Porsche 944 Dash Removal and Installation

Scott Levy

I. II. III. IV. V. VI. VII. VIII. IX. X. XI. XII. XIII. XIV. XV. XVI. XVII. XVIII. XIX. XX. XXI. XXII. XXIII.
Introduction Remove the steering wheel. Remove the center console. Remove the sun visors. Remove A-pillar trim. Remove instrument cluster trim. Remove climate control trim and climate control. Remove steering wheel trim. Remove instrument cluster Remove glove box trim (piece with clock, hazard switch, lock, etc.). Remove glove box. Remove dash. Install replacement dash. Install instrument cluster. Install glove box trim. Install steering wheel trim. Install glove box. Install climate control and trim. Install instrument cluster trim. Install A-pillar trim. Install the center console. Install the steering wheel. Final inspection.

I. Introduction

Replacing the dash on a late model, 85.5 and newer Porsche 944, is not a difficult task. It is very time consuming and meticulous. Patience is necessary. An extra pair of hands is not required, but will make some parts of the job easier. Im assuming you have a standard shift, and no airbags. I have not seen the underside of a dash with airbags and Im not sure that I want to. Read through this whole guide before taking on the job. Youll have a better idea to how things fit together. Its a big 3D puzzle. Also, I take no responsibility for damage you incur while using this guide. This is a guide only. This is not meant to replace service manuals or professional assistance. In other words, if you dont think this is good enough for you, dont use it and seek out a professional. I have tried to be as complete as possible, but I may have left something out. I recommend having a system to safely store the screws that come off the dash. Porsche uses different sizes, many looking very similar. A couple of ideas, use sandwich bags to store the screws for the trim piece associated with it, or use small dixie cups. Make sure to label the bag/cup with what trim piece it goes to. A source for extra screws is a plus. Many of our dashes dont have all their original hardware. You may have to transfer some parts from your dash to the new dash. Side vents, glove box door and lock, center console mounting brackets, etc. I would recommend having a pad and pencil ready to make notes as you go along. When you are reinstalling the dash, possibly 4-5 days later, you will need some sort of memory refresher. I used a Polaroid camera to take pictures of how things fit together and what wiring harness went where. The car will give you problems while doing this project. Expect it. When doing this, I couldnt get the top screw out from my passenger side A-pillar trim. I ended up having to drill the head off it to get the trim out. I was then left with a stub of a screw sticking out. I cut it off with a dremel, drilled a new hole right next to and used a new screw. Its not the optimal way to repair this, but it worked and is a good example of unexpected trouble. Also, youll probably break something. Do this job over a few days to give yourself time to find replacement parts. Youll be much happier knowing you have a good piece in the dash instead of something you may have to glue to get working right. Disconnect the negative battery cable. I didnt do this and wound up replacing just about every dash light bulb and a number of fuses. A note on disconnecting the wiring harness from the dash switches. This is not really easy to do. Ive found its better to be very patient and use a small blade to pry with than to squeeze, yank, pull, or use brute force. Using brute force, youll either break the clips that hold the harness to the switch or the clips that hold the switch to the trim. Remember, most of our cars are at least 10 years old and the plastic gets brittle. Lets get started
II. Remove the Steering Wheel
1) Remove the horn pad. This is done by pulling on the pad, very hard. The pad may seem like it wont come off, keep pulling. 2) Disconnect the horn ground wire from the back of the pad. 3) Using a 15/16 or a 28mm socket remove the retaining nut from the steering wheel. There will also be a washer behind the nut, remove it. 4) Make sure the wheel is straight. Remove the wheel by pulling it off the yoke.
III. Remove the Center Console
1) 2) 3) 4) 5) 6) 7) Remove the ashtray. Remove the radio. (Actually, you may not have to. Youll see later.) In the cassette holder, under the lid, at the rear, are two screws. Remove them. At the front of the cassette holder, where the ashtray sits, are two small screws. Remove them. You should now be able to remove the cassette holder. At the rear of the shifter trim are two small screws. Remove them. Remove the pocket that is under the radio. It just pulls out. With the shift boot still attached, you should be able to lift this trim up from the console. You will have to remove the boot from the trim. The boot is attached to the trim with a plastic ring that clips to the bottom of the trim. Carefully free the clips and the boot will come free. You should now be able to slip the trim over the shifter. Disconnect the wiring from the switches. The wiring harness should be numbered. Starting at 1 on the left. They will be reconnected in this order. Remove the center console retaining screws. One each on either side, up towards the front. Now you should be able to remove the center console. Slide it to the rear of the car. Lift it over the shifter. If you left the radio in, be sure to disconnect it first. There are 2 brackets attached to the dash used to hold the center console. One for each side of the center console. Remove these brackets from the dash and set them with the center console. You may need them for the new dash. Yes, there is a left and a right to these brackets. Note their orientation!

8) 9) 10) 11)

This is one of the brackets used to attach the center console to the dash. There is another one on the other side.
Here you see the wiring harness for the center console switches. These are numbered starting at 1 on the left most connector.
IV. Remove the Sun Visors
1) Note the orientation of the pivot end of the visor. 2) Remove the 3 screws holding the pivot end. 3) Remove the 2 screws holding the visor clip. The visor and clip should be free now. Dont lose the washers in the clip. It is necessary to do this to facilitate the removal of the A-pillar trim in the next section. Dont pull the header down too far, just enough to expose the end of the A-pillar trim.
V. Remove the A-pillar Trim
The A-pillars have 3 screws holding them into place. Black plastic covers hide the screws. 1) Remove the screw covers. 2) Remove the lower 2 screws. 3) The uppermost screw may not be visible. It is put into the trim directly vertical. If you fish around in the hole with your screwdriver, pointing straight up at the sky, you should find it. Remove this screw. 4) Loosen the door edge cover by pulling it off. (Rubbery trim going around the door opening.) 5) You can now remove the trim. Slight wiggling may be required.
VI. Remove Instrument Cluster Trim
The instrument cluster trim is the piece that frames the instrument cluster. This also includes the center vents and the trip odometer reset button. 1) Remove the 3 screws from the center vents. Be careful not to drop them into the ducts. 2) Remove the 3 screws from the top of the trim above the instruments. Use a stubby screwdriver. These screws go straight up into the dash. 3) There are 2 screws in the bottom. One on either side of the steering column. They go in from the bottom into the bottom of the trim. Remove these screws. 4) You can now remove the trim. Some wiggling may be necessary. Be careful not to scratch the instrument cluster lens. (I did!)
VII. Remove Climate Control Trim and Control Unit

If you look at the control unit trim, youll notice there are no screws. This piece is snapped on over the control unit. It covers screws behind it on each side of the control unit. 1) Gently pull off the sliders. 2) From the top of the unit, carefully pry the trim until it comes off. A small knife blade should work very well for this. There is no need to remove the knobs. 3) Once the trim is off, youll see 2 screws on each side of the control unit. Remove these screws. 4) You can now, gently, pull out the control unit from the dash. The clear plastic tabs for the screws are easily broken. BE CAREFUL! If you break a tab, you have to buy a whole control unit. 5) Remove the wiring harness from the back of the control unit. Note the orientation of the harness. Its keyed, do it anyway. The reason we start here for the dash trim is that the screws also hold the trim on each side of the control unit. If you start at one end or the other, you risk breaking the tabs off other trim pieces.
This is a picture of the climate control opening. Notice the screw location on either side of the opening. These screws hold the climate control and the trim on either side of it.
Directly above is the climate control wiring harness.
VIII. Remove Steering Wheel Trim
1) Remove turn signal assembly trim by removing 3 small screws. Trim pulls off over steering column. 2) Remove rubber surround from ignition key assembly. Slide a knife blade carefully underneath it and pull. It may be somewhat tough. Be careful not to slice the rubber or tear it. There is a metal ring at the back of this piece. It should come off with the rubber. 3) Remove the screws from this trim piece. There should be 1 in the bottom and 1 next to the steering column, may be slightly hidden. 4) You should now be able to remove the piece. Disconnect the wiring harness and note orientation. 5) Remove the headlight switch knob. Do this by pulling and wiggling. 6) There is a cover hiding 2 screws just to the left of the fog light switch. Remove the cover and the screws. 7) On the side of the dash, there is a cover with 1 screw in it. Remove the screw and the cover. This will expose 2 screws in the end of the trim. 8) Remove the 2 screws holding the upper vent. Remove the upper vent. 9) Remove the 2 screws in the trim and center the vent shutoff lever. 10) Remove remaining screws in the trim piece. One just left of the steering column and 1 on the bottom. 11) Now you have to remove the headlight switch. Remove large nut from the switch. Switch will slide out the rear of the trim piece. 12) You should now be able to remove this piece. Disconnect wiring harness from fog light switch. 13) Now you have to remove the turn signal/wiper control assembly. This is all one unit and is mounted to the steering column by a collar and one bolt. 14) Note the position of this assembly on the steering column. 15) Loosen the collar bolt. I think it a 10mm. 16) Slide the assembly off the steering column disconnecting the wiring harness as you go.

Fog light wiring

Here you can see the left side trim removed. The turn signal assembly is still on the steering column.
Headlight switch Panel dimmer
IX. Remove the Instrument Cluster
Before we get into the actual removal of this, let me talk about the wiring harness connectors used here. The connector is black plastic and there are 3 of them. They all look the same, Im not sure if they are keyed or not. The connector has 2 arms, one on each end. The purpose of the arms is to lock the connector into place. The arms lock the connector by hooking to the instrument cluster. Once hooked, the arm rotates and locks itself down. The arm locking mechanism itself works kinda like a battery door on a remoter control. You'll see what I mean when you get in there. You push down, slightly, and pull the arm out of its locked state. Ok, now that Ive totally confused you. Lets remove the instrument cluster. 1) Remove the 4 screws holding the instrument cluster into place. 2) Carefully remove the cluster from the dash. 3) Disconnect the wiring harness and note orientation. While this is out, its a good time to replace any burnt bulbs. Also, while youre in this area, note the orientation of the trip odometer reset switch. Its not really attached to the dash. Its just set into 2 locating holes. Youll want it to be exactly where it is when you put things back together.
Here you can see the wiring harness for the instrument cluster, indicated by the yellow arrows. The red arrows show 3 of 4 mounting points for the instrument cluster. In the background, you can see the duct running to the side vent on the driver side (light blue arrows). The green arrows indicate one of the locking arms for the connector and its hook on the other end.

X. Remove Glove Box Trim

Notice the little circular vent next to the cigarette lighter. This is the interior temperature sensor for the climate control system. Attached to the backside of this vent is a hose that runs to just about the firewall under the dash. Be careful not to pull the trim out too far once you have all the screws loosed. You want to disconnect the hose at the trim piece, not at the other end by the firewall. Here we go. 1) Remove the circular vent by turning it counter clockwise. Its kinda like the piece that holds the ball into the bottom of a computer mouse. 2) Inside at the bottom of the vent youll see a small screw and washer. Remove them. 3) On the end of the dash, youll find the end cover. Remove the screw that holds it and the cover. This will expose the 2 end screws for the trim piece. 4) Remove the 2 screws. 5) Just next to the vents, youll find a cover hiding 2 more screws. Remove this cover and the 2 screws under it. 6) The hazard switch, clock, cigarette lighter are attached directly to this piece. As always, be careful removing wiring harnesses.

While youre here, might be a good time to replace that broken clock.

XI. Remove the Glove Box

The glove box is held in by a number of screws in the front on each side, 2 into the top by the light and a big metal clamp at the back. This isnt hard. 1) Remove all screws on the front, sides, top of the glove box. 2) Crawl under the dash. Disconnect the air hose going to the vent in the glove box. (Yes, the glove box has air conditioning.) 3) Carefully pull the box out the front opening. Youll have to bend the top down slightly to clear the light assembly. Disconnect the wiring just after you get the light assembly clear. The glove box door is a part of the dash as well as the lock. These items can be transferred to the new dash if the replacement doesnt have them.

XII. Remove the Dash

The moment youve been waiting for! Be sure all wiring is clear. You may want to take a deep breath at this point. It isnt a pretty sight when the dash is out. 1) Remove the upper mounting screws. One in each A-pillar. 2) Remove the lower mounting screws. One in each side of the dash, down towards the bottom. 3) Gently, carefully, pull the dash straight out. Ductwork from the climate control system to the side vents will have to be removed from the dash. I dont recommend removing the ducts from the system. Leave them attached at the system end. Another set of hands comes in handy here in case you get hung up on something. 4) Have a beer, youre half way done with this project!

Side vent duct

Inside temperature sensor hose
XIII. Install Replacement Dash
Well, now youve done it! You have your dash out and youre probably scratching your head wondering how youll ever get things back together. Believe me, things go much quicker in reverse. You need to look over your firewall at this point. If you were having any climate control problems that arent related to the control unit itself (leaking heater core, mechanical issues with the system, etc.), now is the time to take care of things. The top of the firewall is covered in black felt. Look to be sure all of it is in place and in good shape. This felt prevents the metal frame of the dash from rubbing on the metal firewall and making a lot of noise. Look over your wiring harnesses for any damaged, worn, torn, wiring. If all looks good, lets put in a new dash. Looking at the firewall, youll see a small ledge covered in felt. This is where the dash rests on top. Have the top screws ready and an extra pair of hands. Ive found youll want someone to hold the dash as you manipulate it into place. If you get the dash in and it doesnt seem to fit quite right, its probably caught on something. The lower mounting brackets are easy to catch. 1) 2) 3) 4) 5) 6) Install upper side vents into new dash. Set new dash into car letting it rest on firewall ledge. Install screws in upper mount. Hand tighten only at this point. Reconnect climate control ducts to side vents. If dash looks in place, hold against firewall while installing lower mounting screws. Be sure dash is in its final resting place while tightening all screws.

XIV. Install Instrument Cluster
1) 2) 3) 4) Install instrument cluster into its dash opening. Connect wiring harness. Be sure to lock down the connector arms. Install and tighten screws. Now is a good time to be sure trip odometer reset switch is in place.
Instrument cluster mounting screws
Trip Odometer Reset switch
XV. Install Glove Box Trim
1) 2) 3) 4) Place trim piece where you connect wiring harness and temperature sensor hose. Install into dash. Install all screws and tighten except for 2 by climate control. Install dash side cover and tighten.
XVI. Install Steering Wheel Trim
1) Install turn signal/wiper switch assembly by sliding it over the steering column. Connect wiring harness as you go. 2) Be sure position of this assembly is where you want it and tighten the collar bolt. 3) Install left side trim first. Mount headlight switch and tighten nut. Connect wiring for fog light switch. 4) Install screws and tighten. The bottom screw also goes into right side trim. 5) Install headlight switch knob. Notice its keyed. 6) Install right side trim. Connect wiring harness. 7) Install all screws except 2 by climate control. Theyll go in with the climate control. 8) Install rubber surround over ignition. Press it onto ignition as far as you can. 9) Install turn signal/wiper assembly trim and tighten down with the 3 small screws. 10) Install dash side cover and tighten.
This is a shot of the steering column without the trim work on either side or the turn signal assembly. Notice the funny looking connectors.
Ignition switch Headlight switch Turn signal assembly connectors Cruise control

My foot

XVII. Install Glove Box
1) Slide the glove box into its opening in the dash. An extra helper is good here because its tough to get the box into the metal clamp on the firewall while adjusting it to clear the light assembly. Dont forget to connect the wiring for the light before putting it in. 2) Once the box is in right, connect the hose for the A/C vent. 3) Install all the screws and tighten.
XVIII. Install Climate Control Unit and Trim
1) 2) 3) 4) Connect wiring harness and slide unit into dash. Install all 4 screws and tighten. Install trim by snapping it on over control unit. Install sliders.
XIX. Install Instrument Cluster Trim

1) Slide, wiggle trim piece into place. Be sure trip odometer reset switch is in place first. 2) There is a light bulb at the top of the dash for the defroster slider that is between the center vents. Before you screw in this piece, test this light. I found after I put this piece in, I had light leaking into the center vents and elected to remove this light bulb. The purpose of this bulb is to backlight the slider. 3) If everything is ok, install all the screws. 3 by the center vents. 3 into the top of the dash. 2 on either side of the steering column.
XX. Install A-pillar Trim
1) 2) 3) 4) 5) 6) Place trim piece into position. Install and tighten screws. Tuck vinyl under door edge cover and reinstall. Repeat for other side. Reset header panel up against top of car. Reinstall sun visors and clips. Yes, there is a left and a right.
XXI. Install the Center Console
1) Remember the 2 brackets we took off the old dash in section III? Time to put them on the replacement dash. There is a left and right. 2) Slide the center console into place. 3) Install the screws holding it on each side. 4) Install and reconnect the radio if you removed it in section III. 5) Install and the trim that goes around the radio/shifter. Reconnect the wiring harness. 6) Install the shift boot and its hold down ring. 7) Install the screws at the rear of this piece that hold it into place and tighten. 8) Install the cassette holder and tighten its screws. 9) Replace the ashtray.
XXII. Install the Steering Wheel
1) 2) 3) 4) Install steering wheel straight onto column yoke. Install washer, nut and tighten. Unlock column with key and test wheel to be sure turn signals cancel as they should. Connect horn ground wire and install horn pad. Test horn. If horn doesnt work, check to be sure the wheel is making connection with the copper strips on turn signal assembly. Adjust assembly as needed. There should be about 1/8 space between the wheel and this assembly. If the wheel is too close, it will make a grinding noise when turned.

XXIII. Final Inspection

At this point, all should be back together and looking good. Reconnect the battery cable. Car should start. All dash lights should be functional. All switches and accessories should work. If something doesnt, check the wiring harness for that item and make sure its connected correctly. Check fuses. If all else fails, take that section apart and have a look. If all went back together ok, any rattles or squeaks should go away after the replacement dash settles into its new home. Mine squeaked for about a week after the job. Now its solid as a rock, not a rattle to be heard. This is a great job for the mildly mechanically inclined. It provides great satisfaction and really teaches you how to be patient when the car throws you a curve. Go out for a drive and appreciate your great work!

Remark Qty Model L M3V X

underbody protection 1 KG GLASSOHYD tin SN 90 % 200 G synthetic resin prime coat metallic 1 LTR

X X X X X X X X

L 90E L Y7A L A3B L D8A L Y5B L Y5A L Y1L
ALD 645 97A ALD 645 Z7Z ALD 645 B7V ALD 645 A1Y ALD 645 A6V ALD 645 Y7Z ALD 645 Y9V ALD 645 B8Z ALD 645 Y5V ALD 645 D3V ALD 645 Y7U ALD 645 A3Y ALD 645 Y7Y ALD 645 Y8V
diamond silver metallic gemini grey metallic graphite metallic KALAHARI-METALLIC lhasa metallic meteor metallic montego black metallic MAHAGONI-METALLIC SAPHIR-METALLIC sienna red metallic stone grey metallic surinam metallic zermatt silver metallic sable brown metallic

L 041 L M1N L M3A L M9V

synthetic resin prime coat metallic 822 garnet red metallic 30T light blue metallic 966 light bronze metallic 33N crystal green metallic 20C moss green metallic 655 platinum-metallic 708 black-metallic
L M5Z L M1V L M6Y L M6V 536 L M8U 700 L M9Y 027 L M3A L 041 L M1N 932 20

Remark Qty Model L M9V

451 mocha black paint touch-up applicator set comprising: paint touch-up applicator top-coat paint paint touch-up applicator clear lacquer L L L L L L L L L L L L L L 097 A02 0Z7 Z02 0B7 V02 0A1 Y02 0B8 Z02 0Y7 U02 0A6 V02 0Y7 Z02 0Y9 V02 0Y5 V02 0A3 Y02 0D3 V02 0Y7 Y02 0Y8 V02 diamond silver metallic gemini grey metallic graphite metallic KALAHARI-METALLIC MAHAGONI-METALLIC stone grey metallic lhasa metallic meteor metallic montego black metallic SAPHIR-METALLIC surinam metallic sienna red metallic zermatt silver metallic sable brown metallic X X X X X X X X X X X X X X X
L 97A L Z7Z L B7V L A1Y L B8Z L Y7U L A6V L Y7Z L Y9V L Y5V L A3Y L D3V L Y7Y L Y8V
paint touch-up applicator set 966 light bronze metallic 20C moss green metallic 30T light blue metallic 655 platinum-metallic 708 black-metallic 822 garnet red metallic 33N crystal green metallic
L M1V L M6V L M5Z L M8U L M9V L M3Y L M6Y

Page: 003

005-00
Description securing liquid sealing compound preservative agent securing liquid

921 00

loctite -27010 CCM high strength loctite -22110 CCM low strength sealing compound

012 00

010 00
loctite -57450 CCM loctite -63810 CCM for balance shaft loctite adhesive remover -80646spraying can adhesive sealing compound 310 CCM loctite for pasting metal glass ceramics thermoset plastic adhesive set comprising:

164 40

103-15
Pos Part Number Description driving mechanism balance shaft balance shaft balance shaft bearing shell bearing shell oversize 0.50 mm gear wheel spacer sleeve gasket flange washer washer woodruff key hexagon-head bolt M 10 X 35 tensioning roller roller washer A 10,5 lock nut M 10 toothed belt technical information group 1 NR.15/95 attention locking ring round seal 23,16 X 5,33 bearing case shaft sealing ring 30 X 47 bearing case shaft sealing ring 30 X 48 /L /L /R /R

-84 85

5 * 00 N 3

N N 149 2

219 04

145 02

16 * 00

18 * 00

20 * 281 40

Remark Qty -1 M657 Model

21 * o-ring 56,7 X 3,N 5 hexagon-head bolt M 8 X 35
hexagon-head bolt M 8 X 50 N 6 hexagon-head bolt M 8 X 60
washer A 8,02 bearing sleeve bearing sleeve oversize 0.50 mm dowel sleeve

104-00

Pos Part Number Description engine lubrication 09 oil pump M M M M
1 >> >> >> >> 41E 41E 43E 43E 1 >> >> >> >> 1 -M44.01 M44.03 M44.02 M44.41E 41E 43E 43E 1 M44.01 M44.03 M44.02 M44.4 M44.01 M44.03 M44.02 M44.M44.01 M44.03 M44.02 M44.04 M44.01 M44.03 M44.02 M44.04 M44.01 M44.03 M44.02 M44.04
use also: 944.102.216.01 944.102.243.00 (1) oil pump M 41E 09030 M 41E 20780 M 43E 14859 M 43E 21784
use also: 944.107.911.* shaft sealing ring 38 X 55 X 7 M >> 41E M >> 41E M >> 43E M >> 43E shaft sealing ring 38 X 52 X 7 M 41E 09030 >> M 41E 20780 >> M 43E 14859 >> M 43E 21784 >> toothed sleeve M >> M >> M >> M >> toothed sleeve M 41E 09030 >> M 41E 20780 >> M 43E 14859 >> M 43E 21784 >> round seal 28 X 2,58 hexagon-head bolt M 6 X 35 M 6 X hexagon-head bolt M 6 X 45

331 40

161 01

161 02

4 * 02

Pos 11 N

Part Number 7
Pos 16 Part Number Description oil separator M >> M >> M >> M >> oil separator M 41D A684 >> M 41D 5521 >> M 43D D869 >> M 43D 6294 >> round seal 20 X 5 M M M M round seal 24 X 5 M 41D A684 M 41D 5521 M 43D D869 M 43D 6294 41D 41D 43D 43D AD868 6293
Remark Qty 1 M44.01 M44.03 M44.02 M44.M44.01 M44.03 M44.02 M44.>> >> >> >> 41D 41D 43D 43D AD2 >> >> >> >> (AUS) (J) WW M44.01 M44.03 M44.02 M44.04 M44.01 M44.03 M44.02 M44.04 Model

167 E 168 E N N N 13

307-00
Pos Part Number Description central tube automatic transmission 1 > 09 N 11 central tube converter mounting clamping piece clamping screw hexagon-head bolt M 8 X 25 spring washer B 8 cap cap cap lock ring B 10 hexagon-head bolt M 10 X 35 hexagon-head bolt M 12 X 80 hexagon-head bolt M 10 X 50 spring washer B 12 washer A 13 hexagon nut M 12 spring washer B 10 clutch housing grooved pin 10 X 32 cap damper clamping piece

C 277 A N N N 2

N N N 1

255 00

Pos 32 32A 33
Remark Qty X X X X X X X Model
starter ring N 2 pan-head screw M 8 X 40
circlip 17 X 00 spacer sleeve 1,01 spacer sleeve 2,02 spacer sleeve 3,03 spacer sleeve 4,04 spacer sleeve 5,05 spacer sleeve 6,06 spacer sleeve 7,07 spacer sleeve 8,01 protective plate 699 A hexagon-head bolt
clamping pin S 10 X 20 N N N N N 7 hexagon-head bolt M 10 X 25 lock ring A 10 hexagon-head bolt M 12 X 50 hexagon-head bolt M 12 X 95 washer A 13

308-00

Pos Part Number Description replacement transmission final-drive housing automatic transmission - > 038 - > 038 C - > 038 A N 051 H 127 E replacement transmission replacement transmission replacement transmission final-drive housing final-drive housing breather pipe cap screw plug M 24 X 1,5 round seal round seal lid sealing ring radial shaft seal lock ring A 10 hexagon-head bolt M 10 X 30 radial shaft seal needle-roller bearing round seal adjusting ring radial shaft seal flanged shaft flanged shaft screw screw tab washer /L /R /L /R
RCA RH RCD RCB RH RCA RCB RCD

5 * 549 B 6 * 623 A

8 * 637 A 9 * 529 B N 1

133 C 139

14 * 173
16 * 399 B 17 (17) 18 (18) 409 257

Pos 22 N N

Part Number 5

Remark Qty 2 Model

Description spring washer B 6
13 hexagon-head bolt M 6 X 15 dowel sleeve

309-00

Pos Part Number Description transmission case automatic transmission 2A 5 5A G N N transmission case stud AM 8A X 56 stud AM 10A X 38 screw plug M 10 X 1 lever parking lock torsion spring bolt engaging lever parking lock lock washer lock washer operating rod shaft circlip A 10 X 1 lever for cable control spring washer B 6 hexagon-head bolt M 6 X 3,5 round seal 14 X 2,5 locking segment washer A 16 spring washer B 16 hexagon nut M 16 X 1,5
133 A 117 B 121 A N N 438 1

153 A 209 C N 1

171 C N N 2

15 * N 18 19

193 B 179 N N 164 2

Pos 19A 20

Pos 41 N * 47 N N pan-head screw AM 5 X 15 round seal 24,5 spring washer B 8 hexagon nut M 383 B Part Number 307 N 5 clip spring washer B 6 hexagon-head bolt M 6 X 12 oil pan gasket lock ring A 8 hexagon-head bolt M 8 X 20 intermediate plate gasket Description

pipe G RCA 3>> G RCB 3>>
piston G G >>RCA 3 >>RCB 3
piston G RCA 3>> G RCB 3>>

62 62A 67 68

553 A A 557 A 345 C 346 C 571 J A 558
turbine shaft gasket oil pump shaft piston ring adjusting shim 0,40 adjusting shim 1,20 converter converter hexagon-head bolt wire ring

1 X RH RCA RCD RCB

310-05
Pos Part Number Description slide-valve gearbox regulator oil strainer automatic transmission P 037 C 037 H F N N slide-valve gearbox slide-valve gearbox slide-valve gearbox compression spring piston spring washer B 6 hexagon-head bolt M 6 X 30 oil strainer spring washer B 5 pan-head screw AM 5 X 15 regulator G G 9A 041 B regulator G RCA 3>> G RCB 3>> governor shaft G G 11 * 371 round seal lid G G 12A 371 A lid G RCA 3>> G RCB 3>> >>RCA 3 >>RCB 3 >>RCA 3 >>RCB 3 >>RCA 3 >>RCB 3

RH RCA RCB RCD

421 A N 4

Pos N N N

Part Number 228 3
Description oval-head screw M 5 X 40 spring washer B 8
16 hexagon-head bolt 8 X 20 gasket lid manual valve

311-00

Pos Part Number Description differential automatic transmission 1 * 081 A repair kit for differential axle nut lid differential housing ring gear and pinion shaft 12:143 J 135 A 185 C 641 D 641 E 641 F 641 G 641 H 641 J 641 K 641 L 641 M 641 N ring gear and pinion shaft 11:38 hexagon-head bolt M 10 X 1 X 24 taper roller bearing adjusting shim 1,10 adjusting shim 1,125 adjusting shim 1,15 adjusting shim 1,175 adjusting shim 1,20 adjusting shim 1,225 adjusting shim 1,25 adjusting shim 1,275 adjusting shim 1,30 adjusting shim 1,325
1 X X X X X X X X X RCB RH RCA RCD
Remark Qty X X X X X X Model
Pos Part Number 641 AQ 641 AR 641 AS 641 AT 551 C 085 B 639 A 141 AE 141 AF 141 AG 141 AH 141 AJ 141 AK 141 AL 141 AM 141 AN 141 AP 141 AQ 141 AR 141 AS Description adjusting shim 1,825 adjusting shim 1,85 adjusting shim 1,875 adjusting shim 1,90 taper roller bearing radial shaft seal bush adjusting shim 1,10 adjusting shim 1,125 adjusting shim 1,15 adjusting shim 1,175 adjusting shim 1,20 adjusting shim 1,225 adjusting shim 1,25 adjusting shim 1,275 adjusting shim 1,30 adjusting shim 1,325 adjusting shim 1,35 adjusting shim 1,375 adjusting shim 1,40
Remark Qty X X X X X X X X X X X X X X X X Model
Description adjusting shim 1,35 adjusting shim 1,375 adjusting shim 1,40 adjusting shim 1,425 adjusting shim 1,45
641 P 641 Q 641 R 641 S 641 T
641 AA adjusting shim 1,AB adjusting shim 1,AC adjusting shim 1,AD adjusting shim 1,AE adjusting shim 1,AF adjusting shim 1,AG adjusting shim 1,AH adjusting shim 1,AJ adjusting shim 1,AK adjusting shim 1,AL adjusting shim 1,AM adjusting shim 1,AN adjusting shim 1,AP adjusting shim 1,80

911 00

repair kit for clutch comprising: pressure plate clutch plate clutch release bearing

401-00

Pos Part Number Description wishbone cross member 1 (1) 153 D 365 G N N N 3 cross member cross member wishbone ball joint $ 17 MM lock ring A 7 hexagon nut M 7 hexagon-head bolt M 7 X 20 rubber mounting washer A 13 hexagon-head bolt M 12 X 1,5 X 100 lock nut M 12 X 1,5 rubber mounting clip washer hexagon-head bolt M 10 X 65 hexagon-head bolt M 12 X 75 washer washer hexagon-head bolt M 10 X 45 lock nut M 10 heat protection plate heat protection plate

/LL /RL

182 D N 1

181 A N N 183 1

N N 130 2

108 02

/LL /LL

-84 85-

Pos (19) (19) 20 21
Remark /RL /RL -84 85Qty Model
heat protection plate heat protection plate N N 7 washer A 6

401-05

Pos Part Number Description steering knuckle 1 (1) 10 (10) L 312 L 065 B C 692 C steering knuckle steering knuckle front wheel hub wheel bolt radial sealing ring taper roller bearing taper roller bearing thrust washer clamping nut pan-head screw cap cap lock washer /L /R /L /R

402-00

Pos Part Number Description suspension shock absorber front Q coil spring 1 set identification blue vibration damper - koni vibration damper - koni vibration damper - koni vibration damper - koni vibration damper insert - koni union nut boot rubber stop concave washer spacer sleeve suspension strut mounting bearing flange spring washer B 12 hexagon nut M 8 sealing ring stop ring stop lock nut VM 14 X 1,5 eccentric screw /L /R /L /R

(2) 3 (3) 00

2 M474 M474 M474

13 (14) 17 18

303 C 345 N N 008 8

147 N 1

hexagon-head bolt M 12 X 1,5 X 00 eccentric washer N 4 lock nut VM 12 X 1,5

402-05

Pos Part Number stabiliser (1) 4 (4) (4) 5 (5) G 053 N 053 J 314 A stabiliser $ 20 MM stabiliser $ 21,5 MM stabiliser $ 23 MM suspension clip rubber bush $ 20 MM rubber bush $ 21,5 MM rubber bush $ 23 MM bearing bracket bearing bracket rubber bush hexagon-head bolt M 8 X 22 lock nut VM 8 /L /R Description

-2 -M404 M404 M404 M404

403-00
Pos Part Number Description steering gear tie rod 1 (1) (7) 8 (8) (10) C 832 C 02 N 6 steering gear steering gear cap stopper boot boot terminal $ 45 MM clip clip rubber insert rubber insert washer A 8,4 hexagon-head bolt M 8 X 60 hexagon-head bolt M 8 X 45 tie rod F F >>94DN>>94DN/L /R

104 00

115 00

115 90

020 41

020 93

020 42

020 94

Pos (7) (7) 7 (7) (7) (7) (7)
Pos 8 Part Number Description emergency wheel alloy wheel with collapsible tire support hexagon-head bolt M 10 X 18 lock ring wing screw M 10 X 75 washer small electric compressor tyre pressure gauge wheel nut 1 set lockable wheel nut lockable without lock cap blank key for wheel nut lockable
hub cap hub cap grand prix white hub cap platinum-metallic hub cap white gold metallic wheel nut rubber valve $ 15,00 valve support balance stick-on weight 10 G balance stick-on weight 20 G balance stick-on weight 30 G balance stick-on weight 40 G balance stick-on weight 50 G balance stick-on weight 60 G balance stick-on weight 70 G balance stick-on weight 80 G disc wheel for winter use
4 X X X X X X X X 16B 16A (14) (12)

191 N 2

312 01
7A U perforated disc wheel steel 5 1/2 J X 15 7B 7C N 1 ball seat nut

hub cap emergency wheel

602-00
Pos Part Number disc brake front axle (8) (8) (8) (12) 13 (13) N N cover plate spring washer B 7 hexagon-head bolt M 7 X 10 brake disc hexagon-head bolt M 8 X 22 spring washer B 8 hexagon nut M 8 floating calliper floating calliper floating calliper floating calliper spring washer B 12 hexagon-head bolt M 12 X 1,5 X 40 guide spring ventilation valve ventilation valve dust boot dust boot expanding spring retaining pin retaining spring safety seal brake pad repair set without asbestos /L /R /L /R Description

10 -83 --83 84-4 -2 1

083 A N 1

959 00

14 * 15 * 16 * 112 (16) 02

Pos 20 -

mounting parts gasket set warning contact cable holder clip

603-00

Pos Part Number disc brake rear axle 3 (3) 4 4A 4B N 1 brake disc countersunk-head screw M 6 X 12 floating calliper floating calliper brake pad repair set without asbestos mounting parts warning contact cable holder expanding spring retaining pin retaining spring safety seal gasket set ventilation valve dust boot guide spring guide spring guide spring guide spring hexagon-head bolt M 12 X 1,5 X 37 spring washer B 12 handbrake 14 A repair kit without asbestos /L /R /L /R /L /R Description

--83 -4

705 00
5 * 6 * 7 (7) (11) (11) (11) 014 02

Pos (14)

repair kit 1 set only together with compression spring 996.352.741.00 adjusting screw 993.352.071.02 compression spring compression spring only together with repair kit 997.352.993.00 support bush adjusting screw return spring return spring expanding bow 459 N bolt

AUT. AUT. AUT.

309 N N N 1

315 D 02

Pos 35 36

Remark Qty * Model

hose 12,5 X 7,A 220 MM clutch hose
clutch pipeline bush washer A 8,4 N N N N 01 lock washer 01 washer clamp hexagon-head bolt M 5 X 20
support N N N N hexagon-head bolt M 5 X 12 spring washer B 5
14 hexagon nut M hexagon-head bolt M 8 X 18

washer 255 washer

702-05
Pos Part Number Description pedals right-hand drive 1 (1) 4 (4) 153 A 353 A 213 N N N 1 brake pedal brake pedal bearing sleeve bearing sleeve cap cap return spring clutch power spring clevis hexagon nut M 10 lock bolt 8 X 32 clutch pedal bracket hexagon nut M 8 spring washer A 8 clutch master cylinder bellows intermediate piece hexagon nut BM 8 bush washer A 10,5 lock gasket

AUT. AUT.

315 A 113 A N 3

191 00

Pos 25 (25) 31A 32 (32) 37 (37) 38 N

Remark Qty 2 -1 -Model

Description spring washer A 8
hexagon nut M connecting hose F >>94DN4 00050
hose F 94DN4 00051>> expansion tank 381 B N 5 strainer lid spacer sleeve spring washer B 6
hexagon-head bolt M 6 X 02 hexagon nut M 01 clutch tube clutch tube 189 clutch hose
bush washer A 8,4 N 01 lock washer

support support clip

702-10
Pos Part Number Description accelerator pedal accelerator cable for cars with manual transmission 1 (1) (1) 2 (2) A 40 N N accelerator control accelerator control accelerator control accelerator cable accelerator cable accelerator pedal hexagon nut M 6 washer washer lock washer circlip bearing sleeve buffer cable clip spring adjusting screw

/LL /RL /LL /LL /RL

1 M454

731 00

702-15
Pos Part Number Description accelerator pedal accelerator cable for cars with automatic transmission 3 (3) 4 (4) N 1 accelerator control accelerator control accelerator cable accelerator cable cable cable circlip accelerator pedal hexagon nut M 6 washer bearing sleeve lock washer washer buffer nipple nipple sealing sleeve tension spring support spring hose clamp support retaining bracket cable clip clamp hose holder

/LL /RL /LL /RL /LL /RL

511 A N 2

269 A 563 C A 40

Pos 25 26
hose holder adjusting screw

801-00

Pos Part Number Description body in white prime coated sealed with underbody protection bodyshells can only only available from current model year available 1 (1) (1) (1) body in white body in white body in white body in white

N N N 7

00 N 1

Pos 26 (26) 29 30
Remark Qty /L /R M058 M058 M058 M058 M058 M058 Model
Pos 38 N Part Number 8 washer 4,3 Description
washer B 4,3 N N hexagon nut tapping screw B 5,5 X 32
spacer rubber N 01 special nut
support number plate N N N 3 plate plate washer 7 lock ring B 6 hexagon-head bolt M 6 X 40
stopper towing lug see group 0/01/00 N 7 washer A 13 F lock ring B 12 F /H >>94EN/H >>94EN/H
hexagon-head bolt M 12 X 65 F >>94EN4 03821
eccentric washer F 94EN4 03822>> N 02 pan-head screw M 12 X 1,5 X 65 F 94EN4 03822>>
special nut tapping screw BZ 4,2 X 9,5

802-10

Pos Part Number Description front spoiler 03 front spoiler up to model 84 use also: POS.36-42 front spoiler for fog lamp up to model 84 use also: POS.36-42 attachment strip hexagon-head bolt M6 X 12 spacer lock nut M 6 bracket hexagon-head bolt M6 X 12 spacer hexagon-head bolt M6 X 12 washer A 6,4 lock nut M 6 cover hexagon-head bolt M6 X 16 washer A 6,4 nut M 6 combination screw B6,3 X 19 speed nut B6,3 X 17 retaining bracket /L /R

371 05

419 00

Pos 41

Remark Qty 5 Model
Pos 42 Part Number speed nut M 6 Description
sealing rubber sealing rubber sealing rubber sealing rubber attachment strip N N 13 hexagon-head bolt M6 X washer A 6,4
lock nut M 6 N 13 hexagon-head bolt M6 X 15
spacer lock nut M 00 support F 94DN4 08353>> N 13 hexagon-head bolt M 6 X 15
lock nut M 6 N 7 washer A 6,4
retaining bracket spacer air duct attachment strip spacer lock nut M 01 spacer N 13 hexagon-head bolt M 6 X 15

803-00

Pos Part Number lid front actuator lid lock 3 (3) N 16 lid filler piece hinge hinge hexagon-head bolt M 8 X 20 lock ring B 8 washer A 8,4 bearing pin bearing pin spring washer B 10 washer hood stay rubber mounting support guide piece lock upper part lid lock hexagon-head bolt M 6 X 12 washer lid lock lower part hexagon-head bolt M 4 X 8 lock ring B 4 /L /R Description

8 -84 85-2 -4

00 N 6

363 A 02 N 2

Pos (39) N

Part Number 6

Pos Part Number 70B 02 70B black cup black countersunk-head screw M 6 X 15 M 6 X tab washer tapping screw BZ 4,2 X 13 washer BZ 4,3 X 9 prestole cage B 4,8 mount lid-release cable Description
Description hexagon nut M 4 lid lock cable clamping washer clamping piece

531 A N 1

KZ8 brown F 94DN4 03822>>

DF9 black F

Pos Part Number KZ9 /RL/L 1 (1A) 011 N Description brown/grey-beige F 94DN4 03822>> door trim panel power windows electrically adjustable leatherette brown F >>94DN4 03821
FE6 brown/ beige/brown (1) 011 K door trim panel leatherette/ checker board velour
FE5 black/ grey/black FE6 brown/ beige/brown (1) 012 K door trim panel F >>94CNF >>94DNleatherette/ checker board velour /RL/R (J) 1

DG1 JS3 KZ8 KZ9 1A 012 N

brown/grey-beige F >>94DNbrown F 94DN4 03822>> brown/grey-beige F 94DN4 03822>> door trim panel power windows electrically adjustable F 94DN4 00111>> F 94DN4 00109>> leatherette brown F >>94DN/RL/R 1
FE5 black/ grey/black FE6 brown/ beige/brown (1A) 011 R door trim panel power windows electrically adjustable leatherette >>94DN/LL/L 1
DG1 JS3 KZ8 KZ9 (1A) /LL/R 1 JS1 1A 012 R 011 R

DG1 brown F

brown/grey-beige F >>94DNbrown F 94DN4 03822>> brown/grey-beige F 94DN4 03822>> door trim panel leatherette/ checker board velour brown/ brown-grey door trim panel leatherette/ checker board velour brown/ brown-grey door trim panel leatherette/ checker board velour /RL/L 1 /LL/R 1 /LL/L 1
JS3 brown/grey-beige F >>94DNKZ8 brown F 94DN4 03822>> KZ9 brown/grey-beige F 94DN4 03822>> 1A 012 R door trim panel power windows electrically adjustable leatherette >>94DN4 03821
JS3 brown/grey-beige F >>94DNKZ8 brown F 94DN4 03822>> (1A)
Pos (1A) /RL/R (J) 1 DF9 KZ7 Part Number 011 N Description door trim panel power windows electrically adjustable leatherette black F >>94DN4 03821

Remark /LL/L Qty 1 Model

JS1 brown/ brown-grey 1A 012 N door trim panel F 94DN4 00111>> F 94DN4 00109>> leatherette/ checker board velour
JS1 brown/ brown-grey 1A (1A) 011 R door trim panel leatherette/ pin stripe velour /LL/L N
black F 94DN4 03822>> door trim panel power windows electrically adjustable leatherette black F >>94DN/LL/R 1
JS5 brown/ brown-beige JS2 brown/ grey-beige-white 1A 012 R door trim panel leatherette/ pin stripe velour /LL/R 1 (1A)

DF9 KZM

black F 94DN4 03822>> door trim panel power windows electrically adjustable leatherette black F >>94DN/RL/L 1
JS5 brown/ brown-beige JS2 brown/ grey-beige-white (1A) 011 N door trim panel leatherette/ pin stripe velour /RL/L 1 1A
black F 94DN4 03822>> door trim panel power windows electrically adjustable F 94DN4 00111>> F 94DN4 00109>> leatherette black F >>94DN/RL/R 1
JS5 brown/ brown-beige JS2 brown/ grey-beige-white 1A 012 N door trim panel F 94DN4 00111>> F 94DN4 00109>> leatherette/ pin stripe velour /RL/R (J) (1A) 011 N 1 KZ7 DF9

(6) A seat side bolster cover left seat leatherette/ seat surface pin stripe velour PL8 black/ black-red QE5 black/ black-white (6) A seat side bolster cover right seat leatherette/ seat surface pin stripe velour PL8 black/ black-red QE5 black/ black-white (6) A seat side bolster cover right seat leatherette/ seat surface pin stripe velour PL8 black/ black-red QE5 black/ black-white 6A A seat side bolster cover left seat leatherette LR6 black LR7 brown LR8 grey-beige PX1 black PX3 brown QD8 grey-beige (6A) A seat side bolster cover left seat leatherette LR6 black

LR6 LR7 LRPX1 PX3

QD8 6A A 631 50

1AJ 2NF

85 3NG /R 1 6FL 84
Pos Part Number Description seat side bolster cover right seat leather black F beige brown F grey-beige F >>94DN>>94DN>>94DN/R
KZ2 black F 94DN4 03822>> KZ5 brown F 94DN4 03822>> KZ4 grey-beige F 94DN4 03822>> (6A) A seat side bolster cover left seat leather 1AJ black F 2NF beige 3NG brown F 6FL grey-beige F >>94DN>>94DN/R 1

(6A) A 634 50

1AJ 2NF 3NG 6FL KZ2 -6.82 KZ5 KZ4
black F 94DN4 03822>> brown F 94DN4 03822>> grey-beige F 94DN4 03822>>
KZ2 black F 94DN4 03822>> KZ5 brown F 94DN4 03822>> KZ4 grey-beige F 94DN4 03822>> (6A) A seat side bolster cover right seat leather 1AJ black F 2NF beige 3NG brown F 6FL grey-beige F >>94DN>>94DN>>94DN-6.82 /L 1
KZ2 black F 94DN4 03822>> KZ5 brown F 94DN4 03822>> KZ4 grey-beige F 94DN4 03822>>

808-20

Pos Part Number back seat complete single parts see group 8/08/045 C backrest leatherette/ centre part pin stripe velour black/ black-white F brown/ brown-beige F beige/ brown-beige grey-beige/ grey-beige-white F >>94DNblack/ black-white F 94DN4 03822>> brown/ brown-beige F 94DN4 03822>> grey-beige/ grey-beige-white F 94DN4 03822>> backrest leatherette/ centre part checker board velour black/ grey/black brown/ beige/brown beige/ beige/brown black/ light grey-black F >>94DNDescription

FD8 FD9 FE1 JR4

Pos Part Number JN5 Description grey-beige F 94DN4 03822>> backrest leatherette/ centre part pin stripe velour black/ black-white brown/ brown-beige grey-beige/ grey-beige-white backrest leatherette/ centre part checker board velour black/ light grey-black brown/ brown-grey grey-beige/ brown-grey backrest leatherette/ centre part porsche lettering cloth black/black brown/brown grey-beige/grey-beige black/black brown/brown grey-beige/grey-beige backrest leatherette/ backrest surface porsche lettering cloth black/black brown/brown
JR5 brown/ brown-grey F JR6 grey-beige/ brown-grey F
>>94DN1 >>94DNJN1 JN00 841
LD5 black/ light grey-black F 94DN4 03822>> LD6 brown/ brown-grey F 94DN4 03822>> LD7 grey-beige/ brown-grey F 94DN4 03822>> 1A 045 C backrest leatherette/ backrest surface berber cloth 1 1

>>025

027 02

035 08

128 40

Part Number N 1

Description threaded piece tensioning sleeve desk pad guide tube centring washer lower centring washer upper compression spring pan-head screw M 5 X 40 mounting piece tapping screw 3,9 X 13 speed nut switch threaded bush knob wiring harness wiring harness bellows plug socket installation set door mirror electrically adjustable heatable plane comprising: mirror housing mirror base hexagon-head bolt M 5 X 10 covering frame with transmission mirror glass plane /LL/R

345 02

347 00

042 02

181 N 5

A >>026

Part Number 128 40
Description grommet for mirror glass reinforcement threaded piece tensioning sleeve desk pad guide tube centring washer lower centring washer upper compression spring pan-head screw M 5 X 40 mounting piece tapping screw 3,9 X 13 speed nut switch threaded bush knob wiring harness wiring harness bellows rocker switch plug socket 7-pole repair kit blind rivet comprising: blind rivet blind rivet blind rivet assembly sleeve set of moldings moulding comprising:

140 C N 1

1 M418
Part Number side guard wing side guard door side guard door

Description /V

133 00

134 00

141 00
side guard side section side guard side section use also: adhesive sealing compound air conditioner for subsequent installation use also: vacuum line F

142 00

AMV 05 >>901 00

1 /LL 1

099 00

1 >>94CN1

099 02
vacuum line F 94CN4 02412>> knee protection trim

412 05T 21S 1DB 4RB

1 -82 -82 8383-
black brown black brown when required order also:

196 CB

wiring harness for centre console relay relay relay relay wiring harness

A 253 B B

901-00
Pos Part Number Description engine electrics N N N N ignition coil protection cap washer A 5,3 washer A 6,4 lock ring B 5 lock ring B 6 hexagon nut M 5 hexagon nut M 6 washer A 8,4 pan-head screw M 8 X 12 distributor cap rotor comprising: POS. 12, 13, 26 rotor pan-head screw dust cover ignition coil plug ignition lead distributor plug ignition lead cylinder 1 ignition lead cylinder 2 ignition lead cylinder 3

/L (F)

408 00

410 00

/R (F)
Pos 21 (21) (21) (21) 22 (22) (22) 27 (27)
Pos 31 Part Number N 2 Description tapping screw B 3,9 X 19 spacer sleeve clip tapping screw BZ 4,2 X 45

Remark Qty 8 X Model

Description electric motor pop-up headlight protection cap lower protection cap upper

379 B 941 387

/L /L (F) /R /R (F) (J) (J) (F) 2 M492
lock nut hexagon-head bolt M 6 X 12 N 2 lock ring B 6 cap headlamp unit gasket high-beam headlight white

659 A D

additional headlamp yellow 752 D high-beam headlight white
additional headlamp yellow 771 B C 986 headlamp headlamp headlamp connector housing 3-pole plug with guide flat plug 6,3 X 0,8
bulb 12 V 45/50 W halogen bulb H 91 halogen bulb H 4

905-06

Pos Part Number Description fog headlamp (1) (1) 8 (8) (8) (8) N N fog headlamp white fog headlamp yellow fog headlamp white fog headlamp yellow bulb H 3 support washer A 5,3 tapping screw B 4,8 X 22 washer A 6,4 hexagon-head bolt M 6 X 12 lens white lens white lens yellow lens yellow gasket oval-head screw wiring harness /L /R /L /R /L /L /R /R

715 N 2

177 00

(CH) (N) (S)

905-10
Pos Part Number Description direction indicator light front 1 (1) 2 (2) N 1 direction indicator light direction indicator light lens lens oval-head screw oval-head screw M 4 X 10 bulb 12 V - 21 W gasket threaded plate oval-head screw M 4 X 20 line distributor protection cap for flat connector /L /R /L /R

971 921

905-15
Pos Part Number Description license plate light rear light 5 (5) 021 A 131 N 2 license plate light bulb 12 V - 4 W gasket tapping screw B 3,9 X 13 bulb holder bulb holder pin connector socket 7-pole bulb 12 V - 5 W bulb 12 V - 21 W lock ring B 5 spring washer A 5 hexagon nut M 5 sealing cord 9 MM $ roller 10 M 1070 MM housing with lens housing with lens housing with lens for cars with rear fog light /L /L /R

90 N N N 14

172 00

Pos (13)

Description housing with lens for cars with rear fog light cap cap

945 285

905-20
Pos Part Number Description interior light direction indicator light 3 (3) 105 B 00 N 5 interior light luggage compartment lamp glove compartment light linolite lamp 12 V - 10 W bulb 12 V - 3W contact switch gasket tapping screw BZ 3,5 X 9,5 clip engine compartment lamp bulb 12 V - 10 W washer 4,3 oval-head sheetmetal screw B 4,2 X 9,5 line distributor plug with guide simple wiring harness direction indicator light bulb holder bulb direction indicator light

MM(USA)(CDN) 944 M220 (USA)(CDN) 944 M249 (USA)(CDN)(J)
016 J 016 J 087 M 016 K 016 K 087 N
85 F QK. 85 F 7Q. 85 F RCD. 85 F QM. 85 F 8Q. 85 F RCB.
5-SPEED 5-SPEED 3-SPEED 5-SPEED 5-SPEED 3-SPEED

944 (J) 944 M220

016 K 016 K 85 F QL. 85 F 4M.

5-SPEED 5-SPEED

EXPLANATION OF THE TRANSMISSION-NUMBERS USED IN THE CATALOGUE =============================================================

DIGIT:

R C D ===== ! !

=== ! ! ! !

=== ! ! ! ! ! !

2 = ! ! ! ! ! ! ! !

IDENTIFICATION LETTER---------------------+
MANUFACTURING DAY--------------------------------+
MANUFACTURING MONTH------------------------------------+
MANUFACTURING YEAR------------------------------------------+

ENGINE

ENGINE TYPE

ENGINE-NUMBER

TECHNICAL DATA

M44.01 M44.03

82 C 41C 0001>C 41C 5001>8000
4ZYL/2,5L/120KW 4ZYL/2,5L/120KW
M(USA)(CDN)(J) 944 M249 (USA)(CDN)(J)
M44.01 M44.03 M44.02 M44.04
83 D 41D 0001>ED 41D 5001>D 43D 0001>JD 43D 5001>9999
4ZYL/2,5L/120KW 4ZYL/2,5L/120KW 4ZYL/2,5L/110KW 4ZYL/2,5L/110KW
84 E 41E 00001>20000 4ZYL/2,5L/120KW 84 E 41E 20001>30000 4ZYL/2,5L/120KW 84 E 43E 00001>20000 4ZYL/2,5L/110KW 84 E 43E 20001>30000 4ZYL/2,5L/110KW
85 F 41F 40001>50000 4ZYL/2,5L/120KW 85 F 41F 50001>60000 4ZYL/2,5L/120KW 85 F 43F 40001>50000 4ZYL/2,5L/110KW 85 F 43F 50001>60000 4ZYL/2,5L/110KW
EXPLANATION OF THE MOTOR-NUMBERS USED IN THE CATALOGUE ======================================================

F = = = ! ! !

6 ========= ! ! ! ! ! ! !
ENGINE TYPE (4 = 4-CYL.-ENGINE)------------------+ ! ! ! ! ENGINE VERSION-------------------------------------+ ! ! MODEL YEAR-------------------------------------------+
SERIAL NUMBER------------------------------------------------+

FAHRZEUGTYP

FAHRZEUG-IDENT.NR MOTORTYP
82 C 94 CN40 0051>>

M44.01/03 120KW

(USA)(CDN) 944 (J)
83 C 94 DN40 0051>> 83 C 94 DN45 0051>> 83 C 94 DN40 0051>>