CONTENTS

FUNCTIONS GENERAL INFORMATION BATTERIES SETTING UP BY CODE ENTRY SETTING UP BY MANUAL SEARCH SETTING UP BY AUTOSEARCH CODE SEARCHING BY BRAND NAME CODE IDENTIFICATION ALL OFF-FUNCTION TV VOLUME/MUTE PUNCH-THROUGH TOGGLE FUNCTION AUTO ZAPPING SHIFT FUNCTION

FUNCTIONS

SETUP Button

MODE Buttons

Videoplus Button/ G-Code Function Mute Button Program Up/Down Button VOLUME Button Teletext Colour Button
Numeric Buttons: 0-Digit/2 Digit Channel Input TOGGLE Button OK Button Up Down Left Right Exit Button Teletext Hold Button Info Button Teletext On Button POWER Button Teletext Off Button Teletext Mix Mode Button
AV Button ALL OFF Button Menu Button

Play FF Stop

Play Button Fast Forward Button Stop Button
Rew Rewind Button Pause Pause Button Rec Record Button
GENERAL INFORMATION This universal remote control is able to replace eight normal remote controls and can be used with the following audio and video components: TV VCR DVD ASAT DSAT CBL CD AUX television with teletext video recorder DVD-Player analogue satellite receiver digital satellite receiver Pay TV Decoder CD-Player for further equipment (TV, VCR, SAT, CD, DVD.)
BATTERIES You need 2 batteries LR 03/R03/AAA. Open the battery compartment at the back of the remote control. Please pay attention to the polarity of the batteries and the "+/-" marks. Put in the batteries. Close the compartment.
Do not throw empty batteries into your garbage bin! They have to be recycled if possible.
Note: When changing the batteries you have to reprogramme the remote control. Therefore it is useful to write down the code you have chosen in the beginning.
SETTING UP BY CODE ENTRY Please find the codes for operating your equipment enclosed in the codelist Press the "ON button to switch on the unit. 1 Press and hold "SETUP for 3 seconds. The mode LED lights up continually. (If you press the "SETUP button only once you activate the SHIFT- function). 2. Release "SETUP button. 3. Press and release desired Mode button to select the device you want to operate (TV, VCR, SAT, etc.). 4. Enter 3-digit-code for your brand from the list. The mode LED confirms each key pressed. 5. If code set-up was successful the mode LED turns off after having entered the last number. (If the code was incorrect the mode LED will blink 3 seconds before it goes out.) 6. The direct code entry is complete now.
If the device does not respond correctly, please repeat the setting up by trying the next code from the code list for your device until the equipment works properly. If none of the listed codes work, go to Chapter SETTING UP BY MANUAL SEARCH.
SETTING UP BY MANUAL SEARCH If the device does not respond to your remote control, although you tried all codes from the code list for your device, use the manual code search. With this function you can find the correct code even if your brand is not listed in the brand list. 1. Switch on the device you want to operate (TV, VCR, etc.). 2. Press and hold "SETUP for 3 seconds. The mode LED lights up continually. (If you press the "SETUP button only once you activate the SHIFT- function). 3. Release "SETUP button. 4. Shortly press the button for the mode you want to operate (TV, VCR, SAT). 5. Press "POWER repeatedly (it could be necessary to press the button 350 times to get all codes) or "PROG+ or "PLAY (only VCR) until the device you want to operate is switched off or working properly. The right code is found. 6. Press the button "OK briefly to store the code.
Note: There are approx. 350 different codes pre-programmed for each piece of equipment. In same cases it can be possible that only the most useful main functions are available. With some special devices the described proceeding cannot work out successfully.
The code search starts at the presently stored code number.
SETTING UP BY AUTOSEARCH With this function you can find the correct code also automatically: 1. Switch on the device you want to operate (TV, VCR, etc.) 2. Press and hold SETUP button for 3 seconds. The LED will light up continually after blinking. 3. Release SETUP button. 4. Shortly press the button for the mode you want to operate.(TV,VCR,SAT) 5. Shortly press the PROG+ button. The remote control transmits the codes successively (Interval 1 sec). If the device doesnt have a channel function press instead of PROG+ the PLAY or POWER button. 6. When the device reacts to the remote control press OK. If you missed to press OK in the right moment you can go back step by step to the right code by pressing PROG- Note: If you wish a larger transmitting interval (3 sec instead of 1 sec) press the PROG+ (PLAY,POWER) button twice in step 5.

CODE SEARCHING BY BRAND NAME This function makes it possible to search the code by the respective brand name. Find the names enclosed in the code table. Do as follows: Switch on the device you want to operate. 1. Press and hold "SETUP for 3 seconds. The mode LED lights up continually. (If you press the "SETUP button only once you activate the SHIFT- function). 2. Release "SETUP button. 3. Shortly press the button for the mode you want to operate (TV, VCR, SAT). 4. Enter the 1-digit-code from the code table. (code searching by brand name) 5. Press the button "POWER or "PROG+ or "PLAY several times until the device works as desired. 6. Store the code by pressing "OK. Did you run through all codes the mode LED blinks for about 3 seconds.

CODE IDENTIFICATION

This code identification gives you the possibility to select the stored codes directly with the remote control. 1. Press and hold "SETUP for 3 seconds. The mode LED lights up continually. (If you press the "SETUP button only once you activate the SHIFT- function). 2. Release "SETUP button. 3. Shortly press the button for the mode you want to operate (TV, VCR, SAT). If the operating modus is accepted the mode LED goes out for a moment. 4. Shortly press the "SETUP button. If the operating modus is accepted the mode LED goes out for an instant. 5. To find the first number press the numbered buttons shortly one after the other. If the code number is correct the mode LED goes out for a moment. This is the first stored number. For the second and third number use the same procedure. 6. The mode LED goes out to indicate after the third number has been found.
ALL OFF-FUNCTION To switch off all programmed devices you can use the ALL OFF- Function: 1. Shortly press the ALL OFF button. The device selected will turn off. 2. Immediately press the ALL OFF button a second time and hold it for 3 seconds. All programmed devices will now be turned off. TV VOLUME/MUTE PUNCH-THROUGH The TV Volume/Mute punch-through feature allows the User to control the Volume and Mute function of their Television in any Mode programmed to be a VCR, DVD) or SAT library device without the need to change to TV Mode. This feature is also available if AUX Mode is programmed to control a second VCR or SAT device. The respective Mode LED must illuminate to show current Mode e.g. if in VCR Mode and volume key is pressed then the TV Mode LED will illuminate. For individual volume control of SAT-devices you can switch OFF/ON this functions as follows: 1. Press the TV button 2. Press and hold the SETUP button for 3 seconds. The LED will light up continually after blinking. 3. Release SETUP button. 4. Press and hold MUTE button for about 8 seconds until the LED lights up again. TOGGLE FUNCTION This feature allows the user by pressing the P<P button to toggle between two previously stored key sequences containing program numbers*: 1. Switch on the device you want to operate (TV, VCR, etc.) 2. Press and hold SETUP button for 3 seconds. The LED will light up continually after blinking. 3. Release SETUP button. 4. Press once the P<P button. 5. Enter the first key sequence (e.g. TV, 1, 2) beginning with a mode key. 6. Press the P<P button again. 7. Enter now the second key sequence (e.g. CD,2). 8. Press the P<P button a last time The P<P key now toggles between TV 12 and CD 2 *max. 4 keys, first key has to be MODE key.

AUTO ZAPPING In TV Mode the stored programs will be shown successively after pressing the Videoplus button once.To finish the function press once the PROG- button.
SHIFT FUNCTION Press and release (normal keypress) the SETUP button followed by the desired secondary function button. If no button is pressed after the SETUP button the remote will time-out to normal (non-shifted) operation after 15-20 seconds.