SyncMaster 206BW / 226BW

Install drivers

Notation

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock
When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.
Do not use a damaged or loose plug. This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet. This may cause fire.
Do not disconnect the power cord while using the monitor. A surge may be caused by the separation and may damage the monitor.
Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth. Using the power cord with a dusty plug or connector may cause an electric shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor.
Place your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it.
Do not place the product on an unstable or small surface area. Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the product on the floor. Take care, as someone, specifically children may trip over it.
Keep any flammable objects such as candles, insecticides or cigarettes away from the product. Otherwise, this may cause fire.
Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire.
Put down the monitor carefully. Failing to do so may damage the monitor.
Do not place the monitor face down. This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of children's reach. The plastic packaging (bag) may cause suffocation if children play with it.

Cleaning and Use

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire.

This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 20 inch Wide (51 cm) - 1680 x inch Wide (56 cm) - 1680 x 1050
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.
Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of children's reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.

Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast. >> Click here to see an animation clip Brightness button [ ] Adjust buttons [ Enter button [ ] / SOURCE button ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Adjust items in the menu. Activates a highlighted menu item. / Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. Use this button for auto adjustment. >> Click here to see an animation clip Use this button for turning the monitor on and off. This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.
AUTO button Power button [ ] Power indicator
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
The configuration at the back of the monitor may vary from product to product. POWER port DVI IN (HDCP) port RGB IN port Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI port on the back of your monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. For using a locking device, contact where you purchase it.
See Connecting Cables for further information regarding cable connections.

Connecting Cables

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. - Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN] Using the DVI (Digital) connector on the video card. - Connect the DVI Cable to the DVI Port on the back of your Monitor. [DVI IN (HDCP)] Connected to a Macintosh. -Connect the monitor to the Macintosh computer using the D-sub connection cable. If the monitor and the computer are connected, you can turn them on and use them.

Using the Stand

Monitor Assembly

Monitor and Bottom

Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.

A. Monitor B. Mounting interface pad (Sold separately)
Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove three screws and then remove the stand from the LCD monitor. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

Monitor Driver

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Installing the Monitor Driver (Automatic) Insert the CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button (Microsoft Windows XP/2000 Operating System).
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/
Monitor driver installation is completed.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
Microsoft Windows XP Operating System Insert the CD into the CD-ROM drive. Click "Start" "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced."
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver." and select "Install from a list or." then click "Next" button.
Select "Don't search ,I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button.
Click the "Close" button then click the "OK" button continually.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button.
How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click the "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.
Microsoft Windows Millennium Operating System Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver." Choose "Display a list of all the driver in a specific location." then click the "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click the "OK" button.

Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft Windows NT Operating System Click "Start," "Settings," "Control Panel," and then double-click the "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) "Enter" the model name of your monitor. This information will not affect the actual execution of XWindow. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.

Control Buttons

[MENU / ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu.
[ ] Press this button to activate a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.

Information

Description Shows a video source, display mode on the OSD screen.

MENU ,

Check List
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Symptom No images on the screen. I cannot turn on the monitor.
Check List Is the power cord connected properly? Can you see "Check Signal Cable" on the screen?
Solutions Check the power cord connection and supply.
(Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an error message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press SOURCE button to have the monitor double-check the input signal source.
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Can you see "Not Optimum Mode", "Recommended Mode 1680 X Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 X Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 X Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.)
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Connected using the DVI cable?
You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system. Unlock the OSD by pressing the [MENU / button for at least 5 seconds. ]

I cannot see the On Screen Display.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
The screen shows strange colors or just black and white.
Check the signal cable connection. Make sure the video card is fully inserted in it's slot.

Reboot the computer.

Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel Display Settings. Has the video card been set properly? There is a message that reads "Unrecognized Have you installed the monitor driver? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions.
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Have the Windows colors been set properly?
monitor, Plug & Play (VESA DDC) monitor found".
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.

Install the monitor driver according to the Driver Installation Instructions.
Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer.) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution.) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Q&A

Question How can I change the frequency? Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP : Set the resolution in the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution in the Control Panel Settings.

Display

Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP : Set the resolution in the Control Panel Appearance and Themes Display Screen Saver. Set the function in the BIOS-SETUP of the computer. Windows ME/2000 : Set the resolution in the Control Panel Display Screen Saver. Set the function in the BIOS-SETUP of the computer. Refer to the Windows/Computer Manual How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.

Self-Test

Self-Test Feature Check | Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.

15pin to 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable, (Option) Dimensions (W x H x D) / Weight 476.0 X 329.0 X 65.2 mm / 18.7 x 12.9 x 2.5 inch (Without Stand) 476.0 X 396.4X 219.3 mm / 18.7 x 15.6 x 8.6 inch (With Stand) / 5.3 kg / 11.6 lbs VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 F ~113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing

Storage

Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problelms. For example, the number of TFT LCD sub pixels contained in this product are 5,292,000. Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

Normal Operation

Power saving mode
Power off (Power button) EPA/ENERGY 2000 Black Less than 1 W
Power Indicator Power Consumption

Blue Less than 55 W

Blue, Blinking Less than 2 W (Off-mode)
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Preset Timing Modes Horizontal Frequency (kHz) 31,469 31,469 31,469 35,000 49,726 68,681 37,500 37,861 35,156 37,879 46,875 48,077 48,363 56,476 60,023 67,500 60,000 79,976 65,290 Vertical Frequency (Hz) 70,086 59,940 70,087 66,667 74,551 75,062 75,000 72,809 56,250 60,317 75,000 72,188 60,004 70,069 75,029 75,000 60,000 75,025 59,954

Display Mode

Pixel Clock (MHz) 25,175 25,175 28,322 30,240 57,284 100,000 31,500 31,500 36,000 40,000 49,500 50,000 65,000 75,000 78,750 108,000 108,000 135,000 146,250
Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/-/-,+/+ +/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+ -/+
IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA,1280 x 960 VESA,1280 x 1024 VESA, 1680 X 1050
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number
of the Horizontal Cycle is called the Horizontal Frequency. Unit : kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit : Hz

SyncMaster 226BW

General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7M Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI Compliant Digital RGB, 0.7 Vp-p 5%, TTL level (V high 2.0V, V low Maximum Pixel Clock 146 MHz (Analog,Digital) Power Supply AC 100 - 240V~ (+/- 10%) Signal Cable 50/60Hz 3Hz 1680 X 1050@60 Hz 1680 X 1050@60 Hz 30 ~ 81 kHz 56 ~ 75 Hz 22 " Wide Diagonal (56 cm) 473.8 mm (H) x 296.1 mm (V) 0.258 mm (H) x 0.258 mm (V) SyncMaster 226BW
15pin to 15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Option) Dimensions (W x H x D) / Weight 514.6 X 353.3 X 63.0 mm / 20.2 x 13.9 x 2.4 inch (Without Stand) 514.6 X 422.0 X 219.3 mm / 20.2 x 16.6 x 8.6 inch (With Stand) / 4.9 kg / 10.8 lbs VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50 F ~ 104 F (10 C ~ 40 C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 F ~113 F (-20 C ~ 45 C) Humidity : 5 % ~ 95 %, non-condensing

Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA Europe 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 1-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com/co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx
BELGIUM CZECH REPUBLIC DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN U.K CIS RUSSIA UKRAINE Asia Pacific AUSTRALIA CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN
( 0,15/min) 01805 - 121213 ( 0,12/Min) 88 ( 0.10/Min) SAMSUNG (7267864)
http://www.samsung.com/be http://www.samsung.com/cz http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/uk
8-800-200-0400 8-800-502-0000
http://www.samsung.ru http://www.samsung.com/ur
603 800-810-5858, 010- 3030 8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 02-689-3232 0800-329-999
http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw

906BW 206BW 226BW

Widescreen Analog/Digital LCD Monitors
19", 20" and 22" widescreens 16:10 aspect ratio High native resolutions Piano black bezel MagicSpeed ultra-fast 2 ms (G to G) response time 160/160 horizontal/vertical viewing angles Exclusive Magic technologies
imagine having elbow room on screen. Thats exactly what you get with the Samsung BW series of widescreen LCD monitors. Wide 16:10 aspect ratios let you multitask, with room for more than one application at a time. The extra room also makes working with graphics programs and multiple tool palletes easier. An ultra-fast 2 ms (G to G) response time is perfect for motion graphics editing. And exclusive MagicBright 3, MagicColor and MagicTune technologies give you complete control over outstanding color. All the color. All the room. With the Samsung BW series, its not hard to imagine.
Features Widescreen Format Whether youre creating a masterpiece or just watching one on DVD, the wide 16:10 aspect ratio and 1680 x 1050 resolution deliver a better view. MagicSpeed 5 ms Response Time Fast pixel response means fast action with virtually no blurring or ghosting. MagicColor and MagicBright 3 Enjoy rich, natural color and easily selectable brightness modes that include Text, Internet, Game, Sports, Movie and Print view. MagicTune with Asset Management Monitor adjustments are made via the mouse, for a cleaner, sleeker monitor with fewer buttons. Wall-Mountable Whether its on your desk or hanging on your wall, theyll make you look good.

Specifications

Panel Type Viewable Size Pixel Pitch Brightness (typical) Contrast Ratio (typical) Response Time (typical) Viewing Angles (H/V) Native Resolution Aspect Ratio Maximum Color Interface Input Video Signal Sync Type Input connetcors Plug and Play Power Consumption Stand Type Cabinet Color VESA Wall Mount Magic Technologies
a-si TFT/TN 19.0" Wide 0.285mm 300 cd/m2 3000:1 DC 2 ms (G to G) 160/x 900 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite H/V, SOG 15-pin D-sub, DVI-D DDC 2B 42 watts (max.), <1 watt (DMPS mode) Simple Piano black 75 mm MagicTune with asset management, MagicSpeed, MagicColor , MagicBright 3
a-si TFT/TN 20.0" Wide 0.258mm 300 cd/m2 3000:1 DC 2 ms (G to G) 160/x 1050 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite, SOG 15-pin D-sub, DVI-D DDC 2B 55 Watt (max.), <2 watt (DMPS mode) Simple Piano black 75 mm MagicTune with asset management, MagicSpeed, MagicBright 3
a-si TFT/TN 22.0" Wide 0.282mm 300 cd/m2 3000:1 DC 2 ms (G to G) 160/x 1050 16:10 16.7M Analog/Digital Analog RGB, TMDS Digital Link, DVI Separate H/V, Composite, SOG 15-pin D-sub, DVI-D DDC 2B 55 Watt (max.), <2 watt (DMPS mode) Simple Piano black 100 mm MagicTune with asset management, MagicSpeed, Magic Contrast, MagicBright 3 DVI (HDCP), Swivel and tilt 20.3" x 16.6" x 8.6" (without stand: 20.3" x 2.5" x 13.9") 10.8 lbs. 3/3
Special Features Dimensions (W x H x D) Net Weight Warranty (P/L)
Ergonomic adjustable: tilt 17.6" x 14.3" x 7.9" 9.3 lbs. 3/3
DVI (HDCP), Swivel and tilt 18.7" x 15.6" x 8.6" (without stand: 18.7" x 2.6" x 12.9") 11.7 lbs. 3/3

226BW Dimensions

20.3"

16.6"

Product Information: 1-866-542-7214 Product Support: 1-800-SAMSUNG

www.samsung.com/monitor

2006 Samsung Electronics America, Inc. Samsung is a registered mark of Samsung Electronics Corp., Ltd. Specifications and design are subject to change without notice. See www.samsung.com for detailed information. Printed in USA. 226BW12/06R1