Installation Instructions for: EMS P/N 30-6600
89-94 Nissan 240SX S13 KA24DE 91-94 Nissan Sentra B13 GA16DE 90-94 Nissan Pulsar GTi-R N14 SR20DET 91-93 Nissan NX B13 GA16DE 93-94 Nissan Altima U13 KA24DE 89-95 Nissan Bluebird U13 SR20DET 91-93 Infiniti G20 P10 SR20DE WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System allows for total flexibility in engine tuning. Misuse of this product can destroy your engine! If you are not well versed in engine dynamics and the tuning of management systems or are not PC literate, please do not attempt the installation. Refer the installation to a AEM trained tuning shop or call 800-423-0046 for technical assistance. You should also visit the AEM EMS Tech Forum at http://www.aempower.com NOTE: AEM holds no responsibility for any engine damage that results from the misuse of this product!
This product is legal in California for racing vehicles only and should never be used on public highways.
Note: Part number 30-6600 supersedes and replaces p/n 30-1600 and 30-1600U
Vehicle 1989-1994 Nissan 240SX S13 (KA24DE) 1991-1994 Nissan Sentra B13 (GA16DE) 1990-1994 Nissan Pulsar GTi-R N14 (SR20DET) 1991-1993 Nissan NX B13 (GA16DE) 1993-1994 Nissan Altima U13 (KA24DE) 1989-1995 Nissan Bluebird U13 (SR20DET) 1991-1993 Infiniti G20 P10 (SR20DE) Series I EMS 1600/U 1600/U 1600/U 1600/U 1600/U 1600/U 1600/U Series II EMS 6600
ADVANCED ENGINE MANAGEMENT INC. 2205 126th Street Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aempower.com Instruction Part Number: 10-6600
2010 Advanced Engine Management, Inc. Page 1 of 12
Thank you for purchasing an AEM Engine Management System. The AEM Engine Management System (EMS) is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM EMS differs from all others in several ways. The EMS is a stand alone system, which completely replaces the factory ECU and features unique Plug and Play Technology, which means that each system is configured especially for your make and model of car without any jumper harnesses. There is no need to modify your factory wiring harness and in most cases your car may be returned to stock in a matter of minutes. For stock and slightly modified vehicles, the supplied startup calibrations are configured to work with OEM sensors, providing a solid starting point for beginner tuning. For more heavily modified cars, the EMS can be reconfigured to utilize aftermarket sensors and has many spare inputs and outputs allowing the elimination of add-on rev-limiters, boost controllers, nitrous controllers, fuel computers, etc. It also includes a configurable onboard 1MB data logger that can record any 16 EMS parameters at up to 250 samples per second. Every EMS comes with all functions installed and activated; there is no need to purchase options or upgrades to unlock the full potential of your unit. The installation of the AEM EMS on the supported vehicles uses the stock sensors and actuators. After installing the AEMTuner software, the startup calibration will be saved to the following folder on your PC: C:\Program Files\AEM\AEMTuner\Calibrations\Nissan\ Multiple calibrations may be supplied for each EMS; additional details of the test vehicle used to generate each calibration can be found in the Calibration Notes section for that file. Please visit the AEM Performance Electronics Forum at http://www.aempower.com and register. We always post the most current strategy release, PC Software and startup calibrations online. On the forum, you can find and share many helpful hints/tips to make your EMS perform its best. TUNING NOTES AND WARNING: While the supplied startup calibration may be a good starting point and can save considerable time and money, it will not replace the need to tune the EMS for your specific application. AEM startup calibrations are not intended to be driven aggressively before tuning. We strongly recommend that every EMS be tuned by someone who is already familiar with the AEM software and has successfully tuned vehicles using an AEM EMS. Most people make mistakes as part of the learning process; be warned that using your vehicle as a learning platform can damage your engine, your vehicle, and your EMS.

Page 2 of 12

Read and understand these instructions BEFORE attempting to install this product. 1) Install AEMTuner software onto your PC The latest version of the AEMTuner software can be downloaded from the AEMTuner section of the AEM Performance Electronics forums. Series 2 units are not supported by the older AEMPro tuning software. 2) Change Cam/Crank Angle Sensor: AEM trigger disc MUST be used On Nissans, discrepancies have been observed in the OEM cam/crank angle signals between model years and/or trim levels. To avoid confusion the Series 2 EMS does not support the OEM Nissan trigger pattern. A replacement trigger disc is now included with every Nissan EMS and must be installed before attempting to start the engine. An AEM trigger disc is supplied with each 30-6600 EMS which fits KA, GA, and SR sensors. Please consult the following instructions supplement, which will be installed to the C:\Program Files\AEM\AEMTuner\Instructions folder: 10-6600-C for EMS - 30-66XX supplement- CAS trigger install KA, GA, and SR engines.PDF 3) Remove the Stock Engine Control Unit a) Access the stock Engine Control Unit (ECU). The location of the ECU on the Nissan 240SX vehicles is behind the kick-panel on the passenger side of the vehicle. All other Nissan/Infiniti control units are located on the floor behind the center console accessed from the passenger side. b) Carefully disconnect the wiring harness from the ECU. Avoid excessive stress or pulling on the wires, as this may damage the wiring harness. Some factory ECUs use a bolt to retain the factory connectors, and it must be removed before the harness can be disconnected. There may be more than one connector, and they must all be removed without damage to work properly with the AEM ECU. Do not cut any of the wires in the factory wiring harness to remove them. c) Remove the fasteners securing the ECU to the car body, and set them aside. Do not destroy or discard the factory ECU, as it can be reinstalled easily for street use and troubleshooting. 4) Install the AEM Engine Management System a) Plug the factory wiring harness into the AEM EMS and position it so the wires are not pulled tight or stressed in any manner. Secure the EMS with the provided Velcro fasteners. b) Plug the comms cable into the EMS and into your PC. c) Turn the ignition on, but do not attempt to start the engine. d) At the time these instructions were written, new EMS units do not require USB drivers to be installed to the PC. e) With the AEMTuner software open, select ECU>>Upload Calibration to upload the startup calibration file (.cal) that most closely matches the vehicles configuration to be tuned. Check the Notes section of the calibration for more info about the vehicle it was configured for. These files can be found in the following folder: C:\Program Files\AEM\AEMTuner\Calibrations\Nissan\ f) Set the throttle range: Select Wizards>>Set Throttle Range and follow the onscreen instructions. When finished, check that the Throttle channel never indicates less than 0.2% or greater than 99.0%, this is considered a sensor error and may cause some functions including idle feedback and acceleration fuel to operate incorrectly.

Page 3 of 12

5) Wiring accessories to the EMS: Please follow this suggested wiring diagram when adding accessories such as UEGO gauges, MAP sensors, IAT sensors, or switches for use with the EMS. Note that wire polarity is not important for the Air Temperature sensor.
AEM UEGO P/N: 30-5130 AEM EMS P/N: 30-41 O2 Sensor 1 Sensor Ground +5V Sensor Power MAP Signal Sensor Ground IAT Sensor Sensor Ground Switched Input Switch 6 Ground Air Temperature Sensor P/N: 30-2010 White (0-5V Analog + signal) Brown (Analog - signal)
Pink (Switched +12V Power) Red (+12V power, 5A fuse) Black (Battery or chassis ground)
Red (+5V Sensor Power) Green (MAP Signal) Black (Sensor Ground) MAP Sensor P/N: 30-2130-50
6) Ready to begin tuning the vehicle. a) Before starting the engine, verify that the fuel pump runs for a couple of seconds when the key is turned on and there is sufficient pressure at the fuel rail. If a MAP sensor is installed, check that the Engine Load indicates something near atmospheric pressure (approximately 101kPa or 0 PSI at sea level) with the key on and engine off. Press the throttle and verify that the Throttle channel responds but the Engine Load channel continues to measure atmospheric pressure correctly. b) Start the engine and make whatever adjustments may be needed to sustain a safe and reasonably smooth idle. Verify the ignition timing: Select Wizards>>Ignition Timing Sync from the pull-down menu. Click the Lock Ignition Timing checkbox and set the timing to a safe and convenient value (for instance, 10 degrees BTDC). Use a timing light and compare the physical timing numbers to the timing value you selected. Use the Sync Adjustment Increase/Decrease buttons to make the physical reading match the timing number you selected. Crankshaft timing marks are not labeled for some vehicles. Consult the factory service manual for more information. The diagram below shows marks for the 240SX:

Page 4 of 12

Note: This calibration needs to be properly tuned before driving the vehicle. It is intended for racing vehicles and may not operate smoothly at idle or part-throttle. NEVER TUNE THE VEHICLE WHILE DRIVING
7) Troubleshooting an engine that will not start a) Double-check all the basics first engines need air, fuel, compression, and a correctly-timed spark event. If any of these are lacking, we suggest checking simple things first. Depending on the symptoms, it may be best to inspect fuses, sufficient battery voltage, properly mated wiring connectors, spark using a timing light or by removing the spark plug, wiring continuity tests, measure ECU pinout voltages, replace recently-added or untested components with known-good spares. Check that all EMS sensor inputs measure realistic temperature and/or pressure values.

If the EMS is not firing the coils or injectors at all, open the Start tab and look for the Stat Syncd channel to turn ON when cranking. This indicates that the EMS has detected the expected cam and crank signals; if Stat Syncd does not turn on, monitor the Crank Tooth Period and T2PER channels which indicate the time between pulses on the Crank and T2 (Cam) signals. Both of these channels should respond when the engine is cranking, if either signal is not being detected or measuring an incorrect number of pulses per engine cycle the EMS will not fire the coils or injectors. With the engine not running, if the Engine Load changes when the throttle is pressed this usually indicates that there is a problem with the MAP sensor wiring or software calibration (when the EMS detects that the MAP Volts are above or below the min/max limits it will run in a failsafe mode using the TPS-to-Load table to generate an artificial Engine Load signal using the Throttle input). This may allow the engine to sputter or start but not continue running properly.

Page 5 of 12

Application Notes for EMS P/N 30-6600
KA24DE, GA16DE, SR20DE, SR20DET
Make: Model: Years Covered: Engine Displacement: Engine Configuration: Firing Order: N/A, S/C or T/C: Load Sensor Type: Number of Coils: Nissan/Infiniti 240SX, Sentra, Pulsar GTiR, NX, Altima, Bluebird, G20 1989-1995 1.6L, 2.0L, 2.4L Inline 4 1-3-4-2 N/A, T/C 0-5V MAF 1 (Distributor) Spare Injector Drivers: Spare Injector Drivers: Spare Injector Drivers: Spare Injector Drivers: Spare Coil Drivers: Spare Coil Drivers: Spare Coil Drivers: Boost Solenoid: EGT #1 Location: EGT #2 Location: EGT #3 Location: EGT #4 Location: Inj 5, Pin 23 Inj 6, Pin 105 Inj 7, Pin 14 Inj 8, Pin 114 Coil 2, Pin 7 Coil 3, Pin 5 Coil 4, Pin 25 PW2, Pin 111 Pin 8 Pin 15 Pin 44 Pin 115
Ignition driver type: Number of Injectors: Factory Injectors: Factory Inj Resistors: Injection Mode: Knock Sensors used: Lambda Sensors used: Idle Motor Type: Main Relay Control: Crank Pickup Type: Crank Teeth/Cycle: Cam Pickup Type: ** Cam Teeth/Cycle: Transmissions Offered: Trans Supported: Drive Options: Supplied Connectors: AEM extension/patch harness
0-5V Falling Edge trigger 4 (P&H drivers: Inj 1-4) 185cc - 444cc Pulsar GTiR only Sequential Duty-controlled solenoid Yes (not user programmable) Optical 24 (AEM trigger disc) Optical 1 (AEM trigger disc) Manual/Automatic Manual only FWD, RWD, AWD N/A 30-2995

Spare 0-5V Input: Spare 0-5V Input: Spare Low Side Driver: Spare Low Side Driver: Spare Low Side Driver: Spare Low Side Driver: Check Engine Light: Spare High Side Driver: Spare Switch Input*: A/C Switch Input*:
MAP, Pin 35 ADCR11, Pin 33 LS2, Pin 45 LS4, Pin 102 LS5, Pin 10 LS9, Pin 106 LS10 , Pin 24 HS1, Pin 28 Switch 2, Pin 43 Switch 6, Pin 41

Wire View of AEM EMS

WARNING: *All switch input pins must connect to ground; the switch should not provide 12V power to the EMS because that will not be detected as on or off.

Page 6 of 12

Engine Wiring Harnesses, swapped engine installations Many Nissan wiring harnesses have been found to contain significant differences between model years and/or trim levels. Likely differences include: Crank signal, Cam signal, Ignition switch wiring (the Ignition switch input controls the Main Relay output), injector and coil destinations. Official documentation for these vehicles was not offered in English, so it would be very wise to double-check the pinout destinations for these circuits. This is especially true if the vehicle contains a swapped engine or if the wiring harness has been cut, spliced, soldered, tapped or modified in any manner. It is the users responsibility to check that the wiring on the vehicle matches the pinout chart below. AEM will not be held responsible for loss or damage that can occur if the EMS is installed in a vehicle in which the wiring harness does not match the AEM-supplied pinout chart! The function of several pins have been changed from the original 30-1600 EMS, please see the pinout chart for more info. Primary Load Sensor, EMS Fuel Strategy The factory MAF (mass air flow) sensor(s) can be removed to help decrease intake air restriction; the EMS can be configured to use a MAP sensor to determine engine load. It is recommended to use a 3.5 bar MAP sensor or higher (P/N 30-2130-50). The factory Mass Air Flow sensor can be used as the primary load input for the AEM EMS if desired. Please check the Notes section of each calibration for more info about the vehicle setup and fuel strategy that calibration was configured to use. EMS Fuel Map, Boost Fuel Trim Table Some of the 30-6600 maps provided utilize the Boost Fuel Trim Table to provide a 1:1 fuel compensation above and below atmospheric pressure. In the startup calibration, the Boost Fuel Trim Table is configured to provide twice as much fuel when the manifold pressure is twice as high and half the fuel when the manifold pressure is half as high; this should help simplify the tuning process for different vacuum and boost levels. Notice the values in the main Fuel Map do not change above 100 kPa (0 psi boost), the fuel correction is being made by the Boost Fuel Trim Table. Note: the Boost Fuel Trim Table must be adjusted if a different MAP sensor is installed or if the Load breakpoints are adjusted. The Boost Fuel Trim value should be set to -90 at 10kPa, 0 at 100 kPa, +100 at 200 kPa, +200 at 300 kPa, etc Peak and Hold Injector Drivers Injectors 1-4 include Peak (4 amps) and Hold (1 amp) injector drivers. These drivers may be used with peak and hold or saturated type injectors. Some factory wiring harnesses may contain a resistor pack to prevent excessive current when using low-impedance injectors with the stock ECU. With the 30-6600 installed, users can elect to remove and bypass the OEM resistor pack (if one was installed) for more precise control of lowimpedance injectors. Please note that the injector response time will be different with and without the factory injector resistor pack. If the OEM resistor pack has been removed and bypassed, please use the correct battery offset wizard for your injectors. Most battery offset wizards will specify <P&H DRIVER> if they are intended for use without a resistor pack.

Page 7 of 12

Connection Diagram for EMS P/N 30-6600
PnP Available Dedicated Means the Plug and Play system comes with this configured for proper operation of this device. Is still available for reassignment by the end user. Means the function is not currently allocated and is available for use Means the location is fixed and cant be changed
1989-1994 Nissan 240SX S14 KA24DE 1991-1994 Nissan Sentra B13 GA16DE 1990-1994 Nissan Pulsar GTi-R N14 SR20DET 1991-1993 Nissan NX B13 GA16DE 1993-1994 Nissan Altima U13 KA24DE 1989-1995 Nissan Bluebird U13 SR20DET 1991-1993 Infiniti G20 P10 SR20DE

AEM EMS 30-6600

Ignition Signal Tachometer Signal Ignition Check ECCS Relay control, Ignition Relay control --ECCS Ground Data Link Connector EGR Sensor (Except 89-90 Non CA 240SX and SR20DET) Cooling Fan Relay Cooling Fan High Speed (A/T 2.0L only) Air Conditioner Relay Swirl Control Valve (89-90 240SX Only)/VTC Solenoid (1.6L only) ECCS Ground Diagnostics Clock
Coil 1 Low Side 7 --Main Relay Coil 3 Power Ground Coil 2 EGT 1 Low Side 3 + Low Side 12 Low Side 5 Low Side 6 CAN1H Power Ground Injector 7
Output Output --Output Output Input Output Input Output Output Output Input Input Output
PnP for Coil 1, 0-5V falling edge trigger PnP for Tachometer Not Used Dedicated, EMS activates relay with switched GND Available Coil 3, 0-5V falling edge trigger Dedicated Available Coil 2, 0-5V falling edge trigger Available, jumper set for 0-5V Input PnP for Cooling Fan, can be activated by LS3 or LS12 output Available, Switched Ground, 1.5A max Available, Switched Ground, 1.5A max Dedicated. CAN high side Dedicated Available, Switched Ground, 1.5A Max

Page 8 of 12

AEM EMS 306600
Data Link Connector Mass Air Flow Sensor Mass Air Flow Ground Engine Coolant Temperature Sensor Oxygen Sensor Throttle Position Sensor Sensor Ground Crankshaft Reference Signal Diagnostics check (SR20 only) Malfunction Indicator Light Swirl Control Valve (91-94 240SX only) Air Temp Sensor (Late 89 and all 90 240SX) Knock Sensor (Except 89-90 240SX & 1.6L) Throttle Signal Output (A/T only) Sensor Ground Crankshaft Reference Signal
EGT 2 MAF Power Ground Coolant O2 #1 TPS Sensor Ground Cam (T2) Injector 5 Low Side 10 Coil 4 AIT Knock 1 High Side 1 Sensor Ground Cam (T2)

Input Input Input Input Input Input Output Input Output Output Output Input Input Output Output Input
Available, jumper set for 0-5V input PnP for MAF Sensor Dedicated PnP for Coolant Temp Sensor Dedicated, 0-5V input signal PnP for Throttle Position Sensor Dedicated Dedicated, must use AEM replacement trigger disc. Connects to pin 30 Available, Switched Ground, 1.5A Max Available, Switched Ground, 1.5A Max Available Coil 4, 0-5V falling edge trigger Available, AIT Sensor Input PnP for Knock Sensor Available, +12V, 1.5A Max Dedicated Dedicated, must use AEM replacement trigger disc. Connects to pin 22

Page 9 of 12

115 116
Crankshaft Position Sensor Signal Vehicle Speed Idle Sw (89-90 240SX)/5 Pos Sw (91-94 240SX) Start Signal Neutral Position Switch Ignition Switch Throttle Position Sensor Power Power Supply for ECM ECCS Ground Crankshaft Position Signal Air Conditioner Switch 4th Position Switch (91-94 240SX only) Power Steering Oil Pressure Switch Idle Switch Positive Side (89-90 240SX); Rear window defogger (91-94 240SX) Air Conditioner FICD (Except 2.0L); Position Sw (89-90 240SX) Back-up Power Supply Power Supply for ECM ECCS Ground Injector 1 Pulse Secondary Air Inj (240SX & 91-93 2.0L only) Injector 3 Fuel Pump Relay control EGR Control Solenoid Valve Pressure Regulator Control Sol (89-90 240SX only) ECCS Ground ECCS Ground Back-Up Power Supply Injector 2 O2 Sensor Heater (91-94 2.0L & 94 1.6L only) Injector 4 Idle Auxiliary Air Control Valve ----ECCS Ground
Crank Signal Vehicle Speed ADCR11 +12V Switched MAP Ignition Switch +5V Sensor +12V Switched Power Ground Crank Signal Switch 6 CAN1L Switch 2 EGT 3 Low Side 2 Permanent +12V +12V Switched Power Ground Injector 1 Low Side 4 Injector 3 Low Side 11 Injector 6 Low Side 9 Power Ground Power Ground Permanent +12V Injector 2 PW 2 Injector 4 PW 1 Injector 8 EGT 4 Power Ground
Input Input Input Input Input Input Output Input Input Input Input Input Input Input Output Input Input Input Output Output Output Output Output Output Input Input Input Output Output Output Output Output Input Input
Dedicated, must use AEM replacement trigger disc. Connects to pin 40 PnP for Vehicle Speed Sensor Available, 0-5 Volt Input Dedicated Available, Manifold Pressure Dedicated, +12V activates Main Relay circuit Dedicated Dedicated, +12V power when ECCS Relay is on Dedicated Dedicated, must use AEM replacement trigger disc. Connects to pin 31 PnP for A/C Switch Dedicated, CAN low side Available, Switched Input Available, jumper set for 0-5V Input Available, Switched Ground, 1.5A Max Dedicated, used to store internal log Dedicated, +12V power when ECCS Relay is on Dedicated PnP for Injector 1 (Peak & Hold 4A/1A driver) Available, Switched Ground, 1.5A max PnP for Injector 3 (Peak & Hold 4A/1A driver) PnP for Fuel Pump Available, Switched Ground, 1.5A max PnP for Fuel Pump Dedicated Dedicated Dedicated, used to store internal log PnP for Injector 2 (Peak & Hold 4A/1A driver) Available, Switched Ground, 1.5 max PnP for Injector 4 (Peak & Hold 4A/1A driver) PnP for Idle Air Control Available, Switched Ground, 1.5A max Available, jumper set for 0-5V Input Dedicated

Page 10 of 12

30-1600 (Series 1) vs 30-6600 (Series 2) EMS differences: The EMS functions assigned to certain pins have been changed and no longer match the 30-1600 EMS. Unless otherwise noted, the following pins and functions will need to be manually reconfigured after using AEMTuner to convert a V1.19 301600, Series 1 EMS calibration for use with the 30-6600 Series 2 hardware.
Pin Vehicle harness destination CAN TX Data CAN --30-1600 function Low Side 8 Injector 8 Switch 1 EGT 2 30-6600 function CAN1H EGT 2 CAN1L Injector 8 Notes LS8 not available Injector 8 moved to pin 114 Switch 1 not available EGT 2 moved to pin 15

Page 11 of 12

AEM Electronics Warranty
Advanced Engine Management Inc. warrants to the consumer that all AEM Electronics products will be free from defects in material and workmanship for a period of twelve months from date of the original purchase. Products that fail within this 12-month warranty period will be repaired or replaced when determined by AEM that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be responsible for special, incidental or consequential damages or cost incurred due to the failure of this product. Warranty claims to AEM must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12-month warranty period. Improper use or installation, accident, abuse, unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Merchandise Authorization (RMA) number. Product must be received by AEM within 30 days of the date the RMA is issued. Please note that before AEM can issue an RMA for any electronic product, it is first necessary for the installer or end user to contact the tech line at 1-800-423-0046 to discuss the problem. Most issues can be resolved over the phone. Under no circumstances should a system be returned or a RMA requested before the above process transpires. AEM will not be responsible for electronic products that are installed incorrectly, installed in a non approved application, misused, or tampered with. Any AEM electronics product can be returned for repair if it is out of the warranty period. There is a minimum charge of $75.00 for inspection and diagnosis of AEM electronic parts. Parts used in the repair of AEM electronic components will be extra. AEM will provide an estimate of repairs and receive written or electronic authorization before repairs are made to the product.

Page 12 of 12

MAZDA MX6, 626 2.0L 4cyl 95-97
56027N D MAZDA MX6/ FORD PROBE 2.5L 6 T0T57271 MZ27
MAZDA MX6/ FORD PROBE 95-02
56030N D MAZDA MPV 3.0L 96-98 (NEW) T0T57571 MZ-30

MAZDA MPV 3.0L 96-98

56099 D MAZDA 626 2.0L 4CY 2P 92T4T72574

MAZDA 626 2.0L 92-

56120N D New Mit. EXPO LRV 1993-94 T6T58071
DODGE COLT & MITSUBISHI EXPO 93-94
56121 D DODGE COLT/VISTA 1.8L 2*6 T6T57671
DODGE COLT/VISTA 1.8L 92-94
56121N D DODGE COLT/VISTA 1.8L 2*6 (NE T6T57671
56122 D DODGE COLT 1.5L T6T57171 DG22
DODGE COLT 1.5L 91-94, mirage 1.5 91-94
56122N D NEW DODGE COLT 1.5L T6T57171 DG22
56123 D DODGE AVENGER 2.5L 95-00 T5T57171

DODGE AVENGER 95-00

56200N D NEW VW FITS ALL YEAR 356 & 91 0-231-178-009
VOLKSWAGEN BEETLE TUNE-UP KITS
56201N D NEW VW FITS ALL YEAR 356 & 91 9-230-081-094
56202N D BOSCH (SVDA) VACUUM ADVANC 0-231-170-034
VOLKSWAGEN T.1 1.2L-1.6L 72-75
56900 D FORD TELSTAR 88A4T-4F67971

FORD TELSTAR 88-