Hardware Setup BIOS Setup Driver & Utility Multilingual QIG

IL9 Pro

Motherboard Socket 775
Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D
Intel 945P / ICH7 FSB1066 Dual DDR2 667

Appendix

PCI Express Gigabit LAN 4x SATA 3Gb/s 7.1 Channel HD Audio
IL9 Pro Users Manual English + Multilingual QIG 1st Edition, October 2006
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. This document contains materials protected under International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer and authors of this manual. If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail, we cannot guarantee any responsibility.

Hardware Setup

Contents

1. Hardware Setup... 1-1

1.1 1.2 1.3 1.4 1.5 1.6 Specifications...1-1 Motherboard Layout...1-2 Choosing a Computer Chassis..1-3 Installing Motherboard...1-3 Checking Jumper Settings..1-4 1.5.1 CMOS Memory Clearing Header and Backup Battery.1-4 Connecting Chassis Components...1-6 1.6.1 ATX Power Connectors...1-6 1.6.2 Front Panel Switches & Indicators Headers..1-7 1.6.3 FAN Power Connectors...1-8 1.6.4 Chassis Speaker Connector..1-8 Installing Hardware...1-9 1.7.1 CPU Socket 775...1-9 1.7.2 DDR2 Memory Slots... 1-11 1.7.3 PCI Express X16 Add-on Slots.. 1-12 Connecting Peripheral Devices.. 1-13 1.8.1 Floppy and IDE Disk Drive Connectors.. 1-13 1.8.2 Serial ATA Connectors.. 1-14 1.8.3 Additional USB 2.0 Port Headers... 1-15 1.8.4 Internal Audio Connectors.. 1-15 1.8.5 Front Panel Audio Connection Header.. 1-16 1.8.6 PCI and PCI Express X1 Slots.. 1-17 Connecting Rear Panel I/O Devices.. 1-18

BIOS Setup

Driver & Utility

2. BIOS Setup... 2-1

Multilingual QIG Appendix
3. Driver & Utility... 3-1 4. Multilingual Quick Installation Guide.. 4-3
4.1 ...4-3 4.1.1 ....4-3 4.1.2 ...4-4 4.2 ...4-7 4.2.1 ....4-7 4.2.2 ...4-8

5. Appendix... 5-1

5.1 Troubleshooting (How to Get Technical Support?).5-1 5.1.1 Q & A...5-1 5.1.2 Technical Support Form..5-4 5.1.3 Contact Information..5-5

1. Hardware Setup

1.1 Specifications
Support Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D Processor with 1066MHz FSB Supports Intel Hyper-Threading Technology 3x PCI

Internal I/O Connectors

1x Floppy port 1x ATA 100 IDE connector 4x SATA 3Gb/s connectors 2x USB 2.0 headers 1x FP-Audio header 1x CD-In connector

Chipset

Intel 945P / ICH7

Memory

4x 240-pin DIMM slots support maximum memory capacity up to 4GB Supports Dual Channel DDRUn-buffered Non-ECC memory

Rear Panel I/O

1x PS/2 Keyboard connector 1x PS/2 Mouse connector 1x COM port 1x LPT port 4x USB 2.0 connectors 1x RJ-45 Gigabit LAN connector 1x 7.1CH Audio Connector 1x S/PDIF Out

Onboard 10/100/1000M LAN

Onboard 7.1 CH HD Audio CODEC

Serial ATA

4x SATA 3Gb/s
100% Lead-free process and RoHS compliant

Expansion Slots

1x PCI-E X16 1x PCI-E X16 (PCI-E X4 bandwidth) 1x PCI-E X1

Miscellaneous

ATX form factor (305mm x 244mm)
Specifications and information contained herein are subject to change without notice.

1.2 Motherboard Layout

1.3 Choosing a Computer Chassis
Choose a chassis big enough to install this motherboard. As some features for this motherboard are implemented by cabling connectors on the motherboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the features required. If there is possibility of adopting some more hard drives, make sure your chassis has sufficient power and space for them. Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O shield of the chassis matches the I/O port configuration of this motherboard. You can find an I/O shield specifically designed for this motherboard in its package.

1.4 Installing Motherboard
Most computer chassis have a base with many mounting holes to allow the motherboard to be securely attached, and at the same time, prevent the system from short circuits. There are two ways to attach the motherboard to the chassis base: (1) with studs, or (2) with spacers. Basically, the best way to attach the board is with studs. Only if you are unable to do this should you attach the board with spacers. Line up the holes on the board with the mounting holes on the chassis. If the holes line up and there are screw holes, you can attach the board with studs. If the holes line up and there are only slots, you can only attach with spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots, you can slide the board into position aligned with slots. After the board has been positioned, check to make sure everything is OK before putting the chassis back on. Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component. Failing to so may cause severe damage to your motherboard and/or peripherals. Plug in the AC power cord only after you have carefully checked everything.
To install this motherboard: 1. 2. 3. 4. 5. Locate all the screw holes on the motherboard and the chassis base. Face the chassiss rear panel. Place all the studs or spacers needed on the chassis base and have them tightened. Face the motherboards I/O ports toward the chassiss rear panel. Line up all the motherboards screw holes with those studs or spacers on the chassis. Install the motherboard with screws and have them tightened. To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
1.5 Checking Jumper Settings
For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.
For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.

Pin 1~2 SHORT

Pin 2~3 SHORT
1.5.1 CMOS Memory Clearing Header and Backup Battery
The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu, or (d) whenever there is modification on the CPU or memory modules. This header uses a jumper cap to clear the CMOS memory and have it reconfigured to the default values stored in BIOS. Pins 2 and 3 shorted (Default): Normal operation. Pins 1 and 2 shorted: Clear CMOS memory.
To clear the CMOS memory and load in the default values: 1. 2. 3. 4. 5. 6. Power off the system. Set pin 1 and pin 2 shorted by the jumper cap. Wait for a few seconds. Set the jumper cap back to its default settings --- pin 2 and pin 3 shorted. Power on the system. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS setup menu right after powering on system. Set the CPU operating speed back to its default or an appropriate value. Save and exit the BIOS setup menu.

CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source. Nevertheless, this backup battery exhausts after some five years. Once the error message like CMOS BATTERY HAS FAILED or CMOS checksum error displays on monitor, this backup battery is no longer functional and has to be renewed.
To renew the backup battery: 1. 2. 3. 4. 5. Power off the system and disconnect with AC power source. Remove the exhausted battery. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The + side is its positive polarity. Connect AC power source and power on the system. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.
CAUTION: Danger of explosion may arise if the battery is incorrectly renewed. Renew only with the same or equivalent type recommended by the battery manufacturer. Dispose of used batteries according to the battery manufacturers instructions.
1.6 Connecting Chassis Components
1.6.1 ATX Power Connectors
These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors.
ATX 24-Pin Power Connector: The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector. Connect from pin-1 for either type. However, a 20-pin power supply may cause the system unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W or higher is recommended. ATX 12V 4-Pin Power Connector: This connector supplies power to CPU. The system will not start without connecting power to this one. Auxiliary 12V Power Connector: This connector provides an auxiliary power source for devices added on PCI Express slots.
1.6.2 Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark + align to the pin in the figure below stands for positive polarity for the LED connection. Please pay attention when connecting these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could cause system malfunction.
Definition HD LED + HD LED RESET RESET Reserved

Pin 6 8

Definition Message LED + Message LED Power Switch Power Switch
1.6.3 FAN Power Connectors
These connectors each provide power to the cooling fans installed in your system. CPUFAN1: CPU Fan Power Connector SYSFAN2~3: System Fan Power Connector These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
1.6.4 Chassis Speaker Connector

This header provides the connection to chassis speaker.

1.7 Installing Hardware

DO NOT scratch the motherboard when installing hardware. An accidentally scratch of a tiny surface-mount component may seriously damage the motherboard. In order to protect the contact pins, please pay attention to these notices: 1. A maximum 20 cycles of CPU installation is recommended. 2. Never touch the contact pins with fingers or any object. 3. Always put on the cap when the CPU is not in use.

1.7.1 CPU Socket 775

The installation procedures vary with different types of CPU fan-and-heatsink assembly. The one shown here is served for demo only. For detailed information on how to install the one you bought, refer to its installation guidelines.
1. Place the board so as to let the lever-hook of the socket is on your left side. Use your left thumb and forefinger to hold the lever hook, pull it away from the retention tab. Rotate the lever to fully open position.
3. Use your right thumb and forefinger to grasp the CPU package. Be sure to grasp on the edge of the substrate, and face the Pin-1 indicator toward the bottom-left side. Aim at the socket and place the CPU package vertical down into the socket.
2. Use your right-thumb to raise the load plate. Lift it up to fully open position.
4. Visually inspect if the CPU is seated well into the socket. The alignment key must be located in the notch of package.
5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. The cap plays an important role in protecting contact pins. In order to prevent bent pin, PUT ON the cap after operation or testing.
8. Place the heatsink and fan assembly onto the socket. Align the four fasteners toward the four mounting holes on the motherboard.
9. Press each of the four fasteners down into the mounting holes. Rotate the fastener clock-wise to lock the heatsink and fan assembly into position. 6. Lower the plate onto the CPU package. Engage the load lever while gently pressing down the load plate.
10. Attach the four-pin power plug from the heatsink and fan assembly to the CPU FAN connector. 7. Secure the lever with the hook under retention tab. A higher fan speed will be helpful for better airflow and heat-dissipation. Nevertheless, stay alert to touch any heatsink since the high temperature generated by the working system is still possible.

1.7.2 DDR2 Memory Slots

To reach the optimum performance in dual-channel configurations, install identical DDR2 DIMM pairs for each channel. Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain memory modules from the same vendor. Usually there is no hardware or BIOS setup required after adding or removing memory modules, but you will have to clear the CMOS memory first if any memory module related problem occurs.
To install system memory: 1. Power off the computer and unplug the AC power cord before installing or removing memory modules. Locate the DIMM slot on the board. Hold two edges of the DIMM module carefully, keep away from touching its connectors. Align the notch key on the module with the rib on the slot. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly.

1.7.3 PCI Express X16 Add-on Slots
These slots support the connections of graphics cards that comply with PCI Express specifications. This motherboard provides dual PCI-Express X16 slots for one or two graphics cards installation: One PCIE graphics card installation (Normal Mode): Install one PCIE graphics card into [Master] slot (the PCIEX1 slot on this motherboard).
Two PCIE graphics cards installation (CrossFire Mode): Install one CrossFire Edition graphics card into [Master] slot (the PCIEX1 slot on this motherboard), and one CrossFire Compatible graphics card into [Slave] slot (the PCIEX2 slot on this motherboard). The ATI CrossFire technology currently supports the Microsoft Windows XP with Service Pack 2 only. Slot PCI-E1 will be disabled when slot PCIEX2 is installed.
1.8 Connecting Peripheral Devices
1.8.1 Floppy and IDE Disk Drive Connectors
The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDC1 port and the floppy connector.
Each of the IDE port connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor, and 3-connector Ultra ATA/66 ribbon cables. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives.
Make sure to configure the Master and Slave relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector.
1.8.2 Serial ATA Connectors
Each SATA connector serves as one single channel to connect one SATA device by SATA cable.
To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the other end to SATA device. Attach the SATA power cable to the SATA device and connect the other end from the power supply. The motherboard in this illustration is served for DEMO only, may not be the same type or model as the one described in this users manual.

1.8.3 Additional USB 2.0 Port Headers
Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.

Pin 5 7

Pin Assignment VCC Data0 Data0 + Ground

Pin 10

Pin Assignment VCC Data1 Data1 + Ground NC
Make sure the connecting cable bears the same pin assignment.
1.8.4 Internal Audio Connectors
This connector connects to the audio output of internal CD-ROM drive or add-on card.
1.8.5 Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel. To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis. To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at pin 5-6, and pin 9-10 (default setting).

Pin 9 10

Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L
Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel
1.8.6 PCI and PCI Express X1 Slots
Install PCI Express X1 card into slot PCI-E1. Install PCI cards into slots PCI1, PCI2, and/or PCI3. Slot PCI-E1 will be disabled when slot PCIEX2 is installed.
1.9 Connecting Rear Panel I/O Devices
The rear I/O part of this motherboard provides the following I/O ports:
Mouse: Connects to PS/2 mouse. Keyboard: Connects to PS/2 keyboard. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. LAN1: Connects to Local Area Network. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. AUDIO1: Line-In/Surround: Either connects to the line out from external audio sources, or connects to the surround left and surround right channel. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel. Cen./Sub. (Center / Subwoofer): Connects to the center and subwoofer channel. S/PDIF Out: This connector provides an S/PDIF-Out connection through optical fiber to digital multimedia devices.

2. BIOS Setup

This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring system, or prompted to Run Setup. This chapter explains the Setup Utility of BIOS utility. After powering up the system, the BIOS message appears on the screen, the memory count begins, and then the following message appears on the screen:

PRESS DEL TO ENTER SETUP

If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del> keys, or by pressing the Reset button on computer chassis. Only when these two methods fair should you restart the system by powering it off and then back on. After pressing <Del> key, the main menu screen appears.
CMOS Setup Utility Copyright (C) 1985-2004, American Megatrends, Inc.
Standard BIOS Features Boot Configuration Features Advanced BIOS Features Advanced Chipset Features Power Management Features Hardware Health Configuration
BIOS Security Features Load Optimal Settings Load Best Performance Settings Save Changes and Exit Discard Changes and Exit
:Move +/-/:Value Enter:Select F1:General Help EXC:Exit F8:Best Performance Settings F9:Optimized Settings F10:Save Configure Time and Date. Display System Informaton V02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
In order to increase system stability and performance, our engineering staff is constantly improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for your reference only, and may not completely match with what you see on your screen.

3. Driver & Utility

The Driver & Utility CD that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the Driver & Utility CD into the CD-ROM drive in your system. The following installation auto-run screen appears. If not, browse the root directory of the CD-ROM via the File Manager, and double click the AUTORUN file.
[Drivers]: Click to enter the driver installation menu. [Manual]: Click to enter the users manual menu. [Utility]: Click to enter the utilities installation menu. [ [ Browse CD]: Click to browse the contents of this Driver & Utility CD. Close]: Click to exit this installation menu.

4. Multilingual Quick Installation Guide

4.1.1

1066MHz Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D Intel Hyper-Threading
1 1 ATA 100 IDE 4 SATA 3Gb/s 2 USB 2.0 1 FP-Audio 1 CD-In

DIMM 4GB DDRECC

1 PS/2 1 PS/2 1 COM 1 LPT 4 USB 2.0 1 RJ-45 Gigabit 1 7.1 1 S/PDIF

10/100/1000M

7.1 HD

4 SATA 3Gb/s

100% RoHS

Multilingual QIG

1 PCI-E X16 1 PCI-E X16 (PCI-E X4 ) 1 PCI-E X1 3 PCI

ATX 305mm x 244mm

4.1.2

abit

ATX [ATXPWR1][ATX12V1] ATX 2x12 [ATXPWR1] 2x2 [ATX12V1] [CPUFAN1]CPU [SYSFAN1] [AUXFAN1] [NBFAN1] [FPIO1]

IC

I/O I/O

I/O

[HLED] LED [RST] [SPKR] [SLED] LED [PWR] [PLED] LED
[FP-AUDIO1] HD () AC97 Ground USB VCC AVCC 4 10 (HD AUDIO) MIC2 L AGND MIC2 R AVCC FRO-R MIC2_JD F_IO_SEN FRO-L LINE2_JD 10 (AC97 AUDIO) MIC In GND MIC Power NC Line Out (R) NC NC Line Out (L) NC
PCB CMOS CMOS BIOS BIOS CMOS CMOS CMOS BIOS
USB [FP-USB1][FP-USB2] I/O USB USB VCC 10 VCC

[FDC1] IDE [IDE1][IDE2]

IEEE1394 [FP-1394-1] [FP-1394-2] I/O IEEE1394 IEEE1394 TPA0 + TPB0 + +12V 10 [CD1][AUX1] CPU (Central Processing Unit, CPU) CPU [CPUFAN1] TPA0 TPB0 +12V ATA [SATA1] ~ [SATA4] ATA ATA
Mouse PS/2 Keyboard PS/2 LPT1

OPT-IN1

S/PDIF

OPT-OUT1

AUDIO1: 7.1 / IEEE1394 IEEE1394 LAN1 USB1/USB2 USB

4.2.1

1066MHz Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D Intel

4.2.2

abit
ATX [ATXPWR1][ATX12V1] ATX 2x12 [ATXPWR1] 2x2 [ATX12V1] [CPUFAN1]CPU [SYSFAN1] [AUXFAN1] [NBFAN1] [FPIO1]

I/O

[HLED] HDD LED [RST] [SPKR] [SLED] LED [PWR] [PLED] LED
[FP-AUDIO1] HD () AC97 GroundUSB VCC AVCC 4 (HD AUDIO) MIC2 L AGND MIC2 R AVCC FRO-R MIC2_JD F_IO_SEN FRO-L LINE2_JD 10 (AC97 AUDIO) MIC In GND MIC Power NC Line Out (R) NC NC Line Out (L) NC
PCB CMOS CMOS BIOS BIOS CMOS

CMOS CMOS BIOS

IEEE1394 [FP-1394-1] [FP-1394-2] I/O IEEE1394 IEEE1394 TPA0 + TPB0 + +12V 10 [CD1][AUX1] CD-ROM CPU (CPU) CPU CPU [CPUFAN1] TPA0 TPB0 +12V ATA [SATA1] ~ [SATA4] ATA ATA

OPT-IN1 S/PDIF

OPT-OUT1 S/PDIF
AUDIO17.1 / IEEE1394 IEEE1394 LAN1 USB1/USB2 USB

5. Appendix

5.1 Troubleshooting (How to Get Technical Support?)

5.1.1 Q & A

Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer system? A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please move the CMOS jumper from its default 2-3 position to 1-2 for a few seconds, and then back. When you boot up your system for the first time, follow the instructions in the user's manual to load the optimized defaults. Q: If my system hangs when I update the BIOS or set the wrong CPU parameters, what should I do? A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always clear CMOS jumper before booting up again. Q: Why does the system fail to boot up again right after a mechanical power-off? A: Please keep a 30-second interval between each mechanical power On/Off. Q: Why does the system fail to boot up and nothing displays on the screen after I did some over-clocking or non-standard settings inside the BIOS? A: It should not cause hardware or permanent damage to motherboard when BIOS settings were changed from default to over-clocking or non-standard status. We suggest the following three troubleshooting methods to discharge CMOS data, recover the hardware default status, and then making the motherboard work again. There is no need to bother returning the motherboard to where you bought it from or go through an RMA process. Step 1.Switch off the power supply unit and then switch it on again after one minute. If there is no power-switch on the power supply unit, disconnect its power cord for one minute and then reconnect. Press and hold the <Insert> key on the keyboard, and press the power-on button to boot up system. If it works, release the <Insert> key and hit <Del> key to enter the BIOS setup page to apply the correct settings. If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step 2. Step 2.Switch off the power supply unit or disconnect the power cord. Open the chassis cover. Locate the CCMOS jumper near the button battery. Change the jumper position from default 2-3 to 1-2 for one minute to discharge the CMOS data, and then put it back to default 2-3 position. Close the chassis and switch on the power supply unit or plug in the power cord. Press the power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page to do the correct settings. If the situation remains the same, try Step 3.

Step 3.The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button battery during CMOS discharge.
Q: How to get a quick response for my request on technical support? A: Please carry out a simple troubleshooting before sending Technical Support Form: System boot-up fails after the system had been assembled: Check the motherboards supporting specifications first to see if all the key components attached in your system can meet. To do so, you may: Remove all the unnecessary add-on devices (except the CPU, VGA card, DRAM, and Power Supply), and then reboot. If the trouble still exists, try another VGA card of different brand/model to see if the system will start. If the trouble still exists, try another memory module of different brand/model. If the trouble still exists, try another CPU and Power Supply.
If the system runs successfully, shut it down and start re-installing the interface cards and devices that were previously installed in the system. Re-install and start the system one at a time until the system wont start. Malfunction in the OS: If the system hangs after resuming from S3 or some testing program, if the CPU cannot be recognized properly, if the display resolution mixed, or if a certain program cannot be executed, etc, you may: Upgrade the motherboards latest BIOS version. Upgrade the add-on devices latest driver version. Check if there is any conflict in the Control Panel/System Properties.
Q: How to fill in the Technical Support Form? A: To fill in this Technical Support Form, please refer to the following instructions: Region: Type in your country name. E-mail: Type in your contact E-mail information. First name: Type in your first name. Last name: Type in your last name. Subject: Type in the model name and the problem of your motherboard. Example 1: AA8XE and SCSI 29160 malfunction Example 2: AA8XE boot fails, POST code AF Example 3: AA8XE (system hang when S3 resume) Motherboard: Type in the model name and revision number of your motherboard. Example: AA8XE REV: 1.00 BIOS Version: Type in the BIOS version of your motherboard. (You can find it on the screen during the POST sequence.) CPU: Type in the brand name and the speed (MHz) of your CPU. (Illustrate the over-clocking status if you had done so.) Example: Intel 650 3.4GHz (OC FSB=220MHz) Memory brand: Type in the brand and model name of your memory module. Example: Memory brand: Kingston (KVR533D2N4/1G) Memory size: Type in the size of your memory module. Example: 512M* 4PCS

Memory configuration: Type in the memory configuration in BIOS setting. Example: Memory Timing: 2.5-3-3-7 @533MHz Graphics information: Note Graphics cards brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. Example: ATI RADEON X850 XT PE Graphics driver version: Type in the driver version of your graphics card Example: Catalyst 5.12V Power supply maker: Type in the brand and model name of your power supply unit. Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID allocation status. Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA 300GB (on SATA 3) Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1) Optical devices: Type in the brand and specifications of your optical drives and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports. Other devices: Indicate which add-on cards or USB devices that you absolutely sure are related to the problem. If you cannot identify the problems origin, indicate all the add-on cards or USB devices inserted on your system. Example: AHA 29160 (on PCI 2), Sandisk Cruzer mini 256MB USB Flash-disk. Operating system: Indicate which OS and language version Example: Microsoft Windows XP SP2, English version Example: Microsoft Media Center Edition 2005, Korean version Problem description: Describe the problem of your system configuration. Indicate the steps to duplicate problem if possible. See the next page for a blank Technical Support Form, or visit our website to fill in the form on line (http://www.abit.com.tw/page/en/contact/technical.php).
Q. Is the motherboard dead? Do I need to return it to where I bought from or go through an RMA process? A: After you had gone through the troubleshooting procedures, yet the problem still exists, or you find an evident damage on the motherboard. Please contact our RMA center. (http://www2.abit.com.tw/page/en/contact/index.php?pFUN_KEY=18000&pTITLE_IMG)
5.1.2 Technical Support Form
Region: E-mail: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memory size: Memory configuration: Graphics card: Graphics driver version: Power supply maker: Power supply wattage: Storage devices: Optical devices: Other devices: Operating system: Problem description:

5.1.3 Contact Information
Taiwan Head Office Universal ABIT Co., Ltd. No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-3380 Fax: 886-2-8751-3381 Sales: sales@abit.com.tw Marketing: market@abit.com.tw North America, South America Universal ABIT (USA) Corporation 2901 Bayview Drive, Fremont, CA 94538, U.S.A. Tel: 1-510-623-0500 Fax: 1-510-623-1092 Website: http://www.abit-usa.com Latin America: ventas@abit-usa.com RMA Center: http://rma.abit-usa.com UK, Ireland Universal ABIT UK Corporation Unit 3, 24-26 Boulton Road, Stevenage, Herts SG1 4QX, UK Tel: 44-1438-228888 Fax: 44-1438-226333 for technical support: technical@abitcomputer.co.uk for RMA no direct technical support: returns@abitcomputer.co.uk Tel: 44-1438-362088 Germany and Benelux (Belgium, Netherlands, Luxembourg), France, Italy, Spain, Portugal, Greece, Denmark, Norway, Sweden, Finland, Switzerland Universal ABIT NL B.V. Poland Universal ABIT Poland (Rep. office) Strzegomska 310/2, 54-432 Wroclaw Tel: +48-71-718-12-39 Fax: +48-71-718-12-38 Contact: Grzegorz Morgiel Turkey Universal ABIT Turkey (Rep. office) Tel: Shanghai Universal ABIT (Shanghai) Co. Ltd. FL 19 Xuhui Yuan BLOG NO.1089 ZhongShan s 2 RD, ShangHai 200030 The People's Republic of China Tel: (86-21) 54102211 Fax: (86-21) 54104791 Website: http://www.abit.com.cn Austria, Czech, Romania, Bulgaria, Slovakia, Croatia, Bosnia, Serbia, Macedonia, Slovenia Universal ABIT Austria Computer GmbH Schmalbachstrasse 5, A-2201 Gerasdorf / Wien, Austria Tel: 43-1-7346709 Fax: 43-1-7346713 Contact: office@abit-austria.at Website: http://www.abit-austria.at
Jan van Riebeeckweg 15, 5928LG, Venlo, The Netherlands Tel: 31-77-3204428 Fax: 31-77-3204420

http://www.abit.com.tw

P/N: 4310-0000-50 Rev. 1.00