Do not remove the cover (or back). This may cause electric shock or fire. Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center.
This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor. This may cause a malfunction, electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances.
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.

Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 20 inch Wide (51 cm) - 1680 x inch Wide (56 cm) - 1680 x 1050
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.
Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of children's reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.
Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular. Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 24 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast. >> Click here to see an animation clip Brightness button [ ] Adjust buttons [ Enter button [ ] / SOURCE button ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Adjust items in the menu. Activates a highlighted menu item. / Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. Use this button for auto adjustment. >> Click here to see an animation clip Use this button for turning the monitor on and off. This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.
AUTO button Power button [ ] Power indicator
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
The configuration at the back of the monitor may vary from product to product. POWER port DVI IN (HDCP) port RGB IN port Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. For using a locking device, contact where you purchase it.
See Connecting Cables for further information regarding cable connections.

Connecting Cables

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. - Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN] Using the DVI (Digital) connector on the video card. - Connect the DVI Cable to the DVI Port on the back of your Monitor. [DVI IN (HDCP)] Connected to a Macintosh. -Connect the monitor to the Macintosh computer using the D-sub connection cable. If the monitor and the computer are connected, you can turn them on and use them.

Using the Stand

Monitor Assembly

Monitor and Bottom

Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately)
Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove three screws and then remove the stand from the LCD monitor. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Monitor Driver

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Installing the Monitor Driver (Automatic) Insert the CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button (Microsoft Windows XP/2000 Operating System).
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/
Monitor driver installation is completed.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
Microsoft Windows XP Operating System Insert the CD into the CD-ROM drive. Click "Start" "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced."
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver." and select "Install from a list or." then click "Next" button.
Select "Don't search ,I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button.
Click the "Close" button then click the "OK" button continually.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button.
How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click the "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.

Microsoft Windows Millennium Operating System Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver." Choose "Display a list of all the driver in a specific location." then click the "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click the "OK" button.
Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft Windows NT Operating System Click "Start," "Settings," "Control Panel," and then double-click the "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) "Enter" the model name of your monitor. This information will not affect the actual execution of XWindow. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.

Picture

Description You can use the on-screen menus to change the brightness according to personal preference.

Play/Stop

Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip

MENU , MENU

Contrast
You can use the on-screen menus to change the contrast according to personal preference.

MENU , , MENU

Description MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

MagicColor

Off Demo
Returns to the original mode. The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. Full Displays not only vivid natural color but also more realistic natural skin color with clearness. Intelligent Displays vivid natural color with clearness. The tone of the color can be changed and one of four modes can be selected -Cool, Normal, Warm and Custom.

MENU , , , MENU

Color Tone

Color Control

Adjusts individual Red, Green, Blue color balance. -Red, Green, Blue

MENU , , , , MENU

Gamma correction changes the luminance of the colors with intermediate luminance. Gamma - Mode 1 - Mode 2 - Mode 3
Description Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.

Coarse

Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed).
Changes the clearance of image. Sharpness

H-Position

Changes the horizontal position of the monitor's entire display.

V-Position

Changes the vertical position of the monitor's entire display.
Description You can choose one of nine languages.

Language

The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
You can change the horizontal position where the OSD menu appears on your monitor.
You can change the vertical position where the OSD menu appears on your monitor.
Change the transparency of the background of the OSD. Transparency

Display Time

The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off. - 5 sec, 10 sec, 20 sec, 200 sec
Description Select Auto Source for the monitor to automatically select the signal source.

Auto Source

Image parameters are replaced with the factory default values. Image Reset
Color parameters are replaced with the factory default values. Color Reset

RTA (Response Time Accelerator) A function that accelerates the response speed of the panel so as to provide a sharper and more natural video display. RTA On : Activates the RTA function so that the panel operates at a higher response speed than its original speed. RTA Off : Deactivates the RTA function so that the panel operates at its original response speed. If you turn the power off and on again after switching RTA off, the RTA function is automatically switched On (Factory Setting)

Information

Description Shows a video source, display mode on the OSD screen.

MENU ,

Check List
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Symptom No images on the screen. I cannot turn on the monitor.
Check List Is the power cord connected properly? Can you see "Check Signal Cable" on the screen?
Solutions Check the power cord connection and supply.
(Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press SOURCE button to have the monitor double-check the input signal source.
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Can you see "Not Optimum Mode", "Recommended Mode 1680 X Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 X Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 X Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.)

There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Connected using the DVI cable?
You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. Unlock the OSD by pressing the [MENU / button for at least 5 seconds. ]
I cannot see the On Screen Display.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
The screen shows strange colors or just black and white.
Check the signal cable connection. Make sure the video card is fully inserted in it's slot.

Reboot the computer.

Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel Display Settings. Has the video card been set properly? There is a message that reads "Unrecognized Have you installed the monitor driver? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions.

There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Have the Windows colors been set properly?
monitor, Plug & Play (VESA DDC) monitor found".
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Install the monitor driver according to the Driver Installation Instructions.
Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution.) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Q&A

Question How can I change the frequency? Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP : Set the resolution in the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution in the Control Panel Settings.

Display

Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP : Set the resolution in the Control Panel Appearance and Themes Display Screen Saver. Set the function in the BIOS-SETUP of the computer. Windows ME/2000 : Set the resolution in the Control Panel Display Screen Saver. Set the function in the BIOS-SETUP of the computer. Refer to the Windows/Computer Manual How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.

Self-Test

Self-Test Feature Check | Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Self-Test Feature Check Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or damaged. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.

Environment The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1680 X Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.

SyncMaster 206BW

Specifications
General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7M Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB, 0.7 Vp-p 5%, TTL level (V high 2.0V, V low Maximum Pixel Clock 146 MHz (Analog,Digital) Power Supply AC 100 - 240V~ (+/- 10%) Signal Cable 50/60Hz 3Hz 1680 X 1050@60 Hz 1680 X 1050@60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 20 " Wide Diagonal (51 cm) 433.44 mm (H) x 270.9 mm (V) 0.258 mm (H) x 0.258 mm (V) SyncMaster 206BW
15pin to 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable, (Option) Dimensions (W x H x D) / Weight 476.0 X 329.0 X 65.2 mm / 18.7 x 12.9 x 2.5 inch (Without Stand) 476.0 X 396.4X 219.3 mm / 18.7 x 15.6 x 8.6 inch (With Stand) / 5.3 kg / 11.6 lbs VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 F ~113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing

Storage

Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms. For example, the number of TFT LCD sub pixels contained in this product are 5,292,000. Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number
of the Horizontal Cycle is called the Horizontal Frequency. Unit : kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit : Hz

SyncMaster 226BW

General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7M Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB, 0.7 Vp-p 5%, TTL level (V high 2.0V, V low Maximum Pixel Clock 146 MHz (Analog,Digital) Power Supply AC 100 - 240V~ (+/- 10%) Signal Cable 50/60Hz 3Hz 1680 X 1050@60 Hz 1680 X 1050@60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 22 " Wide Diagonal (56 cm) 473.8 mm (H) x 296.1 mm (V) 0.258 mm (H) x 0.258 mm (V) SyncMaster 226BW
15pin to 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Option) Dimensions (W x H x D) / Weight 514.6 X 353.3 X 63.0 mm / 20.2 x 13.9 x 2.4 inch (Without Stand) 514.6 X 422.0 X 219.3 mm / 20.2 x 16.6 x 8.6 inch (With Stand) / 4.9 kg / 10.8 lbs VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 F ~113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA Europe 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 1-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com/co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx

BELGIUM CZECH REPUBLIC DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN U.K CIS RUSSIA UKRAINE Asia Pacific AUSTRALIA CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN
( 0,15/min) 01805 - 121213 ( 0,12/Min) 88 ( 0.10/Min) SAMSUNG (7267864)
http://www.samsung.com/be http://www.samsung.com/cz http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/uk
8-800-200-0400 8-800-502-0000
http://www.samsung.ru http://www.samsung.com/ur
603 800-810-5858, 010- 3030 8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 02-689-3232 0800-329-999
http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw
VIETNAM Middle East & Africa SOUTH AFRICA U.A.E

588 889

http://www.samsung.com/vn
(SAMSUNG) 800SAMSUNG (7267864)
http://www.samsung.com/za http://www.samsung.com/mea
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm
Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit : Hz Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz
Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.

906BW 206BW 226BW

Widescreen Analog/Digital LCD Monitors
19", 20" and 22" widescreens Microsoft Windows Vista Premium certification High native resolutions High-gloss, piano black bezel and case MagicSpeed ultra-fast 2 ms (G to G) response time 160/160 horizontal/vertical viewing angles Exclusive Magic technologies 16:10 aspect ratio
imagine having elbow room on screen. Thats exactly what you get with the Samsung 6-series of widescreen LCD monitors. Certified to meet Microsoft Vistas Premium standards, the wide 16:10 aspect ratios of these professional-level monitors make multitasking easy. Theres room for more applications. Room for multiple images. Room for all your tool palettes. An ultra-fast 2 ms (G to G) response time is perfect for motion editing. And exclusive Magic technologies give you complete control over outstanding color. All the color. All the room. With the Samsung 6-series, its not hard to imagine.
Features Widescreen Format Whether youre creating a masterpiece or just watching one on DVD, the wide 16:10 aspect ratio and 1680 x 1050 resolution deliver a better view. Microsoft Windows Vista Premium Certification Premium certification is reserved only for products proven to take full advantage of everything the Microsoft Windows Vista operating system offers. MagicSpeed 2 ms Response Time Fast pixel response means fast action with virtually no blurring or ghosting. MagicColor and MagicBright 3 Enjoy rich, natural color and easily selectable brightness modes that include Text, Internet, Game, Sports, Movie and Print view.

Specifications

Panel Type Viewable Size Pixel Pitch Brightness (typical) Contrast Ratio (typical) Response Time (typical) Viewing Angles (H/V) Native Resolution Aspect Ratio Maximum Color Interface Input Video Signal Sync Type Input connetcors Plug and Play Power Consumption Stand Type Cabinet Color VESA Wall Mount Magic Technologies
a-si TFT/TN 19.0" Wide 0.285mm 300 cd/m
a-si TFT/TN 20.0" Wide 0.258mm 300 cd/m
a-si TFT/TN 22.0" Wide 0.282mm 300 cd/m2 3000:1 DC 2 ms (G to G) 160/x 1050 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite, SOG 15-pin D-sub, DVI-D DDC 2B 55 Watt (max.), <2 watt (DMPS mode) Simple Piano black 100 mm MagicTune with asset management, MagicSpeed, MagicColor , MagicBright 3 Windows, Windows Vista, Mac, Sun DVI (HDCP), Swivel and tilt 20.3" x 16.6" x 8.6" (without stand: 20.3" x 2.5" x 13.9") 16.3 lbs. 3/3
2000:1 DC 2 ms (G to G) 160/x 900 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite H/V, SOG 15-pin D-sub, DVI-D DDC 2B 42 watts (max.), <1 watt (DMPS mode) Simple Piano black 75 mm MagicTune with asset management, MagicSpeed, MagicColor , MagicBright 3 Windows, Windows Vista, Mac, Sun DVI (HDCP), Swivel and tilt 17.6" x 14.3" x 7.9" 9.3 lbs. 3/3
3000:1 DC 2 ms (G to G) 160/x 1050 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite, SOG 15-pin D-sub, DVI-D DDC 2B 55 Watt (max.), <2 watt (DMPS mode) Simple Piano black 75 mm MagicTune with asset management, MagicSpeed, MagicColor , MagicBright 3 Windows, Windows Vista, Mac, Sun DVI (HDCP), Swivel and tilt 18.7" x 15.6" x 8.6" (without stand: 18.7" x 2.6" x 12.9") 12.6 lbs. 3/3
MagicTune with Asset Management Monitor adjustments are made via the mouse, for a cleaner, sleeker monitor with fewer buttons. Wall-Mountable Whether its on your desk or hanging on your wall, theyll make you look good.
Compatibility Special Features Dimensions (W x H x D) Net Weight Warranty (P/L)

906BW Dimensions

17.6"

206BW Dimensions

18.7"

226BW Dimensions

20.3"

14.3"

15.6"

16.6"

Product Information: 1-866-542-7214 Product Support: 1-800-SAMSUNG

www.samsung.com/monitor

2007 Samsung Electronics America, Inc. Samsung is a registered mark of Samsung Electronics Corp., Ltd. Specifications and design are subject to change without notice. See www.samsung.com for detailed information. Printed in USA. 226BW1/07R2