FS-9100DN, FS-9500DN, FS-9120DN, FS-9520DN Replenishing Toner
This section explains how to replace the toner container. When replacing the toner container, always replace the waste toner box at the same time. If this box is full, the printer may be damaged or contaminated by the waste toner that may spill over the box.
NOTE: During toner container replacement, temporarily put storage media
and computer supplies (such as floppy disks) away from around the toner container. This is to avoid damaging media by the magnetic content of the toner. You do not have to turn printer power off before starting the replacement. Any data that may be under printing process in the printer will be deleted if you turn printer power off.
Open the printer front cover all the way.
Push the lock lever up and gently remove the toner container until its handle appears.
NOTE: Do not pull the toner container all the way out as it can fall.
Grasp the handle on the toner container, push the lock lever up again and gently lift the toner container.
Seal up the old toner container with the supplied plastic bag and dispose of it.
Lightly tap the new toner on the top 5 to 6 times.
Thoroughly shake the toner container (in the direction of the arrows) ten times or more to loosen and mix the toner inside.
Grasp the handle on the toner container and insert the toner container along the rail of the printer.
When inserting, be sure that the gear side of the toner container faces the printer. Leave the front cover open to allow insertion of the waste toner box.

Gear Side To the Printer

Hold the toner container using both hands and fully insert it into the printer.

Close the front cover.

Replacing the Waste Toner Box
When replacing the toner container, the used waste toner box in the printer should also be replaced with the new one from the new toner kit. The printer will not operate without replacing the waste toner box. The old waste toner box has two stickers (explained as A and B) at the front. These stickers are used to seal the opening to prevent the waste toner from spilling out.
Open the printer front cover all the way. Remove the old waste toner box as shown in the figure.
Peel sticker A off the waste toner box.
Turn around the waste toner box. Stick sticker A over the opening at the back.
Peel off the backing paper to gain access to sticker B.
Peel sticker B off the waste toner box.
Stick sticker B down over top of sticker A at the back.
Seal up the old waste toner box with the supplied plastic

bag and dispose of it.

Fit the new waste toner box to the printer.

Close the front cover

FS-9120DN Specifications basic specifications:
Configuration: Resolution: Printer Memory: Electrical Requirements: Dimensions: Weight: Max Duty Cycle: Network Monochrome Printer with Standard 500 x 2 Drawer, Duplex unit, plus 200 Sheet Multi-Purpose Tray Fast 1200 dpi (1800 x 600), 600 x 600 dpi, 2400 x 600 dpi (w/KIR) Standard 32MB, upgradable to 544MB via 100 pin DIMMs, Optional HDD, Standard CF Card Slot (Type 1) 120V, 60Hz, 10.9A 23"W x 25.2"D x 24.2"H 147.9 lbs 180,000 Pages Per Month
paper handling options: dual paper drawers: PF-70
Paper Capacity: Paper Weight: Paper Size: Dimensions/Weight: 2 x 500Sheets 16 - 28 lb Bond 5.5" x 8.5", 8.5" x 11", 8.5" x 14", 11" x 17" 23.2"W x 12.4"D x 23.0"H/57.4 lbs
large capacity tray: PF-75
Paper Capacity: Paper Weight: Paper Size: Dimensions / Weight: 3,000 Sheets 16 - 28 lb Bond 8.5" x 11" 23.2"W x 12.4"D x 23.0"H/48.0 lbs
controller specifications:
Controller: Supported PDL / Emulations: Fonts: Windows OS Compatibility: Novell OS Compatibility: Mac OS Compatibility: UNIX OS Compatibility: Connectivity / Interface: KUIO LV Expansion Slots (2): Supported Protocol: Driver: Utilities: PowerPC750CXe 400 MHz PRESCRIBE, PCL6 (PCL XL, PCL5e), KPDL3 (PS3), KCGL (HP-GL), Diablo 630, IBM ProPrinter X24, Epson LQ850, Line Printer 80 Outline Fonts for PCL XL/5e, 136 Outline fonts for KPDL3, 1 Bitmap Font Windows 95/98/Me/NT4.x/2000/XP Novell Netware 3.x/4.x/5.x OS 8.x/9.x/10.x Sun OS 4.1.x; Solaris 2.x; AIX; HP-UX (LPR) Standard 10/100BaseTX, Parallel IEEE1284, High Speed USB 2.0 Optional Hard Disk Drive Optional IB-20 10/100BaseTX, 10Base2; Optional IB-22 Enhanced Wireless NIC, Optional IB-11 RS-232C Serial TCP/IP IPX/SPX,AppleTalk, NetBEUI , KX Driver for Windows, PPD for Mac, PPD for Linux/UNIX KM-NET Viewer, KM-NET Remote Operation Panel, KM-NET Job Manager, KM-NET Printer Disk Manager, Network Advanced Setup Utilities, PRESCRIBE Utilities

finisher: DF-71

Stack Capacity Paper Size: Paper Weight: Staple Capacity: Edge Staple Position: Punch: Dimensions / Weight: Main Tray: 3,000 sheets; Sub Tray: 250 Sheets Main Tray: 8.5" x 11" - 11" x 17"; Sub Tray: 5.5" x 8.5 - 11" x lb Bond - 110 lb Index 50 Sheets: 8.5 x 11; 30 Sheets: 8.5 x 14, 11 x Positions:Top Left, Bottom Left, Left/Top Side Standard 2 and 3 Hole 27.1"W x 23.5"D x 41.5"H/110 lbs

simple finisher: DF-73

Stack Capacity Paper Size: Paper Weight: Staple Capacity: Edge Staple Position: Dimensions / Weight: Main Tray: 1,000 Main: 8x5 x 11 - 11 x 17; Sub; 5.5 x 8.5 - 11 x - 34 lb Bond 30 Sheets: 8.5 x 11; 20 Sheets: 8.5 x 14, 11 x Position:Top Left 21.9W x 23.5D x 41.5H / 110 lbs

output speeds:

Warm-Up Time: First Print Out: Pages Per Minute: Less than 25 Seconds Less than 7.0 Seconds 36 Letter, 20 Legal, 20 Ledger
saddle stitch finisher: DF-75
Stack Capacity: Paper Size: Paper Weight: Staple Capacity: Edge Staple Position: Saddle Stitch: Punch Unit: Dimensions / Weight: Main Tray: 1,000 Sheets Main: 5.5" x 8.5" - 11" x 17" 16 lb Bond - 110 lb Index 50 Sheets: 8.5" x 11"; 25 Sheets: 8.5" x 14", 11" x 17" 4 Positions:Top Left, Bottom Left, Left Side, Center 8.5" x 11", 11" x 17"; Up to 10 Sheets Optional 2 and 3 Hole 28.3"W x 23.7"D x 39.4"H/86 lbs

paper supply:

Standard Paper Sources: Drawer Paper Size: MPT Paper Size: Std/Max Paper Capacity: Paper Weight: Input Materials: Dual 500 Sheet Drwawers, 200 Sheet MPT 5.5" x 8.5", 8.5" x 11", 8.5" x 14", 11" x 17" 5.5" x 8.5", 8.5" x 11", 8.5" x 14", 11" x 17", Custom (3.5" x5.8" - 11.7" x 17.7") 1200 Sheets/4200 Sheets 16-28 lb Bond via Paper Drawers, 16 lb Bond - 110 lb Index via MPT Bond Paper, Recycled Paper,Transparencies, Labels, Envelopes

punch unit: PH-2

Paper Size: Paper Weight: Number of Holes: Weight: 8.5" x 11" - 11" x 17" 17 lb Bond - 110 lb Index 2 and 3 5.2 lbs

duplex unit:

Paper Size: Paper Weight: 5.5 x 8.5, 8.5 x 11, 11 x - 21 lb Bond
multi-bin mailbox: M-2107
Number of Trays: Tray Capacity: Paper Weight: Dimensions/Weight: Sheets: 5.5 x 8.5, 8.5 x 11; 50 Sheets: 8.5 x 14, 11 x - 21 lb Bond 20.0W x 15.7D x 18.5H / 22 lbs
options: hard disk drive:
Enables Document Printing and e-MPS Functions; Private Print, Job Storage, Quick Copy, Proof & Hold,Virtual MailBoxes, Bar Code

additional options:

Reversing Adapter for DF-75 (RA-1), Printer Stand

consumables:

TK-70 Toner Container: 40,000 pages @ 5% Coverage*
* Ships with 20,000 pages @ 5% Coverage
Specifications and design are subject to change without notice. All trademarks and registered trademarks are the property of their respective manufacturers.
Kyocera Mita America, Inc. 225 Sand Road, PO Box 40008, Fairfield, NJ 07004-0008, USA 2003 Kyocera Mita America, Inc.

www.kyoceramita.com