* Due to improvements, specifications and appearance are subject to change without notice.

Handling Precautions

Do not disassemble or alter the product. Doing so may result in damage or deterioration to the product. Do not step on or place heavy objects on the product. It may result in damage. Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation, discoloration, damage or deterioration. When connecting or disconnecting the cable, make sure that you hold the plug, not the cable. Also, never place any heavy objects on the cable and never allow any sharp objects to come into contact with the cable. Applying excessive force to the cable may result in damage to the cable such as cutting the wires, etc. To clean the product, please wipe with a soft cloth or a damp cloth that been wrung out thoroughly, If the product is soiled, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration.
A white powdery substance may be present on the backside of the pads rubber. This powder is a remnant of one of the ingredients found in the rubber and will not cause have any negative impact on the function or performance of the pad. We apologize for the inconvenience but if the powder is present, please follow the instructions above and clean the pad to remove the powder.

Exemple de configuration

CRASH (PCY65) DTXPLORER RIDE (PCY65)

Setup-Beispiel

Set up example

TOM 1 (TP65)

TOM 2 (TP65)
CHARLESTON (HI HAT) (TP65)
HI-HAT (TP65) GROSSE CAISSE (KICK) (KP65) KICK (KP65) TOM 3 (TP65) TOM 3 (TP65)
CAISSE CLAIRE (SNARE) (TP65) HI HAT (TP65) COMMANDE DE CHARLESTON (HH CONTROL) (HH65)

SNARE (TP65)

KICK (KP65)

HI-HAT-CONTROL (HH65)

SNARE (TP65) HI HAT CONTROL (HH65)
TOM 3 (TP65) PDALE DE GROSSE CAISSE (FP6110) Support de tom FUSSMASCHINE (FP6110)

TP65 (Pad de ft)

Ce type de pad est utilis pour la caisse claire, les toms (x 3) et la cymbale charleston de lensemble. Faites glisser le pad sur le support de ft (tige hexagonale) fix au rack RS40 et serrez bien le boulon de la bride de fixation.

Tom Holder

TP65 (Tom-Pad)
Dieser Pad-Typ wird fr die Snaredrum, die Tomtoms (x3) und das Hi-Hat des Systems verwendet. Stecken Sie das Pad auf den Tom-Halter (Sechskantrohr) am Rack-System (RS40) und ziehen Sie die Spannschraube fest an.

Tom-Halter

Introduire Boulon de fixation

Aufstecken Spannschraube

TP65 (Tom Pad)
This pad is used for the system's snare drum, tom toms (x3) and hi-hat. Slide the pad onto the tom holder (hexagonal bar) attached to the rack system (RS40) and firmly tighten the clamp bolt to secure.

FOOT PEDAL (FP6110)

Clamp Bolt

Insert

PCY65 (Pad de cymbale)
Ce type de pad est utilis pour les cymbales ride et crash de lensemble. Placez le pad entre les deux tampons de feutre, puis fixez-le au support de cymbale du rack RS40.

crou oreilles Feutre

PCY65 (Cymbal-Pad)
Dieser Pad-Typ wird fr die Becken (Crash- und Ride-Cymbal) des Systems verwendet. Befestigen Sie die Pads mit jeweils einem Filz darunter und darber am Rack-System (RS40).

Flgelmutter Filz

Wing Nut Felt

PCY65 (Cymbal Pad)
This pad is used for the system's crash and ride cymbals. Place the pad between the two felts and then secure onto the rack system's (RS40) cymbal holder.
Feutre Support de cymbale

Filz Cymbal-Halter

HH65 (Pdale de charleston)

Felt Cymbal Holder

HH65 (Hi-Hat-Control-Pedal)

HH65 (Hi-Hat Control Pedal)
This pedal is used to control the opening and closing of the hi-hat cymbal. Position the pedal underneath the rack mounted hi-hat cymbal pad (TP65) in a manner that provides both player comfort and pedal stability.

Cette pdale sert commander louverture et la fermeture de la cymbale charleston. Placez la pdale laplomb du pad de cymbale charleston (TP65) de faon ce que le jeu puisse tre confortable et la pdale stable.

Mit diesem Pedal steuern Sie das ffnen und Schlieen des Hi-Hat-Cymbals (Charlestonmaschine). Stellen Sie das Pedal unter dem am Rack angebrachten Hi-Hat-Pad (TP65) so auf, dass es bequem bettigt werden kann und sicher steht.

Rondelle Rondelle ressort Boulon oreilles Base Ergot Velcro Battant Corps du pad

KP65 (Kick Pad)

This pad is used as the system's bass drum. 1. Assemble the KP65. As shown in the illustration, remove the base attachment wing bolts, washers and spring washers (4 each) that are attached to the main body, and use those to attach the base to the main body. Only loosely tighten the wing bolts in this step. 2. Attach the foot pedal (FP6110, shown below) to the KP65. When attaching the pedal, make sure that the pedal's hoop clamp firmly clamps onto the ridge that runs across the front of the KP65's base. Rotate the T-handled bolt to the left to loosen the hoop clamp and to the right to tighten. 3. Adjust the base's position so that the DP65 pad's playing surface is vertical when the foot pedal is attached, and make sure that the KP65 is stable when the beater hits the pad. After the position is determined, firmly tighten the wing bolts to secure. 4. Adjust the pedal's position and the shaft length of the beater so that the foot pedal's beater hits in the center of the kick pad.
Washer Spring Washer Wing Bolt Base Spur Velcro Beater Main Body

Haupteinheit

Schlegel

Schelle

T-Schraube
Bride cerclage Boulon manette de serrage en T
Hoop Clamp T-Handlet Bolt
1 SNARE 2 TOM TOM TOM RIDE 6 CRASH HI HAT 8 KICK HH CONTROL
SNARE TOM 1 TOM 2 TOM 3 RIDE CRASH HI HAT KICK HH CONTROL
Lsen Sie die Schlegelwinkel-Einstellschraube mit einem Stimmschlssel (nicht im Lieferumfang), um den Schlegelwinkel wunschgem einzustellen, und ziehen Sie die Schraube dann wieder fest an. Die Rckholkraft des Pedals ist einstellbar. Zum Erhhen der Kraft lsen Sie Mutter A und ziehen dann Mutter B an (siehe Abbildung). Zum Vermindern der Kraft lsen Sie Mutter B (siehe Abbildung). Sobald die gewnschte Rckholkraft vorliegt, ziehen Sie Muttern A und B fest an.

Einstellen der Federspannung
Le ressort qui assure le retour en position haute de la pdale est rglable. Pour augmenter la tension du ressort, desserrez lcrou A puis serrez lcrou B illustrs sur la figure. Pour rduire la tension du ressort, desserrez lcrou B illustr sur la figure. Une fois obtenue une tension satisfaisante du ressort, resserrez bien les crous A et B.

Dpannage

Si vous rencontrez des problmes dans votre utilisation des pads livrs avec lensemble, par exemple sils ne semblent pas produire de son, etc., veuillez lire attentivement le mode demploi du DTXPLORER, vrifier tous les branchements du systme et effectuer tous les rglages indiqus avant de contacter le service aprs vente pour une rparation. Si, en procdant ainsi, vous narrivez pas faire disparatre le problme et si celui-ci persiste, contactez le revendeur chez qui vous avez achet le produit.

Problembeseitigung

Sollten hinsichtlich der mit dem Set gelieferten Pads beim Gebrauch Probleme (kein Ton usw.) auftreten, lesen Sie bitte in der Bedienungsanleitung des DTXPLORER nach und prfen die Anschlsse und Einstellungen, bevor Sie das System in Reparatur geben. Sollte sich ein Problem nicht beseitigen lassen, wenden Sie sich bitte an den Hndler, bei dem das Produkt erworben wurde.
Einstellen des Schlegelwinkels
Rglage de la tension du ressort
The recoil tension of the foot board is adjustable. To increase spring tension, loosen nut A then tighten nut B shown in the illustration. To decrease spring tension, loosen nut B shown in the illustration. Once the desired spring tension has been obtained,firmly tighten nuts A and B.

Connections

Use the supplied 9ch snake cable to connect the pad's OUTPUTs to the pad inputs on the DTXPLORER Drum Trigger Module. Connect the cable's L-shaped plugs to the pads.
If the pads are positioned as shown in the illustration in the "Setup" section, follow the labels on 9ch snake cable's plugs (SNARE, TOM1 , etc.) and connect the cable's plugs to their corresponding pads. If a setup other than the one shown above is used, connect the plugs to the pads according to the cable's length.
1 SNARE 2 TOM TOM TOM RIDE 6 CRASH HI HAT 8 KICK HH CONTROL SNARE TOM 1 TOM 2 TOM 3 RIDE CRASH HI HAT KICK HH CONTROL
SNARE HH CONTROL HI HAT CONTROL SNARE (TP65) (HH65)

TOM 3 TOM 3 (TP65)

Adjusting the Output Level (LEVEL): PCY65/KP65

The PCY65 and KP65 are equipped with level adjustment knobs for adjusting the trigger output level. The pad's output level should be adjusted in regard to how hard you hit the pad when playing and the dynamic level which you require. Rotate the level adjustment knob to the right (+) to increase the output level, and to the left to decrease output level.
NOTE: Adjust the level so that the DTXPLORER'S input level display registers 90-95% when you play ff (fortissimo : the loudest playing level). Please refer to the Owner's Manual that came with the DTXPLORER for more information. Too high of an output level setting will result in a narrow dynamic range (the difference between loud and soft) or may produce trouble such as double triggers (a single hit produces multiple sounds), etc. : Do not put excessive pressure on the level adjustment knob, it may result in damage.

LEVEL Adjustment Knob

Connecting an External Pad: KP65
The KP65's external pad input jack can be used to connect an additional pad to the system. In this case, the external pad's trigger signal is sent to the DTXPLORER's Input 9 (the KP65 is connected to Input 8).
TP65 PCY65 NOTE: Any of the pads in the DTX series can be used as an external pad however, pads equipped with rim switches (TP65S, PCY65S, etc.) will not be able to produce sounds from their rims. Functions that utilize the rim switch (choke, mute) are also not available.
9-Channel Snake Cable (KICK)
DTXPLORER (INPUT 8 KICK/9)

Specifications

Dimensions 312(W) X 245(D) X 46.5(H) mm Weight 620g Sensor System Trigger Sensor (Piezo) x 1 Output Jack. Standard Monaural Phone Jack
Dimensions. 233(W) x 271(D) x 416(H) mm (When Assembled) Weigh.. 2.7kg Sensor System.. Trigger Sensor (Piezo) x 1 Input Jack. Standard Monaural Phone Jack Output Jack. Standard Stereo Phone Jack
Dimensions Weight Sensor System Output Jack 142mm (W) X 398mm (D) X 104mm (H) 1.5Kg Continuous Switch x1 Standard Stereo Phone Jack
Dimensions. 138(W) x 329(D) x 210(H) mm (when assembled: excludes beater) Weight.. 1.2kg (includes beater) Drive System. Belt Beater.. Felt * Improvements may result in a change in the specifications and/or design of the product without notice.

Dimensions. 220(diameter) X 61(H) (excluding the clamp bolt) Weight.. 980g (including the clamp bolt) Sensor System.. Trigger Sensor (piezo-electric) x1 Output Jack. Standard Monaural Phone Jack

Replacing Worn Out Parts

After extended use, some of the product's parts will wear out or their quality will deteriorate (pad rubber, cushion material used inside the pads, switches, jacks, etc.). The life of these parts will vary depending upon the circumstances under which the product is used. Please contact the dealer from whom you purchased the product about replacing worn parts.

Troubleshooting

If you experience any problems when using the pads that came with the set, such as sound not being produced, etc., please carefully read the Owner's Manual that came with the DTXPLORER, and check the connections and settings before requesting repair. If a solution to the problem cannot be found and the problem persists, please contact the dealer from whom you purchased the product.

WG12370

Utilisez une clef de rglage de batterie (non fournie) pour desserrer le boulon de rglage de langle du battant, rglez langle voulu, puis resserrez.
Rglage de langle du battant
Use a drum key (not supplied) to loosen the beater angle adjustment bolt and adjust the angle of the beater, then secure.
Adjusting the Spring Tension

Schlegel (DoppelFumaschine)

Battant

Battants (Pdale double)

Beater

Beater (Double Foot Pedal)
HINWEIS: Das KP65 kann mit einer Doppel-Fumaschine (Yamaha DFP7210 usw., separat erhltlich) konfiguriert werden. Richten Sie die Doppel-Fumaschine so ein, dass der Zwischenraum zwischen den beiden Schlegelkpfen genau im Zentrum der Schlagflche liegt. HINWEIS: Wenn das Produkt auf einem speziellen Drum-Riser aufgestellt wird oder Schden an der Bodenflche ohne Belang sind, fahren Sie die Stachel der Fumaschine aus, so dass deren Spitzen fest in den Boden greifen und ein Verrutschen des KP65 beim Spielen verhindern.
REMARQUE : Le pad KP65 peut tre mont avec une pdale double battant (Yamaha DFP7210, etc., vendue sparment). Lorsque vous utilisez une pdale double battant, rglez sa position et les longueurs des battants de telle sorte que lespace entre les deux ttes des battants se situe au centre du pad. REMARQUE : Si le produit est install sur un podium spcial pour batterie, ou si les atteintes au plancher ne posent pas de problme, sortez les ergots de la pdale de sorte que leurs pointes agrippent le podium ou le sol, afin dempcher lensemble de bouger pendant le jeu.
NOTE: The KP65 can be configured with a double foot pedal (Yamaha DFP7210, etc., sold separately). When using a double foot pedal configuration, adjust the pedal's position and the length of the beaters so that the space between the two beaters is positioned in the center of the head. NOTE: If the product is set up on a special purpose drum riser, or if damage to the floor is not a concern, extend the foot pedal's spurs so that their points grip the riser or floor to prevent the KP65 from moving during performance.

FP6110 (Fumaschine)

FP6110 (Pdale de grosse caisse)
La pdale de grosse caisse FP6110 se fixe au pad de grosse caisse KP65. Assemblez dabord la pdale comme illustr sur la figure. 1. Introduisez la tige de stabilisation de la pdale dans les orifices du cadre comme illustr. 2. Fixez le battant comme illustr, et servez-vous du boulon de fixation pour fixer le battant dans la position adquate. Si ncessaire, effectuez les rglages ci-aprs.

FP6110 (Foot Pedal)

Tte du battant Boulon de rglage de langle du battant Boulon de verrouillage du battant Courroie Rouleau ressorts Cadre crou A Pdale crou B Tige de stabilisation de la pdale
Schlegelkopf SchlegelwinkelEinstellschraube Federrolle Rahmen Mutter A Mutter B
HH CONTROL SNARE HI HAT CONTROL SNARE (TP65) (HH65)
Die Fumaschine FP6110 wird mit dem KP65 verschraubt. Schlegel1. Bauen Sie die Fumaschine zunchst wie in der Arretierschraube Abbildung zusammen. Riemen Stecken Sie den Stabilisierungsstab in die Bohrungen am Rahmen, wie in der Abbildung Pedal dargestellt. 2. Bringen Sie den Schlegel wie in der Abbildung an der Fumaschine an und stellen Sie ihn mit der Stabilisierungsstab Schlegel-Arretierschraube in einer geeigneten Lnge fest. Nehmen Sie die nachfolgend beschriebenen Einstellungen vor, sofern dies erforderlich ist.
The FP6110 foot pedal attaches to the KP65. First, assemble the pedal as shown in the illustration. 1. Insert the foot board stabilizer rods into the holes on the frame as shown in the illustration. 2. Attach the beater to the pedal as shown in the illustration, and use the beater fixing bolt to secure the beater in a suitable position. If necessary, carry out the adjustments described below. Adjusting the Beater Angle
Beater Head Beater Angle Adjustment Bolt Beater Locking Bolt Spring Roller Belt Frame A Nut B Nut Foot Board Stabilizer Rod

Foot Board

CAUTION
If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur.
See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left.
Checking the contents of the Pad Set and the Trigger Module
Open the DTPK9 (Pad Set) and Trigger Module package and confirm the contents. Figure 6: Pad Set DTLK9
TP65 (Drum Pad) (5) Clamp Bolt (5)
Basic Set Assembly Manual
This manual describes the standard assembly of the DTXPLORER Basic Set. After assembling the parts and connecting the cords as shown in Figure 1, the unit is ready to be turned on. * To assemble the unit, make sure you have the following three packages:
- RS40 (Rack System) - DTLK9 (Pad Set) - DTXPL (Trigger Module)
Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. Do not step on or place heavy objects on the product. It may result in damage. Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration. When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.
Figure 4: Rack Assembly-2
* Prepare beforehand a Phillips screwdriver, required in Mounting the pads and the trigger module on the rack system. Before assembling the unit, lay a drum mat (sold separately). Before assembling the unit, lay a drum mat on the floor. Alternately, to prevent damaging your floor, lay the cardboard box of the included packages, etc. on the floor before assembling the two parts shown in the circles in Figure 1. Figure 1: Unit Standard Assembly
HH65 (Hi-Hat Controller) (1) PCY65 (Cymbal Pad) (2)

KP65 (Kick Pad) (1)

See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90 degrees from pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2 and fix the position of pipe. See Figure 3 again. Loosen the knob (d) on your right. See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction until it is parallel with pipe. Tighten the knob loosened and fix the position of pipe.

FP6110A (Foot Pedal) (1)

Checking the contents of RS40
Open the RS40 (Rack System) package and confirm the contents. Figure 2: RS40 (Rack System)
RS40 (1) Fastening Screw (2) *1
* In the following steps, loosen the knobs first, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed.

Drum Key (1)

q w e r t y u i
DTXPL (Drum Trigger Module) TP65 (Drum Pad) AC Adaptor HH65 (Hi-Hat Controller) PCY65 (Single-zone Cymbal Pad) RS40 (Rack System) KP65 (Kick Pad) FP6110A (Foot Pedal)

Cable Band (10) *2

Assembly Manual (1) *3 - RS40
Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly outward in a counterclockwise direction. Tighten the two knobs loosened and fix the position of pipe. Loosen the two knobs ((f) on the middle left) aligned at the base of pipe. Move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe. Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe outward in a clockwise direction until it is about 45 degrees from pipe. Tighten the two knobs loosened and fix the position of pipe. Check that the entire rack system is stable. Hold the upper area of the vertical pipe and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2 to 5.
9-channel snake cable (1)
Figure 5: Rack Assembly-3
Instruction Manual (4) - TP65/65S - PCY65/65S - HH65 - KP65

PRECAUTIONS

Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device.
*1 Use fastening screws to attach the trigger module in Mounting the pads and the trigger module on the rack system. *2 Use cable bands to bind cables to pipes in Connecting to a power source. (Spare bands are included.) *3 Not this manual.

Figure 7: Trigger Module

DTXPL (1) AC Adaptor (1)

WARNING

If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur.
Assembling the Rack System
Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system.
Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury. Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury. If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. Do not alter the product. Doing so may result in injury or damage/deterioration to the product. Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

The pipe ends may injure your fingers. Figure 3: Rack Assembly-1
10 See Figure 5. Loosen the knobs of the cymbal holders
and on the right and left (shown with on the opposite side of pipe ) and pull up the cymbal holders vertically to the height illustrated. Tighten the knobs loosened and fix the positions of the cymbal holders. Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part. Adjust the Trigger Module attachment part so the operating panel will face upward diagonally to your side when set. Hold the Trigger Module attachment part firmly and turn it gradually. Tighten the two knobs loosened and fix the position of the Trigger Module attachment part.
YAMAHA logo printed on pipe
is facing the opposite side.
Continued on the next page (on the back side)
Mounting the pads and the trigger module on the rack system
Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat.
Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach the felt washer (@3) and the wing nut (@2) removed in step 1, and tighten it. Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely.
Attaching the FP6110A (Foot pedal) to KP65 (Kick pad)
Figure 21: FP6110A and KP65 Figure 22: T-handlet bolt
Figure 28: Diagram of standard connection
Mounting the DTXPL (Trigger module)
Figure 15: Pads Assembly-4 Figure 16: Module stand-1
Mounting the TP65 (Drum pads) on the rack system
Figure 8: Pads Assembly-1 Figure 9: TP65
@5 Module stand @6 Clamp !1 Clamp bolt !2 TP65 (Rear side)
%1 FP6110A (Foot pedal) %2 KP65 (Kick pad) %3 T-handlet bolt 1 Turn the T-handlet bolt (%3) of the foot pedal (%1) in a counterclockwise direction and

loosen it.

Figure 23: Attaching FP6110A

Figure 24: Adjustment

See Figure 16. Loosen the knob of the clamp (@6) (shown with stand (@5) from the clamp (@6).

) and remove the module

See Figure 9. Attach the clamp bolts (!1) on TP65s (!2). Tighten the clamp bolts five to six turns each.
Figure 17: Module stand-2
Figure 10: Pads Assembly-2
%4 %5 %6 %7 Hoop clamp Convex part Beater head Pedal
Attach the convex part (%5) of the kick pad to the hoop clamp (%4). Turn the T-handlet bolt (%3) in a clockwise direction and tighten it. Step on the pedal and check if the head of the beater hits the center area of the kick pad. Adjust the length of the beater and/or position the pedal to the right or left if necessary.

@7 Fastening screw* @8 DTXPL (Rear side)
* The fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system RS40. The plastic bag is packaged between the space within the cardboards used for cushioning.
Tighten the fastening screws (@7) with a Phillips screwdriver, as shown in Figure 17, to attach the module stand (@5) onto the rear side of the trigger module (@8).
Figure 18: Module stand and clamp
Insert the L-shaped plugs (Figure 27-(b)) of the 9-channel snake cable into each corresponding pad. It is recommended to connect the cables in order from numbers q to o shown in Figure 28 (from the shortest cable to the longest cable).
Installing the HH65(Hi-hat controller) and KP65 (Kick pad)
@9 DTXPL + Module stand #0 Clamp #1 Knob
Connecting to a power source
Connect the AC adaptor to the DTXPL. Figure 29: Power switch (DTXPL rear panel)
Figure 25: Hi-Hat and KP65
See Figure 10. Loosen the knob (shown with ) of the tom holder on the middle left. Move the tom holder inward as shown in the close-up illustration (m). Then tighten the knob and attach the tom holder firmly at a position where it points slightly downward.
Attach the module stand (@9) onto the clamp (#0). Tighten the knob (#1) and fix the position.
Figure 11: Tom Holder and Drum Pad
!3 Tom holder !4 Clamp bolt
Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent

scratching the surface.

If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent scratching the surface. Place the HH65 (Hi-hat controller) (^2) under the TP65 (Hi-hat cymbal) (^1). Place the KP65 (Kick pad) with FP6110A (Foot pedal) (^3) at the bottom center of the RS40 (rack system).

Figure 19: KP65 Assembly

^1 TP65 (Hi-hat cymbal) ^2 HH65 (Hi-hat controller) ^3 KP65 (Kick pad)+ FP6110A (Foot pedal)
&1 Power supply jack (DC IN 12V) &2 Cable clip &3 Power switch
Make sure to turn the power off (the Standby/ On switch (&3) is set to the standby position).
Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp bolt and attach the drum pad TP65 firmly. See Figure 10 again. Loosen the knob (shown with ) of the tom holder on the upper left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the knob and attach the tom holder firmly at a position where it points slightly downward. Attach the TP65 (Drum pad) to the tom holder. Tighten the clamp bolt and attach the drum pad TP65 firmly. Repeat step 4 and 5 in the same manner for tom holders and at the center of the rack system and for tom holder on the right, and attach the TP65 (Drum pad) to each tom holder.

Figure 30: Cable clip (DTXPL rear panel)
Connecting the pads to the Trigger Module
Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 26: DTXPL (Rear panel)
#3 #4 #5 #6 #7 Body Base Wing bolt Spring washer Washer
Remove the wing bolt (#5), the spring washer (#6) and the washer (#7) from the body (#3), and keep the four sets nearby in the order removed.
Attach the AC adaptor to connect to a power source. Insert the DC plug into the power supply jack (&1) and twist the cable around the cable clip (&2) to prevent the DC plug from falling out.
Figure 31: Using Cable Band
Mounting the PCY65 (Cymbal pads) on the rack system
Figure 12: Pads Assembly-3 Figure 13: Cymbal holder-1
Figure 27: 9-channel Snake Cable
Use the cable bands to bind the cables to the pipes at the six points shown with the circles.
* If the wing bolt, the spring washer and/or the washer are separated from each other, set them as illustrated in Figure 19-(a).
* Leaving the cable slacked may interfere with your performance.
Set the base (#4) on the body (#3), and attach them using the wing bolt, the spring washer and the washer removed in step 2.
@1 Cymbal holder @2 Wing nut @3 Felt washer See Figure 13. Remove the wing nut (@2) and one of the felt washers (@3) from the cymbal holder (@4).
Assembling the FP6110A (Foot pedal) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent
* Each straight plug is labeled indicating the input jacks to which they are to be connected.
Figure 20: FP6110A Assembly
Insert the straight plugs (Figure 27-(a)) of the 9-channel snake cable into the input jacks on the rear panel of the trigger module. For standard assembly, connect the straight plugs to the input jacks in accordance with the indication on each label.
The assembly is now completed.
To check the actual sound, connect the unit with an amplified speaker or a headphone before turning on the power.
Figure 14: Cymbal holder-2
$1 $2 $3 $4 @4 PCY65 (Cymbal pad) Beater Beater locking bolt Radius rod Drum key
Insert the radius rod ($3) into the hole of the frame as shown in Figure 20. Insert the beater ($1) into the hole of the beater attachment part until the further end of the beater slides outward about 15 mm. Tighten the beater locking bolt ($2) using the drum key ($4).