TomTom XL

Installation

Whats in the box

a Your TomTom XL

b EasyPortTM holder

c Car charger

d USB cable

e Documentation pack

Before you start

Switching on and off
Install your TomTom XL navigation device in your car following the instructions in the installation section at the start of this book. To switch on your navigation device, press and hold the On/Off button until you see the start-up screen. The first time you switch on your device, it may take a short time to start. To set up your device you need to answer a few questions by tapping the screen.

Device not starting

In rare cases, your TomTom XL navigation device may not start correctly or may stop responding to your taps. First, check that the battery is properly charged. To charge the battery, connect your device to the car charger. It can take up to 2 hours to fully charge the battery. If this does not solve the problem, you can reset the device. To do this, press and hold the On/Off button for 15 seconds and release the button when your device begins to restart.

Charging your TomTom XL

Before you use your XL for the first time, its a good idea to charge it fully. The battery in your TomTom XL navigation device charges when you connect it to the car charger or to your computer. There is no charging light on your XL. To check the battery status and see when your XL is charging, switch on your device and tap the bottom righthand corner of the screen in the Driving View. The battery status is shown on the next page. When you connect your device to a computer, you are asked if you want to connect to the computer. If you select No and then do not tap the screen within three minutes, the device will automatically switch off. This happens so that the battery can charge faster. Note: You should plug the USB connector directly into a USB port on your computer and not into a USB hub or USB port on a keyboard or monitor.

Battery notes

The battery in your TomTom XL navigation device charges when you connect it to the car charger or to your computer. When you connect your device to a computer, you are asked if you want to connect to the computer. If you select No and then do not tap the screen within three minutes, the device will automatically switch off. This happens so that the battery can charge faster. Note: You should plug the USB connector directly into a USB port on your computer and not into a USB hub or USB port on a keyboard or monitor.

GPS reception

When you first start your TomTom XL navigation device, the device may need a few minutes to determine your GPS position and show your current position on the map. In future, your position will be found much faster, usually within a few seconds. To ensure reception of a strong GPS signal, you should use your device outdoors. Large objects such as tall buildings can sometimes interfere with reception.

Take care of your device

Never leave your TomTom XL navigation device or accessories on view when you leave the car or they may become an easy target for thieves. You can set a password for your device which must be entered every time you start it. It is important to take care of your device. Your device is not designed for use in extreme temperatures and any such exposure may cause permanent damage. Do not open the casing of your device under any circumstances. Doing so may be dangerous and will invalidate the warranty. Wipe or dry the screen of your device using a soft cloth. Do not use any liquid cleaners.

Safety

Positioning the dock
Consider carefully where to attach the dock in your car. The dock should not block or interfere in any way with the following: Your view of the road Any of the controls in your car Any of your mirrors The airbag You should be able to reach your navigation device easily when it is in the dock without leaning or stretching. The diagrams show where you can safely attach the dock.

Show route summary

Tap this button to see your route.

View route

Driving View
When your TomTom XL starts, you are shown the Driving View along with detailed information about your current location. Tap the centre of the screen at any time to open the Main Menu. Note: The Driving View is shown in black and white until your XL locates your current position.
A Tap + and - to zoom in and out. B Quick menu - switch this on in the Preferences menu. C Your current position. D The name of the next major road or road sign information, if applicable. E Navigation instruction for the road ahead. Tap this area to repeat the last spoken instruction and to change the volume. F The name of the street you are on. G Information about your journey such as journey time, remaining distance and arrival time. To change the information shown, tap Status bar preferences in the Preferences menu. H GPS signal strength.

Advanced Lane Guidance

Your TomTom XL helps you prepare for motorway exits and junctions by showing you which lane you should be in. Note: This information is not available for all junctions or in all countries. For some exits and junctions, an image shows the turn and the lane you should take.
To turn the images off, tap Hide lane images in the Preferences menu. For other exits and junctions, your XL shows the lane you should take in the Status bar. To turn this guidance off, tap Change preferences in the Main Menu, then tap Status bar preferences. Clear the checkbox for Show lane guidance.
Finding alternative routes
Once you have planned a route, you may want to change something about the route, without changing your destination.

Why change the route?

Maybe for one of these reasons: You can see a roadblock or a line of traffic ahead. You want to travel via a particular location, to pick someone up, stop for lunch or fill up with petrol. You want to avoid a difficult junction or a road you dont like. Tap Find alternative. in the Main Menu to change the route that is currently planned.

Find alternative.

The Find alternative. button is also shown in the route summary screen after you plan a route. Tap this button to calculate an alternative to the route already planned. Your XL will look for another route from your current location to your destination. If you decide you would prefer to use the original route after all, tap Recalculate original. Why would I need to do this? Apart from the roads near your position and near your destination, the new route will use totally different roads to reach your destination. This is an easy way of calculating a totally different route. Tap this button if you can see a roadblock or a line of traffic ahead. You then have to choose how much of the route ahead you want to avoid.

Map corrections

There are two types of map correction: Corrections that are immediately shown on the map. These include, changing the traffic flow of a street, blocking or renaming a street and adding or editing POIs. This type of change is immediately shown on your own map. You can hide these corrections at any time in the Map Share preferences menu. Corrections that are reported to TomTom but not shown immediately on your map. These include, missing streets, errors in motorway entrances and exits and missing roundabouts. This type of correction is investigated by TomTom and once verified, is included in the next map release. These corrections are therefore not shared with the Map Share community.

Making a map correction

Important: For safety reasons, you should only mark a location when you are driving. Do not enter the full details of an error while you are driving. 1. Tap Map corrections in the Main Menu. 2. Tap Correct a map error.

Correct a map error

A list of possible map corrections is shown. 3. Select the type of correction you want to report. Note: If you tap Add missing POI or Report other error you will be asked for some additional information before the next step. 4. Select the method you want to use for selecting the location of the correction. 5. When you have found the location, tap Done. 6. Enter correction or confirmation of correction now.
Receiving the latest map updates
When you connect your TomTom XL to your computer, TomTom HOME automatically downloads any available map corrections and sends any changes you have made, to the Map Share community. There are several types of corrections which can be set in the Correction preferences menu.
Marking a map error while on the move
Important: For safety reasons, you should only mark a location when you are driving. Do not enter the full details of an error while you are driving. If you notice an item on your map that needs attention, you can mark the location using the Report button and then enter the details when you are no longer driving. To show the Report button in the Driving View or in the quick menu, do the following: 1. Tap Map corrections in the Main Menu. Tip: If you cannot see the Map corrections button in the Main Menu, tap Show ALL menu options in the Preferences menu. 2. Tap Correction preferences. 3. Tap Done and then tap Done again. 4. Select Show report button, then tap Done. The Report button is shown on the left-hand side of the Driving View. After you mark a location, you can add more information about the change when you open the Map corrections menu. For example, you are driving to a friend's house and you notice that the name of the street you are on is different from the one on your map. To report the

Edit POI

Delete the POI. Rename the POI. Change the telephone number of the POI. Change the category that a POI belongs to. Move the POI on the map. Tap this button to report other types of corrections. These corrections are not immediately applied to your map. Your TomTom XL sends a special report to TomTom Map Share. You can report missing streets, errors in motorway entrances and exits and missing roundabouts. If the correction you want to report is not covered by any of these report types, enter a general description then tap Other.

Report other error

Sounds and voices
Your TomTom XL plays the following kinds of sound: Spoken instructions Warnings
Changing the volume level
You can change the volume in three ways: Tap the bottom left hand area of the Driving View. The last spoken instruction is repeated and the volume level is shown. Move the volume slider to adjust the volume. In the Main Menu, tap Change preferences, then tap Volume preferences. Tap Test to check your changes.

Selecting a voice

To change the voice being used by your TomTom XL, tap Voice preferences in the Preferences menu, then tap Change voice. Select a voice from the list.

Voice preferences

Preferences
You can change the way your TomTom XL looks and behaves. Tap Change preferences in the Main Menu.
Hidden buttons and features
When you first start using your TomTom XL, all the buttons are shown in the menu. The buttons for the more advanced features can be hidden. This is a useful option because you are unlikely to use certain features very often. Tap this button in the Preferences menu, to reduce the number of buttons that are shown.

Show fewer menu options

You might want to do this so that only frequently used buttons are shown. When you need to use the buttons that are hidden, you can press Show ALL menu options in the Preferences menu to show all buttons. Tap this button in the Preferences menu, to show all the buttons available on your TomTom XL.

Manage Favourites

Tap this button to rename or delete Favourites. To find a Favourite quickly, tap Find, then start to type the name of the Favourite. As soon as the Favourite is shown in the list, you can select it.

Change Home location

Tap this button to set or change your Home location.
Do I need to use my actual home address for the Home location?
No. Your Home location can be a place you go often, for example, your office. It can be your actual home address, but it can be any address you like. Why should I set a Home location? Having a Home location means that you have a quick and easy way to navigate there, by tapping the Home button in the Navigate to. menu

Change voice

Tap this button to change the voice which gives you instructions.

Manage POIs

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. Tap this button to do the following: Set alerts for when you are near POIs.
For example, your XL can tell you when there is a petrol station nearby. Create your own POI categories and add POIs to them. For example, you could create a category of POIs called Friends, and add all your friends addresses as POIs in the category. You can even add your friends phone numbers with their address so you can call them from your XL. The following buttons are available: Add POI - tap this button to add a location to a POI category you have created. Warn when near POI - tap this button to be warned when you approach a POI. You can select the types of POI for which you wish to be warned. Delete POI - tap this button to delete a POI you created. Edit POI - tap this button to edit the details of a POI you created. Add POI category - tap this button to create a new POI category. Delete POI category - tap this button to delete a POI category you created.

Change car symbol

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. Tap this button to select a car symbol that will be used to show your current position in the Driving view.
Additional car symbols can be downloaded using TomTom HOME.
Change 2D/3D display / Turn on 2D display
Tap Turn on 2D display to change the perspective for viewing the map. For example, the 2D view shows a two dimensional view of the map as though viewed from above. To switch the view to a three dimensional perspective, tap Change 2D/3D display and select a view from the list.

Change 2D/3D display

Turn on 2D display
When should I use this? In some situations, it is easier to see the map from above. Perhaps if the road network is complicated or for times when you are walking while using your XL to navigate.

Show/Hide lane images

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. Tap this button to show or hide the arrows that warn you which lane you need to be in to navigate an approaching road exit or junction.

Show house number before street name Show street names - if you are using a computer voice for spoken instructions and have selected that street names should be read aloud, you do not need to select this option, since the street names will be read aloud even though this option is not selected. Show next street name Show current street name on map Show next motorway / signpost - if available, the road sign to follow or the name of the next major road on your route is shown at the top of the screen in the Driving View.

Planning preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. Tap this button to set the kind of route planned when you select a destination.
The following options are available: Ask me every time I plan Always plan fastest routes Always plan shortest routes Always avoid motorways Always plan walking routes Always plan bicycle routes Always plan for limited speed Tap the IQ Routes button to enable or disable IQ Routes. IQ Routes is used to plan the best possible route taking into account the real average speeds measured on the roads. Then set how your XL should handle the following when planning a route: Toll roads on the route Ferry crossings on the route HOV lanes on the route Unpaved roads
You can then set if the route summary screen closes automatically after you have planned a route. If you select No, you have to tap Done to close the route summary screen. Replanning preferences Select whether or not you want your TomTom XL to replan your route when a faster route is found while you drive. This might occur due to changes in the traffic situation.

Brightness preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. Tap this button to set the brightness of the screen. Move the sliders to set the brightness separately for day map colours and for night map colours. You can also set this option: Switch to night view when dark - your XL uses night colours for the Driving View based on the time of day. You can set the map colour scheme by tapping Change map colours.

Set owner

Itinerary Planning

What is an Itinerary?
An Itinerary is a plan for a journey including more locations than your final destination. An Itinerary can include the following items: Destination - a location on your journey where you want to stop. Waypoint - a location on your journey where you want to travel through without stopping.
Destinations are shown using this symbol.
Waypoints are shown using this symbol.
When would I use an Itinerary?
You could use an Itinerary for trips such as: A driving holiday through a country with lots of stops. A two day car journey with an overnight stop. A short drive which passes by Points of Interest. In all these examples you could tap Navigate to. for each place. However, if you use an Itinerary, you can save time by planning everything in advance.

Creating an Itinerary

1. Tap the screen to bring up the Main Menu. 2. Tap Itinerary planning.
The Itinerary planning screen opens. At first, there are no items on the Itinerary.

Itinerary planning

Note: This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu. 3. Tap Add and select a location. Tip: You can add items to your Itinerary in any order and rearrange the order later.

Following an Itinerary

When you use an Itinerary to navigate, the route will be calculated to the first destination on the Itinerary. Your TomTom XL calculates the remaining distance and time to the first destination and not for the whole Itinerary. As soon as you start to use an Itinerary, the route is calculated from your current position. You do not need to set a departure point. When you have passed a waypoint or reached a destination, it is marked as visited. Waypoints are shown on the map. Your XL will not warn you, when you are approaching a waypoint or when you arrive at a waypoint.

Organising an Itinerary

Tap an item on your Itinerary to open a page of buttons for editing the item. The buttons shown below are available. You can change a destination into a waypoint using this button. Remember that waypoints are points on your journey to your destination that you want to pass and destinations are places where you want to stop. This button is only shown if the item you tapped is a destination. You can change a waypoint into a destination using this button. Remember that destinations are places where you want to stop, and waypoints are points on your journey to your destination that you want to pass. This button is only shown if the item you tapped is a waypoint. Tap this button to miss out part of your Itinerary. Your XL will ignore this item and all the items before it in the Itinerary.

Tap this button to create a Favourite by entering latitude and longitude values.
Tap this button to select your last recorded position as your destination.
How can I use a Favourite?
You will normally use a Favourite as a way of navigating to a place without having to enter the address. To navigate to a Favourite, do the following: 1. Tap the screen to bring up the Main Menu. 2. Tap Navigate to. 3. Tap Favourite. 4. Select a Favourite from the list. Your XL calculates the route for you. 5. When the route is calculated, tap Done. Your XL will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen.
How can I change the name of a Favourite?
1. Tap the screen to bring up the Main Menu. 2. Tap Change preferences to open the Preferences menu. 3. Tap Manage Favourites. 4. Tap the Favourite you want to rename. 5. Tap Rename.
How can I delete a Favourite?
1. Tap the screen to bring up the Main Menu. 2. Tap Change preferences to open the Preferences menu. 3. Tap Manage Favourites. 4. Tap the Favourite you want to delete. 5. Tap Delete.

LIVE Services

Regional availability
Note: As well as using LIVE services in your own country, you may also be able to use LIVE services when travelling abroad. Not all LIVE services are available in all countries. For more information on available services, go to www.tomtom.com/services.

Safety Notice

Your TomTom navigation device contains a GSM/GPRS module which can interfere with electrical devices such as cardiac pacemakers, hearing aids and aviation equipment. Interference with these devices may endanger the health or life of others. Do not use near unprotected electrical units nor in areas where the use of mobile telephones is prohibited, such as hospitals and airplanes.
LIVE Services subscriptions
Checking your LIVE Services subscription You can check the status of your subscriptions at any time, by doing the following on your XL. In the Main Menu, tap TomTom Services and then tap My Services. Your XL also warns you when your LIVE Services subscription is approaching the renewal date. For more information about LIVE Services subscription and payment terms, go to tomtom.com/services. Renewing your LIVE Services subscription using your XL 1. In the Main Menu, tap TomTom Services and then tap My Services. The current status of your LIVE Services is shown. 2. Tap on the service you want to renew. Your XL confirms that you want to renew your subscription. 3. Tap Yes. The renewal request is sent to TomTom. You should complete payment online, on or before the date shown on your XL. Renewing your LIVE Services subscription using TomTom HOME 1. Connect your XL to your computer.

TomTom HOME starts and connects to your XL. 2. Open the LIVE Services section. 3. Check the status of your subscription and click on the service you want to renew. You are asked to provide your payment details. 4. Enter your payment details and complete the transaction. Your subscription is renewed.

TomTom HD Traffic

HD Traffic is a unique TomTom LIVE Service for receiving up-to-date traffic information. For more information about services and subscriptions, go to tomtom.com/services. In combination with IQ Routes, HD Traffic helps you plan the best possible route to your destination taking into account the latest traffic information. A route is calculated taking into account the current local traffic conditions. Your TomTom XL automatically receives regular traffic information updates. If traffic incidents are found on your route, you are asked if you want to replan the current route to try and avoid the traffic incidents.

Fuel Prices

The Fuel Prices service sends up-to-date information about fuel prices directly to your device or via TomTom HOME when your XL is connected to your computer.
Search for the best fuel prices
To search for the cheapest fuel prices, do the following. In this example, you will plan a route to the cheapest petrol station nearby. 1. Tap the screen to bring up the Main Menu, then tap TomTom Services. 2. Tap Fuel Prices. 3. Select the type of fuel used in your vehicle. 4. Tap Cheapest nearby, then tap the name at the top of the list. The location is shown on the map. 5. Tap Select. You are asked if you want to navigate to the petrol station. 6. Tap Yes. You may be asked if you need to arrive at a particular time, if this option is enabled. The route is planned and a summary of the route is shown on the map.
TomTom local search with Google
Using local search, you can search the Google listings to find shops and businesses near you, or any another location, and navigate there.

Using local search

To find a destination using local search and plan a route to that location, follow the steps below. In this example, you will search for a supermarket near to your current location. 1. Tap the screen to bring up the Main Menu, then tap Navigate to. 2. Tap the Google button. 3. Tap Search near you. 4. Type supermarket then tap OK. The locations that match your search are shown in a list. 5. Tap one of the locations in the list. The location is shown on the map. Tap Details to see more information about this location. 6. Tap Navigate there to plan a route to the location. Your TomTom XL plans a route to the location you selected.

Other services

The following services are also available on your TomTom XL: TomTom Weather TomTom Weather gives you five day weather reports for any location on your map. QuickGPSfixTM QuickGPSfix contains information about GPS satellite positions which helps your TomTom XL find your position faster.

My Services To check your subscription, tap TomTom Services in the Main Menu and then tap My Services. Note: When LIVE Services are unavailable, this image is shown in the Driving View. Your TomTom XL informs you when your LIVE Services subscription is due for renewal. You can use your XL to inform TomTom that you wish to renew your current subscription. For more information about LIVE Services subscription and payment terms, go to tomtom.com/services.

Using TomTom HD Traffic

The Traffic bar is shown on the right side of the Driving View. It warns you about traffic incidents on your planned route. The top of the Traffic bar represents your destination and shows the total delay time for any incidents on your route. The central section of the Traffic bar shows individual traffic incidents in the order they occur on your route. The bottom of the Traffic bar represents your current position and shows the distance to the next incident. To make the Traffic sidebar more readable some incidents may not be shown. These incidents will always be of minor importance and only cause short delays. Note: The colour of the sidebar changes colour depending on how old the traffic information is on your device. To find the quickest route to your destination taking into account the latest traffic information, do the following: 1. Tap the sidebar.
Tip: If you have trouble tapping the sidebar and the Main Menu is being displayed instead of the traffic menu, try tapping your finger half on the sidebar and half off the screen. 2. Tap Minimise traffic delays. Your device looks for the quickest route to your destination. It is possible that the new route may also include traffic delays, or may even be the same route as before. You can re-plan the route to avoid all delays, but this new route will take longer than the quickest route already shown. 3. Tap Done. Tip: You can let your TomTom device automatically minimise traffic delays for you.
You can set HD Traffic to minimise traffic delays on your route each time the latest traffic information updates are received. 1. Tap TomTom Traffic in the Main Menu. 2. Tap Change Traffic preferences. 3. Select Automatically minimise delays after every traffic update. 4. Tap Done.

Changing HD Traffic preferences
Use the Change Traffic preferences button to choose how HD Traffic works on your device. 1. Tap TomTom Traffic in the Main Menu. 2. Tap Change Traffic preferences.
Change Traffic preferences
3. To hear a beep sound when a new traffic incident occurs on your route, select Beep when traffic situation on route changes and then tap Done. 4. If a faster route is found while you are driving, Traffic can replan your journey to use the faster route. Select one of the following options and then tap Done. Always switch to that route Ask me if I want to change Never change my route 5. Tap Done.
Making commuting to work easier
The Home to work or Work to home buttons in the Traffic menu lets you check your route to and from work with one tap of a button. When you use either of these buttons, your device checks the route for possible delays and if it finds any, provides you with the possibility to avoid them.
The first time you use Home to work, you must set your traffic home and work locations, do the following: 1. Tap TomTom Traffic in the Main Menu. 2. Tap Show home-work traffic.

Change home-work

3. Tap Change home-work 4. Set your home location 5. Set your work location. You can now use the Home to work and Work to home buttons of the Show home-work traffic menu. Note: The home location you set here is not the same as the home location you can set in the Preferences Menu. In addition, the locations you use here do not have to be your actual home and work locations. If there is another route that you often travel, you can set Work/Home to use these locations instead.
For example, to check for delays on your route home, do the following: 1. Tap TomTom Traffic in the Main Menu. 2. Tap Show home-work traffic. 3. Tap Work to home. The driving view is shown. If the Traffic sidebar shows any delays on your route, tap the Traffic sidebar and then Minimise traffic delays to see your fastest route to home.
Checking traffic incidents in your area
Get an overview of the traffic situation in your area, using the map. To find local incidents and their details, do the following: 1. Tap TomTom Traffic in the Main Menu. 2. Tap Browse map.

Browse map

The map browser screen is shown. 3. Tap the blue compass image in the top right of the screen. The map centres itself on you current location and any traffic incidents in the area are shown.
4. Tap on any traffic incident to get more information. A screen is shown that gives you detailed information about the incident you chose. To display information about surrounding incidents use the left and right arrows at the bottom of this screen.
HD Traffic sidebar colours
The HD Traffic sidebar changes colours depending on how old the traffic information is on your device. The sidebar colours are: Dark blue - The traffic information on your device is up to date. Lilac - The traffic information on your device has not been updated for at least 10 minutes. HD Traffic still warns you about traffic incidents, but the information is at least ten minutes old. Grey - The traffic information on your device has not been updated for at least 15 minutes. HD Traffic will only warn you about traffic incidents once it has been able to update this information. Note: The traffic information on your device is updated automatically and the HD Traffic sidebar will normally remain dark blue. However, it is possible that device might not update traffic information, if for example there is no or poor network coverage in your area, or you are driving in a country other than the one for which you purchased TomTom HD Traffic.

Report button

To show the report button in the Driving View, do the following: 1. Tap TomTom Services in the Main Menu. 2. Tap TomTom Safety Cameras. 3. Tap Enable report button. The report button is shown on left-hand side of the Driving View or if you are already using the quick menu, its added to the buttons available in the quick menu.
Reporting a new safety camera while on the move
1. Tap the report button shown in the Driving View or in the quick menu to record the location the camera. 2. Tap Mobile camera or Fixed camera. 3. Tap the type of camera you want to report. Note: If the type of camera you choose has a speed restriction, you can also enter the speed.
Reporting a new safety camera while at home
You do not need to be at the location of a safety camera to report the new location.
To report a new safety camera location while you are at home, do the following: 1. Tap TomTom Services in the Main Menu. 2. Tap TomTom Safety Cameras. 3. Tap Report safety camera. 4. Tap Mobile camera or Fixed camera depending upon the type of safety camera. 5. Find the location of the camera you want to report using the Map browser,. Use the cursor to mark the exact location, then tap Done. 6. Tap on the type of camera you want to report and if necessary, the speed restriction for the camera.
Reporting incorrect camera alerts
You may receive an alert for a camera that is no longer there. To report an incorrect camera alert, do the following: 1. While you are at the location of the missing camera, tap Report in the Driving View. Note: This must be done within 20 seconds of receiving the camera alert. 2. Tap Remove. The next time you connect your device to TomTom HOME, the camera alert is reported as incorrect.
Types of safety camera you can report
When you report a safety camera, you can select the type of safety camera you are reporting. These are the different types of Safety camera: This type of safety camera checks the speed of passing vehicles.

Speed camera

This type of safety camera checks for vehicles breaking traffic rules at traffic lights.

Traffic light camera

This type of safety camera monitors traffic at toll road barriers.

Toll road camera

This type of safety camera checks the average speed vehicles between two fixed points.

Average speed check

This type of safety camera checks traffic on roads where access is restricted.

Vehicle restriction

All other types of camera that do not fall into any of the above categories.

Other camera

TomTom Safety Camera menu
To open the Safety Cameras menu, tap the TomTom Services in the Main Menu and then tap TomTom Safety Cameras. Tap this button to report a new safety camera location.

2009 TomTom International BV, Holanda. TomTom e o logotipo de "duas mos" esto entre as marcas comerciais, aplicativos ou marcas registradas possudas pela TomTom International B.V. Nossa garantia limitada e acordo de licenciamento do usurio final para o software includo se aplicam para este produto; ambos podem ser vistos em www.tomtom.com/legal
Data Source 2009 Tele Atlas N.V. Based upon: Topografische ondergrond Copyright dienst voor het kadaster en de openbare registers, Apeldoorn 2006. Ordnance Survey of Northern Ireland. IGN France. Swisstopo.
BEV, GZ 1368/2003. Geonext/DeAgostini. Norwegian Mapping Authority, Public Roads Administration / Mapsolutions. DAV, violation of these copyrights shall cause legal proceedings. This product includes mapping data licensed from Ordnance Survey with the permission of the Controller of Her Majestys Stationery Office. Crown copyright and/or database right 2009. All rights reserved. Licence number 100026920. Roskartographia
Some images are taken from NASAs Earth Observatory. The purpose of NASAs Earth Observatory is to provide a freely-accessible publication on the Internet where the public can obtain new satellite imagery and scientific information about our home planet. The focus is on Earths climate and environmental change: earthobservatory.nasa.gov/

2009 TomTom International BV, Holanda. TomTom e o logotipo de "duas mos" esto entre as marcas comerciais, aplicativos ou marcas registradas possudas pela TomTom International B.V. Nossa garantia limitada e acordo de licenciamento do usurio final para o software includo se aplicam para este produto; ambos podem ser vistos em www.tomtom.com/legal
Data Source 2009 Tele Atlas N.V. Based upon: Topografische ondergrond Copyright dienst voor het kadaster en de openbare registers, Apeldoorn 2006. Ordnance Survey of Northern Ireland. IGN France. Swisstopo.
BEV, GZ 1368/2003. Geonext/DeAgostini. Norwegian Mapping Authority, Public Roads Administration / Mapsolutions. DAV, violation of these copyrights shall cause legal proceedings. This product includes mapping data licensed from Ordnance Survey with the permission of the Controller of Her Majestys Stationery Office. Crown copyright and/or database right 2009. All rights reserved. Licence number 100026920. Roskartographia
Some images are taken from NASAs Earth Observatory. The purpose of NASAs Earth Observatory is to provide a freely-accessible publication on the Internet where the public can obtain new satellite imagery and scientific information about our home planet. The focus is on Earths climate and environmental change: earthobservatory.nasa.gov/