Samsung SD-616E Manual
Samsung SD-616E Dvd Recorder, size: 664 KB
Part Numbers: SD-616E-GAME, SD616EGAME, sd-616e-game
Here you can find all about Samsung SD-616E, for example driver and firmware. You can also write a review. [ Report abuse or wrong photo | Share your Samsung SD-616E photo ]
User reviews and opinions
|arthurb999||11:23pm on Wednesday, August 25th, 2010|
|Works great, reads all my disks just fine. I just got the DVD Drive today and i am still waiting on my case to come, no problems with this drive, very slient, great deal. Just got this in yesterday, works great plays all media. Newegg rocks.|
Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.
SAMSUNG DRIVE REPLACEMENT TUTORIAL
By Kash (Look for me in on EFNET as Kashsteve)
Materials you will need: 1) Soldering Iron (15-30 Watt switchable from Radio-shack is what I used) 2) Copper De-soldering Braid (or pump, but braid is my preference) 3) SAMSUNG SD-616T or SD-616F (Check picture to see where you can find out what kind of drive yours is.) 4) Screwdriver 5) SDG-605B Bios for flashing (DO NOT ASK ME WHERE TO FIND THIS) 6) 30 Gauge wire 7) Solder (Rosin-core and Silver-bearing solder is recommended) 8) PIN-HEADER for yellow cable, or OLD THOMSON (thx to evrready_ for hookin me up via U$ MAIL) 9) LOTS OF TAPE and some hot glue. Step 1: Make sure your Samsung drive is a SD-616T or F. As long as its not a SD616Q You should be in good shape.
YES SD-616T Mine reads.
After flashing the DVD-ROM with the SDG-605 BIOS in your computer,
Pull out the drive using a paper clip and remove the tray face plate then the drive face plate:
Now pop off that tray faceplate by holding the dvd-rom upside down and pushing outward and up.
Then push in the side plastic clips of the drive and remove the faceplate:
K nubs. Easy part is over. Step 3: Remove the metal shielding on the top and bottom:
You should get something that looks like this. Step 4: Now you have to remove the front PCB, first unclip the plastic clip on the right then lift the PCB slightly hard on the left, dont be afraid, you might break the plastic, but dont pull hard enough to break the PCB. Then unclip the bottom clip holding the Motor then lift upwards until you get something like this:
After that, unclip the top clip and lift the PCB off. It may take a bit of work, be gentle, dont break anything!!!!!!!!!!!! After you take the PCB off, un-plug the tape cable on the bottom left from the Bottom PCB. Be gentle! Shimmy the cable from one edge then the other.
Notice the sticker on the motor is facing the audio volume dial. (we want it to face the opposite direction.)
Step 5: Place the PCB between 2 books or something so it doesnt rock and De-Solder the Big Blobs holding the motor (Arrows pointing in red):
Put the copper braid over the solder, then put the soldering (set at 30 Watt) iron on the copper braid until the braid soaks up the solder. Repeat until all the solder is gone. (Use a nail clipper to cut the braid to get rid of the unwanted solder). The motor should fall off after you take off one of the solder blobs and heat the other:
Step 6: Rotate the motor 180 degrees so that the sticker is facing the black plastic pogo-pin type things. BEFORE: (sticker facing white dial)
AFTER: (sticker facing black pogo)
\ Then put the motor back into the drive like it was and put the Rubber ring back onto the motor and onto the black round gear that controls the tray. (You can spin the black round gear and see that it moves the tray back and forth. Make sure your tray is ejected half way so you can see the black round gear.)
Now, get the other PCB (the bottom one) and unclip it from the dvd-rom:
Lift the right side (push in the plastic clip) then lift off the right side
Then flip it over and put it on top of the TOP PCB.
Now you gotta break some plastic! (Before you break the plastic)
(after you break the plastic)
. Be careful though; dont damage anything, like the capacitor right below the plastic. (Use some pliers to break it. You must de-solder and remove the metal support that holds the plastic down)
Personally, I got my pin header from my old Thomson. You may not want to do this, but I couldnt figure out any other way to get the pin header. This was really hard and I wont explain how I got it:
Now, wiring: (THIS PIC I GOT FROM LOSTBOY)
Get 4 pieces of 30 GAUGE and cut them to a size about foot long, then connect 1 end of each of the wires to each of the points indicated as Pin 1, Pin 2, etc. (by the way, flip the bottom PCB back over to its original position) After you successfully do so, keep a mental note of which wire is Pin1, pin2 etc Then put the wires through the unused hole and then solder them onto the Pin-Header: (THIS PART FROM TIROS, well everything is from TIROS)
You must solder them in this way: -[: : : : : :]= |2 1| -|8 7|This is the back of the pin header
Pin 1 connects to 8 Pin 2 connects to 3 Pin 3 connects to 4 Pin 4 connects to 9 So you get something that looks like this:
Then after that youre pretty much done! Tape all the wires to the PCB so they do not interfere with the CD spinning.
Put some hot glue on the PCB and put the pin header on the PCB and Tape it down and then Re-assemble everything and you are DONE!
In order for this to work, you must have a power splitter and connect the power to both the hard-drive and the dvd-rom:
Now just put in your xbox and Try out an original! Then a CD-R of course. Once again, written by Kash, Inspired by xovationx, Lostboy and especially TIROS (really nice fellow)
K6742 CS-F34db4e5 PRO V5 Photo 700 AVR-1611 Hh325 VP Roadwinr PRO 3800 Logicom L900 PXI-H990 8707G CTE-630BT EK5143 TA-VE100 HV 500 Zoom 90 Durafon 1X Emoty AG4AH09-12-bwf01 1215AC DX130-JD Yamaha C-50 Asus S6F Batteries PB50 Dreamweaver TX-SR576 Travelmate 4670 KEH-P8850 Aspire 1360 TXL37G20E Passat CC GPS 155 Microtek 710S EK6322B VT999 Minolta 7025 Scala-600 Notebook PC 42FD9935-17 VP-D77I Yamaha S80 VGN-SZ71xn C Evohome Av-32h5 VCL-ES06 Lrsc26950ST ER-A150 DZ-MV550A DP382-NR AVR-1709 DVD-228 Usb Mono GTO963 DTH8040E 5536G DVD-1080PK 27R0508 MD 50 Firmware MX 3000 HT-SF100 700R-serials-001026501-thru-103029625 SA-930 SC-PM9 Nitrus SMX-F44SP Istart 2380 Photosmart B109 Evolution KNA-DV3200 Audio 5060 PI5500 SGH-E370 RX-ED77 W508A 32LG10R 36600 MT 975 TRU9480 RZ80eesw AVH-P5750DVD MS07AH TC180 SU2930 Mark 22 BDZ-A70 ICF-CD810 DVR90DEA M228WDP DCR-HC30E 176-34 V1 0 LX-M140A KDC-BT6544UY DVD-707PS IC-20L Software LSJ092V-3 Command DSP-AX8 Addressfixer
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101