DJ MIXER

DN-X300
OPERATING INSTRUCTIONS INSTRUCCIONES DE OPERACION

FOR ENGLISH READERS

5 ~ PAGE

PARA LECTORES DE ESPAOL

PAGINA 11

~ PAGINA 16

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

SAFETY INSTRUCTIONS

1. 2. 3. Read Instructions All the safety and operating instructions should be read before the product is operated. Retain Instructions The safety and operating instructions should be retained for future reference. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. Follow Instructions All operating and use instructions should be followed. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 15. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 16. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance this indicates a need for service. 22. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PESONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

4. 5. 6. 7.

WARNING: TO
PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

LABELS:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
2. Do not open the top cover
In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON dealer.

ATTENTION

POUR VITER LES CHOCS LECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND.
10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

3. Do not place anything inside
Do not place metal objects or spill liquid inside the DJ mixer. Electric shock or malfunction may result. Please, record and retain the Model name and serial number of your set shown on the rating label. Model No. DN-X300 Serial No.
FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT
GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE

ENGLISH

ESPAOL
TOP PANEL DIAGRAM / DIAGRAMA DEL PANEL SUPERIOR
t yu i o !0!0 o i !1 y t r e w q !7 !9 !2 !3 !4 !5 !6 !7 !8 !9 @0 @1 @1 @2
REAR PANEL DIAGRAM / DIAGRAMA DEL PANEL POSTERIOR
#7 #6 #5 #4 #3 #2 #1 #0 #3 #2 #1 #0
FRONT PANEL DIAGRAM / DIAGRAMA DEL PANEL FRONTAL
NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A LUTILISATION / NOTE SULLUSO NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA
DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive. BEREINSTIMMUNGSERKLRUNG Wir erklren unter unserer Verantwortung, da dieses Produkt, auf das sich diese Erklrung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 73/23/EEC, 89/336/EEC und 93/68/EEC. DECLARATION DE CONFORMITE Nous dclarons sous notre seule responsabilit que lappareil, auquel se rfre cette dclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. Daprs les dispositions de la Directive 73/23/EEC, 89/336/EEC et 93/68/EEC. DICHIARAZIONE DI CONFORMIT Dichiariamo con piena responsabilit che questo prodotto, al quale la nostra dichiarazione si riferisce, conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. In conformit con le condizioni delle direttive 73/23/EEC, 89/336/EEC e 93/68/EEC. QUESTO PRODOTTO E CONFORME AL D.M. 28/08/95 N. 548

Unplug the power cord when not using the set for long periods of time. Wenn das Gert eine lngere Zeit nicht verwendet werden soll, trennen Sie das Netzkabel vom Netzstecker. Dbrancher le cordon dalimentation lorsque lappareil nest pas utilis pendant de longues priodes. Disinnestate il filo di alimentazione quando avete lintenzione di non usare il filo di alimentazione per un lungo periodo di tempo. Desconecte el cordn de energa cuando no utilice el equipo por mucho tiempo. Neem altijd het netsnoer uit het stopkontakt wanneer het apparaat gedurende een lange periode niet wordt gebruikt. Koppla ur ntkabeln om apparaten inte kommer att anvndas i lng tid.
Do not let insecticides, benzene, and thinner come in contact with the set. Lassen Sie das Gert nicht mit Insektiziden, Benzin oder Verdnnungsmitteln in Berhrung kommen. Ne pas mettre en contact des insecticides, du benzne et un diluant avec lappareil. Assicuratevvi che lunit non venga in contatto con insetticidi, benzolo o solventi. No permita el contacto de insecticidas, gasolina y diluyentes con el equipo. Laat geen insektenverdelgende middelen, benzine of verfverdunner met dit apparaat in kontakt komen. Se till att inte insektsmedel p spraybruk, bensen och thinner kommer i kontakt med apparatens hlje.
FCC INFORMATION (For US customers)

1. PRODUCT

Never disassemble or modify the set in any way. Versuchen Sie niemals das Gert auseinander zu nehmen oder auf jegliche Art zu verndern. Ne jamais dmonter ou modifier lappareil dune manire ou dune autre. Non smontate mai, n modificate lunit in nessun modo. Nunca desarme o modifique el equipo de ninguna manera. Nooit dit apparaat demonteren of op andere wijze modifiren. Ta inte isr apparaten och frsk inte bygga om den.

3. NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the product into an outlet on a circuit different from that to which the receiver is connected. Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.
(For sets with ventilation holes) Do not obstruct the ventilation holes. Die Belftungsffnungen drfen nicht verdeckt werden. Ne pas obstruer les trous daration. Non coprite i fori di ventilazione. No obstruya los orificios de ventilacin. De ventilatieopeningen mogen niet worden beblokkeerd. Tpp inte till ventilationsppningarna.

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
CAUTION The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. No naked flame sources, such as lighted candles, should be placed on the apparatus.
Please be care the environmental aspects of battery disposal. The apparatus shall not be exposed to dripping or splashing for use. No objects filled with liquids, such as vases, shall be placed on the apparatus.

2 INTRODUCTION

Thank you very much for purchasing the DENON DN-X300 DJ MIXER. DENON proudly presents this advanced DJ MIXER to audiophiles and music lovers as a further proof of DENONs non-compromising pursuit of the ultimate in sound quality. The high quality performance and easy operation are certain to provide you with many hours of outstanding listening pleasure.
2 PART NAMES AND FUNCTIONS

(1) Top panel

(Refer to page 3.)
q MIC ON/OFF/TALKOVER switch
When TALKOVER is selected , all signals except the microphone level are decreased by 20 dB. When at the ON or OFF position all signals remain at their standard levels.
!0 EFFECT LOOP ON/OFF switch
Routes the assigned signal through the external processor attached to the SEND/RETURN connectors on the rear. When the EFFECT LOOP is ON, the LED is lit. (When the external processor isnt connected, the LED will blink.)

TABLE OF CONTENTS

MAIN FEATURES..5 PART NAMES AND FUNCTIONS.5, 6 CONNECTIONS..7
SPECIFICATIONS..8 FADER START..9 ROTATING INPUT SELECT SWITCHES.10

w MIC EQ controls

Contour the frequency response of the MIC input 12 dB to +12 dB. At the center position, sound is flat.

!1 CH REVERSE button

This switch allows the left hand fader or right hand fader to control PGM1 or PGM2. When the CH REVERSE mode is ON, the CH1 fader will be able to control PGM 2 sound and the CH2 fader will be able to control PGM 1 sound. NOTE: Please dont confuse with the CH 1/2 FADER REVERSE switch $4.

2 ACCESSORIES

Please check to make sure the following items are included with the main unit in the carton:

e MIC LEVEL control

q Operating instructions..1 w AC adaptor...1 (AA-26 : for AC 120 V, AA-27 : for AC 230 V) Adjusts the level of Mic signal.

r AUX INPUT control

Adjusts the level of AUX input. This input is mixed after the Crossfader and EFFECT LOOP.

1 MAIN FEATURES

01. Penny & Giles Crossfader Smooth and reliable mixing is excelled by Penny & Giles Crossfader. 02. VCA controlled Channel Fader and Crossfader 03. Channel Fader and Crossfader curve adjustable This feature allows adjusting the shape of the Crossfader and Channel fader response from a gentle curve for smooth to the steep pitch required for top performance cut and scratch effects. 04. Channel Fader and Crossfader Reverse 05. Channel Fader and Crossfader Start The CD player can be started or stopped simply by increasing or decreasing the level of the Ch. fader or by using the Crossfader left to right or right to left. (This function can only be used when the DENON CD players DN-S3000, DN-S5000, DNS1000 or etc. is connected to the DN-X300.) 06. Channel Reverse function This function allows the left hand channel fader or right hand channel fader to control PGM1 or PGM2. 07. Enhanced Input/Output terminals 4 LINE, 2 PHONO, 1 AUX, 1 Microphone systems, 2 MASTER outputs and 1 BOOTH output are provided independently. Effect SEND/RETURN terminals are also provided for a external effects processor. 08. 3-Band equalizer/gain LOW, MID, HI and GAIN controls are available on every input channel. 09. 3-Band Equalizer Kill function 10. 8 direction placement for input selector 11. Microphone Talkover function

t Source EQ controls

Contour the frequency response of the selected inputs. HI and MID: Adjusts the high-tone and mid-tone sound 40 dB to +10 dB. LOW: Adjusts the low-tone sound 40 dB to +6 dB. NOTE: Clipping may occur if adjustments are set to harsh.

!2 MASTER LEVEL control

Adjust the level of the MASTER outputs.

!3 BOOTH OUTPUT control

Adjusts the level of BOOTH output.

!4 CUE SELECT switch

This switch is used to select the signal for CUE. Selected CUE sound will send to the headphone.

y GAIN control

Adjusts the gain of each input channel.

!5 Headphone PAN control

This function allows you to monitor the CUE level as well as the MASTER output in your headphones. A CUE Level may only be monitored of the CUE signal is selected. Serves two purposesIn the STEREO mode it changes the relative levels of the CUE and MASTER mixed together in both ear cups. In the SPLIT CUE mode it changes the balance between the monaural CUE sound in the left and monaural MASTER sound in the right.
u EFFECT LOOP WET/DRY control
Use this to adjust the ratio of original and effected sound.

i EQ ON/OFF button

When the LED is lit, EQ is ON. Otherwise EQ is bypassed.

o PGM BALANCE control

Adjusts the L/R balance of the PGM input.

!6 PHONES LEVEL control

Adjusts the headphone output level.

!7 Input select switch

Switches between the PHONO/LINE and LINE inputs. When the lever of switch is vertical position, the LINE2 or LINE4 input is selected. When the lever of switch is slope, the PHONO1/LINE1 or PHONO2/lINE3 input is selected. You can perform 8 direction placement. See page 10.

(2) Rear panel

(3) Front panel
@4 Power operation switch (POWER)
Selects power ON or OFF. NOTE: Whenever the power switch is in the OFF state, the AC adaptor is still connected on AC line voltage. Please be sure to unplug the cord when you dont use for along time.
#2 PHONO1, 2 / LINE1, 3 input jacks
These stereo pairs of unbalanced RCA jacks are inputs for a PHONO (RIAA) stage for magnetic (MM) cartridges or a LINE stage suitable for any device, such as a CD player.
#8 CH 1/2 FADER START switches
Use this to switch the Channel Fader Start function ON and OFF.
#9 CROSSFADER START A, B switches
Use this to switch the Crossader Start function ON and OFF.

#3 LINE2, 4 input jacks

These stereo pairs of unbalanced RCA jacks are inputs for any line level device.

!8 SPLIT CUE button

In the STEREO mode, the stereo sound of MASTER and CUE are fed to both ear cups. In the SPLIT CUE mode, the headphone circuit provides monaural CUE sound to the left and monaural MASTER sound to the right. When the Level Meter mode select switch is set to MASTERIn the STEREO mode, the meter indicates the stereo level in the L/R Master output. In the SPLIT CUE mode, the monaural CUE sound level is displayed on the left and the monaural MASTER sound level is displayed on the right. In the SPLIT CUE mode, the LED is lit.

@5 BALANCED MASTER OUT jacks
These 1/4 TRS jacks provide a balanced line level output. Connect these jacks to the balanced analog input jacks on an amplifier or console. Pin layout: Tip=Hot Ring=Cold Sleeve=GND

$0 HEADPHONE output jack

Accept 1/4 stereo headphone plugs.

#4 AUX INPUT jacks

This stereo pair of RCA jacks provides an unbalanced line level input with independent top panel AUX INPUT control. This input is mixed after the Crossfader and EFFECT LOOP.

$1 CH 1/2 FADER CONTOUR

adjustment
Adjusts the curve of the CH1/2 faders between fast, normal , or slow fade.
@6 EFFECT LOOP SEND/RETURN jacks
These 1/4 TS stereo jacks allow external processing of the program signal. When connect monaural type effect processor, use Lch input and output.

#5 BOOTH OUT jacks

This stereo pair of RCA jacks is the same as the MASTER output with independent BOOTH LEVEL control. This output may be for recording, booth/zone monitoring, or for connecting to another mixer.
$2 CH 1/2 FADER REVERSE switch
Reverses the direction of each respective input CH1/2 fader.
@7 MIC BALANCED INPUT jack
Accepts an balanced microphone with 1/4 TRS mono jacks. Pin layout: Tip=Hot Ring=Cold Sleeve=GND

$3 CROSSFADER CONTOUR

Adjusts the shape of the crossfader curve from a fast cut for scratching or to a slow fade for mixing.
!9 PGM 1/2 KILLS switches
These switches are used cut out the Treble, Mid or Bass frequencies of the incoming audio signal. When these switches moved up or down, the selected frequency level is cut, the LED located directly above the specific switch will glow indicating the cut function has been activated.
#6 UNBALANCED MASTER OUT jacks
This stereo pair of RCA jacks provides an unbalanced line level output. Connect these jacks to the unbalanced analog input jacks on an amplifier or console.

@8 MIC EFFECT LOOP jack

These 1/4 TRS jack allow external processing of the program signal. Pin layout: Tip=SEND Ring=RETURN Sleeve=GND
$4 CROSSFADER REVERSE switch
Reverses the direction of the crossfader.

#7 AC IN

Input connection for the included AC adaptor. NOTE: Use specified attached AC adaptor only.
@0 Level meter mode select switch
The position of this switch will determine the Level Meter mode. In the MASTER position, the meter will detail the out level of the left and right channels. In the PGM 1/2 position, the left side of the meter will indicate monaural level of the PGM 1 and the right side of the meter will indicate monaural level of the PGM 2.

@9 PGM1, 2 FADER output jacks
Connect these jacks to the FADER input jacks of DN-S3000, DN-S5000, DN-S1000 and etc. using the 3.5mm stereo mini cord.
#0 Phono ground screw (GND)
This screws provide a place to connect the ground wire from a turntable. This terminal is exclusively for a turntable ground and not a safety earth ground.

@1 Channel Fader

Controls the channel output level.
#1 PHONO1, 2 / LINE1, 3 switches

(LN / PH)

These switches change the input from PHONO to a LINE level input. These switches set a LINE level input when turntable is not connected. NOTE: Always be sure main power is shut off before change the position of the Line Level Selector Switch.

@2 Level meter

The dual LED's indicators are used to detail either the master output level, a combination of the master output level and the CUE signal level, or the PGM1/2 monaural level.

@3 Crossfader

Fades the overall mixer output between channels 1 and 2.

3 CONNECTIONS

Refer to the connection diagram below. 1. Make certain AC power is off while making connections. 2. Quality cables make a big difference in fidelity and punch. Use high-quality, audio cables. 3. Do not use excessively long cables. Be sure plugs and jacks are securely fastened. Loose connections cause hum, noise, or intermittents that could damage your speakers. 4. Connect all stereo input sources. Then connect any effects into the stereo effect, if used. Connect your microphone(s) and monitor headphones. Make sure all faders are at zero and the unit is off. Take care to connect only one cable at a time. pay attention to L and R position of jacks, on both the DN-X300 and outboard gear. 5. Connect the stereo outputs to the power amplifier(s) and/or tape deck(s) and/or MD recorder(s) and/or CD recorder(s). Plug the DN-X300 into AC power outlet.
NOTE: Always switch on your audio input sources such as CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input units.
Main balanced power amplifier

Effects processor

Balanced microphone

IN Send (Tip)

OUT Return (Ring)

1/4 TRS jack

1/4 TS jack.

1/4 TS jack

1/4 TRS mono jack
AA-26 : for AC 120V AA-27 : for AC 230V

AC adaptor

L R L R R L R L R L R L R L

To power outlet

ANTI-S ANTI-S

TING KA

KEY ADJUST

SLOW BRAKE

Quartz

START /STOP 33

START /STOP

DP-DJ151 Digital

Turntable 2

Turntable 1

NOTE: Use specified attached AC adaptor only.
Main unbalanced power amplifier
Booth unbalanced power amplifier
Mixer CD player CD player

3.5 mm stereo mini cord

4 SPECIFICATIONS
Phono Inputs: Input Impedance Level Line Inputs: Input Impedance Level EQ Control (Line): Control Range 2 Stereo 50 k/kohms 50 dBV (3 mV) 2 Stereo 20 k/kohms 14 dBV (200 mV) Unbalanced RCA jacks
Mic Send Output: Output Impedance Level Headphone Output: Output Impedance Level Power Source:
1 mono 1 k/kohms 14 dBV (200 mVrms) Stereo 33 /ohms 0 dBV (1 Vrms) AC 10 V 750 mA x 2
Tip of 1/4 TRS jacks (10 k/kohms load)

Unbalanced RCA jacks

(32 /ohms load)
3 Bands HI : 30 dB to +10 dB (at 16 kHz), 38 dB to +10 dB (at 20 kHz) MID : 38 dB to +10 dB (at 01 kHz) LOW : 38 dB to +06 dB (at 060 Hz) Stereo 20 k/kohms 14 dBV (200 mV) Stereo 20 k/kohms 14 dBV (200 mV) 1 Mono 2 k/kohms 54 dBV (2 mV) 20 Hz to 20 kHz (3 dB) 66dB Unbalanced 1/4 TS jack
Power Supply, Consumptions: USA, Canada AC 120 V 10 %, 60 Hz Europe, Asia, Oceania AC 230 V 10 %, 50 Hz Unit Size Mass 228 (W) x 326 (D) x 90 (H) mm Unit : 3.8 kg
(AC adaptor : AA-26) (AC adaptor : AA-27)
Return Inputs: Input Impedance Level Aux Inputs Input Impedance Level Mic Inputs: Input Impedance Level Frequency Response S/N EQ Control (Mic): Control Range Mic Return Inputs: Input Impedance Level Master Output: Balanced Output Impedance Level Frequency Response THD+N S/N Cross Talk Unbalanced Output Impedance Level Frequency Response THD+N S/N Cross Talk Booth Output: Output Impedance Level Send Output: Output Impedance Level

AC adaptaor : 0.5 kg

Specifications and design are subject to change without notice for purpose of improvement. Unbalanced RCA jacks

18.2 Active Balanced 1/4 TRS jack
1 Mono 20 k/kohms 14 dBV (200 mV) Stereo 150 /ohms +4 dBm (1.23 Vrms) 20 Hz to 20 kHz (2 dB) LINE : Below 0.05 % LINE : 90 dB Over 75 dB Stereo 1 k/kohms 0 dBV (1 Vrms) 20 Hz to 20 kHz (2 dB) LINE : Below 0.05 % LINE : 90 dB Over 75 dB Stereo 1 k/kohms 0 dBV (1 Vrms) Stereo 1 k/kohms 14 dBV (200 mVrms)

Ring of 1/4 TRS jack

Active Balanced 1/4 TRS jack (600 /ohms load)
PHONO : Below 0.07 % PHONO : 79 dB Unbalanced RCA jacks (10 k/kohms load) PHONO : Below 0.07 % PHONO : 79 dB Unbalanced RCA jacks (10 k/kohms load) Unbalanced 1/4 TS jacks (10 k/kohms load)
2 Bands HI : 12 to +12 dB (at 10 kHz) LOW : 12 to +12 dB (at 100 Hz)

5 FADER START

If the separately sold DN-S5000, DN-S3000, DN-S1000 and etc. players are connected to LINE1, 2, 3 or 4, they can be started using the source input fader (Ch. Fader) or Crossfader, as long as the 3.5 mm stereo mini cords have been connected.

Channel Fader Start

Turn the CH 1/2 FADER START switches #8.

Crossfader Start

Turn the CROSSFADER START A, B switches #9.
Move the Channel fader @1 of CH-1 or CH-2 control all the way to the bottom.

R L R L R R

LINE OUT L

FADER PGM2

FADER PGM1
Slide the Crossfader @3 all the way in direction opposite the source you want to start. (In the following example, startup is done with the CD player connected to PGM1.)
Set the standby mode on CD player. Use the CH 1/2 FADER CONTOUR controls $1 to control the Channel fader startup curve.
Set the standby mode on CD player. Use the CROSSFADER CONTOUR control $3 to control the Crossfader startup curve.

CD player (DN-S3000)

When you want to start the player, move up the Channel fader @1 and the CD player will begin playing.
When the Crossfader @3 is slid in the opposite direction, CD player play will begin.
NOTE: When the CH 1/2 FADER REVERSE switch is set to ON, the Channel fader's operating direction is reversed.

(1)-2, 5 (2)-1 (1)-1

(1)-2, 5 (2)-2, 5 (2)-1 (1)-1 (1)-4
NOTES: When the CROSSFADER REVERSE switch is set to ON, the Crossfader's operating direction is reversed. Channel Fader Start and Crossfader Start for the same source will not operate simultaneously. You must select from either one. If both CH FADER START and CROSSFADER START A, B switches are ON, priority will be the cross fader.

DJ MIXER

DN-X100
OPERATING INSTRUCTIONS INSTRUCCIONES DE OPERACION

FOR ENGLISH READERS

5 ~ PAGE

PARA LECTORES DE ESPAOL

PAGINA 11 ~ PAGINA 16

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

SAFETY INSTRUCTIONS

1. 2. 3. Read Instructions All the safety and operating instructions should be read before the product is operated. Retain Instructions The safety and operating instructions should be retained for future reference. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. Follow Instructions All operating and use instructions should be followed. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 15. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 16. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance this indicates a need for service. 22. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PESONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

4. 5. 6. 7.

WARNING: TO
PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

LABELS:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
2. Do not open the top cover
In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON dealer.

ATTENTION

POUR VITER LES CHOCS LECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND.
10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

3. Do not place anything inside
Do not place metal objects or spill liquid inside the DJ mixer. Electric shock or malfunction may result. Please, record and retain the Model name and serial number of your set shown on the rating label. Model No. DN-X100 Serial No.
FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT
GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE

ENGLISH

ESPAOL
TOP PANEL DIAGRAM / DIAGRAMA DEL PANEL SUPERIOR
REAR PANEL DIAGRAM / DIAGRAMA DEL PANEL POSTERIOR

ty u u y t

w q !7 !6 !3 !5
!0 !1 !2 !3 @7 @6 @5 @4 @3 @2 @5 @4 @3 @2 @1
FRONT PANEL DIAGRAM / DIAGRAMA DEL PANEL FRONTAL
NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A LUTILISATION / NOTE SULLUSO NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA
DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive. BEREINSTIMMUNGSERKLRUNG Wir erklren unter unserer Verantwortung, da dieses Produkt, auf das sich diese Erklrung bezieht, den folgenden Standards entspricht: EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3. Entspricht den Verordnungen der Direktive 73/23/EEC, 89/336/EEC und 93/68/EEC. DECLARATION DE CONFORMITE Nous dclarons sous notre seule responsabilit que lappareil, auquel se rfre cette dclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. Daprs les dispositions de la Directive 73/23/EEC, 89/336/EEC et 93/68/EEC. DICHIARAZIONE DI CONFORMIT Dichiariamo con piena responsabilit che questo prodotto, al quale la nostra dichiarazione si riferisce, conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. In conformit con le condizioni delle direttive 73/23/EEC, 89/336/EEC e 93/68/EEC. QUESTO PRODOTTO E CONFORME AL D.M. 28/08/95 N. 548
DECLARACIN DE CONFORMIDAD Declaramos bajo nuestra exclusiva responsabilidad que este producto al que hace referencia esta declaracin, est conforme con los siguientes estndares: EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3. Siguiendo las provisiones de las Directivas 73/23/EEC, 89/336/EEC y 93/68/EEC. EENVORMIGHEIDSVERKLARING Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt, waarop deze verklaring betrekking heeft, in overeenstemming is met de volgende normen: EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3. Volgens de bepalingen van de Richtlijnen 73/23/EEC, 89/336/EEC en 93/68/EEC. VERENSSTMMELSESINTYG Hrmed intygas helt p eget ansvar att denna produkt, vilken detta intyg avser, uppfyller fljande standarder: EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3. Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC och 93/68/EEC.

Do not let insecticides, benzene, and thinner come in contact with the set. Lassen Sie das Gert nicht mit Insektiziden, Benzin oder Verdnnungsmitteln in Berhrung kommen. Ne pas mettre en contact des insecticides, du benzne et un diluant avec lappareil. Assicuratevvi che lunit non venga in contatto con insetticidi, benzolo o solventi. No permita el contacto de insecticidas, gasolina y diluyentes con el equipo. Laat geen insektenverdelgende middelen, benzine of verfverdunner met dit apparaat in kontakt komen. Se till att inte insektsmedel p spraybruk, bensen och thinner kommer i kontakt med apparatens hlje.
FCC INFORMATION (For US customers)

1. PRODUCT

Never disassemble or modify the set in any way. Versuchen Sie niemals das Gert auseinander zu nehmen oder auf jegliche Art zu verndern. Ne jamais dmonter ou modifier lappareil dune manire ou dune autre. Non smontate mai, n modificate lunit in nessun modo. Nunca desarme o modifique el equipo de ninguna manera. Nooit dit apparaat demonteren of op andere wijze modifiren. Ta inte isr apparaten och frsk inte bygga om den.

3. NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the product into an outlet on a circuit different from that to which the receiver is connected. Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.

(For sets with ventilation holes) Do not obstruct the ventilation holes. Die Belftungsffnungen drfen nicht verdeckt werden. Ne pas obstruer les trous daration. Non coprite i fori di ventilazione. No obstruya los orificios de ventilacin. De ventilatieopeningen mogen niet worden beblokkeerd. Tpp inte till ventilationsppningarna.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
CAUTION The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. No naked flame sources, such as lighted candles, should be placed on the apparatus.
Please be care the environmental aspects of battery disposal. The apparatus shall not be exposed to dripping or splashing for use. No objects filled with liquids, such as vases, shall be placed on the apparatus.

2 INTRODUCTION

Thank you very much for purchasing the DENON DN-X100 DJ MIXER. DENON proudly presents this advanced DJ MIXER to audiophiles and music lovers as a further proof of DENONs non-compromising pursuit of the ultimate in sound quality. The high quality performance and easy operation are certain to provide you with many hours of outstanding listening pleasure.
2 PART NAMES AND FUNCTIONS

(1) Top panel

(Refer to page 3.)
q MIC ON/OFF/TALKOVER switch
When TALKOVER is selected , all signals except the microphone level are decreased by 20 dB. When at the ON or OFF position all signals remain at their standard levels.

u GAIN

Adjusts the gain of each input channel.

TABLE OF CONTENTS

i MASTER LEVEL control
Adjust the level of the MASTER output.
MAIN FEATURES..5 PART NAMES AND FUNCTIONS.5, 6 CONNECTIONS..7
SPECIFICATIONS..8 FADER START..9 ROTATING INPUT SELECT SWITCHES.10

w MIC EQ controls

Contour the frequency response of the Mic input 12 dB to +12 dB. At the center position, sound is flat.

o MASTER BALANCE control

Adjust the L/R balance of the MASTER outputs.

!0 Headphone PAN control

This function allows you to monitor the CUE level as well as the MASTER output in your headphones. A CUE Level may only be monitored of the CUE signal is selected. Serves two purposesIn the STEREO mode it changes the relative levels of the CUE and MASTER mixed together in both ear cups. In the SPLIT CUE mode it changes the balance between the monaural CUE sound in the left and monaural MASTER sound in the right.

2 ACCESSORIES

Please check to make sure the following items are included with the main unit in the carton:

e MIC LEVEL control

q Operating instructions..1 w AC adaptor...1 (AA-26 : for AC 120 V, AA-27 : for AC 230 V) Adjust the level of Mic signal.

r Source EQ controls

Contour the frequency response of the selected inputs. HI and MID: Adjusts the high-tone and mid-tone sound 40 dB to +10 dB. LOW: Adjusts the high-tone and mid-tone sound 40 dB to +6 dB. NOTE: Clipping may occur if adjustments are set to harsh.

1 MAIN FEATURES

1. 2-Channel DJ Mixer 4 LINE, 2 PHONO, 1 Microphone systems and 2 MASTER outputs are provided independently. 2. VCA controlled Channel Fader and Crossfader 3. Channel Fader and Crossfader contour adjustable This feature allows adjusting the shape of the Crossfader and Channel fader response from a gentle curve for smooth to the steep pitch required for top performance cut and scratch effects. 4. Channel Fader and Crossfader Reverse 5. Channel Fader and Crossfader Start The CD player can be started or stopped simply by increasing or decreasing the level of the Ch.fader or by using the Crossfader left to right or right to left. (This function can only be used when the DENON CD players DN-S3000, DN-S5000, DNS1000 or etc. is connected to the DN-X100.) 6. Channel Reverse function This function allows the left hand channel fader or right hand channel fader to control PGM1 or PGM2. 7. 3-Band Equalizer/Gain LOW, MID, HI and GAIN controls are available on every input channel. 8. 4 direction placement for input selector 9. Microphone Talkover function

!1 PHONES LEVEL control

Adjusts the headphone output level.

!2 SPLIT CUE button

In the STEREO mode, the stereo sound of MASTER and CUE are fed to both ear cups. In the SPLIT CUE mode, the headphone circuit provides monaural CUE sound to the left and monaural MASTER sound to the right. When the Level Meter mode select switch is set to MASTERIn the STEREO mode, the meter indicates the stereo level in the L/R Master output. In the SPLIT CUE mode, the monaural CUE sound level is displayed on the left and the monaural MASTER sound level is displayed on the right. In the SPRIT CUE mode, the LED is lit.

t Input select switch

Switches between the PHONO/LINE and LINE inputs. When the lever of switch is vertical position, the LINE2 or LINE4 input is selected. When the lever of switch is slope, the PHONO1/LINE1 or PHONO2/lINE3 input is selected. You can perform 4 direction placement. See page 10.

y CUE buttons

These buttons are used to activates a channels CUE mode, the LED above the cue button will glow when cue mode is activated. Cue mode will send a channels incoming signal to the headphones.

!3 Channel Fader

Controls the channel output level.

!4 Crossfader

Fades the overall mixer output between channels 1 and 2.

(2) Rear panel

(3) Front panel
!8 Power operation switch (POWER)
Selects power ON or OFF. NOTE: Whenever the power switch is in the OFF state, the AC adaptor is still connected on AC line voltage. Please be sure to unplug the cord when you dont use for along time.
@4 PHONO1, 2 / LINE1, 3 input jacks
These stereo pair of unbalanced RCA jacks are inputs for a PHONO (RIAA) stage for magnetic (MM) cartridges or a LINE stage suitable for any device, such as a CD player.
@8 CH 1/2 FADER START switches
Use this to switch the Channel Fader Start function ON and OFF.

!5 Level Meter

The dual LED's indicators are used to detail either the master output level, a combination of the master output level and the CUE signal level, or the PGM1/2 monaural level.
@9 CROSSFADER START A/B switches
Use this to switch the Crossader Start function ON and OFF.

@5 LINE2, 4 input jacks

These stereo pair of unbalanced RCA jacks are inputs for any line level device.

!6 CH REVERSE button

This switch allows the left hand fader or right hand fader to control PGM1 or PGM2. When the CH REVERSE mode is ON, the CH1 fader will be able to control PGM 2 sound and the CH2 fader will be able to control PGM 1 sound. NOTE: Please dont confuse with the CH 1/2 FADER REVERSE switch (#2).
!9 Balanced MASTER OUT jacks (BAL.)
These 1/4 TRS jacks provide a balanced line level output. Connect these jacks to the balanced analog input jacks on an amplifier or console. Pin layout: Tip=Hot Ring=Cold Sleeve=GND

#0 HEADPHONE output jack

Accept 1/4 stereo headphone plugs.
@6 Unbalanced MASTER OUT jacks
This stereo pair of RCA jacks provides an unbalanced line level output. Connect these jacks to the unbalanced analog input jacks on an amplifier or console.
#1 CH 1/2 FADER CONTOUR adjustment
Adjusts the curve of the CH1/2 faders between fast, normal , or slow fade.
@0 MIC BALANCED INPUT jack
Accepts an balanced microphone with 1/4 TRS mono jacks. Pin layout: Tip=Hot Ring=Cold Sleeve=GND

@7 AC IN

Input connection for the included AC adaptor. NOTE: Use specified attached AC adaptor only.
#2 CH 1/2 FADER REVERSE switch
Reverses the direction of each respective input CH1/2 fader.
@1 PGM1, 2 FADER output jacks
Connect these jacks to the FADER input jacks of DN-S3000, DN-S5000, DN-S1000 and etc. using the 3.5mm stereo mini cord.
#3 CROSSFADER CONTOUR adjustment
Adjusts the shape of the crossfader curve from a fast cut for scratching or to a slow fade for mixing.

!7 Level meter mode select switch
The position of this switch will determine the Level Meter mode. In the MASTER position, the meter will detail the out level of the left and right channels. In the PGM 1/2 position, the left side of the meter will indicate monaural level of the PGM 1 and the right side of the meter will indicate monaural level of the PGM 2.
@2 Phono ground screw (GND)
This screws provide a place to connect the ground wire from a turntable. This terminal is exclusively for a turntable ground and not a safety earth ground.
#4 CROSSFADER REVERSE switch
Reverses the direction of the crossfader.
@3 PHONO1, 2 / LINE1, 3 switches

(LN / PH)

These switches change the input from PHONO to a LINE level input. These switches set a LINE level input when turntable is not connected. NOTE: Always be sure main power is shut off before change the position of the Line Level Selector Switch.

3 CONNECTIONS

Refer to the connection diagram below. 1. Make certain AC power is off while making connections. 2. Quality cables make a big difference in fidelity and punch. Use high-quality, audio cables. 3. Do not use excessively long cables. Be sure plugs and jacks are securely fastened. Loose connections cause hum, noise, or intermittents that could damage your speakers. 4. Connect all stereo input sources. Then connect any effects into the stereo effect, if used. Connect your microphone(s) and monitor headphones. Make sure all faders are at zero and the unit is off. Take care to connect only one cable at a time. Pay attention to L and R position of jacks, on both the DN-X100 and outboard gear. 5. Connect the stereo outputs to the power amplifier(s) and/or tape deck(s) and/or MD recorder(s) and/or CD recorder(s). Plug the DN-X100 into AC power outlet.
NOTE: Always switch on your audio input sources such as CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input units.

CD player

POWER TITLE ON OFF

A PARAMETERS PUSH

EXIT/ RELOOP MEMO

EXIT/ RELOOP

PRESET TIME

NEXT TR. /B TRIM

PRESET

QUICK JUMP

CONT. /SINGLE TRACK SEARCH MP3 SEARCH MODE
CONT. /SINGLE FAST SEARCH TRACK SEARCH MP3 SEARCH MODE

FAST SEARCH

ECHO /LOOP FLANGER
FILTER FILTER DISC MODE DISC MODE ON : SCRATCH OFF : SEARCH/ BEND ON : SCRATCH OFF : SEARCH/ BEND

Turntable 2

ANTI-S

Turntable 1

TING KA

RVS RVS

KEY ADJUST KEY ADJUST PITCH

-12 -12

SLOW BRAKE SLOW BRAKE

Quartz Quartz

CUE/STUTTER
CUE/STUTTER PITCH/KEY PITCH/KEY

OFF ON

+12 +12 START /STOP

START /STOP 33

DP-DJ151 Digital

PLAY/PAUSE

DISC EJECT

RANGE PITCH BEND

1/4 TRS jack

R L R L L R R L L R

1/4 TRS mono jack
Main balanced power amplifier
AA-26: for AC 120V AA-27: for AC 230V AA-26 or AA-27 To power outlet AC ADAPTOR
Main unbalanced power amplifier
Note: Use specified attached AC adaptor only.

3.5 mm stereo mini cord

DRAG-S

Balanced microphone

4 SPECIFICATIONS
Phono Inputs: Input Impedance Level Line Inputs: Input Impedance Level EQ Control (Line): Control Range 2 Stereo 50 k/kohms 50 dBV (3 mV) 2 Stereo 20 k/kohms 14 dBV (200 mV) Unbalanced RCA jacks

Unbalanced RCA jacks

3 Bands HI: 30 dB to +10 dB (at 16 kHz), 38 dB to +10 dB (at 20 kHz) MID: 38 dB to +10 dB (at 01 kHz) LOW: 38 dB to +06 dB (at 060 Hz) 1 Mono 2 k/kohms 54 dBV (2 mV) 20 Hz to 20 kHz (3 dB) 66dB Active Balanced 1/4 TRS jack
Mic Inputs: Input Impedance Level Frequency Response S/N EQ Control (Mic): Control Range Master Output: Balanced Output Impedance Level Frequency Response THD+N S/N Cross Talk Unbalanced Output Impedance Level Frequency Response THD+N S/N Cross Talk Headphone Output: Output Impedance Level Power Source:
2 Bands HI: 12 to +12 dB (at 10 kHz) LOW: 12 to +12 dB (at 100 Hz) Stereo 150 /ohms +4 dBm (1.23 Vrms) 20 Hz to 20 kHz (2 dB) LINE : Below 0.05 % LINE : 85 dB Over 75 dB Stereo 1 k/kohms 0 dBV (1 Vrms)V 20 Hz to 20 kHz (2 dB) LINE : Below 0.05 % LINE : 85 dB Over 75 dB Stereo 33 /ohms 0 dBV (1 Vrms) AC 10 V 750 mA x 2 Active Balanced 1/4 TRS jack (600 /ohms load) PHONO : Below 0.07 % PHONO : 76 dB Unbalanced RCA jacks (10 k/ohms load) PHONO : Below 0.07 % PHONO : 76 dB

(32 /ohms load)

Power Supply, Consumptions: USA, Canada AC 120 V 10 %, 60 Hz (AC adaptor : AA-26) Europe, Asia, Oceania AC 230 V 10 %, 50 Hz (AC adaptor : AA-27) Unit Size 220 (W) x 226 (D) x 85.4 (H) mm Mass 2.8 kg AC adaptor : 0.5 kg
Specifications and design are subject to change without notice for purpose of improvement.

5 FADER START

If the separately sold DN-S5000, DN-S3000, DN-S1000 and etc. players are connected to FADER PGM1 or PGM2, they can started using the Channel fader or Crossfader, as long as the 3.5 mm stereo mini cords have been connected.

Channel Fader Start

Turn on the CH 1/2 FADER START switches @8.

Crossfader Start

Turn on the CROSSFADER START A, B switches @9.

DEL NO. DELE NO.

DN-S1000

MODEL NO.

MADE IN JAPAN FABRIQUE AU JAPO
Move the Channel fader !3 of CH-1 or CH-2 control all the way to the bottom.

LINE OUT

FADER LINE OUT FADER PGM1
Slide the Crossfader !4 all the way in direction opposite the source you want to start. (In the following example, startup is done with the CD player connected to PGM1.)

LINE2 FADER PGM2

Set the standby mode on CD player. Use the CH 1/2 FADER CONTOUR controls #1 to control the Channel fader startup curve.
Set the standby mode on CD player. Use the CROSS FADER CONTOUR control #3 to control the Crossfader startup curve.

CD player (DN-S1000)

FADER PGM1

FADER PGM2

MEMO CLR
When you want to start the player, move up the Channel fader !3 and the CD player will begin playing.

1-MIN. SKIP

CONT. /SINGLE

FLANGER

FILTER DISC MODE
When the Crossfader !4 is slid in the opposite direction, CD player play will begin.

(1)-2, 5

(1)-2, 5 (2)-2, 5 (2)-1 (1)-1
NOTE: When the CH 1/2 FADER REVERSE switch is set to ON, the corresponding fader's operating direction is reversed.

(2)-1 (1)-1

NOTES: When the CROSS FADER REVERSE switch is set to ON, the Crossfader's operating direction is reversed. Channel Fader Start and Crossfader Start for the same source will not operate simultaneously. You must select from either one. If both CH FADER START and CROSSFADER START A, B switches are ON, priority will be the Crossfader.
6 ROTATING INPUT SELECT SWITCHES
1. Disconnect the power. 2. Remove knobs from the Top Panel. 3. Remove the 6 screws attaching the Top Panel. 4. Remove the 2 screws attaching the Switch unit. 5. Rotate the Switch unit to the desired location. 6. Reinstall the 2 screws holding the Switch unit. 7. Reinstall the Top Panel and reattach knobs. (For RCA PINJACK)