TD-9KX Setup Guide

Before using this unit, carefully read the sections entitled: USING THE UNIT SAFELY and IMPORTANT NOTES. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

C5100073

Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.

TD-9KX parts

Cable tie x 6 Connection cable (special for TD-9) Hi-hat control pedal (FD-8) Kick trigger pad (KD-8) Cymbal pad for hi-hat (CY-5) Cymbal pad for crash (CY-8) V-Cymbal for ride (CY-12R/C) V-Pad for snare (PD-105) V-Pad for tom (PD-85 x 3) Drum sound module (TD-9) AC adaptor Drum key
Drum key Stand (MDS-9) Hi-hat mount Cymbal mount x2 Owners Manual
Manual Set Setup Guide (this document) Quick Start Owners Manual

Assemble the stand

Assembly procedure
3. Adjust the pad mounts (C, four locations) as shown in the illustration. 4. Attach the cymbal mounts (D, two locations) and hi-hat mount (E) as shown in the illustration.

Attach the parts

* The parts required for mounting the cymbals and the hi-hat are included in the TD-9KX attachment box.
Attach the crash cymbal (CY-8) and ride cymbal (CY-12R/C)
Tighten the bolt with a drum key. Rotation stopper (note orientation) Attach the bolt so that it is at the right when seen by the performer. Tighten the wing nut to obtain an appropriate amount of sway. Wing nut Felt washer

Attach the hi-hat (CY-5)

Upper clutch Clutch felt (small)
1. Loosen the hand knobs (A, two locations) and spread open the left and right legs of the stand as shown in the illustration.
2. Loosen the hand knob of the snare pipe (B), and pull out the snare pipe toward the side of the performer.
Clutch felt (large) Lower clutch

CY-12R/C

Attach the snare (PD-105) and toms (PD-85)

Tighten

PD-85 CY-5 TD-9

Loosen Rod Loosen Rod

D : Cymbal mounts
C : Pad mounts E : Hi-hat mount

PD-105

Adjusting the tension

Tuning bolt Gap

Align with indentation

HEAD MADE BY REMO U.S.A.

Washer

While pressing

1. Finger-tighten all six of the tuning bolts in the sequence shown in the illustration. 2. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. Use drum key to tighten
A : Hand knobs B : Snare pipe
If the stand wobbles, loosen this hand knob and adjust the height.

135 135

3. Use the drum key to adjust the tension as needed.
Attach the sound module (TD-9)
Assemble the hi-hat control pedal (FD-8)
Attach the anchor bolt (if installing on a drum mat) Anchor bolt Anchor bolt Adjusting the pedal depth Loosen with the drum key, and tighten after adjusting Deeper Slide the arm Shallower

Assemble the kick (KD-8)

1.2 m (48)
* Do not spread open the stand farther than 135 degrees as shown in the illustration. Nor should you spread the stand wider than 1.2 meters (48 inches).
Spring for the anchor bolt

Remove the screws

Pull out the stand in the direction of the arrow, and use the screws you removed earlier to fasten the stand.
Connect the pads to the sound module
* To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration.
* Use cable ties to fasten the cables at the circled locations they do not interfere with your performance.

so that

RD RDB T2 T1 SNR T3

CR1 HH

Stereo headphones
Connect the AC adaptor and speakers
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

Connection procedure

Amplified speakers, etc.

1/4 plug (mono)

RD plug

BOW/EDGE output jack

1. Connect the cable to the TD-9 as shown in the illustration.
2. Labels indicating the pad to be connected are attached to the cable. Make connections as shown in the illustration.
3. Connect the AC adaptor, and fasten it to the cable hook as shown in the illustration to prevent it from being accidentally unplugged.

KIK HHC

AC adaptor Stereo 1/4" plug

(indicator)

RDB plug

BOW/BELL output jack

to AC outlet Power cable
This completes assembly and connections.
To learn about the TD-9s wide range of unique functionality, refer to Quick Start. If you need further information regarding the set up of TD-9KX, refer to the section If you dont hear any sound (p.18) in the Owners Manual.
Detailed explanation of each part

KD-8 (Kick)

01 Making the settings
* Use a commercially available kick pedal.

02 Attach the kick pedal

strikes the center of the head, then secure the kick pedal and KD-8 firmly in place.
03 Adjusting the foot plate height
* Depending on your kick pedal, it can be unstable when you attach it to the KD-8. Be sure to adjust the foot plate height so that the entire bottom surface of the pedal is attached to the floor.
This hight will vary depending on your kick pedal.
* Install the kick pedal securely. * Take care not to pinch your fingers. * The tips of the anchor bolts are sharp. Handle with care. * When moving the KD-8, be sure to remove the screws and fold the stand. Transporting the KD-8 while it remains open may subject the stand to excessive strain and result in damage to the stand.

Beater

1. 2. 3.
Remove the screws attached to the reverse side of the KD-8s trigger. Pull out the stand in the direction indicated by the arrow until it is fully extended. Using any commercially available drum key, tighten the screws removed in Step 1 so that the stand is firmly secured.
Commercially available kick pedal
Install the kick pedal securely.
* Adjust the height so that the entire pedal comes into contact with the floor.
Loosen the stands anchor bolts and remove the foot plate. Set the kick pedal so that the entire bottom surface is attached to the floor.
In most cases, the stand becomes somewhat elevated. Tighten the anchor bolts securely there to fix the stand and foot plate.
* Anti-skid tape is affixed to the foot plate. When transporting the KD-8, dont forget to pick up the foot plate.

04 Adjusting the anchor bolts
When using the kick pedal on a drum mat or similar surface, adjust the anchor bolts so their tips protrude from the plate. Then, secure the pedal in place; this will make it easier to use the kick pedal. However, when used on hard-surfaced flooring, the anchor bolts may damage the floor. Adjust the anchor bolts correctly.
05 When using a twin pedal
Position the two beaters equally apart from the center of the pad as shown in the figure at left. If one of the beater is further away from the center than the other, the sound from the further beater will be lower in volume, or will not sound as desired. Using a twin pedal will result in lower sensitivity as compared to when a single pedal is used. Raise the sensitivity on the sound module.

Output jack

Stand Anchor bolt
* The tips of the anchor bolts are sharp. Handle with care.

KD-8 component

Foot plate
When using on the drum mat
When using on hard-surfaced flooring

Other side

FD-8 (Hi-hat control pedal) CY-5 (Hi-hat) CY-8 (Crash cymbal)

CY-8 component names

CY-12R/C (Ride cymbal)

CY-12R/C component names

Bell BOW/EDGE output jack

FD-8 component names

Pad face Bow portion Edge portion

Pedal plate Anchor bolt

* When using on hard-surfaced flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. * To adjust the travel of the pedal, loosen the arm bolt.
Bow Edge Output jack Output jack
Fixing the cables (CY-12R/C)

Arm Control out jack

* Continuous playing may cause dis-coloration of the pad, but this will not affect the pads function.
Leave some slack in the cables Wind the cable tie twice Tighten it not to slip Turn back to fix the cables

PD-85 (Tom)

PD-105 (Snare)

PD-85 component names

PD-105 component names
* Be sure to adjust the head tension of the PD-85 / PD-105 before use.
Head replacement procedure
PD-85 replacement head (sold separately) PD-105 replacement head (sold separately) : MH-8 mesh head : MH-10 mesh head 1. Remove all tuning bolts and washers.

Sensor Hoop (Rim)

Head Wing nut

Hoop (Rim) Tuning bolts

* Striking the head when the head tension is loose may damage the sensor and head. * Do not apply excessive force to the sensor located below the center of the head of the PD-85 / PD-105. Doing so can interfere with accurate detection, and may damage it. * Due to the nature of the materials used in the sensor of the PD-85 / PD-105, changes in room temperature may affect the sensitivity of the sensor. * The rubber portion of the hoop is a consumable item that will undergo wear with use over time, depending on the number and strength of rim shots. Playing rim shots on the worn rubber portion may cause malfunctions. If this occurs, the hoop rubber should be replaced. Please contact Roland customer service regarding replacement of the hoop rubber.

Loosen

Drum key Hoops rubber portion Washer Tuning bolt
* While you remove the tuning bolts, press your finger against the lock bushing (see illustration below) so that it does not come out of the frame. * The lock bushing is a part that prevents vibration of the hoop from turning and loosening the tuning bolts when you play rim shots.
2. Hoop Lock bushing Frame 7. 3. 4. 5. 6.
Remove the hoop. Remove the old head. Place the new head on the frame. Place the hoop on the head. Pass the washers over the tuning bolts, and attach them to the hoop and frame. Adjust the head tension. For details, refer to the explanation on the opposite side of this leaflet.

Washer Wing bolt

Lugs Bracket Shell Output jack

Tuning bolt Output jack

Lock bushing If a lock bushing comes out of the frame while youre replacing the head, align the lock bushings slots with the + shaped portion of the frame, and press it firmly into the frame.

Holder Frame

USING THE UNIT SAFELY

IMPORTANT NOTES

For EU Countries

Placement

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. to damage or caused with and all its to domestic
The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit.
Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or otherwise harmfully affect the finish.

Maintenance

For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
Do not open or perform any internal modifications on the unit. (The only exception would be where this manual provides specific instructions which should be followed in order to put in place user-installable options.)
Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.

Additional Precautions

Use a reasonable amount of care when using the units buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information.
In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.
When connecting / disconnecting all cables, grasp the connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements.
To avoid disturbing your neighbors, try to keep the units volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).

Information

AFRICA
Al Fanny Trading Office 9, EBN Hagar Al Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: (022)-418-5531
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

PHILIPPINES

G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801

Do not drop the unit.

This instrument is designed to minimize the extraneous sounds produced when its played. However, since sound vibrations can be transmitted through floors and walls to a greater degree than expected, take care not to allow these sounds to become a nuisance to neighbors, especially when performing at night and when using headphones.

CURACAO

Zeelandia Music Center Inc. Orionweg 30 Curacao, Netherland Antilles TEL:(305)5926866

URUGUAY

Todo Musica S.A. Francisco Acuna de Figueroa 1771 C.P.: 11.800 Montevideo, URUGUAY TEL: (02) 924-2335

NORWAY

Roland Scandinavia Avd. Kontor Norge Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074

JORDAN

MUSIC HOUSE CO. LTD. FREDDY FOR MUSIC P. O. Box 922846 Amman 11192 JORDAN TEL: (06) 5692696

DOMINICAN REPUBLIC

Instrumentos Fernando Giraldez Calle Proyecto Central No.3 Ens.La Esperilla Santo Domingo, Dominican Republic TEL:(809) 683 0305

SINGAPORE

SWEE LEE MUSIC COMPANY PTE. LTD. 150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676

VENEZUELA

Instrumentos Musicales Allegro,C.A. Av.las industrias edf.Guitar import #7 zona Industrial de Turumo Caracas, Venezuela TEL: (212) 244-1122

POLAND

ROLAND POLSKA SP. Z O.O. UL. Gibraltarska 4. PL-Warszawa POLAND TEL: (022) 679 4419

KUWAIT

EASA HUSAIN AL-YOUSIFI & SONS CO. Al-Yousifi Service Center P.O.Box 126 (Safat) 13002 KUWAIT TEL: 802929
Never use or store the unit in places that are: Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are Damp (e.g., baths, washrooms, on wet floors); or are Humid; or are Exposed to rain; or are Dusty; or are Subject to high levels of vibration.
Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. The rubber portion of the striking surface is treated with a preservative to maintain its performance. With the passage of time, this preservative may appear on the surface as a white stain, or reveal how the pads were struck during product testing. This does not affect the performance or functionality of the product, and you may continue using it with confidence. Continuous playing may cause dis-coloration of the pad, but this will not affect the Pads function.

REUNION

Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429

TAIWAN

ROLAND TAIWAN ENTERPRISE CO., LTD. Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C. TEL: (02) 2561 3339

ECUADOR

Mas Musika Rumichaca 822 y Zaruma Guayaquil - Ecuador TEL:(593-4)2302364

PORTUGAL

Roland Iberia, S.L. Portugal Office Cais das Pedras, 8/9-1 Dto 4050-465, Porto, PORTUGAL TEL: 00 60

LEBANON

Chahine S.A.L. George Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 165857 Beirut, LEBANON TEL: (01) 20-1441
Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children.

SOUTH AFRICA

T.O.M.S. Sound & Music (Pty)Ltd. 2 ASTRON ROAD DENVER JOHANNESBURG ZA 2195, SOUTH AFRICA TEL: (011)Paul Bothner(PTY)Ltd. Royal Cape Park, Unit 24 Londonderry Road, Ottery 7800 Cape Town, SOUTH AFRICA TEL: (021) 799 4900

EUROPE

AUSTRIA
Roland Elektronische Musikinstrumente HmbH. Austrian Office Eduard-Bodem-Gasse 8, A-6020 Innsbruck, AUSTRIA TEL: (0512) 260

EL SALVADOR

OMNI MUSIC 75 Avenida Norte y Final Alameda Juan Pablo II, Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788

THAILAND

Theera Music Co. , Ltd. 100-108 Soi Verng Nakornkasem, New Road,Sumpantawongse, Bangkok 10100 THAILAND TEL: (02) 224-8821

ROMANIA

FBS LINES Piata Libertatii 1, 535500 Gheorgheni, ROMANIA TEL: (266) 364 609
TALENTZ CENTRE L.L.C. Malatan House No.1 Al Noor Street, Ruwi SULTANATE OF OMAN TEL: 2478 3443
Never climb on top of, nor place heavy objects on the unit.

GUATEMALA

Casa Instrumental Calzada Roosevelt 34-01,zona 11 Ciudad de Guatemala Guatemala TEL:(502) 599-2888
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

AUSTRALIA/ NEW ZEALAND

AUSTRALIA/ NEW ZEALAND Roland Corporation Australia Pty.,Ltd.
38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA For Australia Tel: (02) For New Zealand Tel: (09) 3098 715

BELGIUM/FRANCE/ HOLLAND/ LUXEMBOURG
Roland Central Europe N.V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811

RUSSIA

MuTek Dorozhnaya ul.3,korp.545 Moscow, RUSSIA TEL: (095) 981-4967
Al Emadi Co. (Badie Studio & Stores) P.O. Box 62, Doha, QATAR TEL: 4423-554
Roland Shanghai Electronics Co.,Ltd. 5F. No.1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800 Roland Shanghai Electronics Co.,Ltd. (BEIJING OFFICE) 10F. No.Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050

HONDURAS

Almacen Pajaro Azul S.A. de C.V. BO.Paz Barahona 3 Ave.11 Calle S.O San Pedro Sula, Honduras TEL: (504) 553-2029

SLOVAKIA

DAN Acoustic s.r.o. Povazsk 18. SK - Nov Zmky TEL: (035) 6424 330
This unit should be used only with a stand that is recommended by Roland.
Should you remove remove nuts, washers, screws, anchor bolts, etc., keep them in a safe place out of childrens reach, so there is no chance of them being swallowed accidentally.

For China

SAUDI ARABIA
aDawliah Universal Electronics APL Behind Pizza Inn Prince Turkey Street aDawliah Building, PO BOX 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 8643601

CROATIA

ART-CENTAR Degenova 3. HR - 10000 Zagreb TEL: (1) 466 8493
Roland Iberia, S.L. Paseo Garca Faria, 33-Barcelona SPAIN TEL: 91 00

MARTINIQUE

Musique & Son Z.I.Les Mangle 97232 Le Lamantin Martinique F.W.I. TEL: 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F.W.I. TEL: 715222

CZECH REP.

CZECH REPUBLIC DISTRIBUTOR s.r.o Voctrova 247/16 CZ - PRAHA 8, CZECH REP. TEL: (2) 830 20270

SWEDEN

Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-Nacka SWEDEN TEL: (0)00 20
Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. Bldg. No. 21, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384
When using the unit with a stand recommended by Roland, the stand must be carefully placed so it is level and sure to remain stable. If not using a stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling.

HONG KONG

Tom Lee Music Co., Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863

CENTRAL/LATIN AMERICA

ARGENTINA
Instrumentos Musicales S.A. Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700

DENMARK

Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200

SWITZERLAND

Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383

MEXICO

Casa Veerkamp, s.a. de c.v. Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699

TURKEY

ZUHAL DIS TICARET A.S. Galip Dede Cad. No.37 Beyoglu - Istanbul / TURKEY TEL: (0212) 10

FINLAND

Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)24 020

UKRAINE

EURHYTHMICS Ltd. P.O.Box: 37-a. Nedecey Str. 30 UA - 89600 Mukachevo, UKRAINE TEL: (03131) 414-40

BARBADOS

A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100

NICARAGUA

Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta.Avenida 1 Cuadra al Lago.#503 Managua, Nicaragua TEL: (505)277-2557

U.A.E.

Zak Electronics & Musical Instruments Co. L.L.C. Zabeel Road, Al Sherooq Bldg., No. 14, Ground Floor, Dubai, U.A.E. TEL: (04) 3360715
Rivera Digitec (India) Pvt. Ltd. 411, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

GERMANY

Roland Elektronische Musikinstrumente HmbH. Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090

BRAZIL

Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666

UNITED KINGDOM

Roland (U.K.) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701

PANAMA

SUPRO MUNDIAL, S.A. Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101

NORTH AMERICA

CANADA
Roland Canada Ltd. (Head Office) 5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) Roland Canada Ltd. (Toronto Office) 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707

GREECE/CYPRUS

STOLLAS S.A. Music Sound Light 155, New National Road Patras 26442, GREECE TEL: 2610 435400

INDONESIA

PT Citra IntiRama Jl. Cideng Timur No. 15J-15O Jakarta Pusat INDONESIA TEL: (021) 6324170
Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

PARAGUAY

Distribuidora De Instrumentos Musicales J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (595) 21 492147
Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855

HUNGARY

Roland East Europe Ltd. Warehouse Area DEPO Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011

MIDDLE EAST

BAHRAIN
Moon Stores No.1231&1249 Rumaytha Building Road 3931, Manama 339 BAHRAIN TEL: 942