3 Carefully fan the paper to keep the sheets from sticking together. IMPORTANT: Do not load more than 25 sheets of paper. Use the upper limit line inside the paper tray as a guide to prevent overloading. Do not load paper that is missing perforated tabs. To avoid fingerprints, do not touch the glossy side of the paper. 4 Load the paper into the paper tray, with the Kodak logo side facing down. 5 Close the paper tray cover. Purchase Kodak color cartridge & photo paper kits and other accessories at a retailer of Kodak products, or visit www.kodak.com/go/accessories.
Installing the paper tray
1 Open the paper tray door on the photo printer. 2 Slide the paper tray cover back until it clicks into place, about 1.25 in. (3 cm).
3 Slide the paper tray in the printer tray slot until the tray locks into place. IMPORTANT: To ensure the paper tray fits squarely on the photo printer, make sure to keep the paper tray cover all the way open while installing.
Pull the paper tray out to remove it. Close the paper tray cover and paper tray door to keep out dust and debris. When the paper tray is empty, the Paper light glows steady red. After refilling and installing the paper tray, press the Print button to clear the paper error and resume printing.
Printing without a computer
Printing from a card or USB flash drive
You can print pictures directly from your card or USB flash drive.
Middle Slot: SD/MMC (Secure Digital/MultiMedia Card/Reduced Size-MMC) MS (Memory Stick, Memory Stick Duo, Memory Stick Pro, Magic Gate) xD (xD-Picture Card)
Left Slot: CF (CompactFlash Type I, II)
1 Insert a card or plug in a USB flash drive as shown. The current picture appears on the LCD. 2 Create a print order:

Press Press

to locate a picture on the LCD. to choose the number of prints for each picture.
3 When finished choosing prints and print quantities, press the Print button. To exit without printing, press the Cancel button. NOTE: Do not force a card into a slot. Insert only one card into the photo printer at a time. If a card is already inserted but no longer detected, remove and reinsert it. Do not insert or remove a card when the photo printer is transferring pictures.
Purchase cards and other accessories at a retailer of Kodak products, or visit www.kodak.com/go/accessories.
While the printer is printing
When printing, the paper cycles four times. The first three passes apply layers of yellow, magenta, and cyan colors to the print. The fourth pass applies the Kodak XtraLifeTM coating that protects and preserves the image
Removing the perforated tabs from the paper
1 Fold the tabs up, then down. 2 Remove each tab and discard. NOTE: Remove perforated tabs only after printing. Paper missing perforated tabs will not feed properly.

Number and size of prints per sheet One 4 x 6 in. (10.2 x 15.2 cm) picture Up to two 2.1 x 3.3 in. (5.4 x 8.5 cm) pictures Up to four 2 x 3 in. (5.1 x 7.6 cm) pictures Up to nine 1.3 x 2 in. (3.4 x 5.1 cm) pictures
Picture Size setting 1 up (full photo) 2 up (card size) 4 up (wallet size) 9 up (mini photo)
NOTE: To change the default picture size, see page 16.
Effect of picture size on number of copies
In most cases, the picture size setting also determines the number of copies that are printed. For example, if you choose to print a picture with 2 up selected, 2 copies are printed on one sheet of paper. When printing tagged pictures, the number of copies that are printed is determined by the setting on your camera or device. For example, if three pictures on your camera are each tagged for printing one copy, and the 4 up option on the photo printer is selected, three 2 x 3 in. (5.1 x 7.6 cm) pictures are printed on one sheet of paper. For best results, choose a picture size or number of copies (on your printer, camera or device) that minimizes blank space on the paper.
NOTE: When printing from a PictBridge compatible device, picture size and number of copies are determined by the devices multi-up and copies settings. Change these settings on your device before printing. If the picture size option selected on your device does not match any of the picture size options on the photo printer, the closest available picture size option on the photo printer is automatically selected.
Printing different pictures on the same sheet
1 Insert a card in the card slot (or connect a USB device to your photo printer). 2 Choose a picture size:
Press the Menu button. Press to highlight Picture Size (page 12), then press the Print button. Press to choose a picture size, then press the Print button. Press to locate a picture on the LCD.

3 Create a print order:

Press to choose the number of prints for each picture.
4 When finished choosing prints, quantities, and sizes, press the Print button.
To exit without printing, press the Cancel button.
Printing duplicate pictures on the same sheet

Changing the color mode

1 Press the Menu button. 2 Press 3 Press
to highlight Color Mode, then press the Print button. to highlight a choice, then press the Print button.

Natural Enhanced Sepia

Black and White Pictures are printed in the color mode you chose.

Checking the donor level

1 Press the Menu button. 2 Press to highlight Donor Level, then press the Print button. The estimated prints remaining and cartridge size are displayed.

Printing tagged prints

NOTE: This menu choice is available only if pictures have been tagged on your device or card. 1 Press the Menu button. 2 Press to highlight Tagged Prints, then press the Print button.

Transferring pictures from a card slot
1 Make sure Kodak EasyShare software is installed (see page 17) and the photo printer is connected to your computer (see page 19). 2 Insert a card (see page 7.) The current picture is displayed on the LCD. 3 Press the Transfer button on the photo printer. Kodak EasyShare software opens on your computer. 4 Use Kodak EasyShare software to transfer pictures from the card to your computer. See the Kodak EasyShare software Help for details. The Transfer light blinks while the pictures are being transferred. NOTE: With the software installed, connecting the photo printer to the computer establishes a new drive connection for the card slot. Pressing the Transfer button lets you view, copy, delete, and otherwise manage files on the new drive, as you do with other drives on your computer. See your computer documentation for details.
To stop the transfer before it finishes, press the Cancel button. To remove the card, pull it out.
Transferring pictures from a USB device
1 Make sure Kodak EasyShare software is installed (see page 17) and the photo printer is connected to your computer (see page 19). 2 Plug the USB connector from the USB device into the USB connector located on the side of the photo printer. NOTE: If the USB device is already plugged in but no longer recognized, disconnect then reconnect it to re-establish the connection. 3 Press the Transfer button on the photo printer. Kodak EasyShare software opens on your computer. 4 Use Kodak EasyShare software to transfer pictures from the device to your computer. See the Kodak EasyShare software Help for details. The Transfer light blinks while the pictures are being transferred.

Printing from a computer

We recommend using Kodak EasyShare software (included) for printing. This software lets you take advantage of a wide range of features, including editing and printing options, picture organization, and much more. IMPORTANT: Wait until printing is complete before removing paper or the paper tray. Failure to do so can cause paper misfeeds or jams.
Printing with Kodak EasyShare software
1 Make sure Kodak EasyShare software is installed (see page 17) and the photo printer is connected to your computer (see page 19). 2 Click the My Collection tab. 3 Select the pictures you wish to print. 4 Click the Print at Home tab. 5 Make sure the photo printer is selected as the current printer. 6 Change any other settings, such as paper size and print layout, then click Print. NOTE: The Picture Size button on the photo printer is disabled when printing from a computer. Set printing options using EasyShare software. See the EasyShare software Help for details. Printing tagged pictures from your computer 1 Make sure Kodak EasyShare software is installed (see page 17) and the photo printer is connected to your computer (see page 19). 2 Transfer the tagged pictures to your computer (see page 21). 3 Follow steps 4 through 6 above.

Example of an Ad-Hoc network:
Adding your printer to a Wi-Fi wireless network
1 If a USB device is connected to the photo printer, disconnect it. IMPORTANT: Insert card only as shown. Do not force the card into the card slot. 2 Push the Kodak Wi-Fi card into the card slot to seat the connector. The card slot light blinks as the photo printer scans for available networks. Once connected, the card slot light glows steady. NOTE: When properly inserted, the card sticks out slightly, serving as an antenna for receiving Wi-Fi signals. If the Kodak Wi-Fi card is already inserted but the connection is no longer available, remove then reinsert the card to re-establish the connection.
To remove the card, push in and release it. When the card is ejected, pull it out.
3 Make sure the printer driver from the included Kodak EasyShare software CD is installed on your computer. Then connect the printer to your computer with the USB cable (see page 19). 4 Configure the printer Wi-Fi settings (such as SSID and security) and add the printer as a wireless printer on your Wi-Fi wireless network: Windows OSConfigure the printer Wi-Fi settings: a From the Start menu, select Programs (or All Programs). b Open the Kodak folder, then open the EasyShare printer folder. c Select Kodak wireless printer configuration utility. The configuration utility opens on your computer. d Next to Show, select Wi-Fi Primary. e Change settings as necessary to match the settings of your Wi-Fi wireless network. Click Wizard to guide you through the wireless setup process. See the wireless configuration utility Help for details. 30
Add the printer as a wireless printer to your computer: a From the Start menu, select Programs (or All Programs). b Open the Kodak folder, then open the EasyShare printer folder. c Select Kodak wireless printer computer setup assistant. d Click Next. e Select the printer, then click Next. The wireless printer is added to your computer (represented as a wireless copy of your printer in the Windows OS list of printers). Mac OS XAdd the printer to your computer: See Connecting to a computer, page 19. Configure the printer Wi-Fi settings: a Open the finder window, then click the Applications button. (Or open the Applications folder on your operating drive.) b Open the Utilities folder, then double-click Print Setup Utility. c Select the printer from the list, then click Utility. d Change Wi-Fi settings as necessary to match the settings of your Wi-Fi wireless network. See the wireless configuration utility Help for details. 5 Close all programs on your computer, then disconnect the USB cable between the computer and the printer. 6 (Optional) Print a copy of your wireless settings for future reference: At the same time, press and hold the Print button and the Transfer button for 5 seconds.

Print pictures over your Wi-Fi wireless network
1 Add the photo printer to your Wi-Fi wireless network (see page 23). IMPORTANT: Add the printer to the same network as the computer or device you want to print from. If printing from EasyShare software, make sure Enable WIreless Connections is selected in Preferences. (For details, click the Help button in EasyShare software.) 2 On your computer (or your Wi-Fi enabled device), select and print pictures. See your computer or device users guide for details.
Transfer pictures over your Wi-Fi wireless network (EasyShare digital cameras only)
1 Add the photo printer to your Wi-Fi wireless network. IMPORTANT: Add the printer to the same network as the computer or device you want to print from. If you have two or more computers on the same network, use the Kodak wireless printer configuration utility on your computer to choose which computer to transfer to. (For details, see the wireless configuration utility Help.) 2 Connect your EasyShare digital camera to the printer (see page 22), then press the Transfer button. Pictures are transferred to EasyShare software on your computer. NOTE: If the printer is connected to the computer with a USB cable, pictures are transferred using the cable connection, not the wireless connection See your computer or device users guide, or visit www.kodak.com/go/wifisupport and www.wi-fi.org for more information.

Care and maintenance

General care
IMPORTANT: Always disconnect the power before cleaning. Do not use harsh or abrasive cleaners or organic solvents on the photo printer or any of its parts. To clean, wipe the outside of the photo printer and LCD with a clean, dry cloth.
Support the photo printer and tray by placing it on a flat, level surface. Do not block the cooling vents. Avoid blocking the back of the photo printer and paper tray exit. Keep power and USB cables away from the paper path. Keep the surrounding area vacuumed and litter-free. Protect the photo printer from tobacco smoke, dust, sand, and liquid spills.
Avoid placing objects on the photo printer. Keep the photo printer, accessories, and supplies away from direct sunlight and out of high-temperature environments (such as a vehicle parked in the sun). When storing, remove the paper tray, then close the paper tray cover (see page 6) and paper tray door to keep out dust and debris. Store paper flat.
Cleaning the paper feed roller
To prevent misfeeds and to make sure your pictures look their best, we recommend that you keep the paper feed roller clean. Inspect the roller weekly for debris particles, and clean if necessary. IMPORTANT: Unplug the power before cleaning the paper feed roller. 1 Unplug the AC power cord from the power outlet. 2 Remove the paper tray from the photo printer, and leave the paper tray door open. 3 Lightly moisten a lint-free cloth with water. IMPORTANT: Do not use cotton or cotton swabs to clean the paper feed roller. 4 Use the moistened cloth to gently wipe clean the surface of the paper feed roller. Advance the feed roller with your thumb as necessary, and continue cleaning. 5 Allow the paper feed roller to fully dry before reconnecting the power.

4 Re-install the paper tray, then press to resume printing. IMPORTANT: Use only Kodak color cartridge & photo paper kits for your photo printer. Do not use inkjet paper.
IMPORTANT: Always check the paper slot on the back of the photo printer for jammed paper. 3 Remove the paper supply from the paper tray. Carefully fan the
paper to keep the sheets from sticking together.
4 Reload the paper tray. Do not exceed the fill line. 5 Re-install the paper tray, then press
If the Color Cartridge light is blinking quickly, check the color cartridge.
IMPORTANT: The color cartridge may lock in place if there is a paper error. Do not attempt to remove the cartridge without first clearing the paper error. Make sure the Paper light is off before attempting to remove the cartridge (see Paper light under Status lights, page 43).
Remove the color cartridge, remove any slack from the ribbon, then re-install the cartridge (page 3). Press to resume printing.

If. Try the following

Printing stops IMPORTANT: Use only Kodak color cartridge & photo paper kits for your photo printer. Do not use inkjet paper. during mid-print (paper stops Check the paper: feeding, and 1 Remove the paper tray (page 6). Paper light may blink) 2 Check the paper slot on the back of the photo printer.
3 Remove loose paper from the photo printer. If paper is jammed, see

page 37.

4 Inspect the paper supply: make sure removable tabs have not been
detached from the paper. Reload with new paper if necessary.
5 Carefully fan the paper to keep the sheets from sticking together. 6 Reload the paper tray. Do not exceed the fill line. 7 Re-install the paper tray, then press
Print is smudged Fingerprints may be on glossy side of paper. Handle paper by the edges or by the removable tabs (page 4). Print is spotted Check to see if the paper is dirty, and use a dry, lint-free cloth to wipe clean. For excessive dirt or debris, thoroughly clean the paper tray, and load new paper (page 5). Check and clean the paper feed roller if necessary (page 34).
NOTE: When storing paper, remove and close the paper tray and paper tray door to keep dust and debris from collecting on the paper or inside the photo printer (page 4).
Print is too light IMPORTANT: Use only Kodak color cartridge & photo paper kits for
your photo printer. Do not use inkjet paper.
Make sure the paper is loaded with the Kodak logo facing down. Reload
if necessary (page 5). Try re-taking the picture with the flash off. See your camera users guide for details. Adjust the exposure compensation on your camera, and try re-taking the picture. See your camera users guide for details. Edit the picture using Kodak EasyShare software on your computer. See the EasyShare software Help for details. Print is too dark Try re-taking the picture with the flash on, or move within the flash range of the camera. See your camera users guide for details. or is discolored Adjust the exposure compensation on your camera, and try re-taking the picture. See your camera users guide for details. Edit the picture using Kodak EasyShare software on your computer. See the EasyShare software Help for details. Make sure the photo printer is not placed in direct sunlight or is not operating in a high-temperature environment. Make sure the cooling vents are not blocked or dirty (page 1). Pictures are cropped

Change the picture quality setting (or resolution) on your digital camera
to 3:2. See your camera users guide for details. Adjust cropped pictures using Kodak EasyShare software on your computer. If you are printing from an application on your computer, select the proper paper size in print options.
NOTE: Cropping may vary depending on the selected picture size (page 12).
A selected The image file may be corrupt. Review the picture on the camera or computer and delete if necessary. picture does not print. The image file may not be JPEG format. The photo printer can only print JPEG files in standalone mode. Connect to a computer (page 19) and use EasyShare software to print BMP and TIFF formats.
If. Nothing happens when you try to print Try the following
Check the power connections (page 2). Remove the paper tray, check that paper is properly loaded, and re-install

(page 6).

If the Paper light glows steady red, load paper (page 5). Make sure the color cartridge is properly installed (page 3). If the Color
Cartridge light is on, install a new cartridge.
If printing from a USB device, make sure the device is turned on (if
applicable). Nothing Check the USB connections from the PictBridge compatible device to the photo printer (page 8). happens when you try to print Re-establish the connection: disconnect, then reconnect the USB cable from the PictBridge compatible device to the photo printer. (from PictBridge compatible Make sure there is at least one picture in the PictBridge compatible device) devices internal memory or memory card.
Check the USB connections from the photo printer to the computer Nothing (page 19). happens when you try to print The computer may be transferring pictures. Wait a few seconds, then try again. (from computer) Access the printer menu for your system. Remove check marks next to Pause Printing and Offline, if checked. Close unnecessary software applications. Disconnect then reconnect the USB cable from the photo printer to the computer (page 19). Make sure Kodak EasyShare software is installed (page 17). Install if necessary. If you choose Custom installation, make sure to install the printer driver. Uninstall, then reinstall Kodak EasyShare software (page 17). Make sure your computer meets the minimum system requirements. Upgrade your system if necessary.
Printing is slow NOTE: When printing a large number of prints, printing may slow down to prevent the
print head from overheating. Turning on the red-eye reduction feature may result in longer printing times.
Make sure the photo printer is not placed in direct sunlight or is not
operating in a high-temperature environment.
Make sure the cooling vents are not blocked or dirty (page 1). Close unnecessary software applications. Make sure your computer meets the minimum system requirements.

Upgrade your system if necessary.
IMPORTANT: The color cartridge may lock in place if there is a paper Unable to error. Do not attempt to remove the cartridge without remove color cartridge (paper first clearing the paper error. Make sure the Paper light is light may glow off before attempting to remove the cartridge (see Paper steady amber or light under Status lights, page 43). blink) Check to see if the paper tray is empty or if paper is missing perforated tabs. Reload paper if necessary (page 5), then try again. Make sure paper is not jammed. Clear the jam if necessary (page 37), then try again. Disconnect then reconnect the power and try again. IMPORTANT: Upon reconnecting the power, the color cartridge may advance to the next picture slot on the ribbon, resulting in a supply mismatch (see below).
Paper runs out Supply mismatch can result from several different situations, including: before the color Scrapping of paper due to jams or other errors cartridge (or Gradual advancement of the color cartridge ribbon due to removing vice versa) ribbon slack or clearing jams Advancement of the color cartridge ribbon upon reconnecting power to unlock the color cartridge Supply mismatch is likely to occur as you continue to use your photo printer. To keep your cartridge and paper supply synchronized, discard unused cartridge or paper when one or the other is fully depleted.
If. Nothing happens when you try to print from a Bluetooth technology enabled device Try the following
The internal Bluetooth radio is off. Press the Bluetooth button, then try

again.

Move within range of the Bluetooth radio signal (30 ft, or 10 m). The device does not find the printer. On the device, turn wireless
technology on, then repeat the discovery process.
The device does not use an OPP or FTP profile.
Transfer/communication problems
If. Try one or more of the following , on the photo printer. Nothing happens Press the Transfer button, when you try to Check the power and USB connections from the photo printer to the transfer pictures to computer (page 19). the computer Check USB connections between the photo printer and the USB device. Close unnecessary software applications, and minimize remaining application windows. Follow any messages on the screen that may have been hidden by other windows. Disconnect then reconnect the USB cable from the photo printer to the computer (page 19). Make sure Kodak EasyShare software is installed (page 17). Install if necessary. If you choose Custom installation, make sure to install the printer driver. Uninstall, then reinstall Kodak EasyShare software (page 17). Make sure your computer meets the minimum system requirements. Upgrade your system if necessary.
Wireless network connection
Problem Cause and/or solution Photo printer cannot A Kodak Wi-Fi card is not inserted or is not fully inserted. Reinsert the Wi-Fi card (page 29). connect to the network Check the power connections. Make sure the wireless router and network are running before the photo printer begins scanning for a network. Out of range of the Wi-Fi signal. Make sure the photo printer is located within the operating range of the Wi-Fi wireless network. The photo printer network settings are incorrect. Using the Wi-Fi wireless configuration utility on your computer, change the settings to match those of the network. See the Wi-Fi wireless configuration utility Help for details. There is interference in the wireless signal (such as a microwave oven). Wait until there is no interference, then try again.

Status lights

Print button/light Light status Light glows steady green Light blinks green Cause The photo printer is ready for printing. The photo printer is printing. Action/solution None required.
Print button/light Light status Light is off Cause There are no pictures in the camera or on the card. The compatible device is not connected. Action/solution None required. To enable Print: 1 Take pictures.

2 Connect the camera or

compatible USB device (page 8).
The camera or USB device is None required. transferring pictures to the When transfer is complete, press computer, or has established an the blinking Transfer button,. active connection to the computer. A PictBridge compatible device is None required. connected. The Print button is disabled; print command is controlled from the PictBridge compatible device. To print from another source, unplug the PictBridge compatible device. Color Cartridge light Light status Cause Action/solution
IMPORTANT: The color cartridge may lock in place if there is a paper error. Do not attempt to remove the cartridge without first clearing the paper error. Make sure the Paper light is off before attempting to remove the cartridge (see Paper light).
Light is off The color cartridge is properly installed and is working normally. None required.
Color Cartridge light Light status Light slowly blinks amber for several seconds Cause The color cartridge is nearly depleted. Action/solution None required.
Light blinks red There is a color cartridge jam. Light glows steady red The color cartridge is depleted. The color cartridge is not installed or is not fully seated. Paper light Light status Cause
Clear the jam (page 37), then press. Install a new color cartridge (page 3), then press. Remove and re-install the color cartridge (page 3), then press.

Action/solution

IMPORTANT: The color cartridge may lock in place if there is a paper error. Do not attempt to remove the cartridge without first clearing the paper error. Make sure the Paper light is off before attempting to remove the cartridge.
Light is off The paper tray is properly installed and has an ample supply of paper. None required. Clear the jam (page 37), then press. Remove loose paper. Check the paper supply. Reload with new paper if necessary, then press.
Light blinks red There is a paper jam. Printing stopped during mid-print; the paper may be damaged or is missing removable tabs (page 38).
Paper light Light status Light glows steady red Cause The paper tray is empty. The paper tray is not installed or is improperly installed. Action/solution Load paper (page 5), then press Remove the paper tray, check that paper is properly loaded, and re-install (page 6). Press to resume printing.

Helpful links

Photo printer Get support for your product (FAQs, troubleshooting information, etc.) Purchase full range of digital camera and printer accessories. Download latest photo printer software, firmware and drivers See online tutorials Software Get information on EasyShare software Get help with the Windows operating system and working with digital pictures www.kodak.com/go/printerdocks
www.kodak.com/go/accessories www.kodak.com/go/printerdockdownloads www.kodak.com/go/howto www.kodak.com/go/easysharesw (or click the Help button in the EasyShare software) www.kodak.com/go/pcbasics
Other Get support for Kodak printers, cameras, software, accessories, more Get information on Kodak EasyShare photo printers Get information on Kodak inkjet products Optimize your printer for truer, more vibrant colors Register your photo printer www.kodak.com/go/support
www.kodak.com/go/printerdocks www.kodak.com/go/inkjet www.kodak.com/go/onetouch www.kodak.com/go/register
Telephone customer support
If you have questions concerning the operation of the software or printer, you may speak with a customer support representative. Have this information available: Computer model, operating system Printer serial number
Processor type and speed (MHz) Amount of memory (MB) and free hard disk space
Greece Hong Kong India Italy Korea
Version of Kodak EasyShare software Exact error message you received

243 0270

Australia 701 Austria Belgium Brazil Canada China 820 6027
40775 Singapore 9002 Spain Sweden Switzerland Taiwan

0024 Thailand Turkey UK

Denmark Indonesia Ireland Finland 1 17056
Netherlands 9372 New Zealand Norway 33
US (toll-free) / (toll) / 6231
Philippines / 9600 International +458 / Toll Line 6714 Metro Manila 1625 International +458 Toll Fax 415 4125

France

Poland

Germany 0035 Portugal

Visit www.kodak.com/go/dfiswwcontacts.

Appendix

Photo printer specifications
For more specifications, visit www.kodak.com/go/printerdocks.
Photo printer specifications Printing process Operating environment (for optimum picture quality) Power (via AC power adapter) Thermal dye transfer Temperature: 50 to 95 F (10 to 35 C) Humidity: 10% to 86% RH Output: 24 V DC Input: 100 V to 120 V AC @ 50/60 Hz, via AC power adapter (US and Canada only) 100 V to 240 V AC @ 50/60 Hz, via AC power adapter (all other countries) Consumption while printing: 60 watts maximum Approximately 75 seconds for first 4 x 6 in. (10.2 x 15.2 cm) print, then 60 seconds. NOTE: Printer may slow down when thermal head needs to cool. Print speed is dependent on picture size, number of continuous prints, and environmental conditions. Color, black & white, sepia Without paper tray: 5.28 x 7.40 x 3.27 in. (13.4 x 18.8 x 8.3 cm) With paper tray: 12.17 x 7.40 x 3.27 in. (30.9 x 18.8 x 8.3 cm) Weight Print size 52 Without paper tray: 33.5 oz (950 g) With paper tray: 38.4 oz (1090 g) 4 x 6 in. (10.2 x 15.2 cm)

Print speed

Print options Size
Photo printer specifications Paper size with perforated tabs Picture resolution LCD 4 x 7.25 in. (10.2 x 18.4 cm) 300 ppi, continuous tone 3.5 in. (8.9 cm); TBD dpi
Compatible input devices Memory card slots: CompactFlash Type I, Secure Digital/MultiMedia Card/Reduced Size-MMC, Memory Stick (Memory Stick Duo, Memory Stick Pro, Magic Gate), xD-Picture Card. USB port: USB flash drive (USB key), Pictbridge compatible camera, Bluetooth device supporting OBEX OPP. Wireless capability Bluetooth (built-in); Wi-Fi (when used with optional Kodak Wi-Fi card and Wi-Fi enabled computer).

Wireless channels

This product operates on the legal channel for your region. You are not able to manually select the channel. Wi-Fi networks operate in the ISM (Industrial, Scientific, and Medical) radio frequency band. The ISM band is divided into channels, each occupying 5 MHz of frequency band. To join a wireless network, a node must set its channel to that of the wireless router (or - in a device-to-device network - to that of the first node). Nearby networks that operate on the same channel will interfere with one another, resulting in lower network speed or connection loss. CAUTION: The Wi-Fi card for this device transmits at 15 dBm. In France, the power level is limited to 10 dBm in outdoor environments, per regulations. When in France, use the wireless functions of this product indoors only.
Important safety instructions

Using this product

Read and follow these instructions before using Kodak products. Always follow basic safety procedures. Use only a USB-certified computer. Contact your computer manufacturer if you have questions. The use of an accessory attachment that is not recommended by Kodak, such as an AC adapter, may cause fire, electric shock, or injury. CAUTION: Do not disassemble this product; there are no user-serviceable parts inside. Refer servicing to qualified service personnel. Do not expose this product to liquid, moisture, or extreme temperatures. Kodak AC adapters and battery chargers are intended for indoor use only. The use of controls, adjustments, or procedures other than those specified herein may result in exposure to shock and/or electrical or mechanical hazards.
Upgrading your software and firmware
Download the latest versions of the software included on the Kodak EasyShare software CD and the photo printer firmware (the software that runs on the photo printer). Visit www.kodak.com/go/printerdockdownloads.
Additional care and maintenance
Do not allow chemicals, such as suntan lotion, to come into contact with the painted surface of the photo printer. If the photo printer has been subjected to inclement weather or you suspect water has gotten inside the photo printer, turn off the photo printer and remove the paper tray and color cartridge. Allow all components to air-dry for at least 24 hours before using the photo printer again. If this does not resolve the problem, contact customer support (see page 51). Connect a tripod directly to the camera; do not connect a tripod to the printer. Service agreements are available in some countries. Contact a dealer of Kodak products for more information. The photo printer and the AC power adapter contain a small amount of lead in the circuit board. Disposal of this material may be regulated due to environmental considerations. Disposal of the color cartridge is not regulated and should not be subject to state or local landfill, incineration, or recycling requirements. For more disposal or recycling information, contact your local authorities. In the US, visit the Electronics Industry Alliance Web site at www.eiae.org.

Warranty

Limited warranty
Kodak warrants this product to be free from malfunctions and defects in both materials and workmanship for one year from the date of purchase. Retain the original dated sales receipt. Proof of the date of purchase will be required with any request for warranty repair.
Limited warranty coverage
This limited warranty will be honored only within the geographical location that Kodak EasyShare digital cameras and accessories were purchased. Kodak will REPAIR or REPLACE Kodak EasyShare digital cameras and accessories if they fail to function properly during the warranty period, subject to any conditions and/or limitations stated herein. Such repair service will include all labor as well as any necessary adjustments and/or replacement parts. Such repair or replacement is the sole remedy under this warranty. If replacement parts are used in making repairs, these parts may be remanufactured, or may contain remanufactured materials. If it is necessary to replace the entire product, it may be replaced with a remanufactured product.

Limitations

Request for Warranty service will not be accepted without proof of date of purchase, such as a copy of the original dated Kodak EasyShare digital camera or accessory sales receipt. (Always keep the original for your records.) This warranty does not apply to the battery(s) used in digital cameras or accessories. This warranty does not cover circumstances beyond Kodaks control, nor problems caused by failure to follow the operating instructions in the Kodak EasyShare digital cameras and accessories users guides. This warranty does not apply when failure is due to shipping damage, accident, alteration, modification, unauthorized service, misuse, abuse, use with incompatible accessories or attachments, failure to follow Kodaks operation, maintenance or repacking instructions, failure to use items supplied by Kodak (such as adapters and cables), or claims made after the duration of this warranty. Kodak makes no other express or implied warranty for this product. In the event that the exclusion of any implied warranty is ineffective under the law, the duration of the implied warranty will be one year from the purchase date. 56
The option of replacement is Kodaks only obligation. Kodak will not be responsible for any special, consequential or incidental damages resulting from the sale, purchase, or use of this product, regardless of the cause. Liability for any special, consequential or incidental damages (including but not limited to loss of revenue or profit, downtime costs, loss of the use of the equipment, cost of substitute equipment, facilities or services, or claims of your customers for such damages resulting from the purchase, use or failure of the product), regardless of cause or for breach of any written or implied warranty is expressly disclaimed and excluded herefrom.

A AC power adapter & cord, connecting, 2 accessories & supplies, ordering, 49 B Bluetooth button, i, 27, 46, 49 button Bluetooth, i, 27 cancel, i, 7 crop, i menu, i power, i print, i, 7 red-eye reduction, i rotate, i slideshow, i transfer, i, 21, 29 C cable AC power adapter & cord, 2 USB, 8, 19, 22 Canadian DOC statement, 59 cancel button, i, 7 card slot, i card reader printing, 7 slot, 7 transferring pictures, 21 troubleshooting, 48 care & maintenance
general, 33, 55 handling, storing cartridge, 2 handling, storing paper, 4 paper feed roller, 34 traveling with photo printer, 35 cartridge. See color cartridge CE, 59 channels, wireless regulations, 53 Class B ITE, 60 color cartridge door, ii, 3 handling, storing, 2 installing, removing, 3 light, i, 44 color, automatic correction, 24 computer connecting photo printer, 19 installing software, 17 printing from, 23 transferring pictures to, 21, 22 uninstalling software, 18 connecting PictBridge compatible device, 8 power, 2 connector power (DC-in), ii, 2 USB (from device), 8 USB (to computer), ii, 19 cooling vents, ii copies, selecting number of, 9, 12 crop button, i customer support, 51 61
D DC-in, power connector, ii, 2 disposal and recycling of printer, 55 door cartridge, ii, 3 paper tray, i, 6 F FCC and Industry Canada, 59 compliance and advisory, 57 firmware, upgrading, 49, 54 H help software, 49 telephone support, 51 troubleshooting, 36 Web links, 49 I installing paper tray, 6 software, 17 K Kodak EasyShare software help, 49 installing, 17 printing with, 23 uninstalling, 18 Kodak Web sites, 49 Kodak Wi-Fi card. See wireless 62
L layout. See picture size LCD, i light Bluetooth, i, 27, 46, 49 cancel, i card reader, 48 color cartridge, i, 44 menu, i paper, i, 45 power, i print, i, 43, 46 red-eye reduction, i, 49 status, 43 transfer, i, 29 USB device connector, 47 M Macintosh OS installing software on, 17 uninstalling software, 18 maintenance general, 33, 55 handling, storing cartridge, 2 handling, storing paper, 4 paper feed roller, 34 menu button, i multi-up. See picture size N network. See wireless P paper feed roller, cleaning, 34
handling, storing, 4, 8 light, i, 45 loading, 5 removing perforated tabs, 8 slot, ii paper tray, i door, i installing, removing, 6 PictBridge compatible device, printing from, 8 picture size and number of copies, 12 changing default, 12 printing different pictures on same sheet, 13 printing different sizes/layouts, 12 printing duplicate pictures on same sheet, 14 pictures automatic color correction of, 24 printing different pictures on same sheet, 13 printing duplicate pictures on same sheet, 14 printing from card reader, 7 printing from PictBridge compatible device, 8 printing tagged, 9 selecting number of copies, 9, 12 tagging for automatic printing, 9 transferring from card reader, 21 transferring. See transferring pictures power

photo printer

Enhance and edit pictures

Wireless printing

Kodak Perfect Touch technology for better, brighter pictures and red-eye reduction

Waterproof prints

Print with or without a computer
Get real Kodak pictures from virtually any digital camera.
With the Kodak EasyShare photo printer 500, its one-touch simple to print real Kodak pictures from popular memory cards and PictBridge enabled digital cameras. Edit and view your pictures before you print. Its simple on the 8.9 cm (3.5") display the worlds largest*. The photo printer 500 also features Kodak Perfect Touch technology for better, brighter pictures. Other snapshot photo printers make digital prints. The Kodak EasyShare photo printer 500 makes real Kodak pictures.
View and edit pictures on the worlds largest LCD display at 8.9 cm (3.5")* Print from your memory card or directly from your PictBridge enabled digital camera Print real Kodak pictures in 60 seconds with or without a computer Automatically get better, brighter pictures time after time with Kodak Perfect Touch technology Reduces red eye at the touch of a button its that simple Kodak Xtralife lamination provides the protection your pictures need to be durable, waterproof and to last a lifetime** Print wirelessly from your Bluetooth wireless technology enabled cell phone, PDA, or other devices Wi-Fi ready wirelessly connect to your computer and print from anywhere in your home with optional Kodak Wi-Fi card Select from 4 print sizes up to 10 x 15 cm (4" x 6"), and choose from 4 color modes (natural, enhanced, sepia, and black and white) Print directly from PictBridge enabled digital cameras

Before After

Kodak Perfect Touch technology automatically delivers better, brighter pictures and reduces red eye with the touch of a button.
Workswith: Works with: COMPACTFLASH Cards CompactFlash cards SD/MMC Cards SD/MMC cards Memory Sticks Memory sticks xD-Picture Card PictBridge enabled device xD-Picture Cards Bluetooth wireless PictBridgeenabled device technology enabled devices Wi-Fi (accessory required) Bluetooth wireless technology USB flash drive enabled devices Wi-Fi enabled devices (accessory required) USB flash drives Kodak Perfect Touch technology for better, brighter pictures time after time
Worlds largest LCD display*
Zoom, crop, and enhance your photos right from the printer
Reduce red eye at the touch of a button

One-touch printing

Includes Kodak EasyShare software to organize, print, and share your digital pictures Includes Kodak color cartridge and photo paper kit
Create durable, waterproof pictures that last a lifetime**
Printing Pictures per sheet/ print sizes
Media size Print technology Print speed Color modes Power Power
One 102 x152 mm (4" x 6") Two 75x102 mm (3" x 4") with borders Four 51x 75 mm (2"x 3") Nine 34 x 51 mm (1.3"x 2") 102 x184 mm (4"x 7"), including two 16 mm (0.6") perforated sections (one on each end) Continuous-tone thermal dye transfer 60 sec. from computer, 65 sec. from camera/card Natural, enhanced, sepia, black and white 24V AC adapter (100-240 VAC 50/60 Hz)
Stand-alone functionality Reads CompactFlash cards, SD/MMC cards, xD-Picture Cards, memory sticks, USB flash drives, camera and cell phone cameras or devices PictBridge compatible Editing picture size, crop, red-eye reduction Wireless compatibility Built-in Bluetooth wireless technology (OPP and FTP) Wi-Fi ready (optional Kodak Wi-Fi card required) Package contents Kodak EasyShare photo printer 500 and paper tray Kodak color cartridge and photo paper sample pack (10 sheets) 24V AC adapter USB cable Kodak EasyShare software with printer driver Welcome kit Ordering information Kodak EasyShare photo printer 500 and paper tray (U.S. and Canada).xxx xxxx Accessories Kodak Wi-Fi card.xxx xxxx Kodak printer dock travel bag.xxx xxxx Kodak color cartridge & photo paper kit.xxx xxxx Kodak USB cable.xxx xxxx
* In the snapshot photo printer category ** Under typical home display conditions *** Optional Wi-Fi accessory card required Actual print speed may vary
System requirements WINDOWS: Windows 98, 98SE, 2000, ME, or XP OS 233 MHz processor or greater 64 MB RAM available (128 MB RAM for Windows XP OS) 200 MB hard disk space available CD-ROM drive USB connectivity MACINTOSH: PowerPC-based Macintosh computer Macintosh OS 10.2 or higher 128 MB RAM available 200 MB hard disk space available CD-ROM drive USB connectivity Other specifications Print resolution File formats LCD Tray capacity Weight Dimensions PictBridge compatible Warranty 300x300 ppi continuous tone thermal dye transfer JPEG 8.9 cm (3.5") diagonal adjustable color image display tray 25, output 25 1,262 grams (44.5 oz.) 33.4x7.8x18.6 cm (13.1"x3.1"x7.3") One year

For more information on the Kodak EasyShare photo printer 500, visit www.kodak.com/go/easyshare
Eastman Kodak Company, 2005. Kodak, EasyShare, Perfect Touch, are trademarks of Eastman Kodak Company. PictBridge is a trademark. Eastman Kodak Company is an authorized licensee of the CompactFlash trademark. Wi-Fi is a registered trademark of the Wi-Fi Alliance. The Bluetooth trademark is owned by the Bluetooth SIG, Inc. Product specifications subject to change without prior notice. Simulated images. IC-xxxx CAT No. xxx xxxx