full force and effect.

USB DCP Manual.indd iii

Introduction

Features

Mini Data Card Programmer

Garmin Data Cards

The USB Data Card Programmer utilizes Garmin Data Cards. Available in ve sizes: 8 MB Data Card 16 MB Data Card 32 MB Data Card 64 MB Data Card 128 MB Data Card
Check the Garmin web site or see your Garmin dealer for availability of these data cards.

USB Connector

6 Ft. USB Data Cable
Data Card Slot (accepts only Garmin Data Cards)

Data Card Programmer

USB DCP Manual.indd iv

12/18/2002, 4:14:37 PM

Installation of the USB Programmer and Device Drivers
1. Insert either the USB Data Card Programmer CD-ROM, MapSource City Navigator CD-ROM, or MapSource Setup CD into your computers CD-ROM drive. It is important you insert the CD before you plug the USB Programmer into the PC! If the MapSource program is open, close the program. 2. Connect the USB connector on the end of the Programmer cable to the USB port on the back of the computer. Most computers have two USB Ports. Either port should work. The computer does not need to be turned off when connecting or disconnecting the Programmer. After connecting the Programmer to your computer you will need to install the device drivers from the CD-ROM. 3. The computer will recognize the Programmer as a USB (or unknown) device and open the Add New Hardware Wizard and search for the device drivers. Click on Next. If, for some reason, the Wizard does not run automatically, click the Start button and select Settings and then Control Panel. Double click on the Add New Hardware icon. 4. The next screen will ask you if you want it to search for the best driver for your device or if you want to display a list to choose from. Select Search for the best driver for your device and click on Next. 5. The next screen will display a list of locations to search for the new drivers. Select CD-ROM Drive from the list and click on Next. Make certain all other boxes remain unchecked. 6. The Wizard will search for the driver and then display a window to tell you it is ready to install. Click on Next. You may see a Copying Files. screen which tells you the le cannot be found. Choose Root Directory of the CD-ROM drive if not already there, and to try copying again (example d:\). Click OK to continue.

Use care to insert the USB connector correctly. Do not force the connection as this may damage the USB port on your computer or the USB connector on the Programmer.
Installation Connecting the Programmer and Installing the Device Drivers
USB Connector Programmer Cable
USB Port USB (Universal Serial Bus) Port and USB Connector

USB DCP Manual.indd 1

Installation Installing the Device Drivers
7. When installation is complete a window will display that shows the device name (Garmin USB Data Card Programmer) and states the driver installation is nished. Click on Finish. 8. A nal window will appear telling you that operating software for the Card Programmer is being installed. 9. To make sure the USB Programmer has been successfully installed: From the Control Panel, click on System, then the Device Manager tab, then click the + by Universal serial bus controller. You should see Garmin USB Data Card Programmer on the list. Another method would be to open the MapSource program, click the Save To Device icon, then the USB Port tab. You should see Card Programmer listed in the Save Maps To: window.
The required driver les which the USB Data Card Programmer needs to nd on either the USB Data Card Programmer CD, the City Navigator CD, or the MapSource Setup CD are: grmn0200.inf grmn0200.sys grmn1200.sys If these les cannot be seen in the root directory on the CD using Windows Explorer, your View settings may need to be adjusted.
If you see a yellow ! mark in front of the device name, (install) appears at the end of the Programmer name or the Programmer appears under Other Devices as an unknown device, follow these alternate steps to install the Programmer:
1. Double-click the My Computer icon from your Desktop. For Windows 98, click View, Folder Options, then the View tab. For Windows 2000/ME, click Tools, Folder Options, then the View tab. 2. Make note of the following changes if you wish to change your View settings back after installing the Programmer. Change the Hidden Files selection to Show All Files or Show hidden les and folders and uncheck the Hide le extensions for known le types or Hide protected operating system les, then click OK. 3. Be sure the driver CD is inserted and the USB Programmer is plugged into the PC. Open the Control Panel. For Windows 98, click on System, then the Device Manager tab. For Windows 2000/ME, click the Hardware tab, then click Device Manager.

USB DCP Manual.indd 2

12/18/2002, 4:14:38 PM
4. Find and highlight the incorrect Programmer entry on the Device Manager list, click on Remove, then click OK to conrm. 5. Click Refresh, then click Next to begin searching for the drivers. On the next screen, let Windows search by leaving the bullet on the Search for best driver. option and click Next. On the next screen, check ONLY the CD-ROM drive option and click Next. 6. The Wizard will search for the driver and then display a window to tell you it is ready to install. Click on Next. You may see a Copying Files. screen which tells you the le cannot be found. Choose Root Directory of the CD-ROM drive if not already there, and to try copying again (example d:\). Click OK to continue. 7. When installation is complete a window should display that shows the device name (Garmin USB Data Card Programmer) and states the driver installation is nished. Click on Finish. 8. To make sure the USB Programmer has been successfully installed: From the Control Panel, click on System, then the Device Manager tab, then click the + by Universal serial bus controller. You should see Garmin USB Data Card Programmer on the list. Another method would be to open the MapSource program, click the Save To Device icon, then the USB Port tab. You should see Card Programmer listed in the Save Maps To: window.
Windows XP Users: During installation of the USB Data Card Programmer you will see a message stating: The following device has not passed the Windows Logo testing to verify its compatibility with Windows XP. Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future. Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing. Garmin engineers have fully tested this product and it is compatible with Windows XP. Press the Continue Anyways button to nish the installation.
If the installation is still not successful, try shutting the computer off for 1 minute, then trying the alternate steps again. A red X over the Programmer icon in Device Manager normally indicates a defective Programmer. If the USB Programmer still will not install, please contact Garmin Product Support for further assistance.

USB DCP Manual.indd 3

Installation Installing the MapSource Software Upgrade
If you are running an early version of MapSource (prior to 3.04), you may upgrade your version of MapSource at this time using the driver CD provided with the USB Data Card Programmer. If you already have a version of MapSource newer than 3.05 (City Navigator, or the MapSource Setup CD), upgrading from the driver CD is not necessary. You may also visit the Garmin web site to download the most recent upgrade for MapSource.
To Install the MapSource Software Upgrade including USB Data Card Programmer Support:
1. Insert the USB Data Card Programmer CD-ROM into your computers CD-ROM drive. 2. Click the Start button and select Run. 3. Then type in the drive letter of your CD-ROM drive followed by the MapSource Update le name: MSUPDATE.EXE. (For example d:\msupdate.exe) 4. Press ENTER and follow on-screen instructions. 5. Open MapSource and check the About box in the help le to determine that you have successfully installed Version 3.04 or later.

USB DCP Manual.indd 4

12/18/2002, 4:14:39 PM
To Install a Garmin Data Card:
1. Insert the Data Card (Label up and pin connector end rst) into the card slot in the Programmer (standard USB Programmer pictured to the right).
Installation Installing a Data Card in the Programmer
For the Mini-USB Programmer, make sure the Garmin globe logo on the Programmer is facing UP for proper orientation.
2. Be certain to install the Data Card completely into the slot to be sure the pin connections have been made. 3. To remove the Data Card, pull directly away from the Programmer using the extractor handle on the Data Card.

Extractor Handle

Use care not to remove the Data Card from the Programmer until data transfer has been completed to avoid possible loss of data.
Disconnecting the Programmer from Your Computer
After the USB Data Card Programmer has been successfully installed (hardware and software), disconnecting and reconnecting the Programmer can performed without additional installation steps.
1. Before disconnecting the Programmer, be certain that no data transfer is in progress. 2. Unplug the USB connector from your computer. You do not need to turn the computer off before removing or inserting the USB connector.

USB DCP Manual.indd 5

Trouble Shooting

Trouble Shooting Guide

Symptom Probable Cause Remedy
Windows does not recognize that the Programmer has been connected to the computer.

USB Connector is not properly inserted into the USB port on the computer. USB Port on your computer is not properly congured.
Be certain the Programmer has been properly connected to your computer. Consult your computer supplier. Be certain the computer is operating on Windows 98/ME/2000 software. Reconnect the USB Connector to the computer. Install drivers. Insert a Data Card into the Programmer. Push the Data Card fully into the slot in the Programmer. When properly inserted, the card will protrude approximately 1/2 inch from the slot. Insert a different card and try again. Update MapSource software from the Garmin web site.
System operating software is not USB When preparing to transfer data, a No compatible device available. message compatible. appears. Programmer is not connected to USB port. Card Programmer drivers are not installed. When preparing to transfer data, a There No Data Card has been inserted in the is no data card in the Programmer. mes- Programmer. sage appears. The Data Card is not fully inserted into the Programmer.
The Data Card in the Programmer is An unrecognized data card is in the programmer. message appears when you damaged. attempt to transfer data. MapSource must be updated to be compatible with the card.

USB DCP Manual.indd 6

Copyright 2001-2002 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation No 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00201-00 Rev. C

USB DCP Cover.indd 6

12/18/2002, 4:13:29 PM

USB Data Card Programmer

users manual and installation guide
2000 GARMIN Corporation GARMIN International, Inc. 1200 E 151st Street, Olathe, Kansas 66062 U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax. 913/397.8282 GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ U.K. Tel. 44/1794.519944 Fax.44/1794.519222 GARMIN (Asia) Corp. No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax. 886/2.2642.9099 All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without prior written consent of GARMIN Corporation. GARMIN Corporation hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed for personal use, provided that such electronic or printed copy of this manual contains the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual is strictly prohibited. Information in this manual is subject to change without notice. GARMIN Corporation reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes. Visit the GARMIN website for downloadable upgrades to the operating software and the Owners Manual. The website also contains information concerning the use and operation of other GARMIN products. Website address: www.garmin.com GARMIN is a registered trademark, MapSourceTM is a trademark of GARMIN Corporation and may not be used without the express permission of GARMIN Corporation. July 2000 Part Number 190-00201-00 Rev. A Printed in Taiwan

Introduction

Thank you for choosing the GARMIN USB Data Card Programmer. To get successful results from your new programmer, take time to read through this users manual in order to fully understand all of the operating procedures. This manual is organized into three sections: The Introduction section provides licensing agreement information and a description of the programmer. The Installation section introduces you to basic features and procedures for programmer setup. The Trouble Shooting section contains information for finding solutions to installation and operating problems.
Standard Package Contents
Introduction About This Manual
Minimum System Requirements
! USB Data Card Programmer ! CD-ROM with USB Device Drivers for Windows 98 and 2000, and GARMIN MapSourceTM Upgrade Software including USB Support. ! Users Manual ! MapSource Users Manual Addendum for the USB Data Card Programmer
IBM-Compatible PC with Pentium processor, 16 Megabytes RAM, CD-ROM drive, Mouse or other pointing device, 256-color display adapter (24-bit color recommended) and monitor with 640 x 480 resolution or higher, and up to 20 Megabytes free hard drive space. A 32 bit operating system such as Windows 98 or Windows 2000. Universal Serial Bus port (USB). The USB Data Card Programmer is not designed to operate with Windows 95 or Windows NT.

Software Requirements

Existing installation of GARMIN MapSource upgraded to Version 3.04 or later.
Windows 95, Windows NT, Windows 98, and Windows 2000 are registered trademarks of Microsoft Corporation.
Introduction Software License Agreement
THIS SOFTWARE IS OWNED BY GARMIN CORPORATION (GARMIN) AND IS PROTECTED UNDER COPYRIGHT LAWS AND INTERNATIONAL COPYRIGHT TREATIES. THIS SOFTWARE IS LICENSED, NOT SOLD. THIS SOFTWARE IS PROVIDED UNDER THE FOLLOWING LICENSE WHICH DEFINES WHAT YOU MAY DO WITH THE PRODUCT AND CONTAINS LIMITATIONS ON WARRANTIES AND/OR REMEDIES. IMPORTANT: CAREFULLY READ THIS LICENSE BEFORE USING THIS PRODUCT. INSTALLING, COPYING, OR OTHERWISE USING THIS PRODUCT INDICATES YOUR ACKNOWLEDGMENT THAT YOU HAVE READ THIS LICENSE AND AGREE TO ITS TERMS. IF YOU DO NOT AGREE, RETURN THE COMPLETE PRODUCT TO GARMIN INTERNATIONAL, INC. CUSTOMER SERVICE, 1200 EAST 151st STREET, OLATHE, KS 66062 WITHIN 10 DAYS OF THE DATE YOU ACQUIRED IT FOR A FULL REFUND. 1. LICENSE: GARMIN (we or us) provides you with storage media containing computer software (the Program) which may also include digital cartographic data and on-line or electronic documentation, and printed materials together called (the Product) and grants you a limited nonexclusive license to use the Product in accordance with the terms of this license agreement. The copyright and all other rights to the Product shall remain with us. You must reproduce any copyright or other notice marked on the Product on all copies you make. 2. YOU MAY: a) install and use one copy of the Product on a single computer or network. This copy is to be used by only a single user at a time. If you wish to use the Product for more users, you will need an additional license for each user. b) make one copy of the Product for archival or backup purposes. c) use a copy of the Production a home or portable computer if that copy is never loaded at the same time it is loaded on your primary computer. d) transfer the Product to someone else only if you assign all of your rights under this License, cease all use of the Product, erase or destroy any copy (including the hard disk copy) made in support of your use of the Product, and ensure that the other person agrees to the terms of this License. 3. YOU MUST NOT: a) make copies of the Product except as expressly permitted in Section 2 of this License. b) translate, reverse engineer, decompile, or disassemble the Product except to the extent the foregoing restriction is expressly prohibited by applicable law. c) rent, lease, loan, sub-license, distribute, assign, or transfer the Product except as set out in Section 2 (d) above. d) modify the Product or merge all or any part of the Product with another program.

4. TERM: This License shall continue for as long as you use the Product. However, this License will terminate automatically without notice from GARMIN if you fail to comply with any of its terms or conditions. You must agree, upon terminations, to destroy all copies of the Product. The Limitations of Warranties and Liability set out below shall continue in force even after any termination. 5. LIMITATION OF WARRANTIES AND LIABILITY: THE PRODUCT IS PROVIDED ON AN AS IS BASIS WITHOUT ANY WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABLE QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THOSE ARISING BY LAW, STATUTE, USAGE OR TRADE, OR COURSE OF DEALING. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE PRODUCT IS ASSUMED BY YOU. NEITHER WE NOR OUR DEALERS OR SUPPLIERS SHALL HAVE ANY LIABILITY TO YOU OR ANY OTHER PERSON OR, ENTITY FOR ANY INDIRECT, INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, LOSS OF REVENUE OR PROFIT, LOST OR DAMAGED DATA OR OTHER COMMERCIAL OR ECONOMIC LOSS, EVEN IF WE HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR THEY ARE FORESEEABLE. WE ARE ALSO NOT RESPONSIBLE FOR CLAIMS BY A THIRD PARTY. OUR MAXIMUM AGGREGATE LIABILITY SHALL NOT EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. THE LIMITATIONS IN THIS SECTION SHALL APPLY WHETHER OR NOT THE ALLEGED BREACH OR DEFAULT IS A BREACH OF FUNDAMENTAL CONDITION OR TERM OF A FUNDAMENTAL BREACH. SOME STATES/ COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 6. RESTRICTED RIGHTS: If this Product is acquired by or for the U.S. Government, then it is provided with Restricted Rights. Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraphs (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the Commercial Computer Software - Restricted Rights at 48 CFR 52.22719, or clause 18-52-227-86 (d) of the NASA Supplement to the FAR, as applicable. The contractor/manufacturer is GARMIN International, Inc. 1200 E. 151st Street, Olathe, KS 66062, USA. 7.) EXPORT CONTROLS: You agree not to export or re-export the Product to any country in violation of the export control laws of the United States of America. 8. GENERAL: This License is the entire agreement between us, superseding any other agreement or discussions, oral or written, and may not be changed except by a signed agreement. This License shall be governed by and construed in accordance with the laws of the State of Kansas, United States of America. If any provision of this License is declared by a court of competent jurisdiction to be invalid, illegal, or unenforceable, such a provision shall be severed from the License and the other provisions shall remain in full force and effect.

Features

6 Ft. USB Data Cable GARMIN Data Cards

USB Connector

The USB Data Card Programmer utilizes GARMIN Data Cards. Available in five sizes: 8 MB Data Card 16 MB Data Card 32 MB Data Card 64 MB Data Card 128 MB Data Card
Check the GARMIN website or see your GARMIN dealer for availability of these data cards.
Data Card Programmer Data Card Slot (accepts only GARMIN Data Cards)
Installation of the USB Data Card Programmer and Device Drivers
1. Connect the USB connector on the end of the Programmer cable to the USB port on the back of the computer. Most computers have two USB Ports. Either port will work. The computer does not need to be turned off when connecting or dsconnecting the Programmer.
Installation Connecting the Programmer to Your Computer
USB Connector Programmer Cable
Use care to insert the USB connector correctly. Do not force the connection as this may damage the USB port on your computer or the USB connector on the Programmer.
USB Port USB (Universal Serial Bus) Port and USB Connector
After connecting the Programmer to your computer you must install the device drivers from the CD-ROM provided with the Programmer.
2. Insert the Programmer CD-ROM into your computers CD-ROM drive. 3. The computer will recognize the Programmer as a USB device and open the Add New Hardware Wizard and search for the device drivers. Click on Next. If, for some reason, the Wizard does not run automatically, click the Start button and select Settings and then Control Panel. Double click on the Add New Hardware icon. 4. The next screen will ask you if you want it to search for the best driver for your device or if you want to display a list to choose from. Select Search for the best driver for your device and click on Next.
Installing the Device Drivers
Installation Installing the Device Drivers
5. The next screen will display a list of locations to search for the new drivers. Select CD-ROM Device from the list and click on Next. Make certain all other boxes remain unchecked. 6. The Wizard will search for the driver and then display a window to tell you it is ready to install. Click on Next. You may see a Copying Files. screen which tells you the file cannot be found. Choose Root Directory of the CD-ROM drive if not already there, and to try copying again. Click OK to continue. 7. When installation is complete a window will display that shows the device name (GARMIN USB Data Card Programmer) and states the driver installation is finished. Click on Finish. 8. A final window will appear telling you that operating software for the Card Programmer is being installed. Leave the CD-ROM in the CD-ROM drive to complete the MapSource Software Upgrade.

Installing the MapSource Software Upgrade
To Install the MapSource Software Upgrade including USB Data Card Programmer Support :
1. Insert the Programmer CD-ROM into your computers CD-ROM drive. 2. Click the Start button and select Run. 3. Then type in the drive letter of your CD-ROM drive followed by the MapSource Update file name: MSUPDATE.EXE. (For example d:\msupdate.exe) 4. Press ENTER and follow on-screen instructions. 5. Open MapSource and check the About box in the help file to determine that you have successfully installed Version 3.04 or later. 6. Follow instructions contained in the MapSource Addendum provided with the USB Data Card Programmer for transfer of map data to and from Data Cards using the Programmer.
To Install a GARMIN Data Card:
1. Insert the Data Card (Label up and pin connector end first) into the card slot in the Programmer (picture to the right). 2. Be certain to install the Data Card completely into the slot to be certain pin connections have been made. 3. To remove the Data Card, pull directly away from the Programmer using the extractor handle on the Data Card.
Installation Installing a Data Card in the Programmer

Card Slot Data Card

Use care not to remove the Data Card from the Programmer until data transfer has been completed to avoid possible loss of data.

Extractor Handle

Disconnecting the Programmer from Your Computer
After the USB Data Card Programmer has been successfully installed (hardware and software), disconnecting and reconnecting the Programmer can performed without additional installation steps.
1. Before disconnecting the Programmer, be certain that no data transfer is in progress. 2. Unplug the USB connector from your computer. You do not need to turn the computer off before removing or inserting the USB connector.

Trouble Shooting

Trouble Shooting Guide
Symptom Probable Cause Remedy
Windows does not recognize that the Programmer has been connected to the computer.
USB Connector is not properly inserted into the USB port on the computer. USB Port on your computer is not properly configured.
Be certain the Programmer has been properly connected to your computer. Consult your computer supplier. Be certain the computer is operating on Windows 98 or Windows 2000 software.

System operating software is not USB When preparing to transfer data, a No compatible device available. message compatible. appears.
Programmer is not connected to USB port. Reconnect the USB Connector to the computer Card Programmer drivers are not installed. Install drivers. When preparing to transfer data, a There is no data card in the Programmer. message appears. No Data Card has been inserted in the Programmer. Insert a Data Card into the Programmer.
The Data Card is not fully inserted into the Push the Data Card fully into the slot in the Programmer. When properly inserted, Programmer. the card will protrude approximately 1/2 inch from the slot. The Data Card in the Programmer is damaged MapSource must be updated to be compatible with the card. Insert a different card and try again. Update MapSource software from the GARMIN website.
An unrecognized data card is in the progammer. message appears when you attempt to transfer data.
Registration Help us to better support you by completing our on-line registration today! Have the serial number of your USB Data Card Programmer handy and connect to our website (www.garmin.com). Look for the Product Registration link on the Home page. Why should you register your USB Data Card Programmer? Notification of Product Updates Notification of New Products Lost or Stolen unit tracking
NOTE: If you have previously registered your GARMIN product purchase using a mail-in registration card, we invite you to re-register using our NEW on-line system. Many services provided by our new product registration system are now being automated and re-registering your purchase ensures you the best possible support from GARMIN.
Serial Number Use this area to record the serial number (8-digit number located on the bottom of the unit) in case it is lost, stolen, or needs service. Be sure to keep your original sales receipt in a safe place or attach a photocopy inside the manual. Serial Number:
2000 GARMIN Corporation GARMIN International 1200 East 151st Street, Olathe, Kansas 66062, U.S.A GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U.K. GARMIN (Asia) Corporation No 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00201-00 Rev. A