User Manual - AirStation Draft-N WZR2-G300N Wireless Router & AP

www.buffalotech.com

Table of Contents
Introduction. 3 Initial Setup. 4 Configuration Tool Login. 8 Connecting Wireless Clients. 10 Using the Configuration Tool. 11 AOSS. 15 Router/Access Point Mode Switch. 17 Encryption and Security . 18 Connecting to an Existing Network. 23 Specifications . 24 Troubleshooting. 27 Glossary. 30 FCC Information. 37 Warranty. 43 Contact Information (USA). 44 Contact Information (Europe). 45 GPL Information (USA). 46 GPL Information (Europe). 47

Introduction

Work and play - further and faster! Your AirStation Nfiniti combines Ethernet networking with extended wireless range and speed. It offers excellent compatibility with most wireless clients, giving superb performance with Wireless-N, Wireless G, and legacy Wireless-B clients. For best overall performance, use with Buffalo Technology Nfinity wireless clients. System Requirements:
A high-speed (Broadband) Internet connection or existing local area connection. A computer with a network connection (wired or wireless) and a good web browser. The screenshots in this manual were taken with Firefox, but Netscape and Internet Explorer are also supported in versions 4.5 or later, and Safari 1.0 and later are supported with Macintosh OS X 10.2 and later.

Package Contents:

WZR2-G300N AirStation with built-in antennas AC adapter CAT5 LAN cable Utility CD with Manual Quick Setup Guides Warranty Statement

Initial Setup Begin

by finding a good place to set up your router/access point. Some things to consider: Youll need to be able to plug your internet connection into it, so it should go within reach of the LAN cable from your DSL or Cable modem. Youll also want a power outlet nearby. Keep the access point as central in your work area as possible. Signal strength and speed fall off with distance. Higher is often better. For instance, set it up on the top shelf of a bookcase rather than the bottom one, if possible. Do you need a password or other information to log in to your internet connection? Many DSL connections require information like global IP address, subnet mask, default gateway address, DNS server address, or PPPoE parameters in order to connect. Cable modems usually dont require extra information. If you have a DSL internet connection, make sure that you have any necessary information handy before you continue. Your Internet Service Provider can give you this information if you dont know it.
Placing Your AirStation Your AirStation may be placed horizontally or mounted vertically on a wall.
The antennas will usually work best if oriented vertically.
For wall mounting, screw three screws into the wall as shown below.

9 cm (~3.5 inches)

8.5 cm (~3.3 inches)

(Drawing not to scale.)

Connecting your AirStation
Power to outlet or power strip

Cable or DSL Modem

Initial Setup
To initially configure your router, youll use a wired connection to your computer. Once youve connected to the internet through the router, you may switch to a wireless connection if desired. The computer used to configure the AirStation should be set to obtain an IP address automatically using a DHCP server (this is the default). The WZR2-G300N has a default LAN IP address of 192.168.11.1 and Subnet Mask of 255.255.255.0. 1. Power down the Cable or DSL modem and the computer which will be used to configure the AirStation router. 2. Plug the Cable or DSL modems Ethernet cable into the AirStations WAN port. Initially, you may need to unplug this cable from your computer, hub or other router. 3. Plug the provided Ethernet cable into a LAN port on the AirStation and plug the other end into your computers Ethernet adapter (NIC). 4. Important: turn everything on in the correct order!! Power on your cable or DSL modem and wait one full minute, then power on the AirStation router and wait one full minute, and finally power on the computer which will be used to configure the AirStation.

Help and Instructions

The following pages show examples of some screens from the configuration utility.

Initialize/Reboot

The Initialize/Restart page can be reached by choosing the Admin Config catagory tab and then clicking on the Initialize/Restart submenu. Click Restart Now from this page to restart your AirStation. Click Initialize Now to restore your AirStation to factory defaults and restart it.
You may also initialize your AirStation by holding down the Reset button for 3 seconds.
You can get to this page by selecting the Wireless Config category and choosing the AOSS submenu. The blue AOSS button at the top left of the page has the same function as the physical AOSS button on the top of the router: it initiates the AOSS process. If all your clients support AOSS, its very simple to set them up. Press the AOSS button on the router, or the one on this page, and then push the AOSS button on the client device. Each client device will have to be set up seperately. Wait for each AOSS process to finish before starting the next one. You can also activate AOSS by pushing the button on the top of your AirStation (see page 15). Consult your client devices documentation for the location of its AOSS button. If youve used AOSS to configure some wireless clients, and now want to add other wireless clients that dont support AOSS to your network, this screen will give you the information you need to connect them manually.
AOSS (AirStation One-Touch Secure System) is a simple system for configuring your wireless network securely. If your router and your client device are installed and both support AOSS, then making a secure wireless connection between them is very easy. Push the AOSS button on the top of your router and hold it in for a few seconds. The AOSS light will begin to flash amber. You now have two minutes to push the AOSS button on your client device and finish the connection. If you have a standalone client device, it will probably have a little red button labled AOSS on it. Push the button! About 15 seconds later, youll have a secure network connection. If your client device is a PC card, CardBus, or PCI adaptor, the AOSS button will probably be in its Client Manager Software. Check your client devices user manual for instructions on where to push or click the AOSS button.

standalone client device

PC card

Client Manager Software

After youve pressed both buttons, it will take about 15 seconds for the connection to complete. When its finished, the AOSS light witll glow a solid amber. You now have a secure network connection!

AOSS Notes

Some things to keep in mind with AOSS: Only one AOSS wireless client adapter can be configured with the AOSS router at a
time. The buttons will need to be re-pressed to connect each additional AOSS wireless client adapter. It is not necessary to AOSS client devices that have already been configured via AOSS, unless significant changes have been made to the wireless network. Do not attempt to configure two separate AOSS networks at the same time, as it may cause undesired configurations. If an undesired client has connected via AOSS, it can be disconnected from within the WZR2-G300Ns advanced configuration menus.

Router/Access Point Mode

This AirStation supports quickly changing the product from a full wireless router to a simple access point. Put your Airstation into Access Point Mode by moving the ROUTER switch on the bottom of your AirStation from ON to OFF. This changes the default IP address of the AirStation from 192.168.11.1 to 192.168.11.100, and DHCP, NAT, and the WAN port are disabled. All router functionality is disabled, and the WZR2-G300N becomes a simple access point. Access Point Mode might be desirable if youre adding wireless capability to an existing network that already has a router. It is not suitable for most home configurations where the unit is the only router in the network. If you plan to use the AirStation as a normal wireless router, make sure that this switch is in the normal (ON) position!

Encryption and Security

By default, encryption is not enabled on the AirStation unless you used AOSS to perform your setup. Anyone within range can easily connect to your wireless network. This might not be what you want. Buffalo recommends enabling encryption and setting a password for access to your network. This is easy to configure from within the AirStations configuration tool. From the opening page, select Wireless Config Tab, select the Security submenu.
Many kinds of encryption are available. WEP works with almost everything. WPA2-PSK is much more secure. Choose the strongest method of encryption that works with all of your wireless devices. If you must use WEP, it is available under Wireless Encryption.

Enter a network key (password) for this connection. Write down your password and put it in a safe place. You will not be able to connect wireless devices to your network without this password.
Each of your wireless clients will need your password to connect to the network. Click on the wireless icon in your computers systray, or this message if it pops up.
Any wireless networks available in the area will be listed as available. Click on your wireless network SSID so that it turns blue and then click on Connect at the bottom right.
Connecting your Wireless Clients
Any wireless networks available in the area will be listed as available. Click on your wireless network SSID so that it turns blue and the click on Connect at the bottom right.
Enter your network key (password) twice and click Connect.
Repeat for each Windows XP computer that connects to your network wirelessly.
Other wireless devices may have different configuration requirements. Consult their documentation for instructions on how to enter your network key and connect them to your wireless network.
Connecting to a Preexisting Network
Add an AirStation without changing your existing LAN configuration:
1. Set the AirStation into Access Point Mode by moving the switch from ROUTER to AP. 2. Connect one of the AirStations LAN ports to an existing router or switch on your network. Nothing should be plugged into the WAN (Internet) port. 3. Open LAN Settings - LAN Port Settings and configure the following settings: IP Address =[192.168.11.137] (Specify an unused network address from the existing LAN.) Subnet Mask=[255.255.255.0] (Use the same Subnet Mask as the existing LAN.) DHCP Server Function=[Disable] 4. Restart PC.

Specifications

For more information, FAQs, and updates, consult the AirStation website at http://www.buffalotech.com.
WZR2-G300N AirStation Specifications
Physical Specifications Dimensions 6 x 1.3 x 5.9 (152 x 33 x 150 mm) Weight.68 lb. (308 g) Temperature & Humidity Operation 32 to 104 F, 0 to 40 C Maximum humidity 80% Transit/Storage 0 to 40 C maximum humidity 80% (no condensation) Power Characteristics Power Supply: 100-240V AC Universal, 50/60 Hz. Power Output: 12V DC Power Consumption about 20 Watts (Max)
Regulatory Information Wireless communication is often subject to local radio regulations. Although AirStation wireless networking products have been designed for operation in the license-free 2.4 GHz band, local radio regulations may impose limitations on the use of wireless communication equipment. Network Compatability Draft-N support built off of the Draft Specification 1.0 for 802.11n. IEEE802.11g/b Standard for Wireless LANs. Host Operating System Microsoft Windows 98SE/ME/NT4.0/2000/XP, Unix, Linux and MacOS Media Access Protocol Wired - CSMD/CD (Collision Detection) Wireless - CSMD/CA (Collision Avoidance) with Acknowledgment (ACK)

AirStation IEEE 802.11 Channel Sets The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at a lower Transmit range may travel longer distances. Center Channel ID FCC 11 default channel

Troubleshooting

Common Problems
Out of range, client cannot connect to the AirStation. Configuration mismatch, client cannot connect to the AirStation. Absence or conflict with the Client Driver. Conflict of another device with the AirStation hardware.

LED Activity

Monitoring LED activity helps identify problems. Power LED should be Green, Wireless LED should be Green if the line is active. If is it blinking Green, wireless communication is active. Ethernet LED should be Blue (1000Mbps), Green (100Mbps), or Amber (10Mbps) while the communication is active. The Red Diag LED will flash during boot and firmware updates.

DIAG LED Activity

Unplug the power for three seconds. Plug the power back in to monitor the Diag LEDs during start-up.

DIAG LED Activity Table

DIAG LED Display Continuous Red Red flash, 3 times Red flash, 4 times Time Starting Starting Starting Description/Action RAM Error Red flash, 2 times Starting Flash ROM Error A problem on the wired LAN side A problem on the wireless LAN side
LEDs Work But Client PC Cannot Connect to Network
If the LEDs indicate that the network is working properly (Power LED is on, Transmit/ Receive LED blinks), check the TCP/IP settings of the network.
Changing Client TCP/IP Settings in Windows
Consult the LAN Administrator for correct TCP/IP settings. To add or change TCP/IP Settings: 1. On the Windows task bar, click Start. 2. Select Settings, then Control Panel. 3. Double-click on the Network icon to view Network Properties. 4. From the list of installed components, verify the TCP/IP - wireless LAN adapter protocol is installed.
If the wireless adapter protocol is not yet installed, click the Add button and select the TCP/IP protocol from the list. Refer to Windows Help for more information. If the wireless adapter protocol is installed, select the protocol and click the Properties button. Verify that the parameters match the settings provided by your LAN Administrator. Make changes if necessary, and click OK. 5. If prompted, restart your computer.

Other Problems

Please refer to www.buffalotech.com for further reference materials.

Glossary

10BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 10 Mbps data tansmission speed. 100BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 100 Mbps data tansmission speed. 1000BaseT: 802.3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 1000 Mbps data tansmission speed. 802.1x: The standard for wireless LAN authentication used between an AP and a client. 802.1x with EAP will initiate key handling. Access Point: A hardware device that acts as a communication hub for Clients (users of wireless devices) to connect to a wired LAN. Ad-Hoc Network: A network based on peer-to-peer communication rather than a router, switch, or hub. Bandwidth: The transmission capacity of a computer or a communication channel, usually stated in Megabits per second (Mbps). Bridge: A device which forwards traffic between network segments with a common network layer address, based on data link layer information. Client: A PC, workstation, or other device that connects to a network wirelessly through an Access Point. Cross-Over Cable: A UTP cable that has its transmit and receive pair crossed to allow communications between two devices. Default Gateway: The IP Address of either the nearest router or server for the LAN.

Destination Address: The address portion of a packet that identifies the intended recipient station. DHCP (Dynamic Host Configuration Protocol): Based on BOOTP, it uses a pool of IP addresses, which it assigns to each device connected to it, and retrieves the address when the device becomes dormant for a period of time. DNS (Domain Name System): System used to map readable machine names into IP addresses. Driver: Software that interfaces a computer with a specific hardware device. Dynamic IP Address: An IP address that is automatically assigned to a client station in a TCP/IP network, typically by a DHCP server. Ethernet: The most widely used architecture for Local Area Networks (LANs). It is a shared-media network architecture. The IEEE 802.3 standard details its functionality. Ethernet cable: A wire similar to telephone cable that carries signals between Ethernet devices. It is designed to connect a single devices NIC to a router, switch, or hub. See also Crossover cable. File and Print Sharing: A Microsoft application that allows computers on a network to share files and printers. Firmware: Computer programming instructions that are stored in a readonly memory unit rather than being implemented through software. Frame: A fixed block of data, transmitted as a single entity. Also referred to as a packet.
Full-Duplex: To transmit on the same channel in both directions simultaneously. Half-duplex: To transmit on the same channel in both directions, one direction at a time. Hub: A device which allows connection of computers and other devices to form a LAN. IEEE (Institute of Electrical and Electronics Engineers): The professional organization which promotes development of electronics technology. IP (Internet Protocol) Address: A unique 32-binary-digit number that identifies each sender or receiver of information sent in packets. Infrastructure: A wireless network or other small network in which the wireless network devices are made a part of the network through the Access Point. ISP (Internet Service Provider): A company that provides access to the Internet and other related services. IV (Initialization Vector): The header section of an encrypted message packet. LAN (Local Area Network): A group of computers and peripheral devices connected to share resources. LED (Light Emitting Diode): The lights on a hardware device representing the activity through the ports. MAC (Medium Access Control) Address: The unique number that distinguishes every network interface card. Mbps (Mega Bits Per Second): A measurement of millions of bits per second. MDI/X (Media Dependent Interface/ Cross-over): Port on a network hub or switch that crosses the incoming transmit lines with the outgoing receive lines.
MHz (MegaHertz): One million cycles per second. NAT (Network Address Translation): An internet standard that enables a LAN to use one set of IP addresses for internal traffic and a second set for external traffic. NIC (Network Interface Card): An expansion card connected to a computer so the computer can be connected to a network. Packet: A block of data that is transferred as a single unit, also called a frame or a block. Packet Filtering: Discarding unwanted network traffic based on its originating address or its type. PCI (Peripheral Component Interconnect): A bus that is connected directly to the CPU. PCMCIA (Personal Computer Memory Card International Association) Card: Removable module that adds features to a portable computer. Peer-to-peer: This simple network is formed by connecting computers directly, without use of routers or hubs. A crossover cable is plugged into an Ethernet port in each computer, connecting them directly. Ping (Packet Internet Groper): An Internet utility used to determine whether a particular IP address is accessable. Plug and Play: Hardware that, once physically installed, finishes its installation automatically and may immediately be used, as opposed to hardware that requires further manual configuration. PoE (Power over Ethernet): A mechanism to send DC power to a device using a CAT5 Ethernet cable.

PPPoE (Point-to-Point Protocol over Ethernet): A specification for connecting users on an Ethernet line to the Internet through a common broadband medium. Protocol: A standard way of exchanging information between computers. RADIUS (Remote Authentication Dial In User Service): A server that issues authentication keys to clients. RAM (Random Access Memory): Nonpermanent memory. Repeater Hub: A device that collects, strengthens and transmits information to all connected devices, allowing the network to be extended to accommodate additional workstations. See also Bridge. RC4: The encryption algorithm used by WEP. RJ-45 connector: An 8-pin connector used between a twisted pair cable and a data transmission device.
ROM (Read Only Memory): Memory hardware that allows fast access to permanently stored data but prevents addition to or modification of the data. Router: A device in a network that handles message transfer between computers. Similar to a hub, but with added functionality and efficiency. Roaming: The ability to use a wireless device while moving from one access point to another without losing the connection. Server: Any computer that makes files or peripheral devices available to users of the network and has a resident Network OS. SMTP (Simple Mail Transfer Protocol): The protocol used to define and deliver electronic mail (E-mail) from one location to another.
SNMP (Simple Network Management Protocol: An application layer protocol that outlines the formal structure for communication among network devices. Static IP Address: A permanent IP address is assigned to a node in a TCP/IP network. Also known as global IP. SSID: The name of your wireless network. You can get it from the Setup page of the configuration utility. STP (Shielded Twisted Pair): Twisted Pair cable wrapped in a metal sheath to provide extra protection from external interfering signals. Subnet Mask: An eight-byte address divided into 4 parts separated by periods. TCP/IP (Transmission Control Protocol/ Internet Protocol: Protocol used by computers when communicating across the Internet or Intranet. TKIP (Temporal Key Integrity Protocol): An encryption method replacing WEP. TKIP uses random IV and frequent key exchanges. Topology: The shape of a LAN (Local Area Network) or other communications system. Twisted Pair: Cable that comprises 2 or more pair of insulated wires twisted together. UDP (User Datagram Protocol): A communication method (protocol) that offers a limited amount of service when messages are exchanged between computers in a network. UDP is used as an alternative to TCP/IP. Uplink: Link to the next level up in a communication hierarchy. UTP (Unshielded Twisted Pair) cable: Two or more unshielded wires twisted together to form a cable.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important Note: CC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and persons body (excluding extremities: hands, wrists, feet and legs). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

European Union Notice:

Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN 60950 Product Safety EN Technical requirement for radio equipment EN 301 489-1/-17 General EMC requirements for radio equipment

Taiwan:

SAR compliance has been established in typical laptop computer(s) with CardBus slot, and product could be used in typical laptop computer with CardBus slot. Other application like handheld PC or similar device has not been verified, may not comply with related RF exposure rules, and such use shall be prohibited.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.

Intended use

This device is a 2.4 GHz & 5 GHz wireless LAN transceiver, intended for indoor home and office use in USA, Canada, all EU and EFTA member states.
EU Countries intended for use
This device is intended for indoor home and office use in the following countries: Austria, Belgium, Denmark, France, Finland, Germany, Greece, Italy, Ireland, Luxembourg, The Netherlands, Portugal, Spain, Sweden, United Kingdom, Cyprus, Czech Republic, Estonia, Hungry, Latvia, Lithuania, Malta, Poland, Slovak Republic, and Slovenia. The device is also authorised for use in all EFTA member states Iceland, Liechtenstein, Norway and Switzerland.
EU countries not intended for use
Potential restrictive use
France: Only channels 10,11,12, and 13.
This device is a 2.4 GHz & 5 GHz wireless LAN transceiver, intended for indoor home and office use in all EU and EFTA member states, except in France, Belgium and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain an authorization to use the device for setting up outdoor radio links. In Belgium there is a restriction in outdoor use. The frequency range in which outdoor operation in Belgium is permitted is 2460 2483.5 MHz. In France only channels 10,11,12 and 13 are available. This device may not be used for setting up outdoor radio links in France. For more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr
Environmental Information
The equipment that you have purchased has required the extraction and use of natural
resources for its production.
The equipment may contain hazardous substances that could impact health and the

environment.

In order to avoid the dissemination of those substances in our environment and to diminish the The take-back systems will reuse or recycle most of the materials of your end life equipment in

a sound way.

pressure on the natural resources, we encourage you to use the appropriate take-back systems.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems, please contact your local or regional waste administration.

Warranty Information

Buffalo Technology (Melco Inc.) products come with a two-year limited warranty from the
date of purchase. Buffalo Technology (Melco Inc.) warrants to the original purchaser the product; good operating condition for the warranty period. This warranty does not include non-Buffalo Technology (Melco Inc.) installed components. If the Buffalo product malfunctions during the warranty period, Buffalo Technology/(Melco Inc.) will, replace the unit, provided the unit has not been subjected to misuse, abuse, or non-Buffalo Technology/(Melco Inc.) authorized alteration, modifications or repair. All expressed and implied warranties for the Buffalo Technology (Melco Inc) product line including, but not limited to, the warranties of merchantability and fitness of a particular purpose are limited in duration to the above period. Under no circumstances shall Buffalo Technology/(Melco Inc.) be liable in any way to the user for damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use the Buffalo products. In no event shall Buffalo Technology/(Melco Inc.) liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. Buffalo Technology (Melco Inc.) does not offer refunds for any product. @ 2003-2007 Buffalo Technology (Melco, Inc.)

Contact Information

Buffalo Technology (USA), Inc. 4030 West Braker Lane, Suite 120 Austin, TX 78759-5319

GENERAL INQUIRIES

Monday through Friday 8:30am-5:30pm CST Direct: 512-794-8533 | Toll-free: 800-456-9799 | Fax: 512-794-8520 | Email: sales@buffalotech.com

TECHNICAL SUPPORT

North American Technical Support by phone is available 24 hours a day, 7 days a week. (USA and Canada). Toll-free: (866) 752-6210 | Email: info@buffalotech.com
Buffalo Technology UK Ltd. 176 Buckingham Avenue, Slough, Berkshire, SL1 4RD United Kingdom
Email: sales@buffalo-technology.com
Phone (UK only): 12 60* Phone: +50 Email: helpdesk@buffalo-technology.ie *Calls cost 8.5p per minute Technical Support Operating Hours Monday - Friday (GMT) 9:00 AM - 6:00 PM Monday-Thursday 9:00 AM - 4:30 PM Friday
GPL Information (North America)
Thank you for your interest in Buffalo products. Our GPL software delivery policy is outlined below. For each individual product and revision, please send one individually packaged self addressed padded CD shipping envelope, containing a blank CD-R to the following address: Buffalo Technology USA Inc. 4030 W. Braker Lane Suite 120 Austin, TX 78759 Attn. GPL Department Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft or money order for $20 (USD) (Made out to: Buffalo Technology) to cover our handling fee, postage and CD preparation. The CD-R should have the name of the product and revision number clearly written on the actual CD-R (not on the insert). We do not send GPL source in bulk on a DVD. And order confirmation is not required by the GNU General Public License. We are more than happy to comply with your request; however, we must ask you to comply with our GPL distribution policy, which complies with the GNU General Public License. Sincerely, Buffalo Technology GPL Department

GPL Information (Europe)

Thank you for your interest in Buffalo products. Our GPL software delivery policy is outlined below. For each individual product and revision, please send one individually packaged self addressed padded CD shipping envelope, containing a blank CD-R to the following address: Buffalo Technology Ireland Ltd Free Zone East, Shannon, Co. Clare Ireland Attn. GPL Department Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft or money order for 20 (Euro) (Made out to: Buffalo Technology) to cover our handling fee, postage and CD preparation. The CD-R should have the name of the product and revision number clearly written on the actual CD-R (not on the insert). We do not send GPL source in bulk on a DVD. And order confirmation is not required by the GNU General Public License. We are more than happy to comply with your request; however, we must ask you to comply with our GPL distribution policy, which complies with the GNU General Public License. Sincerely, Buffalo Technology GPL Department

300* High Speed Mode

*300 Mbps is the link speed when using Draft-N mode. It represents actual wireless data speeds, including overhead. Because the overhead is not available for user data transfer, usable wireless throughput will be substantially slower.