Reviews & Opinions
Independent and trusted. Read before buy Oldsmobile Aurora 1998!

Oldsmobile Aurora 1998

Manual

Download (English)
Oldsmobile Aurora 1998, size: 19.6 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Oldsmobile Aurora 1998About Oldsmobile Aurora 1998
Here you can find all about Oldsmobile Aurora 1998 like for sale and other informations. For example: .

Oldsmobile Aurora 1998 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Oldsmobile Aurora 1998 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Oldsmobile Aurora 1998 photo ]

Video review

1998 Oldsmobile Aurora Start Up, Engine, and In Depth Tour

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc1

#03-02-36-002: SMU - Revised Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement Procedure and Steering Wheel Position Sensor Centering Procedure - (Jul 30, 2003)
Subject: Revised Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement Procedure and Steering Wheel Position Sensor Centering Procedure 1998-2003 Buick LeSabre, Park Avenue 1998-2003 Cadillac DeVille, Seville 2003 Cadillac CTS 1998-2003 Chevrolet Corvette 1998 Oldsmobile Achieva 1998-2002 Oldsmobile Intrigue 1998-2003 Oldsmobile Aurora 1999-2003 Oldsmobile Alero 1998-2003 Pontiac Bonneville, Grand Am 1998-2000 Chevrolet C/K Pickup Models 1998-2003 Chevrolet Suburban, Tahoe 1999-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 1998-1999 GMC Suburban 1998-2000 GMC C/K Pickup Models 1998-2003 GMC Yukon 1999-2003 GMC Sierra 2000-2003 GMC Yukon Denali, Yukon XL 2003 GMC Sierra Denali

Models:

This bulletin is being issued to revise the Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement procedure in the Variable Effort Steering (1998-2001 model years) or Steering Wheel and Column (2002-2003 model years) and add the Steering Wheel Position Sensor Centering procedure in the Steering Wheel and Column sub-sections of the Service Manual. Please replace the current information in the Service Manual with the following information. The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page.
Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement

Removal Procedure

Caution: Refer to SIR Caution in Cautions and Notices. 1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the steering column from the vehicle. Refer to Steering Column Replacement. 3. Remove the following from the steering shaft: 3.1. steering shaft seal (7) 3.2. sensor retainer (6) 3.3. steering wheel position sensor (5), refer to Steering Wheel Position Sensor Centering. 3.4. 2 lower spring retainers (4) 3.5. lower bearing spring (3) 3.6. lower bearing seat (2) 3.7. adapter and bearing assembly (1)

Installation Procedure

1. Install the following onto the steering shaft:
1.1. adapter and bearing assembly (1) 1.2. lower bearing seat (2) 1.3. lower bearing spring (3) 1.4. 2 lower spring retainers (4) 1.5. steering wheel position sensor (5) refer to Steering Wheel Position Sensor Centering. 1.6. sensor retainer (6) 1.7. steering shaft seal (7) 1.8. Enable the SIR system. Refer to in SIR. 2. Install the steering column to the vehicle. Refer to Steering Column Replacement. 3. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR.
Steering Wheel Position Sensor Centering
Important: Identify the type of steering wheel position sensor from the illustrations below BEFORE removing the sensor from the steering column. Once you have identified the steering wheel position sensor, follow the instructions listed in the removal procedure. 1. Verify the type of steering wheel position sensor.

2. From the technicians point of view, the FRONT of the sensor (1) connector will be on the right. Important: If reusing the existing sensor, you do not have to align the sensor before removal. Centering is not required when it is time to reinstall. 3. Remove the connector from the sensor. 4. Remove the sensor (1) from the adapter and bearing assembly. 5. To install the sensor, proceed to step 1 in the installation section.
6. From the technicians point of view, the FRONT of the sensor will have: A foam ring (2) A pin hole (1) for centering the pin (note location of the pin hole) A flush rotor flange cuff (4) Important: If reusing the existing sensor, you must make an alignment mark on the rotor flange cuff (3) before removing the sensor. Failure to do so will cause misalignment when installing the sensor. A new sensor will be required if misaligned. 7. 8. 9. 10. Make an alignment mark on the flush rotor flange cuff (3). Remove the connector from the sensor. Remove the sensor from the adapter and bearing assembly. To install the sensor, proceed to step 5 in the installation section.
11. From the technicians point of view, the FRONT of the sensor will have: A raised rotor flange cuff (3) An alignment mark (2) on the rotor flange cuff (3) for installation A pin hole (1) for the centering pin (note location of the pin hole) 12. Remove the connector from the sensor. 13. Remove the sensor from the adapter and bearing assembly. 14. To install the sensor, proceed to step 9 in the installation section.
15. From the technicians point of view, the FRONT of the sensor will have: A raised rotor flange cuff (3) An alignment mark (2) on the rotor flange cuff (3) for installation A pin hole (1) for the centering pin (note location of the pin hole) 16. 17. 18. 19. A sensor clip in FRONT of the sensor Remove the connector from the sensor. Remove the sensor clip from the sensor. Remove the sensor from the adapter and bearing assembly. To install the sensor, proceed to step 13 in the installation section.

20. From the technicians point of view, the FRONT of the sensor will have: A flush rotor flange cuff (3) A pin hole (1) for the centering pin (note location of the pin hole) An alignment mark (2) on the flush rotor flange cuff (3) for installation 21. Remove the connector from the sensor. 22. Remove the sensor from the adapter and bearing assembly. 23. To install the sensor, proceed to step 17 in the installation section.
24. From the technicians point of view, the FRONT of the sensor will have: A flush rotor flange cuff (4) A pin hole (2) for the centering pin (note location of the pin hole) An alignment mark (3) on the flush rotor flange cuff (4) for installation A foam ring (1) 25. Remove the connector from the sensor. 26. Remove the sensor from the adapter and bearing assembly. 27. To install the sensor, proceed to step 21 in the installation section.
Important: If reusing the existing sensor, no centering of the sensor is required. 1. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. 2. From the technicians point of view, the FRONT of the sensor (1) connector will be on your right. From the technicians point of view, the BACK of the sensor (2) connector will be on your
left. 3. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 4. Install the connector to the sensor.
5. From the technicians point of view, the FRONT of the sensor will have: A foam ring (4) A pin hole (7) for the centering pin (note location of the pin hole) A flushed rotor flange cuff (6) An alignment mark (5) for installation 6. From the technicians point of view, the BACK of the sensor will have: Double D flats (1) A foam ring (3) An alignment tab (2) for installing into the adapter and bearing assembly. A view of the inside of the connector Important: If reusing the existing sensor, you must align the marks on the flush rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor. 7. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 8. Install the connector to the sensor.

9. From the technicians point of view, the FRONT of the sensor will have: A pin hole (3) for the centering pin (note location of the pin hole) A raised rotor flange cuff (5) An alignment mark (4) for installation 10. From the technicians point of view, the BACK of the sensor will have: Double D flats (1) An alignment tab (2) for installing into the adapter and bearing assembly. Important: If reusing the existing sensor, you must align the marks on the raised rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor. 11. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 12. Install the connector to the sensor.
13. From the technicians point of view, the FRONT of the sensor will have: A pin hole (2) for the centering pin (note location of the pin hole)
A raised rotor flange cuff (4) An alignment mark (3) for installation 14. From the technicians point of view, the BACK of the sensor will have an alignment tab (1) for installation. This sensor does not have double D flats. Important: If reusing the existing sensor, you must align the marks on the raised rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor. 15. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 16. Install the connector to the sensor.
17. From the technicians point of view, the FRONT of the sensor will have: A pin hole (2) for the centering pin (note location of the pin hole) A flush rotor flange cuff (4) An alignment mark (3) for installation 18. From the technicians point of view, the BACK of the sensor will have an alignment tab (1) for installation. This sensor does not have double D flats. Important: If reusing the existing sensor, you must align the marks on the flush rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor. 19. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 20. Install the connector to the sensor.

21. From the technicians point of view, the FRONT of the sensor will have: A pin hole (3) for the centering pin (note location of the pin hole) A flush rotor flange cuff (5) An alignment mark (4) for installation A foam ring (6) 22. From the technicians point of view, the BACK of the sensor will have: Double D flats (1) An alignment tab (2) for installing into the adapter and bearing assembly. Important: If reusing the existing sensor, you must align the marks on the flush rotor flange cuff before installation. The alignment mark must stay aligned until the sensor is seated into the adapter and bearing assembly. If installing a new sensor, it will come with a pin installed in the sensor. Do not remove the pin until the sensor is seated. If the new sensor did not come with a pin installed, you must reorder a new sensor. 23. Looking at the FRONT of the sensor, align the sensor with the steering shaft and install into the adapter and bearing assembly. 24. Install the connector to the sensor.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

 

Tags

Hssk40-50 SL-BD22D TH-37PX80 DWL-610 L1752T S 3000 Azur 550A Linea 198 Wd-52825 GR15vtcan KDL-40SL150 FO-51 Aspire E560 Wfmc2201UC Korg 770 - 70 530 1FM DR-4010C TDM-NW10 To Life Scanmaker 3700 VGN-FZ21MR ES-8078 Factory FL125 Watch 3111 SS-XB80V Focus A-3440 Freestyle P-7000 253 TC YZ125-1998 YZF-R6s-2008 23 V LD190 AJ260 37B Polaroid A932 MS202II RM-V8a T S Tomb 6561GM 2033SW Plus MP171SPF Bizhub C652 Factor PC DAV-DZ230 Controller CD401 ER8312B LX3700D RT-39NZ43RB CL-21Z43MJ - 1989 LCD-plasma-IFC230 SC-AK47 PS-50C6H Cantibmlp Pentax Esii Extensa-5220 6317dwde LFV1260 TC-WE835S DNS-323 SCS 178 Dictionary Multitrim 250D SGH-X620 EX5-EX7-ex5R BG-35 7100R 610 S HS06THB T5620 F65011VI CMT-EH10 SB-29S HT-WS1 Optio WPI DV-SP503E YP-S5JAB KX-THA13 RSA1ztwp Bremen CD72 AV-452 SUB-zero 561 Part2 5610Z Vluu I100 JX20 Pura UX-238 Altea XL DVD-S97EB Abrasives PMA400 CT-5361E Lexmark W820 807si ME-50-ME-30 KC 350

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101