Reviews & Opinions
Independent and trusted. Read before buy Packard Bell Easynote E2316!

Packard Bell Easynote E2316

Manual

Download (English)
Packard Bell Easynote E2316 Laptop & Notebook, size: 3.6 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Packard Bell Easynote E2316Packard Bell EASYNOTE E2316 Laptop LCD Screen 15.4" WXGA CCFL Single (SUBSTITUTE Replacement LCD Screen ONLY. Not A Laptop ) E2316-13363-LCD
and RESOLUTION before you purchase this item - because some laptop models come with more than one type of screens

Details
Brand: PACKARD BELL
Part Number: E2316-13363-LCD
UPC: 022099229087

 

[ Report abuse or wrong photo | Share your Packard Bell Easynote E2316 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

Packard Bell EasyNote SJ Disassembly Manual

Table of Contents

Overview..... 2 Technician Notes.... 2 Disassembly..... 2 Reassembly..... 2 Required Tools..... 2 Hazardous Voltage.... 3 Avoid Electrostatic Discharge.... 3 Power Supply Unit.... 3 Battery..... 4 Hard Disk Drive.... 4 Memory..... 6 Wireless LAN Adapter.... 7 CPU and CPU Fan.... 7 Keyboard..... 9 Optical Disk Drive.... 10 Button Board..... 11 Top Cover.... 12 HDD Board..... 14 ODD Board..... 15 Speakers..... 16 Subwoofer.... 16 Touchpad Button Board.... 17 Standby Switch..... 17 Modem Board..... 18 RJ11 Connector.... 18 Bluetooth Module.... 19 Bluetooth Antenna..... 20 Main Board..... 21 LCD Panel Assembly.... 22 LCD Bezel.... 23 LCD Panel..... 24 Inverter Board..... 25 Webcam..... 25 WLAN Antenna..... 26 Notice..... 27

Overview

This document contains step-by-step disassembly instructions for the Packard Bell EasyNote SJ. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Packard Bell reserves the right to make changes to the EasyNote SJ without notice.

Technician Notes

Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.

Disassembly

When disassembling the system unit, follow these general rules: Turn off the power using the power button. Disconnect the adapter. Remove any SD/MMC card, ExpressCard or dummy card from the device. Do not disassemble the system into parts that are smaller than those specified in the instructions. Label all removed connectors; note where the connector goes and in what position it was installed.

Reassembly

Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the casing. Check that everything is properly installed and tightened.

Required Tools

All disassembly procedures can be performed using the following tools: Small Phillips and flat-blade screwdriver. Hex-bolt #5 screwdriver

Hazardous Voltage

There is hazardous voltage present inside the notebook when it is connected to an AC supply, even when the notebooks power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)installation of optional hardware devices.
WARNING Ensure that the notebook is disconnected from its power source and from all telecommunications links, networks, or modem lines whenever the casing cover is removed. Do not operate the notebook with the cover removed. AVERTISSEMENT Assurez-vous que le systme est dbranch de son alimentation ainsi que de toutes les liaisons de tlcommunication, des rseaux, et des lignes de modem avant denlever le capot. Ne pas utiliser le systme quand le capot est enlev. WARNUNG Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehuseabdeckung entfernt wird. Nehmen Sie das System nicht ohne die Abdeckung in Betrieb. ADVERTENCIA Asegrese de que cada vez que se quite la cubierta del porttil, el sistema haya sido desconectado de la red de alimentacin y de todos lo enlaces de telecomunicaciones, de red y de lneas de mdem. No ponga en funcionamiento el sistema mientras la cubierta est quitada. WAARSCHUWING Zorg er voor dat alle verbindingen van en naar de notebook (stroom, modem, netwerk, etc) verbroken worden voordat de behuizing geopend wordt. Zet de notebook nooit aan als de behuizing geopend is. AVVERTENZA Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dallalimentazione, da tutti i collegamenti di comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coperchio.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage, store them in protective packaging whenever they are not installed in the system. Add-in cards can be extremely sensitive to ESD and always require careful handling. After removing the card from the notebook, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface. Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure the notebooks power switch is OFF. Then, unplug the notebooks AC power cord. Before picking up the device you (un)install, you should wear an anti-static wrist wrap (available at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the notebook casing. As an alternative, you can dissipate electrostatic buildup by touching an unpainted metal portion of the notebook casing with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the notebook.

Power Supply Unit

Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user-serviceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. Always return a defective power supply to the dealer.

Battery

Perform the following steps to remove the battery: 1. Make sure the power is off. 2. Turn the notebook upside down.
Note: Use an anti-static mat or something soft like a piece of cloth underneath the notebook to prevent damage to the exterior of the notebook.
3. Push the 2 locks outwards to the release the battery. 4. Slide the battery out of the compartment.
Fig. 1 Removing the battery.

Hard Disk Drive

To remove the hard disk drive, first remove the battery (see Battery) and then perform the following steps: 1. Remove the 2 screws on the hard disk drive cover and remove the cover.
Fig. 2 Removing hard disk drive cover.
2. Pull the hard disk drive towards you to disconnect the drive.
Fig. 3 Disconnecting and removing hard disk drive(s).
3. Take the drive out of its compartment as shown in Fig. 3. 4. Remove the 2 screws on the metal bracket to separate it from the hard disk drive.
Fig. 4 Location of hard disk drive bracket screws.
Note: The EasyNote SJ uses S-ATA hard drives exclusively. S-ATA hard drives have no jumpers and need no specific configuration settings to work in a system with multiple hard drives.
Note: The hard drive bays are numbered in the casing (HDD1 and HDD2). The number of the bay corresponds with the sequence in the BIOS: the hard disk drive in bay 1 should be labelled HDD1 in the system BIOS.
Note: If the system ships with 2 hard drives, they will be configured as 2 separate drives and not in any type of RAID configuration.

Memory

To remove the memory installed, first remove the battery (see Battery) and then perform the following steps:
Remove the 7 screws retaining the memory/CPU/WLAN cover and remove the cover.
Fig. 5 Removing memory/CPU/WLAN cover.
Release the metal clips securing the memory module; the module will eject upwards. Carefully remove the module.
Fig. 6 Removing memory module.
Note: In case two memory modules are installed, you always have to remove the top module first before you can remove the second one.

Wireless LAN Adapter

To remove the wireless LAN adapter, first remove the battery (see Battery) and then perform the following steps: 1. Remove the 7 screws retaining the memory/CPU/WLAN cover (see Fig. 5). 2. Carefully disconnect the 2 wireless antenna cables. Take note of which coloured wire is connected to which connector on the adapter.
Fig. 7 Location of antenna cable connectors and screws.
3. Remove the 2 screws securing the wireless LAN adapter (see Fig. 7); the adapter will eject upwards. 4. Take out the wireless LAN adapter from the slot.

CPU and CPU Fan

To remove the CPU, first remove the battery (see Battery) and then perform the following steps: 1. Remove the 7 screws retaining the memory/CPU/WLAN cover (see Fig. 5). 2. Remove the 3 screws holding the CPU fan.
Fig. 8 Location of CPU fan screws.
3. Disconnect the power cable and remove the CPU fan (see Fig. 8). 4. Turn the 6 screws securing the heat sink halfway loose in designated order.
Fig. 9 Location of heat sink screws.
5. Now remove the 6 screws, again in designated order. 6. Carefully remove the heat sink. 7. Turn the screw in the CPU socket 180 degrees counter-clockwise to release the CPU.

Fig. 10 Removing CPU.

8. Take out the CPU.

Keyboard

To remove the keyboard, first remove the battery (see Battery) and then perform the following steps: 1. Turn the notebook over so the top is facing up and open the LCD completely. 2. Release the cover by lifting it a bit near the USB ports on the right side of the notebook and tilt the cover backwards from right to left.
Fig. 11 Removing keyboard cover.
3. Tilt the cover from the front to the back and lift it out (see Fig. 11). 4. Remove the 2 screws securing the keyboard.

1010101010

Fig. 12 Location of keyboard screws.
5. Tilt the keyboard gently forward (see Fig. 12). 6. Before removing the keyboard entirely, carefully release the clip securing the flat cable and disconnect the cable from the main board.
Fig. 13 Disconnecting keyboard flat cable.

Optical Disk Drive

To remove the CD-ROM or DVD drive, first remove the keyboard cover (see steps 1 to 3 in Keyboard), and then perform the following steps: 1. 2. 3. 4. Remove the screw (marked ODD) securing the optical disk drive (see Fig. 13). Use the emergency eject hole to open the optical disk drive. Take out the optical disk drive from the drive bay. Remove the 2 screws securing the metal bracket and remove it from the drive.
Fig. 14 Removing metal bracket.
5. Release the tray cover on one side of the tray.

1111111111

Fig. 15 Releasing tray cover (side).
6. Next release the tray cover on the bottom of the drive.
Fig. 16 Releasing tray cover (bottom).
7. Remove the cover and close the tray!

Button Board

The button board contains the power button, the ECO and WiFi button, and the status LEDs. To remove the button board, remove the keyboard cover (see steps 1 to 3 in Keyboard), and then perform the following steps: 1. Remove the 2 screws securing the button board

1212121212

Fig. 17 Location button board screws.
2. Carefully disconnect the flat cable from the main board (see Fig. 17). 3. Lift out the button board. 4. Disconnect the flat cable from the button board.
Fig. 18 Disconnecting flat cable.

Top Cover

To remove the top cover, remove the hard disks (see Hard Disk Drive), remove the optical disk drive (see Optical Disk Drive), remove the LCD panel assembly (see LCD Panel Assembly), and then perform the following steps: 1. Carefully disconnect the speaker cables connector near the palm rest at the right.

1313131313

Fig. 19 Location of speaker cables connector.
2. Disconnect the standby-switch cable.
Fig. 20 Disconnecting standby-switch cable.
3. Disconnect the touchpad cable.
Fig. 21 Disconnecting touchpad cable.

1414141414

4. Disconnect the button board flat cable (see Fig. 17). 5. Remove the 7 screws securing the cover.
Fig. 22 Location of top cover screws.
6. Turn the notebook upside down. 7. Remove the 13 screws (all M2.5x6).
Fig. 23 Location of top cover screws underside.
8. Turn the notebook upside down and remove the top cover.

HDD Board

The HDD board contains the two Serial ATA connectors. To remove the HDD board, first remove the top cover (see Top Cover), and then perform the following steps:

1515151515

1. Remove the 2 screws securing the HDD board.
Fig. 24 Location of HDD board screws.
2. Lift out the HDD board (it has been clicked onto the main board).

ODD Board

The ODD board extends the IDE connector for the optical drive from the main board. To remove the ODD board, first remove the top cover (see Top Cover), and then perform the following steps: 1. Remove the screw securing the ODD board.
Fig. 25 Location of ODD board screw.
2. Take the ODD board aside and disconnect it from the main board. 3. Remove the ODD board.

1616161616

Speakers
To remove the speakers, first remove the top cover (see Top Cover), and then perform the following steps: 1. Remove the screws securing each speaker.
Fig. 26 Location of speaker screws.
2. Release the speaker cables from the clips and remove any tape holding the cables.
Note: The speakers can only be exchanged as a pair.

Subwoofer

To remove the subwoofer, first remove the top cover (see Top Cover), and then perform the following steps: 1. Disconnect the subwoofer cable from the main board (see Fig. 27-A).
Fig. 27 Location of subwoofer and cable.

1717171717

2. Remove the 2 screws securing the subwoofer and lift it out (see Fig. 27-B).
Note: The subwoofer is optional.

Touchpad Button Board

The touchpad button board is located on the top cover. To remove it, first remove the top cover (see Top Cover), and then perform the following steps: 1. Release the clip securing the flat cable (the clip folds up) and disconnect the flat cable from the touchpad.
Fig. 28 Removing touchpad button board and cable.
Remove the 2 screws securing the touchpad button board and lift out the board including the cable (see Fig. 28).
Note: The touchpad is part of the top cover and it cannot be exchanged separately. You cannot remove the flat cable from the touchpad button board.

Standby Switch

The standby switch works as a soft power switch when the lid is closed; it is located in the top cover. To remove the standby switch, first remove the top cover (see Top Cover), and then perform the following steps: 1. Remove the screw securing the standby switch.

1818181818

Fig. 29 Location of standby switch screw.
2. Clear the cable and remove the standby switch.

Modem Board

To remove the modem board, first remove the top cover (see Top Cover), and then perform the following steps: 1. Remove the 2 screws securing the modem (see Fig. 30-A).

Fig. 30 Location of standby switch screw.
2. Take out the modem; it has been clicked onto the main board. 3. Disconnect the cable from the modem.

RJ11 Connector

To remove the RJ11 connector, first remove the top cover (see Top Cover), and then perform the following steps:

1919191919

1. Disconnect the modem cable from the main board (see Fig. 30-B). 2. Remove the screw securing the RJ11 connector bracket.
Fig. 31 Location of RJ11 connector bracket screw.
3. Take out the RJ11 connector and cable.
Fig. 32 Removing RJ11 connector.
Note: You may need to remove the HDD board (see HDD Board) and/or the ODD board (see ODD Board) to get enough clearance for the cable.

Bluetooth Module

To remove the Bluetooth module, first remove the top cover (see Top Cover), and then perform the following steps: 1. Disconnect the antenna and the cable from the Bluetooth module.

2020202020

Fig. 33 Disconnect Bluetooth antenna and cable.
2. Remove the screw securing the Bluetooth module.
Fig. 34 Location of Bluetooth module screw.
3. Remove the Bluetooth module.
Note: Bluetooth is optional.

Bluetooth Antenna

To remove the Bluetooth antenna, first remove the top cover (see Top Cover), and then perform the following steps: 1. Disconnect the antenna from the Bluetooth module (see Fig. 33). 2. Remove the Bluetooth antenna; it has been glued onto place.

2121212121

Fig. 35 Removing Bluetooth antenna.

Main Board

To remove the main board, remove the CPU and the CPU fan (see CPU and CPU Fan), remove the memory (see Memory), remove the wireless LAN adapter (see Wireless LAN Adapter), remove the HDD and ODD boards (see HDD Board and ODD Board), remove the modem board (see Modem Board), and then perform the following steps: 1. Remove the 7 screws (marked with an arrow) securing the main board.
Fig. 36 Location of main board screws.

2. 3. 4. 5.

Remove the 2 hex bolts adjacent to the DVI-I connector. Lift up the main board. Disconnect the Bluetooth cable (optional). Lift the main board out and turn it upside down.

2222222222

6. Disconnect the RTC battery cable and remove the RTC battery; it has been glued onto place.
Fig. 37 Location of RTC battery.

LCD Panel Assembly

To disassembly the LCD panel assembly, first remove the keyboard (see Keyboard), remove the CPU cover (see step 1 in CPU and CPU Fan), remove the wireless LAN antenna (see step 2 in Wireless LAN Adapter), and then perform the following steps: 1. Remove the LCD cable cover. 2. Disconnect the 3 LCD cable connectors.
Fig. 38 Disconnecting LCD cable connectors.
3. Pull the wireless LAN antenna cables through the base and clear them from the clips (see Fig. 38). 4. Remove 2 screws from the back panel of the notebook.

2323232323

Fig. 39 Location of screws on back panel.
5. Remove 2 screws from the bottom of the notebook.
Fig. 40 Location of screws.
5. Open the LCD panel to a 90-degree angle and lift out the LCD panel assembly.

LCD Bezel

To remove the LCD bezel, first remove the LCD panel assembly (see LCD Panel Assembly), and then do the following: 1. Remove the 4 rubber stoppers from the upper part and 2 stoppers from the lower part of the LCD bezel.
Fig. 41 Location of stoppers/screws securing LCD bezel.
2. Remove the 6 screws (that were covered by the stoppers) securing the LCD bezel. 3. Remove the LCD bezel; it has been clicked into place.

2424242424

LCD Panel
To remove the LCD panel, first remove the LCD bezel (see LCD Bezel), and then do the following: 1. Remove the 4 screws from the hinges.
Fig. 42 Location of screws securing hinges.
2. Disconnect both cables from the inverter board.
Fig. 43 Disconnecting cables from inverter board.
3. Remove the screw securing the grounding cable.

2525252525

Fig. 44 Removing grounding cable screw.
4. Lift out the panel. 5. Remove the 4 screws on each side securing the brackets for the panel.
Fig. 45 Location of screw securing brackets.

6. Push the clips to disconnect the LCD cable from the back of the panel.

Inverter Board

To remove the inverter board, first remove the LCD bezel (see LCD Bezel), and then do the following: 1. Disconnect both cables from the inverter board (see Fig. 43). 2. Remove the screw securing the inverter board and extract the board; it may be glued onto place.

Webcam

To remove the webcam, first remove the LCD bezel (see LCD Bezel), and then do the following: 1. Disconnect the cable from the webcam.

2626262626

Fig. 46 Location of webcam connector.
2. Lift out the webcam; it may be glued and/or taped onto place.
Note: You have to remove the LCD panel if the webcam cable needs to be replaced.

WLAN Antenna

To remove the wireless antenna, first remove the LCD panel (see LCD Panel), and then do the following: 1. The wireless LAN antenna has been glued onto place, loosen both.
Fig. 47 Location WLAN antenna cables.
2. Remove the webcam (see Webcam) to clear the cable of the antenna on the left 3. Release the cable from the clips in the shielding foil.

2727272727

Notice
The information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V.
PACKARD BELL B.V. SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
Copyright 2007 Packard Bell B.V. All rights reserved. Packard Bell is a trademark of Packard Bell B.V. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners.
The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.
EasyNote SJ Disassembly Manual

Author: Wouter Willemse & Juan M. Calvio First Edition: September 2007 Version: 1.0 Part Number: 7434820000 Packard Bell B.V. www.packardbell.com

doc1

Packard Bell EasyNote L Disassembly Manual

Table of Contents

Overview Technician Notes Disassembly Instructions Reassembly Instructions Required Tools Hazardous Voltage Avoid Electrostatic Discharge Power Supply Unit Removing the Battery Removing the Memory Module Removing the Hard Disk Drive Removing the Keyboard Removing the Optical Disk Drive Removing the LCD Module Removing the LCD Panel Removing the CPU Removing the Top Cover Removing the Touchpad Removing the Chipset Heat Sink Removing the WLAN Card Removing the MDC Modem Removing the Main Board Notice 16

Overview

This document contains step-by-step service instructions for the EasyNote L. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Packard Bell reserves the right to make changes to the EasyNote L without notice.

Technician Notes

Only technicians authorized by NEC Computers International B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.

Disassembly Instructions

When disassembling the system unit, follow these general rules:
Turn off the power and disconnect all cables and peripherals. Label all removed connectors. Note where the connector goes and in what position it was installed. Do not disassemble the system into parts that are smaller than those specified in the instructions.

Reassembly Instructions

Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the casing. Check that everything is properly installed and tightened.

Required Tools

All disassembly procedures can be performed using the following tools:

n n n n n

PH 0 x 40 Philips screwdriver 4.0 x 60 Flat-bladed screwdriver 2.0 x 30 Flat-bladed screwdriver SW 5.0 Spacer screwdriver Small tweezers

Hazardous Voltage

There is hazardous voltage present inside the computer when it is connected to an AC supply, even when the computer power switch is off. Exposure to s hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)installation of optional hardware devices.
WARNING Ensure that the computer is disconnected from its power source and from all telecommunications links, networks, or modem lines whenever the casing cover is removed. Do not operate the computer with the cover removed. AVERTISSEMENT Assurez-vous que le systme est dbranch de son alimentation ainsi que de toutes les liaisons de tlcommunication, des rseaux, et des lignes de modem avant d enlever le capot. Ne pas utiliser le systme quand le capot est enlev. WARNUNG Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehuseabdeckung entfernt wird. Nehmen Sie das System nicht ohne die Abdeckung in Betrieb. ADVERTENCIA Asegrese de que cada vez que se quite la cubierta del chasis, el sistema haya sido desconectado de la red de alimentacin y de todos lo enlaces de telecomunicaciones, de red y de lneas de mdem. No ponga en funcionamiento el sistema mientras la cubierta est quitada. WAARSCHUWING Zorg er voor dat alle verbindingen van en naar de computer (stroom, modem, netwerk, etc) verbroken worden voordat de behuizing geopend wordt. Zet de computer nooit aan als de behuizing geopend is. AVVERTENZA Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dall alimentazione, da tutti i collegamenti di comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coperchio.

Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage, store them in protective packaging whenever they are not installed in your system. Add-in cards can be extremely sensitive to ESD and always require careful handling. After removing the card from the computer, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface. Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure your computer power switch is OFF. Then, s unplug the computer AC power cord. Before picking s up the device you (un)install, you should wear an antistatic wrist wrap (available at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the computer casing. As an alternative, you can dissipate electrostatic build-up by touching an unpainted metal portion of the computer casing with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the computer.

Power Supply Unit

Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user-serviceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. Always return a defective power supply to your dealer.

Removing the Battery

Perform the following steps to remove the battery: i. ii. iii. iv. Make sure to power off the EasyNote L. Disconnect the AC adapter and all peripherals. Turn the unit over. Unlock the battery and slide it out.
Fig. 1 Releasing the battery.
Removing the Memory Module
To remove the memory module, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screw securing the memory compartment cover.
Fig. 2 Memory compartment cover screw location. ii. Release with your fingers the side locks located on the memory slot. As you release the locks, the module will automatically pop up and stay in a 45 angle position.

Fig. 3 Releasing the memory side locks. iii. Pull out the memory module from its slot.
Removing the Hard Disk Drive
To remove the hard disk drive, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the 2 screws securing the hard disk drive compartment cover.
Fig. 4 Removing the hard disk drive cover. 2. Remove the 2 screws that secure the hard disk drive. 3. Carefully pull the Mylar to slide the hard disk drive assembly out of the bay.
Fig. 5 Removing the HDD assembly.

Removing the Keyboard

To remove the keyboard, first remove the battery (see Removing the Battery), then perform the following steps:
1. Release the keyboard cover from the rear of the notebook.
Fig. 6 Releasing the keyboard cover. 2. Open the notebook and tilt the LCD module entirely backward. 3. Carefully remove the keyboard cover.
Fig. 7 Lifting the keyboard. 4. Pull the keyboard up with your fingertips. Be careful not to break the keyboard locks. Since the keyboard is connected to the computer through a flat cable, your have to be careful to not break this cable. 5. With the keyboard lying on top of the palm rest, disconnect the keyboard flat cable from the unit (see Fig. 8). To do so: i. Set the flat cable connector on the main board in the unlocked position (#1, Fig. 9). ii. Remove the keyboard cable from the keyboard connector on the main board (#2, Fig. 9).
Fig. 8 Disconnecting the keyboard flat cable.
Fig. 9 Disconnecting the flat cable.
Removing the Optical Disk Drive
To remove the optical disk drive, first remove the battery (see Removing the Battery) and remove the keyboard (see Removing the Keyboard), then perform the following steps: 1. Remove the 2 screws securing the optical disk drive.
Fig. 10 Releasing the optical disk drive. 2. Flip over the unit, open the LCD and push the optical disk drive module out from the base unit.
Fig. 11 Pushing the optical disk drive out.

Removing the LCD Module

To remove the LCD module, first remove the battery (see Removing the Battery), remove the keyboard (see Removing the Keyboard), then perform the following steps: 1. Remove the 6 screws securing the heat plate.
Fig. 12 Removing the heat plate screws. 2. Close the LCD, flip over the notebook and remove the 2 screws securing the LCD module.
Fig. 13 Removing the LCD module screws (bottom). 3. Remove the 2 screws on the back.

Fig. 14 Removing the LCD module screws (rear). 4. Open up the LCD and gently disconnect the LCD power cable and the 2 WLAN antenna cables.
Fig. 15 Location WLAN antenna cables and LCD power cable.
The black WLAN antenna cable is on the MAIN connector, the grey one on the AUX connector.
5. Carefully lift the LCD module away from the unit.

Removing the LCD Panel

To remove the LCD panel, first remove the LCD module (see Removing the LCD Module), then perform the following steps: 1. Use a pin to remove the rubber covers on the LCD module.
Fig. 16 Location of rubber covers and screws. 2. After removing the rubber covers, remove the screws and release the LCD cover carefully. 3. Remove the inverter board after unscrewing the screw and disconnecting all connectors.
Fig. 17 Removing the inverter board. 4. Carefully lift the LCD panel. 5. Remove the screws on both sides of the LCD panel in order to release the LCD hinges.
Fig. 18 Removing the LCD panel hinges.

Removing the CPU

To remove the CPU first remove the battery (see Removing the Battery) and remove the keyboard (see Removing the Keyboard), then perform the following steps:
1. Remove the screws securing the heat plate (see Fig. 12). 2. After taking out the heat plate, remove the 3 CPU fan screws, disconnect the CPU fan connector and remove the CPU fan.
Fig. 19 Location CPU fan screws. 3. Remove the 3 remaining screws on the CPU heat sink and take it out.
Fig. 20 Location remaining CPU heat sink screws. 4. Unlock the CPU socket by turning captured screw head fully counter clockwise with a flatbladed screwdriver.
Fig. 21 Removing the CPU.
5. Take out the CPU very carefully.
Note Beware of the screws you use on the CPU heat sink! Make sure to use the original screws, otherwise it might cause damage to the CPU die.
Use extra care when unlocking or locking the CPU socket because the screwdriver might cause damage on CPU edge each time when unlocking or locking the CPU socket. s

Removing the Top Cover

To remove the top cover, first remove the battery (see Removing the Battery), remove the hard disk drive (see Removing the Hard Disk Drive), remove the optical disk drive (see Removing the Optical Disk Drive), remove the keyboard (see Removing the Keyboard) and remove the LCD module (see Removing the LCD Module), then perform the following steps: 1. Remove all screws (2 small and 8 larger ones) on the bottom of the base unit.
Fig. 22 Location bottom cover screws. 2. Flip over and open up the notebook completely so that the LCD is levelled with the bottom of the casing. 3. Release all screws (2 large and 3 smaller ones) on the top cover.

Fig. 23 Location top cover screws. 4. Disconnect the touchpad connector and remove the flat cable (same principle as described in Fig 9).
Fig. 24 Disconnecting the touchpad cable. 5. Carefully lift the top cover.

Removing the Touchpad

To remove the touchpad, first remove the top cover (see Removing the Top Cover), then perform the following steps: 1. Remove the screws securing the touchpad to the top cover.
Fig. 25 Location touchpad screws. 2. Carefully separate the touchpad module from the top cover.
Removing the Chipset Heat Sink
To remove the chipset heat sink, first remove the top cover (see Removing the Top Cover), then perform the following steps: 1. Remove the 2 screws securing the chipset heat sink to the main board.
Fig. 26 Location chipset heat sink screws.

Removing the WLAN Card

To remove the WLAN card, first remove the LCD module (see Removing the LCD Module) and then perform the following steps: 1. Release with your fingers the side locks securing the WLAN card. As you release the locks, the card will automatically pop up and stay in a 45 angle position.
Fig. 27 Releasing the WLAN side locks. 2. Carefully take out the WLAN card from the slot.

Removing the MDC Modem

To remove the modem, first remove the top cover (see Removing the Top Cover), then perform the following steps: 1. Remove the 2 screws securing the modem to the main board.
Fig. 28 Location modem card screws. 2. Turn over the modem and gently disconnect the MDC cable.

Removing the Main Board

To remove the main board, first remove the top cover (see Removing the Top Cover) and then perform the following steps: 1. Remove the hex screws from the VGA port. 2. Remove all screws on the HDD holder and separate it carefully from the main board.
Fig. 29 Screw location on the HDD holder. 3. Disconnect the speaker and Lid switch connectors from the main board and remove the screws encircled in the following picture.
Fig. 30 Screws and connectors on main board. 4. Lift the main board and remove it away from the unit.
Fig. 31 Removing the main board.

Notice

The information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International B.V. NEC COMPUTERS INTERNATIONAL B.V. SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
Copyright 2005 NEC Computers International B.V. All rights reserved. Packard Bell is a trademark of NEC Computers International B.V. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners. The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.

EasyNote L Disassembly Manual
Author: Juan M. Calvio & Thomas Herbers - ECCS First Edition: October 2005 Document Part Number: 7400360000 Version: 1.0 Packard Bell A division of NEC Computers International B.V.

 

Tags

Oxygen 88 PC-1248 RS-DC10 KV-25X5B Gigaset SL56 Series Handheld PC System HD322GJ MKB-1000 TX-32PX10F Eurv 6 F100DB DVX9900H BSG71370UC SA-608 Stylus-9000 SL-CT520 Samsung I600 SGH-C161 ADC67555W 78-9518 S2110 Models SD-2200 Qtek S200 CCD-TRV300E PS50B850y1W Dockstar DSC-H3 26000 AX-300 Microtower PC Eu R08 SM1960 PSC 1350 W-800 MTB-8 WN-200R MPU-101 Grinder UX-BD80 CR 2510 Pentax MZ-S Family GR-D225EK P5K SE VS 540 1050EP Nikon D2H Controllermodulescards LAV30-50 F350-2007 28PW6324 58R PDX-5 FP735 KRC-379R Quest KD-G320 KC 450 XVC20E VP-DX205 KX-TC1750B SV6003H DCT5100 MZ-NH600 Recon Rxl 70 SGH-E250D VE-gspro 32PF9966 WAG102 XM-222 Wintv Breadmaker 29PT5324 58R KDL-40EX400 G-1000DXA Compact 4000 Motorola H550 SCC-C6407P Coupe FM33 4G DEH-2750 111SC C-310 Zoom Na-ittl RS-X933 9 DCI RA201 EG008W NAD C440 7802 DTM CLD-2950 32PFL5605H 9500 MPR E808Y DP-33F J300I MEH-P9100R

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101