FS3830NIG.book

FS-3820N FS-3830N

Page Printers

Installation Guide

FS3830NIGTOC.fm

Caution
No liability is assumed for any damage caused by improper installation.

Notice on Software

Software used with this printer must support the printers emulation mode. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures described in the Operation Guide contained as an electronic file in the CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printers firmware (contents of its read-only memory). This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done.

Table of Contents

STEP 1 Unpacking... 1 STEP 2 Positioning the Printer... 2 STEP 3 Installing the Toner Container... 3 STEP 4 Installing the Waste Toner Box.. 5 STEP 5 Connecting the Printer to the Computer. 7 STEP 6 Connecting the Power Cord.. 9 STEP 7 Adding Paper to the Paper Cassette and MP Tray. 10 STEP 8 Turning the Power Switch On.. 18 STEP 9 Printing a Status Page.. 19
2003, 2004 by KYOCERA MITA CORPORATION All rights reserved. Revision 1.1 January 2004

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is missing against the list of shipped components below.
List of Shipped Components
(A) (B) (C) (D) (E) Printer (F) (for U.S.A. only)
Printer Waste Toner Box (E) CD-ROMs (B)
Installation Guide [this booklet] and other printed matter (B) Toner Container (D) Power Cord (F) Dust Cover (C) [for U.S.A. only] Plastic Bag for Developer Unit (A)

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

30 cm (11-13/16 inches) 20 cm (7-7/8 inches) [40 cm (15-3/4 inches) when the option rear tray is installed]

30 cm (11-13/16 inches)

60 cm (23-5/8 inches)

25 cm (9-7/8 inches)

Be sure to secure enough space around the printer. Prolonged use without sufficient clearance may cause heat to build up within the printer, resulting in fire.

Environment

Temperature Humidity
10 to 32.5 C (50 to 90.5 F), ideally about 23 C (73.4 F) 20 to 80 %, ideally 60 %
Do not install the printer where temperature or humidity is outside the recommended range. Print quality may suffer and there will be an increased chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to: Direct drafts of hot or cold air Direct drafts from outside (Avoid locations near building entrances.) Sudden temperature or humidity changes Sources of high temperature, for example, near stoves or radiators Excessive dust Vibration Unstable surfaces and surfaces that are not level Ammonia or other harmful fumes (If you are planning to fumigate the room, or make liberal use of insecticide, remove the printer first!) Excessive sunlight or humidity Lack of ventilation Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above sea level
Installing the Toner Container
Before you can use the printer for the first time, you must prepare it by installing the toner container, waste toner box, and set up the interfacing with the computer.

Paper source

Paper cassette MP tray

Paper weight

60 to 105 g/m 60 to 200 g/m
The edges of paper are sharp. When loading paper, be careful not to cut your hand on the paper.

Paper cassette

Standard paper sizes are attached to the inside of the paper cassette as shown in the following figure. Align the paper guides and paper stopper to the paper size you want to print on as described on the next page.

A4 Letter B5 A5

1 Pull the paper cassette all the way out of

the printer.

Paper Cassette
2 Push the bottom plate down until it

locks.

Bottom Plate
Standard paper sizes are attached to the inside of the paper cassette as shown in the following figure. In the paper cassette for U.S.A., Legal size indication is also attached.
3 Turn the paper size dial so that the size
of the paper you are going to use appears in the paper size window.
When the paper size dial is set to OTHER the paper size must be set into the printer on the operator panel. See the Operation Guide (PDF file) provided on the CD-ROM.
Paper Size Dial Paper Size Window
4 Adjust the position of the paper guides
located on the left and right sides of the paper cassette. Pull the release lever on the left side guide and slide to the desired paper size.

Release Paper Guides

5 Adjust the position of the paper stopper

Release

located at the rear of the paper cassette. Pull the release lever and slide the paper stopper to the desired paper size. When shipped from the factory, the paper cassette is set to A4 size. When using other size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the paper guides and paper stopper to the size of the paper. Adjust them so that they are in light contact with the paper.

Paper Stopper

Fan the media (paper/transparencies), then tap it on a level surface to avoid media jams or skewed printing.
6 Slide the paper into the paper cassette.

Load Limit

Do not load more paper than will fit under the load limits on the paper guides. The paper cassette will hold approximately 500 sheets of paper with a 80 g/m (21 lb.) basis weight, or with a thickness of 0.11 mm.

7 Set the stack of paper so that it is under

the clips as shown.

8 Insert the paper cassette into the slot in
the printer. Push it straight in as far as it will go.

Paper Gauge

There is a paper gauge on the right side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to the level of (empty).
9 If you have installed a paper cassette
that can hold the Legal size paper, install the dust cover at the back of the printer. (The Legal size cassette and the dust cover are supplied for U.S.A. only.)

Removing the Dust Cover

MP (Multi Purpose) tray
1 Pull the MP tray towards you until it

stops.

MP Tray

2 Pull out the subtray.

3 Adjust the position of the paper guides

A4 LTR

on the MP tray. Standard paper sizes are attached to the MP tray. For standard paper sizes, slide the guides to the position marked correspondingly.

Paper Guides

4 Align the paper with the paper guides
and insert as far as it will go.
Do not load more paper than will fit under the load limits on the inside of the MP tray.
If the paper is considerably curled in one direction, for example, if the paper is already printed on one side, try to roll the paper in the opposite direction to counteract the curl. Printed sheets will then come out flat.

Correct

Incorrect

To Close the MP Tray

Before closing the MP Tray, ensure the subtray is pushed back in, and the paper guides are opened as far as they will go.

Envelopes

Envelopes should be fed in the face-up position, right edge first.
Test a sample envelope on the printer and check that printing quality is satisfactory before purchasing. To avoid trouble, we recommend that envelopes be delivered face-up using the option rear tray. Refer to next page.
Some types of envelopes are not suitable for printing. For details on suitable types of envelopes, see the Operation Guide contained as a PDF file in the CDROM supplied with the printer.
Installing the Option Rear Tray
Use the rear tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, transparencies, or thick paper. This rear tray is a separate option.

Legal Size A4 Size Letter Size

Rear Tray

Turning the Power Switch On
This section describes the procedure for turning on the printers power. During start-up, the language for the message display and status page of this printer can be selected from English, French, German, Italian, Dutch, Spanish, and Portuguese. The default message language is English. For how to change the message language to another, refer to the Selecting a Message Language section.
1 Switch on the printers power. The message display should indicate Self test.
If the indicator does not light, check that previous steps were performed properly.

Power Switch

When the printer is first switched on after installation, there will be a delay of approximately 8 minutes before the printer gets ready to print as the developer unit needs to be filled with toner. During this period, the message display shows Please wait (Adding toner).

Ready --- A4 PLAIN

2 Wait until the READY (
) indicator is also lit and the message display indicates Ready. The printer is ready to print.
Selecting a Message Language
The default message language is English. To change the message language to another, follow the procedure described below. If required, your dealer can download major languages other than English, French, German, Italian, Dutch, Spanish, and Portuguese to your printer. Please contact your dealer.
1 While pressing the ENTER key, turn the

CANCEL

power switch ON ( l ). Keep pressing the ENTER key until the message display indicates Please wait (approximately 1 minute). The message display should indicate Self test. Please wait, release the ENTER key.

Please wait

2 When the message display shows

MSG language ? English

3 The message display indication
changes to that shown on the left and ? flashes.

4 Press the

or key repeatedly until the message display shows the desired language and then press the ENTER key. If you do not wish to change the setting, press the CANCEL key.

5 The READY (

) indicator on the operator panel lights and the printer gets ready to print.

Printing a Status Page

To test the printer, print a status page indicating factory settings.
1 Press the MENU key on the operator

panel.

2 Press the
or key repeatedly until the message display shows Print Status Page.

Print Status Page

3 Press the ENTER key twice. The mes2 times press
sage display indicates Processing during printing of the status page, then returns to Ready. If the status page prints correctly, printer setup is complete. For details on using the printer, refer to the Operation Guide contained as a PDF file in the CDROM supplied with the printer.

Caution to user

Options Conforming to the Class B limits
DU-61 Duplexer SO-60 Sorter PF-60 Paper Feeder (500 sheets)
Warning: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the users authority to operate the equipment.

Caution labels

The labels shown are affixed to the printer. Label inside the printer (Laser radiation warning)
(European/Pacific countries) (U.S.A/Canada) Label on the printers rear panel

Label inside the rear

Ozone concentration
The printers generate ozone gas (O3) which may concentrate in the place of installation and cause an unpleasant smell. To minimize concentration of ozone gas to less than 0.1 ppm, we recommend you not to install the printer in a confined area where ventilation is blocked.

IMPORTANT SAFEGUARDS

1. 2. 3. 4. 5. Read all of these instructions and save these instructions for later use. Unplug this product from the wall outlet before cleaning. Do not use this product near water. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. Slots and openings in the cabinet and the back are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the groundingtype plug. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord ampere rating.
9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. Except as explained elsewhere in Users Manual, do not attempt to service this product yourself. Removing covers may expose you to dangerous voltage points or other risks. Refer all servicing in those compartments to service personnel. 11. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: ABCDWhen the power cord or plug is damaged or frayed. If liquid has been spilled into the product. If the product has been exposed to rain or water. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. If the product has been dropped or the cabinet has been damaged.

Canadian Department of Communications compliance statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformit aux normes du ministre des Communications du Canada
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.

ISO 7779

Maschinenlrminformationsverordnung 3. GSGV, 18.01.1991: Der hchste Schalldruckpegel betrgt 70 dB(A) oder weniger gem ISO 7779.

CE Marking Directive

According to Council Directive 89/336/EEC and 73/23/EEC Manufacturers name: Kyocera Mita Corporation, Tamaki Plant Manufacturers address: 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan declares that the product Product name: Page Printer Model number: FS-3820N/FS-3830N (as tested with the enhancement optional unit: PF-60, DU-61, and SO-60) Conforms to the following product specifications. EN 55 022:1998 Class B EN 61 000-3-2:1995 EN 61 000-3-3:1995 EN 55 024:1998 EN 60 950:2000 EN 60 825-1:1994+A1+A2 The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned. Users instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information
Declaration of Conformity (Australia)
Manufacturers name: Manufacturers address: declares that the product Product name: Page Printer Model number: FS-3820N/FS-3830N (as tested with the enhancement optional units: PF-60, DU-61, and SO-60) Description of device: This Page Printer Model FS-3830N is the 33 ppm (FS-3820N is the 28 ppm); A4 size and utilized plane paper; laser; dry toner etc. The printer can be equipped with several enhancement optional units as a paper feeder as PF-60, a duplexer as DU-61, a sorter as SO-60 etc. Conforms to the following product specifications. AS/NZS 3548: 1995 (EN 55 022:1994 Class B) IEC60950 (EN 60 950:2000) IEC60825-1 (EN 60 825-1:1994+A11+A2) The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned. Users instruction that conforms to the applicable specifications Technical drawings Descriptions of the procedures that guarantee the conformity Other technical information Kyocera Mita Australia Pty., Ltd. 6-10 Talavera Road, North Ryde, NSW, 2113, Australia Phone: +61 2-9888-9999 Fax: +61 2-9888-9588 Kyocera Mita Corporation, Tamaki Plant 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan

Declaration of Conformity (U.S.A.)
Model Number: Trade Name: Responsible Party: Address: Telephone number: Fax number: Manufacturers name: Manufacturers address: Laser Printer FS-3820N/FS-3830N (as tested with enhancement optional units: PF-60, DU-61, SO-60.) Kyocera Kyocera Mita America Inc. 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-0008, U.S.A. (973) 808-8444 (973) 882-6000 Kyocera Mita Corporation, Tamaki Plant 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned. Users instruction that conforms to the applicable specifications. Technical drawings. Descriptions of the procedures that guarantee the conformity. Other technical information. Kyocera Mita America Inc.

Disclaimer

We shall have no liability or responsibility to customers or any other person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by equipment sold or furnished by us, including but not limited to, any interruption of service, loss of business or anticipatory profits, or consequential damages resulting from the use or operation of the equipment or software.
Prolonged Non-Use and Moving the Printer

Prolonged Non-use

If you ever leave the printer unused for a long period of time, remove the power cord from the wall outlet. We recommend you consult with your dealer about the additional actions you should take to avoid possible damages that may occur when the printer is used next time. When you move the printer: Move it gently. Keep it as level as possible, to avoid spilling toner inside the printer as shown in the figure. The handhold on the right side of the printer doubles as the memory card slot. Be sure to remove the memory card first, if inserted, before lifting or moving the printer. Be sure to remove all the option units such as the sorter and duplexer before moving the printer. If you need to move the printer to another location, remove the toner container, waste toner box, and developer unit. The procedure for removing these is as follows: 1 Remove the toner container and waste toner box from the printer. Put the toner container into the plastic bag in which it was supplied to prevent spilling of toner. Close the cap of the waste toner box tightly. Disconnect the connector of the developer unit from the printer and while pulling the developer unit release lever, remove the developer unit from the printer (1). Close the protect cover on the developer unit (2) and put the developer unit into the supplied plastic bag (3).

Moving the Printer

(1) Remove the developer unit.
(2) Close the protect cover.
(3) Put the developer unit.

1. Disconnect 2. Pull

Protect Cover Developer Unit 3 Put the printer into the box in reverse order of the unpacking procedure (Refer to STEP 1 Unpacking). Position the pad as shown in the figure, then place the toner container and waste toner box.

Plastic bag (supplied)

Toner Container Waste Toner Box

Printer Packing Carton

FS3830NIG1.fm 27
Push the center as shown in the figure to make space for the developer unit.
Put the developer unit into that space.
Developer Unit To reinstall the developer unit into the printer, use the reverse procedure of the above.

ENERGY STAR

As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency. The basic objective of the ENERGY STAR Program is to reduce environmental pollution by encouraging the manufacture and sale of equipment that uses energy more efficiently. This printer is equipped with a sleep timer function that conforms with the standards of the ENERGY STAR Program. This function makes it possible to reduce the amount of electrical power consumed by the printer. For maximum power savings, turn off the printers power supply when not using the printer for extended periods of time. For details on the sleep timer function and printer power consumption, refer to the CD-ROM instruction manual provided with the printer. Initial settings of the sleep timer function and power saved using the sleep timer function: Model name FS-3820N FS-3830N Initial sleep mode setting 15 minutes (30 minutes) 15 minutes (60 minutes) Power consumption in sleep mode 13 W (30 W) 13 W (40 W) ( ): ENERGY STAR program guideline
Group for Energy Efficient Appliances (GEEA)
The goal of GEEA is efficient use of energy. This product has a high-efficiency profile and meets the criteria for receiving the GEEA-Label. Model name FS-3820N FS-3830N Initial sleep mode setting 15 minutes (30 minutes) 15 minutes (60 minutes) ( ): GEEA criteria Power consumption Power off 0 W (1 W) Sleep mode 13 W (15 W)

Options

The following options are available for the printer.

1 Sorter (SO-60)

Sorter (SO-60)
Equipped with five trays each with 200 sheets capacity. Performs sorting, collating, and mailbox function. Attaches to the top of the printer.

2 Rear Tray

Printer
It attaches to the rear of the printer.
3 Network Interface Card (IB-20/21E/22)
Insert the card into the option interface slot at the rear of the printer. The printer can be used on network environments including Windows, Macintosh, UNIX, NetWare, etc.

Serial lnterface Board Kit (IB-11)

Envelope feeder (EF-60)

Network Interface Card (3.3 V DC) or Serial Interface Board Kit (IB-11)
Connect to the computers serial printer port with a serial cable.
4 Envelope Feeder (EF-60)
Holds more envelopes at a time than the MP tray. This envelope feeder can be attached to the front of the printer after the MP tray has been removed.

5 Duplexer (DU-61)

Performs duplex printing for short edge and long edge binding. Attaches to the bottom of the printer.
5 Duplexer (DU-61) 6 Paper feeder (PF-60)
of n er tio d a Or tall s In

6 Paper Feeder (PF-60)

Holds approximately 500 sheets of A5 to A4/Letter and Legal size paper. Up to three paper feeders can be attached to the bottom of the printer unit.
Other Options Paper Cassette (PC-60LG)
Holds A5 to A4/Letter and Legal size paper. Holds approximately 2,000 sheets of 76 to 216 mm (3 to 8-1/2") 148 to 305 mm (5-13/16 to 12") size paper. This bulk paper feeder can be attached to the front of the printer after the MP tray has been removed, but can only be installed on the FS-3830N.
Bulk Paper Feeder (PF-8E)
Memory DIMM, CompactFlash card, Microdrive (Hard Disk Unit)
See your dealer for purchasing information of these optional devices that are best suited for use with this printer.
Printer combined with options

FS3830NIG1.fm 29

Regarding Trademarks
PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL and KIR (Kyocera Image Refinement) are trademarks of Kyocera Mita Corporation. Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company. Centronics is a trade mark of Centronics Data Computer Corp. PostScript is a registered trademark of Adobe Systems Incorporated. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. ENERGY STAR is a U.S. registered mark. This Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL 6 language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A. This product was developed using the Tornado Real Time Operating System and Tools from Wind River Systems. This product contains UFST and MicroType from Agfa Monotype Corporation.

IBM Program License Agreement
The device you have purchased contains one or more software programs ("Programs") which belong to international business machines corporation ("IBM"). This document defines the terms and conditions under which the software is being licensed to you by IBM. If you do not agree with the terms and conditions of this license, then within 14 days after your acquisition of the device you may return the device for a full refund. If you do not so return the device within the 14 days, then you will be assumed to have agreed to these terms and conditions. The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the country where you acquired the Programs. You obtain no rights other than those granted you under this license. The term "Programs" means the original and all whole or partial copies of it, including modified copies or portions merged into other programs. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.

1. License

Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the device to another party. If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is then terminated. The other party agrees to these terms and conditions by its first use of the Program. You may not: 1) use, copy, modify, merge, or transfer copies of the Program except as provided in this license; 2) reverse assemble or reverse compile the Program; or 3) sublicense, rent, lease, or assign the Program.

2. Limited Warranty

The Programs are provided "AS IS." There are no other warranties covering the programs (or conditions), express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

Laser Safety

Laser Notice
This printer is certified as a Class I laser product conforming to the requirements of IEC 825.
DANGER: LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This page intentionally left blank.

FS3830NIG2.fm 34

Operator Panel
For more details on operating procedures, see the Operation Guide contained as a PDF file in the CD-ROM supplied with the printer.

INTERFACE SIZE TYPE

ATTENTION

Indicator

Ready indicator Data indicator Attention indicator

Description

Flashing: Indicates when an error occurs that you can clear by yourself. Lit: Indicates that the printer is on-line. Printing is possible. Off: Indicates that the printer is off-line. Data can be received but will not be printed. Also indicates when printing is automatically stopped due to occurrence of an error. Flashing: Indicates data transfer is taking place. Lit: Indicates either that data is being processed, or that data is being written to the memory card. Flashing: Indicates when the printer needs maintenance attention or the printer is warming up (Please wait). Lit: Indicates when a problem or an error occurs that you can clear by yourself. (For example, paper jam occurs.)

Message Display

INTERFACE
Interface indicator Paper size indicator Paper type indicator
The interface indicator shows which of the printers interfaces is currently active. The default is no selection (---). Indicates the paper size of the current paper cassette. The default is A4 (A4) size. Indicates the paper type of the current paper cassette. The default is PLAIN.
If the number of pages to be printed is set to 2 or more, when printing starts, the lower line of the message display shows the number of printed pages/set number of pages to be printed.

Function

Switches the printer on-line and off-line. Prints and feed out one page. Cancels specific errors. Wakes from sleep mode. Abandons a printing job, resets numeric values, or cancels a setting procedure. Used to stop the sounding of the alarm buzzer indicating the occurrence of an error. When pressed during mode selection, terminates the setting and returns to the Ready condition. Used to select the emulation, font, character code set; to read an memory card and others. Lets you access the desired item or enter numeric values. In some of the control procedures, the < and > keys are used to enter or exit the sub items. Enables access to the desired item or entering of numeric values. In some of the control procedures, the < and > keys are used to enter or exit the sub items. Used as the < key in the mode selection function. Used as the > key in the mode selection function. Displays online help messages on the message display when paper jam errors occur.

Finalizes numeric values and other selections.

Printed in Japan

2004. 1 7KKTB21E++AA