Wireless G+ MIMO ADSL2+ Modem Router

User Manual

F5D9630-4

Table of Contents

1 Introduction... 1 Advantages of a Wireless Network... 1 Placement of your Wireless G Plus MIMO ADSL2+ Modem Router.Product Overview... 5 Product Features... Knowing your Router... 7 Package Contents... 7 System Requirements... 7 Setup Assistant Software System Requirements.. 7 The Network Status Display... Connecting and Configuring your Router.. Alternate Setup Method... Using the Web-Based Advanced User Interface.. 33 Changing LAN Settings... 34 Viewing the DHCP Client List Page... 35 Configuring the Wireless Network Settings.. 36 Setting WPA Security... 41 Setting WEP Encryption... Manually Configuring Network Settings.. Recommended Web Browser Settings... Troublshooting... Information... 83

Introduction

section
Thank you for purchasing the Belkin ADSL Modem with High-Speed Mode Wireless G Router (the Router). In minutes you will be able to share your Internet connection and network your computers with your new Router. The following is a list of features that make your Router an ideal solution for your home or small office network. Please be sure to read through this User Manual completely, and pay special attention to Appendix B entitled Important Factors for Placement and Setup. Share one high-speed Internet connection with all the computers in your home Share resources, such as files and hard drives among all the connected computers in your home Share a single printer with the entire family Share documents, music, video, and digital pictures Store, retrieve, and copy files from one computer to another Simultaneously play games online, check Internet email, and chat
Advantages of a Wireless Network
Here are some of the advantages of setting up a Belkin Wireless Network: Mobility youll no longer need a dedicated computer room now you can work on a networked laptop or desktop computer anywhere within your wireless range Easy installation Belkins Easy Installation Wizard makes setup simple Flexibility set up and access printers, computers, and other networking devices from anywhere in your home Easy Expansion the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles No cabling required you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office Widespread industry acceptance choose from a wide range of interoperable networking products.
Placement of your Wireless G Plus MIMO ADSL2+ Modem Router
Important Factors for Placement and Setup
Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases. This may or may not be noticeable to you. As you move further from your Router, connection speed may decrease. Factors that can weaken signals simply by getting in the way of your networks radio waves are metal appliances or obstructions, and walls. If you have concerns about your networks performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet from the Router in order to see if distance is the problem. If difficulties persist even at close range, please contact Belkin Technical Support.
Note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help. 1. Router Placement

IP address for Domain Name Server ___. ___. ___. ___ (If given by your ISP)
The Network Status Display
The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The Network Status Display is easily visible on the FRONT of the Router to provide you with information about network activity and status. See the Network Status Display Guide for more detailed information.

Front Panel

(1) 1. Power LED
When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. When the Router has completely booted up, the Power LED becomes a GREEN light, indicating the Router is ready for use. OFF Green Red Router is OFF Router is ON Router failed to start

2. LAN Status LEDs

These LAN Status LEDs are labeled 14 and correspond to the numbered ports on the rear of the Router. When a computer is properly connected to one of the LAN ports on the rear of the Router, the LED will light. Solid GREEN means a computer or a network-enabled device is connected. When information is being sent over the port, the LED blinks rapidly. ORANGE indicates a 10Base-T connection. Orange Orange - blinking Green Green - blinking Ethernet link is up and 10Base-T device connected 10Base-T device is transmitting or receiving data Ethernet link is up and 100Base-T device is connected 100Base-T device is transmitting or receiving data

3. WLAN Status LED

The WLAN Status LED is solid GREEN when you enable the wireless LAN function. It flashes when the Router is transmitting or receiving data wirelessly. Green Green - blinking WLAN is up and connected Transmitting or receiving data

4. ADSL LED

The ADSL LED flashes GREEN during negotiation with your ISP. It stays GREEN when the Router is connected properly to your ADSL service. OFF Green - blinking Green No ADSL connection Negotiating connection ADSL link is up and connected

5. Internet LED

The Internet LED shows you when the Router is connected to the Internet. When the LED is OFF, the Router is NOT connected to the Internet. When the LED is solid GREEN, the Router is connected to the Internet. When the LED is blinking, the Router is transmitting or receiving data from the Internet. OFF Green Green - blinking Red No Internet connection Connected to the Internet Transmitting or receiving data Failed to connect to the Internet

Back Panel (6) (9) (8) (7)

6. DSL Line

This port is for connection to your ADSL. Connect your ADSL to this port.

7. Ethernet Ports

The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router. Connect your network-enabled computers or any networking devices to one of these ports.

8. Reset Button

The Reset button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Routers normal operation while maintaining the programmed settings. You can also restore the factory default settings by using the Reset button. Use the restore option in instances where you may have forgotten your custom password. a. Resetting the Router Push and hold the Reset button for one second, then release it. When the Power/Ready light becomes solid again, the reset is complete. b. Restoring the Factory Defaults Press and hold the Reset button for at least five seconds, then release it. When the Power/Ready light becomes solid again, the restore is complete.

9. Power Plug

Connect the included DC power supply to this inlet. Using the wrong type of power adapter may cause damage to your Router.
Connecting and Configuring your Router
Verify the contents of your box. You should have the following:
Belkin Wireless G Plus MIMO ADSL2+ Modem Router RJ11 Telephone Cord RJ45 Ethernet Networking Cable Power Supply Belkin Setup Assistant Software CD User Manual
Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task. You can use it to get your Router up and running in minutes. The Setup Assistant requires that your Windows 2000 ,XP or Vista computer be connected directly to your ADSL and that the Internet connection is active and working at the time of installation. If it is not, you must use the Alternate Setup Method section of this User Manual to configure your Router. Additionally, if you are using an operating system other than Windows 2000,XP, or Mac OS X you must set up the Router using the Alternate Setup Method section of this User Manual.
Step 1A: Hardware Connections Follow the Quick Installation Guide (QIG) Brand-New Setup

Note for Windows Users: If the Setup Assistant does not start up automatically, select your CD-ROM drive from My Computer and double-click on the file named SetupAssistant to start the Setup Assistant. NOTE TO MAC USERS: Double-click on the Easy Install icon to start
the Setup Assistant. Then, follow the prompts to complete the setup. 2.3 Select Country. Select your country from the drop-down box. Click Begin to continue.
2.4 Confirmation Screen. Verify that you have completed all QIG steps by checking the box to the right of the arrow. Click Next to continue.
2.5 Progress Screen. Setup Assistant will show you a progress screen each time a step in the setup has been completed.
2.6 Checking Settings. The Setup Assistant will now examine your computers network settings and gather information needed to complete the Routers connection to the Internet.
2.7 Verifying Hardware Connections. The Setup Assistant will now verify your hardware connection.
2.8 Naming your Wireless Network. The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect. You can either use the default or change it to something unique. Write down this name for future reference. Click Next to continue.
2.9 Requesting Internet Account Info (if needed). If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below. Select your country or ISP from the drop-down boxes.
2.10 Configuring the Router. The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions.
Note: Do not disconnect any cable or power off the Router while the Router is rebooting. Doing so will render your Router inoperable.
2.11 Checking Internet Connection. We are almost done. The Setup Assistant will now check your connection to the Internet.
Congratulations You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website. You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking Next. If you decide to add computers to your Router later, select Exit the Assistant and then click Next.

Troubleshooting

If the Setup Assistant is not able to connect to the Internet, you will see the following screen. Follow the on-screen instructions to go through the troubleshooting steps.
2.12 Optional: Assistance Connecting Other Computers
This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.

Connection Type

From the Connection Type page, you can select one of these five connection types based on the instruction provided by your ISP: PPPoE PPPoA Dynamic IP (1483 Bridged) Static IP (IPoA) Modem Only (Disable Internet Sharing)
Select the type of connection you use by clicking the radio button (1) next to your connection type and then clicking Next (2).
Setting your ISP Connection Type to PPPoE or PPPoA
PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices. It requires a user name and password to access the network of your ISP for connecting to the Internet. PPPoA (PPP over ATM) is similar to PPPoE, but is mostly implemented in the UK. Select PPPoE or PPPoA and click Next. Then enter the information provided by your ISP, and click Apply Changes to activate your settings.
(1) (2) (3) (4) (5) (6) (7) (8) (9)
1. User Name - Enter the user name (assigned by your ISP). 2. Password - Enter your password (assigned by your ISP). 3. Retype Password - Confirm the password (assigned by your ISP). 4. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier. (VCI) parameter here (assigned by your ISP). 5. Encapsulation - Select your encapsulation type (supplied by your ISP) to specify how to handle multiple protocols at the ATM transport layer. VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation) allows only one protocol running per virtual circuit with fewer overheads. LLC: PPPoA Logical Link Control allows multiple protocols running over one virtual circuit (more overhead). 6. MTU Enter the MTU value for your ISP. 7. Dial on Demand - By selecting Dial on Demand, your Router will automatically connect to the Internet when a user opens up a web browser. 8. Idle Time (Minutes) - Enter the maximum idle time for the Internet connection. After this time has been exceeded, the connection will be terminated. 9. Use Static Default Route Check this box and use the static IP address your ISP assigns for your line. Use this option only if instructed by your ISP.
Click Apply Changes/Next to save and activate your settings. To go back to the original settings before saving, click Clear Changes; or click any of the quick-navigation links for other options. Your new settings will not be saved unless you click Apply Changes/Next.

(1) (2) (3) (4)

Using the Web-Based Advanced User Interface
You will see the Routers home page in your browser window.
Using your Internet browser, you can access the Routers Web-Based Advanced User Interface. In your browser, type 192.168.2.1 (do not type in anything else such as http:// or www) then press the Enter key.

Viewing the LAN Settings

Clicking on the header of the LAN tab (1) will take you to the LAN tabs header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on LAN Settings (2) or to view the list of connected computers, click on DHCP client list (3).

Changing LAN Settings

All settings for the internal LAN setup of the Router can be viewed and changed here.
1. IP Address The IP address is the internal IP address of the Router. The default IP address is 192.168.2.1. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click Apply Changes. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are: 192.168.x.x (where x is anything between 0 and 255) 10.x.x.x (where x is anything between 0 and 255) 2. Subnet Mask There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is 255.255.255.0. 3. DHCP Server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is On. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select Off and click Apply Changes.
4. IP Pool The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address. 5. Lease Time The length of time the DHCP server will reserve the IP address for each computer. We recommend that you leave the lease time set to Forever. The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer. Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time. This also means that a particular computers IP address may change over time. If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change. 6. Local Domain Name The default setting is Belkin. You can set a local domain name (network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network anything you want such as MY NETWORK.

Changing the Wireless Channel
There are a number of operating channels from which you can choosein the United Kingdom (and most of Europe) and Australia, there are 13. In other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country in which you reside. The channel can be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks.
Using the Wireless Mode Switch
This switch allows you to set the Routers wireless modes. There are several modes.
Note: Some modes may require firmware updates to be enabled. 1) 802.11g + 802.11b
Setting the Router to this mode will allow 802.11g- and 802.11bcompliant devices to join the network. 802.11g devices will operate at the 802.11b speed only 2) 802.11g only Setting the Router to this mode will allow only 802.11g-compliant devices to join the network, keeping out 802.11b devices.
Using the Broadcast SSID Feature Note: This advanced feature should be employed by advanced users only. For security, you can choose not to broadcast your networks SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, remove the check mark from the box next to Broadcast SSID, and then click Apply Changes. The change is immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of ANY will no longer be accepted. Refer to the documentation of your wireless network adapter for information on making this change. Changing the Wireless Security Settings
Your Router is equipped with the latest security standard called Wi-Fi Protected Access 2 (WPA2). It also supports the legacy security standard called Wired Equivalent Privacy (WEP). By default, wireless security is disabled. To enable security, you will need to determine which standard you want to use. To access the security settings, click Security on the Wireless tab.
The Router features WPA2, which is the second generation of the WPAbased 802.11i standard. It offers a higher level of wireless security by combining advanced network authentication and stronger Advanced Encryption Standard (AES) encryption methods.
WPA2 Requirements IMPORTANT: In order to use WPA2 security, all your computers and
wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manuals publication, a couple security patches are available, for free download, from Microsoft. These patches work only with the Windows XP operating system. Other operating systems are not supported at this time. For Windows XP computers that do not have Service Pack 2 (SP2), a file from Microsoft called Windows XP Support Patch for Wireless Protected Access (KB 826942) is available for free download at http://support. microsoft.com/?kbid=826942 For Windows XP with Service Pack 2, Microsoft has released a free download to update the wireless client components to support WPA2 (KB893357). The update is available from: http://support.microsoft.com/ default.aspx?scid=kb;en-us;893357

Setting MAC-Address Control
The MAC-address filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter a name for the user and the MAC address of each client on your network to allow network access. Next, click Add to save the settings.
Enabling the Demilitarized Zone (DMZ)
The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.
To put a computer in the DMZ, enter the last digits of its IP address in the IP field and select Enable. Click Apply Changes for the change to take effect. If you are using multiple static WAN IP addresses, it is possible to select which WAN IP address the DMZ host will be directed to. Type in the WAN IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, select Enable and click Apply Changes.

Blocking an ICMP Ping

Computer hackers use what is known as pinging to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Routers security level.
To turn off the ping response, select Block ICMP Ping (1) and click Apply Changes. The Router will not respond to an ICMP ping.

Security Log

The security log shows detailed system-monitoring information. Users can click the Save button to store the log as a text file for later reference purposes. The Refresh button refreshes the page with any new logs and the Clear button clears the page of any existing logs.

Utilities

The Utilities screen lets you manage different parameters of the Router and perform certain administrative functions.

Restarting the Router

Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings.

manage the Router. By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router. The second method is to allow a specific IP address only to remotely manage the Router. This is more secure, but less convenient. To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select Only this IP address can remotely manage the Router. Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password. Leaving the password empty will potentially open your Router to intrusion. Advanced Feature: The Remote Access Port option allows you to configure the desired Remote Access Port for Remote Management feature. The default access port is set to port 80.

Enabling/Disabling UPnP

UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Routers firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports. An application that is UPnP-compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured. The Router ships with the UPnP feature disabled. If you are using any applications that are UPnPcompliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature. Simply select Enable in the UPnP Enabling section of the Utilities page. Click Apply Changes to save the change.
Enabling/Disabling Auto Firmware Update
This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available. When you log into the Routers advanced interface, the Router will perform a check to see if new firmware is available. If so, you will be notified. You can choose to download the new version or ignore it.
Manually Configuring Network Settings
Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet.

6. If not already selected, select Obtain an IP address automatically (1) and Obtain DNS server address automatically (3). Click OK. Your network settings are now configured for use with the Router.
5. If Use the following IP address (2) is selected, your Router will need to be set up for a static IP connection type. Write the address information the table below. You will need to enter this information into the Router.
Manually Configuring Network Settings in Windows 98 or Me
1. Right-click on My Network Neighborhood and select Properties from the drop-down menu. 2. Select TCP/IP -> settings for your installed network adapter. You will see the following window.
3. If Specify and IP address is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 4. Write the IP address and subnet mask from the IP Address tab (3). 5. Click the Gateway tab (2). Write the gateway address down in the chart. 6. Click the DNS Configuration tab (1). Write the DNS address(es) in the chart.
7. If not already selected, select Obtain IP address automatically on the IP address tab. Click OK. Restart the computer. When the computer restarts, your network settings are now configured for use with the Router.
Recommended Web Browser settings
Recommended Web Browser Settings
In most cases, you will not need to make any changes to your web browsers settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browsers settings to the recommended settings in this section.
Microsoft Internet Explorer 4.0 or Higher
1. Start your web browser. Select Tools then Internet Options.
2. In the Internet Options screen, there are three selections: Never dial a connection, Dial whenever a network connection is not present, and Always dial my default connection. If you can make a selection, select Never dial a connection. If you cannot make a selection, go to the next step.
3. Under the Internet Options screen, click on Connections and select LAN Settings. 4. Make sure there are no check marks next to any of the displayed options: Automatically detect settings, Use automatic configuration script, and Use a proxy server. Click OK. Then click OK again in the Internet Options page.
Netscape Navigator 4.0 or Higher
1. Start Netscape. Click on Edit then Preferences. 2. In the Preferences window, click on Advanced then select Proxies. In the Proxies window, select Direct connection to the Internet.

4. Try shutting down and restarting your computer, then rerunning
the Setup Assistant. If the Setup Assistant is still unable to find the Router, reference the section titled Manually Configuring Network Settings for installation steps.
Setup Assistant cannot connect my Router to the Internet.
If the Setup Assistant is not able to connect the Router to the Internet, please check the following items:
1. Use the troubleshooting suggestions within the Setup Assistant. 2. If your ISP requires a user name and password, make sure that
you have typed in your user name and password correctly. Some user names require that the ISPs domain may be at the end of the name. Example: myname@myisp.com. The @myisp.com part of the user name may need to be typed as well as your user name. If you continue to have no Internet connection, reference the section titled Manually Configuring Network Settings (page xx of this User Manual for an alternative setup method).
The Setup Assistant completed installation, but my web browser doesnt work. I am unable to connect to the Internet. The ADSL LED on my Router is off, and the Internet LED is blinking.
If you cannot connect to the Internet, and the ADSL LED is off,
and the Internet LED is blinking, the problem may be that your modem and Router are not connected properly.
1. Make sure the network cable between the modem and the
Router is connected. The cable should be connected at one end to the Routers DSL Line port, and at the other end to the network port on your modem.
2. Unplug the cable or DSL modem from its power source for three
minutes. After three minutes, plug the modem back into its power source. This may force the modem to properly recognize the Router.
3. Unplug the power to your Router, wait 10 seconds, and then
reconnect the power. This will cause the Router to reattempt communication with the modem. If the ADSL LED on the Router is not lit after completing these steps, please contact Belkin Technical Support.
4. Try shutting down and restarting your computer. Problem:
The Setup Assistant completed installation, but my web browser doesnt work. I am unable to connect to the Internet. The ADSL LED on my Router is on, and the Internet LED is blinking.
Solution: 1. If you cannot connect to the Internet, the ADSL LED is on,
and the Internet LED is blinking, the problem may be that your connection type may not match the ISPs connection.
2. If you have a static IP address connection, your ISP must
assign you the IP address, subnet mask, and gateway address. Please refer to the section entitled Alternate Setup Method for details on changing this setting.
3. If you have a PPPoE connection, your ISP will assign you a
user name and password and sometimes a service name. Make sure the Routers connection type is configured to PPPoE and the settings are entered properly. Please refer to the section entitled Alternate Setup Method for details on changing this setting.

connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property, go to the Windows Control Panel, open Network Connections and double-click on your wireless cards connection. In the properties dialog, select the Configure button on the General tab (Windows 98 users will have to select the wireless card in the list box and then click Properties), then choose the Advanced tab and select the rate property. Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment. Note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless cards user manual.
I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Belkin Router.
Solution: 1. Log into your Router.
Open your web browser and type in the IP address of the Router. (The Routers default is 192.168.2.1.) Log into your Router by clicking on the Login button in the top right-hand corner of the screen. You will be asked to enter your password. If you never set a password, leave the Password field blank and click Submit. Click the Wireless tab on the left of your screen. Select the Encryption or Security tab to get to the security settings page.
2.Select 128-bit WEP from the drop-down menu. 3. After selecting your WEP encryption mode, you can type in your
hex WEP key manually, or you can type in a passphrase in the Passphrase field and click Generate to create a WEP key from the passphrase. Click Apply Changes to finish. You must now set all of your clients to match these settings. A hex (hexadecimal) key is a mixture of numbers and letters from A-F and 0-9. For 128-bit WEP, you need to enter 26 hex keys. For example: C0F AF 4B B2 C3 D4 4B C3 D4 E7 E4 = 128-bit key
4.Click Apply Changes to finish. Encryption in the Router is now
set. Each of your computers on your wireless network will now need to be configured with the same security settings. WARNING: If you are configuring the Router from a computer with a wireless client, you will need to ensure that security is turned on for this wireless client. If this is not done, you will lose your wireless connection. Note to Mac Users: Original Apple AirPort products support 64bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption. Please check your Apple AirPort product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption.

I am having difficulty setting up Wireless Protected Access (WPA) security on my Belkin Router for a home network.
Solution: 1. From the Security Mode drop-down menu, select WPA-PSK

(no server).

2. For Encryption Technique, select TKIP or AES. This setting
will have to be identical on the clients that you set up.
3. Enter your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, symbols, or spaces.
This same key must be used on all of the clients that you set up. For example, your PSK might be something like: Smith family network key.
4. Click Apply Changes to finish. You must now set all clients to

match these settings.

I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network.
Clients must use the same key that the Router uses. For instance, if the key is Smith Family Network Key in the Router, the clients must also use that same key.
Network screen. The Advanced button will allow you to view and configure more options of your card.
2. Once the Advanced button is clicked, the Belkin Wireless
3. Under the Wireless Network Properties tab, select a
network name from the Available Networks list and click the Properties button.
4. Under Network Authentication, select WPA-PSK (no server). 5. Type your WPA key in the Network key box.
Important: WPA-PSK is a mixture of numbers and letters from A-Z and 0-9. For WPA-PSK you can enter eight to 63 characters. This network key needs to match the key you assign to your Router.
6. Click OK, then Apply to save the settings.
I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security.
If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called Windows XP Support Patch for Wireless Protected Access is available for free download. Download the patch from Microsoft by searching the knowledge base for Windows
XP WPA. Note: The file that Microsoft has made available works only with Windows XP. Other operating systems are not supported at this time. You also need to ensure that the wireless cards manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site. Supported Operating Systems: Windows XP Professional Windows XP Home Edition
1. Under Windows XP, click Start > Control Panel > Network

Connections.

2. Right-click on the Wireless Networks. Ensure the Use
Windows to configure my wireless network settings check box is checked.

Self Help Guide

A Guide To Wireless Bridging (WDS)
Please read the following carefully;

IMPORTANT!

This Guide refers to the following Products:
Synopsis: The following Guide is designed to give you an understanding of what is meant by the terms Wireless Bridge and WDS. This Guide will also provides a graphical overview as to which Belkin Devices support this feature, and then go on to explain how this feature is activated and configured.
Requirements: In order to complete the steps as outlined in this Guide and set up a functioning Wireless Bridge you will need the following equipment as a basic minimum;
Please Refer To Page 3 For Full List Of WDS Capable Devices
At least 2 of the Devices listed on Page 3 At least one PC with either LAN or WLAN working
This is the minimum required to configure and test the Wireless Bridge to ensure that it is functioning correctly. The amount of equipment required thereafter is dependent on the individual Network requirements.
TSG-UK-1-001 TSG-UK-1-011

www.belkin.com

1 Page 1 of 5
A Wireless Bridge is the name commonly given to the relationship that is formed (wirelessly) between two Infrastructure Devices such as Access Points and Routers. The primary function of a Wireless Bridge is to extend the range of an existing Wireless Local Area Network (WLAN). Wireless Bridging is based on the Wireless Distribution System (WDS) which allows you to make a completely wireless infrastructure. Normally, Access Points must be hardwired to an Ethernet-based LAN. In this way the Access Points allow for a wireless connection to be made to the wired network. The WDS feature allows Infrastructure Devices such as Access Points and Routers to be wirelessly connected to one another. This feature is normally used in large, open areas such as warehouses where wiring might be restricted or not cost effective, and in some larger home environments. Wirelessly Bridging multiple Devices that have all been configured to use the same SSID (Service Set Identifier or Wireless Network Name) will allow in effect Roaming for your Wireless Client Adapters. When they are out of range of one device they will automatically connect to another stronger signal. Wireless Bridges are a very practical, easy, and in most cases inexpensive way to connect two different Ethernet LANs together or extend the range of existing Wireless Networks. They are quick to set up and relatively easy to configure.
Note: The WDS feature is not completely specified in IEEE or WiFi standards. Therefore interoperability between 802.11 products of different Vendors is not guaranteed. We can only recommend and advise on setting up a Wireless Bridge between the Belkin Devices listed on the following page. Please take care to note the Version of the Hardware as well as the Model Number as this may change the nature of the devices compatibility with WDS. The WPA encryption type is not supported over a Wireless Bridge and in such instances WEP is the compatible encryption type.
TSG-UK-1-011 TSG-UK-1-001

Page 1 of 5

Wireless Bridging (WDS) Compatible Devices

F5D7130 v.1*

F5D7130 v.2

F5D7230 v.1*

F5D7230 v.2

F5D7230 v.4*

F5D7230 v.6

F5D7231 v.1xxx**

F5D7231 v.2xxx**

F5D7231-4P**

F5D7235**

F5D7632 v.3 &4

F5D7632 v.5 & 6

F5D7633**

F5D9630 v.3

F5D9630 v.4

Ensure Unit is updated to latest Firmware Version available ** Ensure Unit is updated to latest Firmware Version where applicable and that 125 HSM Mode is disabled.
Configuring Your Device To Enable Wireless Bridging
All the Devices listed on the previous page offer the option for Wireless Bridge in the Menu of the User Interface, under the heading Wireless. Once selected you will see a page similar to that listed below;
Please note the restrictions outlined on this page including the need to have all your Wireless Devices using the same Wireless Channel (1-13) and the same Encryption Key. The only supported Encryption Type is WEP. To enable Wireless Bridging simply tick the first two boxes shown above, Enable Wireless Bridging and Enable Only Specific Access Points To Connect You will then need to manually enter details regarding the Device you wish to bridge with. TSG-UK-1-011 TSG-UK-1-001 | www.belkin.com | Page 1 of 5

The Wireless Networking Device that you are wishing to bridge with has a unique WLAN MAC Address that needs to be located (see Product Label) and entered into the Interface of the device being used to set up the bridge as shown in the example below. Please ensure that the WLAN MAC Address from the Product Label is used, and not the LAN MAC Address which is also to be found there.
Once the WLAN MAC Address of the Bridge Device has been entered and the new settings applied, the Wireless Bridge should be functioning, and a Wireless connection should now be possible between the two devices. The connection can be tested by either Pinging one device from the other or by opening the User Interface of the newly bridged Device. A Device restart may be required. Please note that the F5D7633 is configured in much the same way but the relevant page of the User Interface looks somewhat different and the MAC Address is entered as shown below;

00:11:50:12:34:56

The F5D7633 also offers an Auto discovery option under Wireless Bridge which will essentially display a list of Devices on the same Wireless Channel as your main Device that you can choose from. Their MAC Addresses will all be shown and all you have to do is select the ones youd like to bridge with by ticking the appropriate boxes.