MMC groove for card removal Thumb screw
Insert card face up, this way
Memory card compartment with a 16 MB MMC card installed.
To remove an MMC 1. Open the card compartment door by unscrewing the thumb screw. The screw should only be finger tight. If it was over-tightened, use a thumbnail, a coin or a screwdriver to open the door. 2. Press a finger against the label of the MMC and drag it from the slot. 3. Close the compartment door and fasten the thumb screw finger tight.
To insert a MMC or SD Card 1. Open the card compartment door. 2. Grasp the bottom of the MMC and push the top of the card into the slot. Once the card is started, use your fingernails to slide it the rest of the way to the left, until it is firmly seated in the slot. 3. Close the compartment door and fasten the thumb screw finger tight.

Other Accessories

LMS-522c and LMS-527cDF accessories include MMC cards, MMC card readers and MapCreate 6 mapping software for your computer. MMC card readers are available in USB and parallel port versions. Two switch boxes are available for this unit. The SB-7X transducer switch box switches two transducers to one sonar unit. The SB-8X transducer switch box switches two sonar units to one transducer. If these accessories are not available from your dealer, see the accessory ordering information on the inside back cover of this manual. Visit our web site for a complete listing of all the available accessories. Cleaning Towel A lint-free microfiber towel is included for cleaning the units screen. The towel is highly effective in clearing away water spots, smudges and finger prints. Just wipe the screen with the dry towel it's not necessary to moisten the towel with water. If the screen is badly soiled, you may use water or common window or lens cleaners. DO NOT use polishing compounds or any other abrasive product. If you lose the towel or wear it out, you can replace it with a similar microfiber cloth. These are often available where shop towels or automobile cleaning towels are sold. Caution: Cleaning fabrics other than the microfiber towel type may scratch the screen. Polishing compounds or other abrasive cleaners will scratch the screen. Damage caused by incorrect cleaning is not covered by the warranty. You may wash the towel if it becomes soiled or loses its effectiveness, but do not use fabric softener. Fabric softener will ruin the towels cleaning capability.
MapCreate 6 CD-ROM (left). MMC card reader for USB ports, (right).
Now that you have your unit installed, move on to Section 3, Basic Sonar Operations. There, we'll present a series of step-by-step tutorials to teach you the basics of how to operate your sonar. NOTE: When you first turn the unit on, the Map Page appears. If you'd rather start learning about GPS operation first, turn over to Section 6, Basic GPS Operations.

Area "zoomed"

Normal display, in auto depth range mode (left). Display "zoomed" with Upper and Lower Limits focusing on the portion of the water column from 20 feet to 40 feet deep (right). In the "zoomed" image, note the target definition at lower left, showing a fish holding just above the structure.
To turn off upper and lower limits: From the Sonar Page, press MENU| to AUTO DEPTH RANGE|ENT|EXIT.

FasTrack

This feature automatically converts all echoes to short horizontal lines on the display's far right side. The graph on the rest of the screen continues to operate normally. FasTrack gives you a rapid update of conditions directly under the boat. This makes it useful for ice fishing, or when you are fishing at anchor. When the boat is not moving, fish signals are long, drawn out lines on a normal chart display. FasTrack converts the graph to a vertical bar graph that, with practice, makes a useful addition to fishing at a stationary location.
Surface clutter Fish arches Structure In FasTrack, fish arches show as horizontal bars. Bottom signal Sonar Page showing FasTrack. FasTrack bar graph
Fish I.D. (Fish Symbols & Depths)
The Fish I.D. feature identifies targets that meet certain conditions as fish. The microcomputer analyzes all echoes and eliminates surface clutter, thermoclines, and other signals that are undesirable. In most instances, remaining targets are fish. The Fish I.D. feature displays fish symbols on the screen in place of the actual fish echoes. There are several fish symbol sizes. These are used to designate the relative size between targets. In other words, Fish I.D. displays a small fish symbol when it thinks a target is a small fish, a medium fish symbol on a larger target and so on. The sonar's microcomputer is sophisticated, but it can be fooled. It can't distinguish between fish and other suspended objects such as trotlines, turtles, submerged floats, air bubbles, etc. Individual tree limbs extending outwards from a group of limbs is the hardest object for the Fish I.D. feature to distinguish from fish. You may see fish symbols on the screen when actually, there are no fish. The reverse is also true. The illustrations on the next page show how Fish I.D. can actually miss fish that are present. Does that mean Fish I.D. is broken? No the feature is simply interpreting sonar returns in a specific way to help take some of the work out of reading the screen. Remember: Fish I.D. is one of the many tools we provide so you can analyze your sonar returns for maximum fish finding information. This and other features can help you successfully "see" beneath the boat under varied water and fishing conditions. So, practice with the unit in both the Fish I.D. mode and without to become more familiar with the feature. The default for Fish I.D. is off. 70

Sonar Features menu with Fish I.D. Symbols selected on dualfrequency menu (left); single-frequency menu (right). When the check box to the left is checked, the feature is on. Fig. 1 A Fig. 1 B
Many fish arches visible Fig. 2 A Fish arches above structure
Fewer fish symbols visible Fig. 2 B No fish shown
FasTrack graph confirms fish Figures 1A and 2A show Sonar Page in normal chart mode (left). Figures 1B and 2B (right) show the same underwater scene with Fish I.D. turned on. Note how arches are replaced with symbols.
To turn the Fish I.D. feature on: 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press to FISH SYMBOLS|ENT|EXIT|EXIT. To turn off Fish I.D., repeat the instructions in step 2.

FishTrack

The FishTrack feature shows the depth of a fish symbol when it appears on the display. This lets you accurately gauge the depth of targets. This feature is available only when the Fish I.D. feature is on. The default setting for FishTrack is off. To turn on FishTrack: (Note: These instructions will turn on FishTrack and Fish I.D. at the same time.) 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press |then press to FISH DEPTHS|ENT|EXIT|EXIT. To turn off FishTrack, repeat the instructions in step 1. Turning off FishTrack in this manner will not turn off Fish I.D. symbols.
Symbols with FishTrack depths
Sonar Features menu with Fish I.D. Depths selected on dual-frequency menu (left). When the check box to the left is checked, the feature is on. Sonar Page with Fish I.D. symbols and FishTrack depths turned on (right).
Frequency (Change Transducer Frequency) (LMS-527cDF only)
The LMS-527cDF transducer can operate at both 200 kHz and 50 kHz. The 200 kHz frequency has a 12 cone angle and the 50 kHz frequency has a 35 cone angle. 72
The default frequency is 200 kHz, which is best for use in shallow water (about 300 feet or less). This frequency is the best choice for about 80 percent of the fresh and salt water sport fishing applications. When you get into very deep salt water, 300 to 500 feet or deeper, the 50 kHz frequency is the best choice. The 200 kHz transducer will give you better detail and definition, but less depth penetration. The 50 kHz transducer will give you greater depth penetration, but a little less detail and less definition. (Remember, all sonar units typically read deeper in fresh water than in salt water.) There is a common exception to these rules of thumb. Some fishermen on freshwater lakes (or the ocean) using downriggers like to see them on the sonar. In many of those cases, you'll see a 50 kHz transducer frequency in use because the wider cone angle lets them watch the bait.

You can use the ZIN or ZOUT keys to change the cross track error range. A circular symbol showing your destination (waypoint) appears on the screen as you approach the waypoint, as shown on the screen in the preceding figure. Travel Time is the time that it will take to reach your destination at your present closing speed. (You can also customize the time data box to show Arrival Time instead. Arrival Time is the local time it will be when you arrive at the destination, based upon your present closing speed and track.) In the preceding example, the driver is headed west (a 265 track) toward a waypoint 265 (bearing) away. The cross track error range (white corridor) is 0.20 miles either side of the course. The driver is headed toward trail waypoint 4, which is 0.3 miles away. The vehicle is right on course. Traveling at a speed of 8 mph, the driver will arrive at the waypoint in 2 minutes, 17 seconds. The Navigation Page has its own menu, which is used for some advanced functions and for setting various options. (Options and setup are discussed in Sec. 8). To access the Navigation Page Menu, from the Navigation Page, press MENU. Map Page The Map Page screens show your course and track from a bird's-eye view. By default, this unit shows the map with north always at the top of the screen. (This can be changed. See the topic Map Orientation, in Sec. 8.) If you're navigating to a waypoint, the map also shows your starting location, present position, course line and destination. You, however, don't have to navigate to a waypoint to use the map. Map Page is the default screen that appears when you turn on the unit. To get to the Map Page from another page: Press PAGES| or to MAP|EXIT. When the Map Page is displayed, a screen similar to the following figures appears. The arrow in the center of the screen is your present position. It points in the direction you're traveling. The solid line extending from the back of the arrow is your plot trail, or path you've taken. The map zoom range is the distance across the screen. This number shows in the lower right corner of the screen. In the first of the following example figures, the range is 4,000 miles from the left edge of the map to the right edge of the map. The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its coverage area and the amount of mapping detail shown. There are 39 available map zoom ranges, from 0.02 miles to 4,000 miles. 109
Map Page opening screen (left). Set to 100-mile zoom (center) and 10mile zoom (right). Over Zoomed means you have reached the detail limits in an area covered only by the basic background map. Zooming in closer will reveal no more map detail because a high-detail custom map has not been loaded on the MMC for this area.

Basic GPS Quick Reference
Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. Navigation in too small an area will constantly trigger arrival alarms. 1. Depress the PWR key to turn on the unit. 2. Opening screen displays map of North America at the 4,000 mile zoom range. Rotate through the four main Page screens (Map Page, Satellite Status Page, Navigation Page and Sonar Page) by pressing PAGES| or to select Page Name|EXIT. Switch Pages to display Satellite Status Page. 3. Wait while unit locates satellites and calculates current position. Process is visible on Satellite Page. This takes an average of 1 minute or less under when it is unobstructed by terrain or structures. When the unit acquires position, a tone sounds and a position acquired message appears. 4. With position acquired, press PAGES key to display the Map Page, which gives you a bird's eye view. You can manipulate the map by: Zoom in closer to see greater detail: press ZIN (zoom in key.) Zoom out to see more area, less detail: press ZOUT (zoom out key.) Scroll map north, south, east or west using arrow keys . To stop scrolling and return to current position on map, press EXIT key. 5. Set a waypoint (Wpt 001) at your current position so you can navigate back here: press WPT|WPT. Waypoint symbol and "001" appears. 6. Zoom/scroll map to find a nearby object or location to go to. Use arrow keys to center cursor crosshairss over the map object or location. 7. Navigate to the selected destination: press MENU|ENT|EXIT. Follow dotted course line on Map Page or compass bearing arrow on Navigation Page. 8. At destination, Arrival Alarm goes off; to clear it, press EXIT. Cancel navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. 9. Return to Wpt 1 by Navigate To Waypoint or Backtrack Trail. To Waypoint: press WPT| to SAVED|ENT|ENT|ENT. Use or to select Wpt 001, press ENT|ENT; follow navigation displays. Trail: press MENU|MENU| to MY TRAILS|ENT. Press to Trail 1|ENT|| to NAVIGATE|ENT| to NAVIGATE|ENT| to REVERSE|ENT| to NAVIGATE|ENT. (If arrival alarm sounds, press EXIT.) Follow navigation displays. 10. Back home, Arrival Alarm goes off; press EXIT. Cancel navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. 11. To turn off the unit, press and hold PWR key for three seconds.

After the unit has acquired a position: 1. Press WPT| to POI-RESTAURANTS. 2. You could search the entire restaurant category, but in this example we will narrow our search. Press to SUBCATEGORY column| to FAST FOOD CHAINS|ENT| to NEAREST|ENT. 3. The unit says it is calculating, then a list of restaurants appears, with the closest highlighted at the top of the list. The restaurant farthest from you is at the bottom of the list.
Find Waypoint Menu (left). Category Selection menu (center). List of the nearest restaurants (right).
4. You could scroll through the list to select another restaurant, but for now we will just accept the nearest one. Press ENT.
The POI Information screen shows name, street address, phone number, latitude/longitude, distance to restaurant and its compass bearing. In the first figure (left) Go to Waypoint is selected. In the second figure (right) Find on Map is highlighted.
5. The POI information screen appears. If you wanted to navigate there, you could press Enter, since the Go To Waypoint command is highlighted. We just want to see it on the map, so press to FIND ON MAP|ENT. 120
6. The unit's map appears, with the cursor crosshairss highlighting the restaurant's POI symbol. A pop-up data box shows the POI's name, distance and bearing. A data box at the bottom of the screen continues to display the location's latitude and longitude.
Map screen showing Finding Waypoint, the result of a restaurant search.
7. To clear the search and return to the last page displayed, press EXIT repeatedly. (Before you completely exited out of the Search menus, you could have gone looking for another place.) NOTE: Search works from mapping and POI data loaded in the unit. If you do not have a high-detailed custom map (containing POI data) for the area you are searching loaded on the MMC, you may not find anything.

Set a Waypoint

A waypoint is simply an electronic address, based on the latitude and longitude of a position on the earth. A waypoint represents a location or destination that can be stored in memory, then recalled later for navigational use. You can create a waypoint at the cursor position on the map or at your current position while you are navigating. A waypoint may be created at any location by manually entering the position's latitude and longitude. You can copy waypoints from your unit to your personal computer with MapCreate software. When you want to repeat a trip, these archived waypoints can be reloaded into your GPS unit. To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint. 121

Create Waypoint at Current Position While you are traveling, press WPT|WPT. The waypoint is saved and
automatically given a name with a sequential number, such as "waypoint 003." The waypoint symbol and number appear on the map.

Step 1. Step 2.

Step 3.

Step 4.

Sequence for setting a waypoint. Step 1: while traveling, press WPT twice to call up the Find Waypoint screen (seen in Step 2) and set a waypoint. Step 3: a message says the waypoint has been saved. Step 4: vehicle continues on its way; waypoint number and symbol are visible on map.
NOTE: The Quick Save method uses the default waypoint symbol until you edit an existing waypoint and change its symbol. After a waypoint symbol is changed, the unit will remember the one you chose and use it the next time you save a waypoint. To go back to the default symbol, edit a waypoint and choose the original symbol, or use the Reset Options command. 122

Create Waypoint on Map

1. Use the arrow keys to move the cursor crosshairs to the place where you want to make a waypoint. 2. Press WPT|WPT. The waypoint is saved and automatically given a name with a sequential number, like "waypoint 001." The waypoint symbol and number appear on the map.

Navigate To a Waypoint

You can select any waypoint visible on the Map Page with the cursor, then use the Navigate to Cursor command (we'll describe how later in this section.) However, you can avoid scrolling the map to pick your waypoint if you use the Find Waypoint commands: 1. Press WPT| to SAVED|ENT. To look up the nearest waypoint, press to NEAREST|ENT; or, to look by name (and scroll through the entire waypoint list), press ENT. For this example, let's look by name. 2. If your waypoint list is a long one, you can spell out the waypoint name in the FIND BY NAME box to search for it. (Press or to change the first character, then press to move the cursor to the next character and repeat until the name is correct, then press ENT to jump to the list below.) 3. If the list is short, you can jump directly to the FIND IN LIST box by pressing ENT. Use or to select the waypoint name, press ENT and the waypoint information screen appears with the GO TO command selected. 4. To begin navigating to the waypoint, press ENT.

On the Map Page, the trail you are navigating is represented by a dotted line that alternates with a flashing solid line. The Navigation Page will also show the navigated trail as a dotted line. The bearing arrow on the compass rose points to the next waypoint on the trail. As you travel, the arrival alarm will go off when you near a trail waypoint, and the bearing arrow on the compass rose will swing around and point to the next trail waypoint. Press EXIT to clear the alarm. 130
North Present position arrow

Trail point

Trail dotted line
Navigate trail, map views: Driver is northbound heading straight toward trail point 6 (left). Northbound driver has reached point 6 and has turned west to follow trail (right). Track or compass heading indicator Trail waypoint symbol Course line made from trail Cross track error range (off course indicator)

Bearing arrow

Arrival alarm
Navigate trail, navigation page (compass rose) views: driver is northbound heading straight toward trail point 6 (left); bearing arrow shows the trail point is due north (straight ahead.) Driver has reached trail point 6 and must turn west to follow the trail (right). Arrival alarm goes off and bearing arrow swings around toward the west and the next waypoint. The unit now shows navigation information to point 7, which is 2.02 miles away.
Navigate a Back Trail (backtrack) 1. Press MENU|MENU| to MY TRAILS|ENT. 2. Press | to enter the Saved Trail list, then use or to select the desired Trail Name|ENT. 3. Press to DELETE TRAIL| to NAVIGATE|ENT. 4. Press to NAVIGATE| to REVERSE|ENT| to NAVIGATE|ENT. The unit begins showing navigation information along the trail, in reverse.
NOTE If you are already located at or near the end of your trail, the arrival alarm will go off as soon as you hit ENT. Press EXIT to clear the alarm and proceed. 5. Now, begin navigating with your unit. 6. When you reach your destination, be sure to cancel your navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT. The unit asks if you're sure; press |ENT.
Transfer Custom Maps and GPS Data Files
Custom Maps: Custom maps work only from the MMC card or SD card. When a card containing a Custom Map File is loaded into the unit, the unit automatically loads the map into memory when the unit is turned on. Instructions for copying Custom Map Files to an MMC are contained in the instruction manual for your MMC card reader and MapCreate 6 software. For instructions on inserting an MMC into the unit, see Sec. 2, Installation/Accessories. GPS Data files: GPS Data Files contain waypoints, routes, trails and event marker icons. Instructions for copying GPS Data Files between your computer and an MMC are contained in the instruction manual for your MMC card reader and MapCreate 6 software. GPS data automatically recorded in the unit's internal memory must be saved to the MMC (as a GPS Data File) in order to store it on your personal computer. GPS Data Files stored on an MMC must be copied from the card to the unit's internal memory before the unit can read them. Here's how: 1. Insert the MMC into your unit. Press MENU|MENU| to SYSTEM SETUP|ENT| to TRANSFER MY DATA|ENT and the screen below appears. 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the unit in order to activate the Load or Save commands. To transfer data from the unit to the MMC: press ENT (for SAVE.) To transfer data from the MMC to the unit: press to LOAD|ENT. 132

Find Distance from Point to Point
You can also measure distance between two other points on the map. 1. While on the Map Page press: MENU| to FIND DISTANCE|ENT. 2. Center your cursor over the first position. (A rubber band line appears, connecting your current position to the cursor's location.) Press ENT to set the first point, and the rubber band line disappears. 3. Move the cursor to the second position. The rubber band line reappears, connecting the first point you set to the cursor. The distance along that line will appear in the pop-up box. 4. Press EXIT to clear the command and return to the page screen. (Press EXIT once more to clear the cursor.)
Icons are graphic symbols used to mark some location, personal point of interest or event. They can be placed on the map screen, saved and recalled later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols you can pick from when creating an icon. Icons are similar to waypoints, but they do not store as much information (like names) as waypoints do. You can't use a menu to navigate to icons as you can with waypoints. (But, you can use the map cursor and navigate to any icon on the map.) You can create an icon at the cursor position on the map, or at your current position while you are navigating. Create Icon on Map 1. Use the arrow keys to move the cursor to the place where you want to make an icon. 2. Press ENT and the Select Icon Symbol menu will appear. 3. Press , to select your icon symbol and press ENT. The icon appears on the map.
Cursor selects icon location (left). Select Icon Symbol menu (center), Music note icon on map (right). (Cursor has been moved for clarity.)
Create Icon at Current Position 1. While you are traveling, press ENT and the Select Icon Symbol menu will appear. 2. Press , to select your icon symbol, then press ENT. The icon appears on the map. Delete an Icon You can delete all the icons at one time, delete all icons represented by a particular symbol or use the cursor to delete a selected icon from the map. 136
1. Press MENU| to DELETE MY ICONS|ENT. 2. Press to DELETE ALL ICONS, DELETE BY SYMBOL, or DELETE FROM MAP and press ENT.

Delete icons menu.

The Delete All Icons command will ask if you are sure. Press to YES|ENT. All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu. Press or or or to select the icon symbol to delete, then press ENT. A message appears saying all icons with the selected symbol have been deleted. The Delete From Map command will prompt you to move the cursor over an icon to select it. After selecting the icon, press ENT and it disappears from the map. Navigate to an Icon Use the cursor to select the desired icon on the map, then use the Navigate to Cursor command. 1. Use arrow keys to center cursor crosshairss over the icon. 2. To navigate to the selected icon location: press MENU|ENT|EXIT. Follow course line on the Map Page or the compass bearing arrow on the Navigation Page.

Navigate a Route 1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE, press MENU|MENU| to ROUTE PLANNING|ENT.
Route Planning on Main Menu (left). Routes menu (center). Edit Route menu (right). Navigate is selected on Edit Route menu.
2. Press to select route name|ENT| to NAVIGATE|ENT. 3. Upon arrival at your destination, cancel navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. The following figures show what the Navigation Page and Map Page look like while navigating a route. Navigate a Route in Reverse Here's how you run a route backward, from the end waypoint to the beginning waypoint: 1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE, press MENU|MENU| to ROUTE PLANNING|ENT. 2. Press to select route name|ENT| to NAVIGATE| to REVERSE|ENT| to NAVIGATE|ENT. 3. Upon arrival at your destination, cancel navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT.
Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the east. In Fig. 3 the traveler has turned east on his new course and is heading straight for Wpt 2, which is 2.37 miles away. Fig. 4 shows route navigation on the Map Page. In this figure, the traveler has reached Wpt 2 and is half-way along the leg between Wpts 2 and 3.

Trails

Delete a Trail This is the command used to delete a trail: Press MENU|MENU| to MY TRAILS|ENT| to trail name|ENT| to DELETE TRAIL|ENT| to YES|ENT.
You can also delete all trails at once: 1. Press MENU|MENU| to MY TRAILS|ENT. 2. Press to DELETE ALL|ENT| to YES|ENT.
Edit a Trail Name To edit a trail name: press MENU|MENU| to MY TRAILS|ENT| to trail name|ENT|ENT. Press or to change the first character, then press to the next character and repeat until the name is correct. Press ENT then EXIT repeatedly to return to the previous page display.
You can quickly call up the Edit Trail menu by selecting a trail on the map with the cursor. Simply move the cursor over a trail and a pop-up box appears. Press WPT and the Edit Trail menu opens.
Trail selected with map cursor (left). The pop-up box shows distance and bearing from current position to the selected point on the trail. The Edit Trail menu (right).
Edit a Trail Color To edit a trail color: press MENU|MENU| to MY TRAILS|ENT| to trail name|ENT| to COLOR|ENT. Press or to select a color style, then press ENT. Press EXIT repeatedly to return to the previous page display. Edit a Trail Pattern To edit a trail pattern: press MENU|MENU| to MY TRAILS|ENT| to trail name|ENT| to PATTERN|ENT. Press or to change the first character, then press to the next character and repeat until the pattern is correct. Press ENT, then EXIT repeatedly to return to the previous page display.

Pop-up Help command highlighted on System Setup menu (left). Popup Help message for Sounds (right).
The Reset Options command allows you to switch unit features and functions back to factory default settings. 1. Press MENU|MENU| to SYSTEM SETUP|ENT| to RESET OPTIONS|ENT| to YES|ENT. NOTE: Reset Options does not erase any waypoints, routes, icons, plot trails or sonar logs.
Reset Options highlighted on the System Setup menu (left). Reset Options confirmation message (right).
Screen Contrast and Brightness
To adjust Contrast: 1. Press MENU|MENU|ENT. 2. Highlight CONTRAST, then use to move the contrast adjustment bar. The left end of the scale is the lowest contrast level. The right end is the highest contrast level.
The Screen Menu with Contrast bar selected.
To adjust the display's brightness: 1. Press MENU|MENU|ENT. 2. Press to BRIGHTNESS. Press to move Brightness Control bar. The left end of the scale is the lowest brightness level. The right end of the scale is the highest brightness level.

Display Mode menu.

To adjust the screen's display mode: 1. Press MENU|MENU|ENT. 2. Press to DISPLAY MODE|ENT, which will open the Display Mode menu with three options: Normal, High Contrast and Night Viewing. 3. Select the desired mode and press ENT. Press EXIT|EXIT to return to the map display.

Set Language

This unit's menus are available in 10 languages: English, French, German, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU|MENU| to SYSTEM SETUP|ENT. 2. Highlight SET LANGUAGE|ENT. 3. Use to select the desired language and press ENT. All menus now will appear in the language you selected.

Set Local Time

Using the local time setting is useful when estimating local arrival time while navigating. 1. Make sure your unit has acquired your position, then press MENU|MENU, highlight SYSTEM SETUP and ENT. 2. Highlight SET LOCAL TIME and press ENT. 3. Local time will be highlighted, so press ENT. Use to change the first character, then press to move the cursor to the next character. Repeat those steps until the time has been set. Press ENT. To set the Month: 1. Make sure your unit has acquired your position, then press MENU|MENU, highlight SYSTEM SETUP and ENT. 2. Highlight SET LOCAL TIME and press ENT. 3. Select MONTH and ENT. Use to select the desired month and press ENT. To set the Day:

Find by Nearest option, left, Calculating screen, center, POI list, right.
3. To search by the name of a POI: press ENT. There are two options: A. You can spell out the POI in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, then press ENT|ENT. B. Jump down to the lower selection list by pressing ENT, then press or to select a POI from the list, then press ENT to call up the POI's Waypoint Information screen.
Find by Name option, left, Find by Name menu, right.
4. When the POI's Waypoint Information screen is displayed, you can choose to Go To the POI waypoint by pressing ENT or find it on the map by pressing|ENT.
Go To Waypoint highlighted (left). Find on Map selected (right).
Find Streets or Intersections
Find a Street 1. From the Map Page, press MENU| to FIND STREETS|ENT and the Find Streets Menu appears. 2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, then press ENT|ENT. B. Or you can jump down to the lower box and pick a street from the list. Press ENT, then press or to select a street from the list and press ENT.
Find Streets menu (left). When finding a street by name (right), spell out the name in the top box or select it from the list in the lower box.
3. The Find Streets menu reappears with the street you're searching for in the First Street box. (In this example, it's 80th Street.) To search 196
for that street, press to FIND FIRST STREET|ENT. A message appears asking you to wait while the unit finds the street. When the Streets Found list appears, press or to select the street you are searching for and press ENT.
Find Streets menu with the Find First street highlighted (left). Streets Found list (right).
4. The Map Page appears, with the cursor pointing to the found street. If you want to navigate to the found street at the cursor location, just press MENU|ENT|EXIT.
Map Page showing results of a street search. The cursor points to the located street.

Old Hawaiian Mean for Hawaii, Kauai, Maui, Oahu Old Hawaiian Hawaii Old Hawaiian Kauai Old Hawaiian Maui Old Hawaiian Oahu Oman Oman Ordinance Survey Great Britain 1936 Mean for England, Isle of Man, Scotland, Shetland Islands, Wales Ordinance Survey Great Britain 1936 England Ordinance Survey Great Britain 1936 England, Isle of Man, Wales Ordinance Survey Great Britain 1936 Scotland, Shetland Islands Ordinance Survey Great Britain 1936 Wales Pico de las Nieves Canary Islands Pitcairn Astro 1967 Pitcairn Island
Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic System 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad & Tobago, and Venezuela South American 1969 Argentina South American 1969 Bolivia South American 1969 Brazil South American 1969 Chile South American 1969 Colombia South American 1969 Ecuador South American 1969 Ecuador (Baltra, Galapagos) South American 1969 Guyana South American 1969 Paraguay South American 1969 Peru South American 1969 Trinidad & Tobago South American 1969 Venezuela South Asia Singapore Tananarive Observatory 1925; Madagascar Timbalai 1948 Brunei, East Malaysia (Sabah, Sarawak)
Tokyo Mean for Japan, Korea, Okinawa Tokyo Japan Tokyo Korea Tokyo Okinawa Tristan Astro 1968 Tristan da Cunha Viti Levu 1916 Fiji (Viti Levu Island) Wake Eniwetok 1960 Marshall Islands Wake Island Astro 1952 Wake Atoll WGS 1972 Global Definition Yacare Uruguay Zanderij Suriname

FCC Compliance

This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the factory customer service department for help.