Sipura SPA 2002 How To
(c) 2003-2010 Bicom Systems
All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document. Printed: avgust 2010
Publisher. Managing Editor. Technical Editors.. Cover Designer. Team Coordinator. Production.

Special thanks to:

Table of Contents

Foreword I

Part I Introduction Part II Registering Sipura SPA 2002
1 Requirements..... Manual Configuration..... 6
UAD Settings..... 6 Creating Extension..... 8 Registering ATA..... 10
3 Auto Provisioning..... 13
UAD Settings..... 13 Creating Extension..... 16 Registering ATA..... 18 LAN And WAN IP Address..... 21
4 Auto Configuration..... 22
Requriem..... 23 ents Auto Configuration..... 23

Part III Glossary Index

Foreword

Introduction

Sipura SPA 2002
How to use the Sipura SPA 2002 with PBXware
This "How to" is written as a general guide on how to use your Sipura SPA 2002 with PBXware using 3.1.5 Sipura SPA 2002 firmware. It covers the most common tasks required to have your Sipura SPA 2002 working efficiently.
Registering Sipura SPA 2002
Requirements Manual Configuration Auto Provisioning Auto Configuration

Requirements

1. Sipura SPA 2002 firmware. - Make sure the device is loaded with 3.1.5 firmware. 2. DHCP server. - Fully configured and operational DHCP server. 3. Sipura SPA 2002 Dial Plan. - The Sipura SPA 2002 "Dial Plan" field value needs to be changed using web interface. STEP ONE: Sipura SPA 2002 Web Interface. 1. Open a new browser window and enter the IP address in order to access the Sipura SPA 2002 administration interface. Example: http://192.168.1.101 To learn how to find out your Sipura SPA 2002 IP Address go to chapter "Registering ATA" "STEP TWO".
an example with IP address 2. Hit "Enter" on your keyboard. STEP TWO: Sipura SPA 2002 Dial Plan field value. 1. Click on the "Admin Login" link.
2. Click on "advanced" link.
3. Click on "Line 1" link.
4. Navigate down to "Dial Plan" group. Clear the "Dial Plan" field, then copy and paste the following value. (*x.|**x.|*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxx| xxxxxxxxxxxx.)
5. Click on the "Submit All Changes" button. The Sipura SPA 2002 will reboot for changes to take effect.

Manual Configuration

- UAD Settings - Creating Extension - Registering ATA

UAD Settings

STEP ONE: PBXware IP address. 1. Find out the IP address of the PBXware server. STEP TWO: Login to PBXware. 1. Open a new browser window and enter the IP address to access the PBXware administration interface login screen. Example: http://192.168.1.2
an example with IP address 2. Hit "Enter" on your keyboard. 3. Login to PBXware with your e-mail address and password.

STEP THREE: UAD status.

1. Make sure the UAD is enabled. To check the UAD status, navigate to "Settings:UAD", and click on the "edit" icon corresponding to "Sipura SPA 2002".
2. Make sure "Status" is set to "active", "Auto provisioning" is set to "No", and "DHCP" is set to "Yes".
3. Click on the "Save" button to save changes.

Creating Extension

STEP ONE: Add Extension. 1. Navigate to "Extensions". Click on "Add Extension".
2. The standard options window (below) will be shown.
3. Select the Sipura SPA 2002 from the "UAD" select box. 4. Select Location: "Local" or "Remote".
Note: -"Local" is for all extensions registered on LAN. -"Remote" is for all extensions registered from remote networks, WAN, Internet etc.
5. Click on the "Next" button. STEP TWO: Extension values. 1. Enter values into the required field text boxes. REQUIRED FIELDS: Name: Enter a name for the extension being created. Example: John Smith. E-mail: Enter the e-mail address associated with this extension. This e-mail address will receive all system notification messages. Example: john@domain.com.
an example with details filled in 2. Click on the "Save" button.
an example with details filled in 3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address associated with this extension. OPTIONAL FIELDS: Extension: An auto-generated extension number based on the next available sequential number. An extension value can be changed. Example: 1000. Username: Username is auto generated/populated and cannot be changed since it allows the system to use this value for other important operations. Secret: A secret value associated with the UAD is auto-generated in order to allow the UAD to successfully register with the system. The secret value can be changed. PIN: An auto-generated PIN will allow access to voicemail and online self care.

Registering ATA

STEP ONE: Electricity and Ethernet. - Insert a standard RJ-11 telephone cable into the "Phone 1" port. - Connect the other end of the cable to an analog telephone.
- The Sipura SPA 2002 needs electricity, so plug the adapter into its jack and connect it to the electricity network. - Connect the ethernet port to a hub, router or switch as to access LAN.
After successfully connecting the Sipura SPA 2002 to the electricity and data networks, it is time to register it to PBXware. STEP TWO: Sipura SPA 2002 IP address. Find out the IP address of the Sipura SPA 2002 connected to network. 1. Dial ****. 2. Dial 110#. STEP THREE: Sipura SPA 2002 Web Interface. 1. Open a new browser window and enter the IP address in order to access the administration interface.
Example: http://192.168.1.101
an example with IP address 2. Hit "Enter" on your keyboard. STEP FOUR: Configuring the Sipura SPA 2002. 1. Click on "Admin Login" link.
2. Click on "Line 1" link.
3. Enter the following details into their respective fields. REQUIRED FIELDS: Proxy IP address of the PBXware server. Example: 192.168.1.2 User ID PBXware extension number. Example: 1000. Password The Secret of the extension as received in the e-mail associated with this extension. Example: 3dX3r5
an example with details filled in 4. Navigate to the bottom of the page and click on the "Submit All Changes" button. The Sipura SPA 2002 will reboot for changes to take effect.
OPTIONAL FIELDS: Display name Example: John Smith, Reception, Entrance Main, Agent One etc. Auth ID Usually the same number as for the account. Other fields Other "options" or "fields" should be left blank or as is by default, they have no importance for registering your Sipura SPA 2002 to PBXware. - Conclusion: If everything is done as above described, you should have successfully registered your Sipura SPA 2002 to PBXware. Dial *123 to verify registration. - For further information, please contact the manufacturer or check their website www. sipura.com.

Auto Provisioning

UAD Settings Creating Extension Registering ATA LAN And WAN IP Address
STEP ONE: PBXware IP address. 1. Find out the IP address of the PBXware server. STEP TWO: Login to PBXware.
1. Open a new browser window and enter the IP address to access the PBXware administration interface login screen. Example: http://192.168.1.2
STEP THREE: UAD status. 1. Make sure the UAD is enabled. To check the UAD status, navigate to "Settings:UAD" and click on the "edit" icon corresponding to "Sipura SPA 2002".
5. Click on the "Next" button. STEP TWO: Extension values. 1. Enter values into the required field text boxes. REQUIRED FIELDS: Name: Enter a name for the extension being created. Example: John Smith. E-mail: Enter the e-mail address associated with this extension. This e-mail address will receive all system notification messages. Example: john@domain.com Auto provisioning: Set to "Yes". MAC Address: Sipura SPA 2002 MAC address. Example: 001646f5f797
- Your Sipura SPA 2002 needs electricity, so plug the adapter into its jack and connect it to the electricity network. - Connect the ethernet port to a hub, router, or switch as to access LAN.
After successfully connecting the Sipura SPA 2002 to the electricity and data networks, it is time to register it to PBXware. The "Profile Rule" field must be set with TFTP server value. STEP TWO: Sipura SPA 2002 IP address. Find out the IP address of your Sipura SPA 2002 connected to the network. 1. Press the "Menu" button. 2. On the display, scroll to the IP address using the "Up and Down button". 3. Press the "Menu" button. STEP THREE: Sipura SPA 2002 Web Interface.
1. Open a new browser window and enter the IP address in order to access the Sipura SPA 2002 administration interface. Example: http://192.168.1.101
an example with IP address 2. Hit "Enter" on your keyboard. STEP FOUR: Configuring "Profile Rule". 1. Click on the "Admin Login" link.
3. Click on "Provisioning" link.
4. Navigate down to the "Profile Rule" field; it must be set with a TFTP server value. Example: 192.168.1.2/$MA.cfg
an example with details filled in 5. Navigate to the bottom of the page and click on the "Submit All Changes" button. The Sipura SPA 2002 will reboot for changes to take effect.
- Conclusion: If everything is done as above described, you should have successfully registered your Sipura SPA 2002 to PBXware. Dial *123 to verify registration. - For further information, please contact the manufacturer or check their website www. sipura.com.

LAN And WAN IP Address

Make sure your "Auto Provisioning" "LAN" and "WAN" IP fields are set with the correct IP address. 1. Navigate to "Settings:Servers" and click on the "edit" button corresponding to the server.
2. Navigate down to the "Auto Provisioning" group. - LAN IP: Enter your PBXware local (LAN) IP address. Example: 192.168.1.2 - WAN IP: Enter your PBXware wide (WAN) IP address. Example: 89.146.131.130
an example with details filled in 3. Click on the "Save" button. You'll be prompted to click on the "OK" button to restart PBXware for changes to take effect.

Auto Configuration

- Requirements - Auto Configuration

Requriements

1. Make sure your devices are properly connected to the same LAN as your PBXware. 2. Make sure that all devices are set to Factory Defaults. 3. Make sure that all devices are using port 5060.
1. Navigate to "Extensions: Find Phones".
2. A pop-up window will appear. Input range of IP addresses Example: - Start IP: 192.168.1.2 - End IP: 192.168.1.254 3. Click on the "Start" button. PBXware will search for devices connected to the same LAN in the selected range of IP addresses.
an example with a range of IP addresses 4. After PBXware has finished searching for devices, a list of all devices found will be shown. 5. Change the activation status from "Not Activated" to "Auto Configuration" for one or more displayed devices of your choice. 6. Click on the "edit" button next to the activation select box to enter properties for the selected device.
an example with list of found devices 7. After you have edited a device, a pop-up window will appear.
an example with 1 configured line 8. The Sipura SPA 2002 has 4 lines available; you can configure just one or all of them as shown above. Line 1 example Name: John Smith E-mail: john@domain.com Ext: 1000 PIN: 1223 Secret: Enter an at least 6 digit or letter long secret. 9. Click on the "Save" button, the entered values will be saved and the pop-up window will disappear. 10. Click on the "Save" button shown below to finalize "Auto Configuration".
11. Device(s) will automatically reboot and be auto configured.

Glossary

- DHCP = Dynamic Host Configuration Protocol (DHCP) is a communications protocol that lets network administrators manage and automate the assignment of Internet. - HUB = A common connection point for devices in a network. - IP Address = Internet Protocol address. - Local = A local area network (LAN) is a computer network covering a local area, like a home, office or small group of buildings such as a college. - LAN = Local Area Network. - PIN = Personal Identification Number. - Remote = Network devices that are managed or controlled from a network system other than the system to which they are directly connected. - Router = A device that forwards data packets from one local area network (LAN) or wide area network (WAN) to another. - Switch = Network device that selects a path or circuit for sending a unit of data to its next destination. - UAD = User Agent Device. - VoiceMail = The electronic transmission of voice messages over the Internet. The messages are stored on a computer until the recipient accesses and listens to them. - WAN = Wide Area Network. - Web Interface = A web interface is the system of controls with which the user controls a device.