FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMP POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) ANTENNA LEAD WIRE
NEC NATIONAL ELECTRICAL CODE

S2898A

14. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges. 15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product. 18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or damaged in any way. f. When the video product exhibits a distinct change in performance this indicates a need for service. 20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 22. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

INDICE

I CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES. 35 I CAMBIO DE VCR/DVD. 38 I CONEXIONES. 39 DVD/VCR A CONEXIN DE TV. 39 CANAL DE SALIDA RF. 39 CONECTANDO A UN TV. 39 CONECTANDO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VDEO o TOMAS DE ENTRADA DE VDEO COMPONENTE. 39 CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT. 39 CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY. 39 CONECTANDO A UN AUDIO ANALGICO. 39 I PREPARACIN. 39 PREPARACIN DE CANAL AUTOMTICA. 39 PREPARACIN DE RELOJ. 40 I REPRODUCCIN DE UN DISCO. 40 REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO. 40

Page 6

FEATURES

DVD Mode

Dolby Digital sound Virtual Surround Component Video Out Jacks
This DVD/VCR COMBINATION UNITS can handle Dolby Digital surround sound with 5.1 channels when connected to a Dolby Digital decoder. Still/fast/slow/step playback Random playback for audio CD and MP3 Program playback for audio CD and MP3 DVD menus in a desired language Screen saver/Auto power-off functions The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program is activated for 30 minutes, the power is automatically turned off. Subtitles in a desired language Selecting a camera angle Choices for audio language and sound mode Parental lock Automatic detection of discs This player automatically detects if the loaded disc is DVD, audio CD or MP3 on disc. Playing an MP3 disc Direct Search On-screen display Information about the current operation can be displayed on the TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control. Search Chapter search / Title search / Track search / Time search Repeat Chapter / Title / Track / Group / All / A-B Zoom Marker The part designated by user can be called back. Resume Play
Jacks located on the back of the DVD/VCR COMBINATION UNITS which are used to send high-quality video to a TV via Component Video In Jacks. Bit rate indication DRC (Dynamic range control) You can control the range of sound volume. Black Level Setting

VCR Mode

Hardware specifications
Auto Head Cleaner Trilingual on-screen menu display selectable in
English, French, or Spanish 181 channel capability PLL frequency synthesizer tuner with direct station call (A cable converter box may be necessary to view scrambled cable channels.)

Automatic functions

Auto power on system
Automatically turns the VCR on when you insert the cassette. Digital Auto Tracking (DTR)

Playback

Auto Repeat 2 Step Picture Search Operation Index Search Time Search

Recording

1 Year, 8 events (including Daily and Weekly Timer

* Depending on the types or the writing method of the medium some discs can not be played. Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs made on personal computers, or on DVD recorders may not be played back properly due to factors such as scratches, dirt or special properties of the disc. Discs made on personal computers may not be played back properly due to different environments or the settings of the application you use. We recommend always to use the standardized, properly formatted discs. (Please contact the sales agency for more detail). This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as PAL or SECAM. Some discs include region codes as shown below.

Example

Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
[AUDIO CD] Data on an audio CD is divided into sections called tracks, each of which is given a track number.
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format can only be played back on DVD/VCR COMBINATION UNITS with the same region code. The following discs cannot be played back on this DVD/VCR COMBINATION UNITS.
DVD with region codes other than 1 or ALL. DVD-ROM DVD-RAM (Never play back, otherwise malfunc-
[MP3] Data on an MP3 is divided into sections called "groups", and then into subsections called "tracks", each of which is given a group or track number.

Group 1

Track 1 Track 2 Track 3 Track 4

Group 2

Track 1 Track 2

tion may result.)

CD-ROM VSD CDV (Only plays back the audio part.) CD-G (Only plays back the sound.) CD-I (Never play back, otherwise malfunction

may result.)

SACD Photo CD (Never play back, otherwise malfunc-
Video CD (Never play back, otherwise malfunc-
Any other discs without compatibility indications.

Page 8

OPERATING CONTROLS AND FUNCTIONS

FRONT PANEL

REMOTE CONTROL
DISPLAY DVD POWER SPEED AUDIO

SKIP/CH. VCR/TV

VCR PAUSE

RECORD

ENTER SETUP TITLE

SEARCH MODE

RETURN

CLEAR/ C.RESET

SUBTITLE ANGLE REPEAT
1. Disc loading tray 2. OPEN/CLOSE Button [page 22] Press to insert discs into or remove them from the tray. 3. DVD OUTPUT Light (Green) [page 12] This light appears when the DVD output mode is selected. You can only watch DVDs when the green DVD OUTPUT light is on. To make the green DVD OUTPUT light come on, press DVD on the remote control or OUTPUT on the front panel. 4. VCR OUTPUT Light (Green) [page 12] This light appears when the VCR output mode is selected. You can only watch tapes when the green VCR OUTPUT light is on. To make the green VCR OUTPUT light come on, VCR on the remote control or OUTPUT on the front panel. 5. CASSETTE COMPARTMENT

6. POWER Button [page 16] Press to turn the power on and off. 7. POWER Light (red) Light appears when the power is on. 8. STOP/EJECT Button (VCR) EJECT Button Press to remove the tape from the VCR. STOP Button Press to stop the tape motion. 9. PLAY Button(VCR) [page 18] Press to begin playback. 10. CH(ANNEL) Buttons [page 16] In VCR mode, press to change TV channels on the VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture. 11. AUDIO In Jack [page 21] Connect an audio cable coming from the audio out jack of a camcorder, another VCR, or an audio source here. 12. VIDEO In Jack [page 21] Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source (laser disc player, camcorder, etc.) here. 13. FF Button (VCR) [page 18] Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search). 14. REW Button (VCR) [page 18] Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search). 15. REC Button [page 19] Press once to start a recording. Press repeatedly to start a One-Touch Recording. 16. REC Light [page 19] Light appears during recording. 17. TIMER Light [page 19] Light appears when the DVD/VCR is in standby mode for a timer recording or during a One-Touch Recording. It flashes if T-SET is pressed for a timer recording, but there is no tape in the DVD/VCR. It flashes when all timer recordings or One-Touch Recordings are finished.

Page 9

18. OUTPUT Button [page 12] Press to select DVD mode or VCR mode. G You can switch the output mode either by pressing OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press OUTPUT on the front panel first, you need to re-select the corresponding mode by pressing DVD or VCR on the remote control. 19. Remote Sensor Window 20. DISC IN Light (green) Light appears when a disc is in the DVD Player. 21. PLAY Light (green) Light appears during Disc playback. 22. FWD Button (DVD) [page 23] Press to fast forward the Disc. Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the forward speed of slow motion. Press to skip Chapters or Tracks. 23. PLAY Button (DVD) [page 22] Press to begin playback. 24. REV Button (DVD) [page 23] Press to view the DVD picture in fast reverse motion or to reverse playback of an Audio CD. Press to skip Chapters or Tracks. 25. STOP Button (DVD) [page 22] Stops operation of the disc. 26. SPEED Button [page 19] Press to select the VCRs recording speed (SP or SLP) 27. POWER Button Press to turn the power on and off. 28. Number Buttons G DVD mode [page 24] Press to select numbered items in a menu. +10 Use this button to enter number 10 and above. G VCR mode [page 16] Press to select TV channels on the VCR. To select channels, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 then 6. 29. DISPLAY Button G DVD mode [page 28] Press to access or remove the display screen during DVD or Audio CD playback. G VCR mode Press to access or remove the VCRs on-screen status display. 30. DVD Button [page 12] Press to select DVD mode for the remote control. G You can switch the OUTPUT mode either by pressing OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press OUTPUT on the front panel first, you need to re-select the corresponding mode by pressing DVD or VCR on the remote control. 31. h Button G DVD mode [page 23] Press to view the DVD picture in fast reverse motion. Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the reverse speed of slow motion. G VCR mode [page 18] Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search).

32. STOP Button G DVD mode Press to stop the disc motion. G VCR mode Press to stop the tape motion. 33. RECORD Button [page 19] Press once to start a recording. 34. MENU Button G DVD mode [page 23] Press to display the menu of the Disc. G VCR mode [page 17] Press to access the VCR menu. 35. TITLE Button [page 23] 36. SETUP Button [pages 28-31] Press to enter DVD player setup mode. 37. ZOOM Button [page 24] Enlarges part of a DVD-reproduced image. 38. MODE Button [pages 26,27,and 30] Activates program playback or random playback mode when playing CDs or MP3. Sets Black level and virtual surround. 39. SUBTITLE Button [page 27] Press to select the desired subtitle language. 39. T-SET Button [page 19] Press to put the VCR into standby mode for a timer recording. 40. ANGLE Button [page 27] Press to change the camera angle to see the sequence being played back from a different angle. 41. REPEAT Button [page 25] Repeats playback of the current disc, title, chapter or track. 42. A-B REPEAT Button [page 25] Repeats playback of a selected section. 43. SEARCH MODE Button G DVD mode [page 24] Press to access or remove the Search display, which allows you to go directly to a specific Title/Chapter/Track/Time. G VCR mode [page 18] Press to perform a Time Search or an Index Search. 44. CLEAR/C.RESET Button G DVD mode [pages 24,25] Press to reset the setting. G VCR mode [page 16] Press to reset the counter. Press to exit from the MENU screen. 45. RETURN Button [page 30] G DVD mode Returns to the previous operation. 46. Arrow Buttons Use when making settings while watching the display on a TV screen. G DVD mode [pages 22-31] Moves the cursor and determines its position. G VCR mode [page 16] p/o Buttons Press to enter digits when setting program (For example: setting clock or timer program). Press to select the setting modes from the on screen menu. B Button When setting program (For example: setting clock or timer program), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numEN

Page 10

47. 48.
bers during channel preset. s Button Press to cancel a setting of timer program. Press to correct digits when setting program (For example: setting clock or timer program). Press to add or delete channel numbers during channel preset. ENTER Button G DVD mode [page 22] Press to accept a setting. g Button G DVD mode [page 23] Press to fast forward the Disc. Press PAUSE, then press this button to begin slow motion playback. Press this button repeatedly to change the forward speed of slow motion. G VCR mode [page 18] Press to rapidly advance the tape, or view the picture rapidly in forward during playback (Forward Search). PLAY Button G DVD mode Press to begin playback. G VCR mode Press to begin playback. VCR Button [page 12] Press to select VCR mode for the remote control. G You can switch the OUTPUT mode either by pressing OUTPUT on the front panel, or by pressing DVD or VCR on the remote control. However, if you press OUTPUT on the front panel first, you need to re-select the corresponding mode by pressing DVD or VCR on the remote control.

65. 66.
Audio In jacks of a television or other audio equipment (DVD only). S-VIDEO OUT Jack Connect an optional S-Video cable here and to the SVideo In jack of a television. VIDEO IN Jack Connect a cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.) here. DVD/VCR VIDEO OUT Jack Connect the yellow video cable (supplied) here and to the TVs Video In jack. ANT-OUT (Antenna Out) Jack Use the supplied RF coaxial cable to connect this jack to the ANTENNA IN Jack on your TV.
Notes The S-VIDEO OUT jack, COAXIAL jack, and COM PONENT VIDEO OUT jack are only useful in DVD mode. Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the player.

LOADING THE BATTERIES

1. Open the battery compartment cover. 2. Insert two AA batteries (supplied), with each one oriented correctly. 3. Close the cover. Notes Do not mix alkaline and manganese batteries. Do not mix old and new batteries.

Page 12

VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct output mode.

SWITCHING TO VCR MODE

Press VCR on the remote control. (Verify that the VCR OUTPUT Light is lit.)

SWITCHING TO DVD MODE

Press DVD on the remote control. (Verify that the DVD OUTPUT Light is lit.)
Notes Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need to select the correct mode on the remote control too.

POWER SPEED

SKIP/CH.

VCR/TV

DVD OUTPUT Light DVD button VCR button

DISPLAY

VCR OUTPUT Light

MENU ENTER SETUP TITLE

OUTPUT button

Page 13

HOOKUPS
CAUTION: Be sure to turn off the DVD/VCR COMBINATION UNITS and equipment to be connected before connecting. Read through the operation manual for the equipment to be connected. Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables. Be sure to keep the DVD/VCR COMBINATION UNITS connection cables separate from the TV antenna cable when you install the DVD/VCR COMBINATION UNITS, because it may cause electrical interference when you are watching television programs.

DVD/VCR TO TV CONNECTION

5 Begin channel preset by pressing B once.
The tuner scans and memorizes all active channels in your area. The VCR distinguishes between

CH 01 AUTO SET UP

standard TV channels and cable channels.
6 After scanning, the tuner stops on the lowest memorized channel. The TV screen returns to TV mode. If AUTO SET UP appears on the TV screen again,
check the cable connections. Press B once again and the VCR will begin preset again.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHANNEL (UP/DOWN) or by directly pressing Number on the remote control. Note for using the Number: When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7) You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
1 You need to connect the antenna or cable to
the VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet.
TO PRESET THE CHANNELS AGAIN 1 Press MENU until the main menu appears.
(If you have already set the clock, you only have to press it once. If not, you have to press it twice).
2 Turn on the TV and set the TV to channel 3.
If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See RF OUTPUT CHANNEL on page 13 for the detail.)
2 Select CHANNEL SET UP by pressing K

or L. Then, press B.

3 Turn on the VCR by pressing POWER. the
POWER light will come on.
3 Select AUTO SET UP by pressing K or L.
Then, press B. After scanning, the tuner stops on the lowest memo-
4 Select the On Screen Language (ENGLISH, FRANCAIS or ESPAOL) by pressing K or L. Then, press B.

rized channel.

Page 17

TO ADD/DELETE CHANNELS

When scanning, some channels may be skipped due to a weak signal. In such cases, you can add the channels to the VCR memory manually.

CLOCK SET UP

VCR 1 Select main menu by pressing MENU.
Press MENU until the main menu appears.(If you have already - MENU TIMER PROGRAMMING set the clock, you only have AUTO REPEAT UP [OFF] CHANNEL SET CLOCK SET LANGUAGE SELECT to press it once. If not you AUDIO OUT [ON] TV STEREO SAP have to press it twice).

2 Turn on the TV and set the TV to channel 3. If noise appears, change the RF output channel of

SEARCH FUNCTIONS

VCR PICTURE SEARCH
If you want to skip or repeat a scene during playback, press D or E. Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only).
3 Begin playback by pressing PLAY.
Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback. To adjust the tracking manually, press SKIP/CH. on the remote or CHANNEL (UP/DOWN) on the VCR. When a tape has reached the end, the VCR will rewind the tape to the beginning, and eject the tape.

INDEX SEARCH

An index mark will be assigned at the beginning of each recordings you make. You may skip to a specific marked point by following the steps below.
4 To stop playback, press STOP. If no corresponding symbols appear on the display
when you press buttons such as PLAY, RECORD, D or E, that means no cassette tape is in the VCR. Please insert a tape.
1 Press SEARCH MODE so that the Index

Search menu appears.

2 Enter the number of recordings you wish to
skip by pressing K or L within 30 seconds.

INDEX SEARCH 03

Counter Reset
You can reset the counter by pressing
CLEAR/C.RESET on the remote control twice.

STILL/SLOW

You can freeze the picture on TV screen by pressing PAUSE during playback. You can advance the picture one frame at a time by pressing PAUSE during the Still mode. You cannot manually adjust the tracking of a still picture. However, if the picture begins to vibrate vertically during the still mode, you can stabilize the picture by pressing CHANNEL (UP/DOWN). If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if so equipped. You can watch in the slow motion by pressing SLOW during playback or the still mode. If a noise bar appears on the TV screen, you can reduce it by pressing CHANNEL (UP/DOWN). After the VCR has been in Still/Slow mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage. To return to playback, press PLAY.

3 Press B or { to start index search. If you want to go in the forward direction, press B. If you want to go in the reverse direction, press {. If you want to stop search function, press STOP. After index search, the VCR will play the tape automatically.

TIME SEARCH

This feature allows you to go to a specific point on a tape by entering the exact amount of time you wish to skip in order to reach the point.
1 Press SEARCH MODE 2 times so that the
Time Search menu appears.
2 Enter your desired time to

TIME SEARCH 2 : 50

AUTO REPEAT PLAYBACK
This feature allows you to play a tape over and over.
3 Press B or { to start time search. If you want to go in the forward direction, press B. If you want to go in the reverse direction, press {. If you want to stop search function, press STOP. After time search, the VCR will play the tape automatically.
1 Select main menu by pressing MENU.

Page 19

RECORDING FUNCTION
It may be UNLAWFUL to record copyrighted material without the consent of the copyright owner. Accidental Erasure Prevention To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the Record safety tab hole with cellophane tape.
If a tape ends during OTR, the VCR will stop, eject
the tape, and switch to the DVD mode automatically as the TIMER light blinks. (If the DVD power is off, the VCR will become STANDBY status). When OTR is finished , the VCR turns off automatically. To use the VCR again, press T-SET on the remote, or STOP/EJECT on the DVD/VCR COMBINATION UNITS.
Before recording, make sure:
The desired channel is selected by pressing Number

TIMER RECORDING

You may set the VCR to start recording while you are away. You can set eight programs to record on specific days, daily or weekly within 1 year period.
If you have not yet set the clock, "CLOCK SET" appears. If so, follow the steps [3] and [4] in "CLOCK SET UP" section on page 17. Then, set the timer recording.
on the remote control or CHANNEL (o/p). (If you connected the VCR to a cable box or satellite box as in "DVD/VCR TO TV CONNECTION" on page 13, select channel 3 on your TV. Then, select the channel you want to record with the cable box or satellite box. In this case, you can ONLY record and view the SAME channel.) If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. There is a tape with a safety tab in the VCR. The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing SPEED on the remote control. TV STEREO or SAP is selected.

4 Press Arrow (K/ L) to select the below

items, then press ENTER.

DRC (Dynamic Range Control): To compress the range of sound volume. The default setting is OFF. 29

Page 30

BLACK LEVEL SETTING
Adjust the Black Level Settings to make the black parts of the picture brighter.

DISPLAY SETTING

You can change certain aspects of the DVD display screens, and on-screen messages.
1 Press MODE during playback.
2 Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter. OFF: Shows the original picture as recorded.
3 Press Arrow (s/ B) to select DISPLAY, then
3 Press MODE twice or RETURN to exit.
DISPLAY TV ASPECT 4:3 LETTER BOX ANGLE ICON ON AUTO POWER OFF ON

VIRTUAL SURROUND

DVD-V CD MP3
You can enjoy stereophonic visual space on your existing stereo system.
1 Press MODE twice (CD/MP3: once) during

playback.

2 Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
3 Press MODE or RETURN to exit.
Note (for CD play only) Virtual Surround will not be effective if the sound mode is set to something other than STEREO.
TV ASPECT: QUICK Press Arrow (K/L) for an item selection, then press ENTER. Select 4:3 LETTER BOX for a black bars appears on top and bottom of the screen. Select 4:3 PAN & SCAN for a full height picture with both sides trimmed. Select 16:9 WIDE if a wide-screen TV is connected to the DVD/VCR. The default setting is 4:3 LETTER BOX. ANGLE ICON: Press ENTER repeatedly to turn Angle icon ON or OFF. The default setting is ON. AUTO POWER OFF: Press ENTER repeatedly to turn Auto Power off ON or OFF. The default setting is ON and it will turn the DVD/VCR to off automatically after 35 minutes of no use.

5 Press SETUP to exit.

Notes Be sure to press SETUP, or the setting will not work.

Page 31

LANGUAGE SETTING
Language options are not available with some discs.
AUDIO: Sets the audio language. SUBTITLE: Sets the subtitle language. DISC MENU: Sets the language for DVD menu. PLAYER MENU: QUICK Sets the language for the On-screen display.
5 Press Arrow (K/ L) to select a setting, then
press ENTER. If OTHER is selected on the AUDIO, SUBTITLE or
3 Press Arrow (s/ B) to select LANGUAGE,
then press ENTER to confirm.
DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list below.) Only the languages supported by the disc can be selected.
LANGUAGE AUDIO SUBTITLE DISC MENU PLAYER MENU
ORIGINAL OFF ENGLISH ENGLISH

6 Press SETUP to exit.

Note Language Setting for Audio and Subtitle is not available with some discs. Then use the Audio and the Subtitle button. Details are on page 27.

Notes Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owners Manual for details on correct operations. Playback from a desired track and random playback are not available during program playback.

Page 33

MAINTENANCE

SERVICING

Should your DVD/VCR COMBINATION UNITS

AUTO HEAD CLEANING

Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture. Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR COMBINATION UNITS may need to be cleaned. 1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner. 2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-256-2487 to locate an Authorized Service Center.
become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-256-2487 to locate an Authorized Service Center.

CLEANING THE CABINET

Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.

CLEANING DISCS

When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe in a circular motion. Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.

NOTES:

Remember to read the instructions included with the video head cleaner before use. Clean video heads only when problems occur.

CLEANING THE DISC LENS

If the player still does not perform properly when it
is operated while referring to the relevant sections and to TROUBLESHOOTING GUIDE in this Owners Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

DISC HANDLING

Use discs which have the following logos on them.
(Optical audio digital discs.)
Recordable ReWritable Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
Always store the disc in its protective case when it is

not used.

Make your contribution to the environment!!! Used up batteries do not belong in the dust bin. You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details. 33

Page 34

SPECIFICATIONS
Product type: Discs: DVD player with Video Cassette Recorder DVD video Audio CD Video Cassette tape VHF Channel 3 or 4. 120 V AC +/- 10%, 60 Hz +/- 0.5% 24 W (standby: 7.0 W) 41F (5C) to 104F (40C) W 17-1/8 (435 mm) H 4 (99 mm) D 8-7/10 (218 mm) Weight: 8.8 lbs (3.7 kg)
Converter output: Power source: Power consumption: Operating temperature: Dimensions:
Designs and specifications are subject to change without notice. If there is a discrepancy between languages, the default language will be English.

Page 35

CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES

PANEL DELANTERO

PANEL REMOTO

DISPLAY DVD

1. Bandeja de carga del disco 2. Botn OPEN/CLOSE Presione para insertar discos en o removerlos de la bandeja de disco. 3. Luz DVD OUTPUT (verde) Esta luz aparece cuando el DVD/VCR est en modo DVD. Usted slo puede mirar DVDs cuando la Luz DVD OUTPUT verde est encendida. Para hacer que la Luz DVD OUTPUT verde se encienda, presione el Botn DVD en el control remote o el Botn OUTPUT en el panel delantero. 4. Luz VCR OUTPUT (Verde) Esta luz aparece cuando el DVD/VCR est en el modo VCR. Usted puede slo mirar cintas cuando la Luz VCR OUTPUT verde est encendida. Para hacer que la Luz VCR OUTPUT verde se encienda, presione el Botn VCR en el control remote o el Botn OUTPUT en el panel delantero. 5. CASSETTE COMPARTMENT 6. Botn POWER Presione para conectar y desconectar la alimentacin. 7. Luz POWER (rojo) Se enciende cuando la energa est encendido. 8. Botn STOP/EJECT (VCR) G Botn de expulsin Plselo para sacar el videocasete de la videograbadora. G Botn Stop Presione detener el movimiento de la cinta.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. To locate your nearest Emerson Authorized Service Center or for general service procedure, please call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC. Customer Service 100 North Street; Teterboro, NJ 07608
Tel :1-800-256-2487 http://www.funai-corp.com PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China 0VMN03468 H9410UD #####