Volvo 900, S90

Manufacturer: Sachs Handel Axle: Rear axle Shock absorber type: Gas pressure Vehicle equipment: for vehicles without Ride height adjustment Quantity per car: 2 Volvo S90: all models

1015255

271911
Shock absorber Front axle Oil pressure
Manufacturer: Volvo Axle: Front axle Shock absorber type: Oil pressure Shock absorber design: Suspension strut Quantity per car: 2 Volvo S90, V90: all models recommend Accessories 1017813: Shock absorber Dust cover Kit

1004410

272220

Volvo 900, V90

Axle: Rear axle Shock absorber type: Gas pressure Vehicle equipment: for vehicles without Ride height adjustment Quantity per car: 2 Volvo V90: all models Caution! Extremely rare! Actually, many vehicles registered in Germany come with an automatic level control feature! A replacement for normal shocks without simultaneous change of the rear axle spring leads to an extreme rear sagging of the vehicle!

1004849

9173200

Shock absorber Rear axle

Manufacturer: Sachs Handel Axle: Rear axle Shock absorber system: Ride height adjustment, automatic Vehicle equipment: for vehicles with Ride height adjustment Quantity per car: 2 Volvo S90: all models

1004651

9173202
Manufacturer: Sachs Handel Axle: Rear axle Shock absorber system: Ride height adjustment, automatic Vehicle equipment: for vehicles with Ride height adjustment Quantity per car: 2 Volvo V90: all models

#G226#

Shock absorber Dust cover
1017813 Shock absorber Dust cover Kit
Axle: Front axle Quantity unit: Kit Volvo S90, V90: all models

#G237#

Suspension strut Support Bearing

1003677

1387188
Suspension strut Support Bearing upper
Fitting position: upper Quantity per car: 2 Volvo S90, V90: all models recommend Accessories 1021286: Supporting ring, Suspension strut bearing Front axle upper
Suspension + Steering > Shock absorbing > Suspension Strut Bearing >

#G772#

1021286

1273745

Supporting ring, Suspension strut bearing Front axle upper
Manufacturer: Volvo Axle: Front axle Fitting position: upper Quantity per car: 2 Volvo S90, V90: all models

#G239#

Control arm

1005578

274451

Control arm left

Axle: Front axle Fitting position: left Volvo S90, V90: all models recommend Accessories 1000910: Ball joint lower

1005579

274452

Control arm right

Axle: Front axle Fitting position: right Volvo S90, V90: all models recommend Accessories 1000910: Ball joint lower

#G238#

Ball joint

1000910

270477

Ball joint lower

Drive Train > Clutch >

1004193

272331
Manufacturer: Volvo Additional info: without Clutch releaser Volvo S90, V90: all models, engine B6304FS, gearbox M90 recommend Accessories 1004214: Release bearing

1004411

Additional info: without Clutch releaser Volvo S90, V90: all models, engine B6304FS, gearbox M90 recommend Accessories 1004214: Release bearing

#G478#

Pilot bearing, Clutch

1026426

3507190
Volvo 850, 900, C70 (-2005), S40 (-2004) V40, S70 V70 (-2000), S90 V90
Manufacturer: Volvo Guide bearing Type: Bearing bushing Volvo S90, V90: all models, gearbox all automatic transmission

#G255#

Release bearing

1004214

9163505
Manufacturer: Sachs Handel Volvo S90, V90: all models
Drive Train > Clutch Control > Clutch, mechanical parts > Releaser, Clutch >

#G257#

Release fork, Clutch

1007928

3549983
Manufacturer: Volvo Clutch operating mode : hydraulic Volvo S90, V90: all models, gearbox M90 recommend Accessories 1019214: Pivot pin, Clutch fork

#G1234#

Pivot pin, Clutch fork

1019214

3549638

Volvo 200, 900, S90 V90

Manufacturer: Volvo Volvo S90, V90: all models, gearbox M90

#G259#

Guide tube, Clutch releaser

1026428

3549714

throw out bearing

Manufacturer: Volvo Volvo S90, V90: all models, gearbox M90 recommend Accessories 1026429: Seal ring Socket, Clutch release bearing
Drive Train > Clutch Control > Clutch Hydraulics > Master Cylinder >

#G245#

Master cylinder, Clutch

1026314

8601785

1003936

8603309
Clutch operating mode : hydraulic Volvo S90, V90: all models recommend Accessories 1008087: Brake fluid 0,5l

#G246#

Repair kit, Clutch master cylinder
1020740 Repair kit, Clutch master cylinder
Volvo S90, V90: all models recommend Accessories 1008213: Paste, Brake/Clutch hydraulic parts 180ml

1003655

273929
Volvo S90, V90: all models recommend Accessories 1008087: Brake fluid 0,5l 1008213: Paste, Brake/Clutch hydraulic parts 180ml

discontinued

Drive Train > Clutch Control > Clutch Hydraulics > Slave Cylinder >

#G249#

Slave cylinder, Clutch

1003938

8601783
Volvo S90, V90: all models, engine B6254S Inner diameter is 22mm recommend Accessories 1008087: Brake fluid 0,5l

1015678

Main bearings, Crankshaft Standard Kit
Volvo 900, S80 (-2006), S90 V90, XC90
Oversize grade: Standard Quantity unit: Kit Volvo S90, V90: all models The bearing sets have been replaced several times. The current number is 30731541 and covers all 5 and 6 cylinder inline gasoline engines.
Engine > Engine Repair > Crankshaft >

#G950#

Flywheel bolt

1006011

1275375
Manufacturer: Volvo Transmission type: Automatic transmission Quantity per car: 10 Volvo S90, V90: all models

1026427

9454744
Volvo 850, 900, C70 (-2005), S70 V70 (-2000), S90 V90
Manufacturer: Volvo Quantity per car: 10 Volvo S90, V90: yearsmodel from 1995, engine B6254FS Volvo S90, V90: yearsmodel from 1995, engine B6304FS

#G345#

Inlet valve

1006179

1397641
Volvo 850, 900, C70 (-2005), S40 (-2004) V40, S70 V70 (-2000), S80 (-2006), S90 V90
Diameter Piston: 7mm Volvo S90, V90: all models Valve stem diameter: 7mm

1032493

Manufacturer: Volvo Diameter Piston: 7mm Volvo S90, V90: all models
Engine > Engine Repair > Valves, Parts >

#G346#

Exhaust valve

1006180

9471466
Volvo 850, 900, C70 (-2005), S40 (-2004) V40, S70 V70 (-2000), S80 (-2006), S90 V90, V70 XC (-2000)

#G106#

Seal, Valve stem

1000433

3517893
Volvo 700, 850, 900, C70 (-2005), S40 (-2004) V40, S70 V70 (-2000), S80 (-2006), S90 V90, V70 XC (-2000)
Type: Seal Position: Inlet-/Outlet-Valve Volvo S90, V90: all models

#G340#

Rocker/Tappet

1006513

9207830
Valve control: for vehicles with hydraulic Cam followers Volvo S90, V90: all models

1029888

Manufacturer: Volvo Valve control: for vehicles with hydraulic Cam followers Volvo S90, V90: all models
Engine > Engine Repair > Connecting Rod >

#G350#

Big end bearings
1017570 Big end bearings Standard Kit
Volvo 850, 900, C30, C70 (2006-), C70 (-2005), S40 (2004-) V50, S40 (-2004) V40, S60 (-2009), S70 V70 (-2000), S80 (2007-), S80 (-2006), S90 V90, V70 P26, XC70 (2001-2007), V70 XC (-2000), V70 XC70 (2008-), XC60, XC90
Oversize grade: Standard Quantity unit: Kit Volvo S90, V90: all models Not for the B5244T4 motor. Set for 6 cylinder motor, replaces alle 4 and 5 cylinder sets.

1029320

30731539

Big end bearings Kit

Engine > Fuel Mixture Formation > Injection System > Throttle Blade >

#G383#

Sensor, Throttle position

1007704

1336385
Volvo 400, 850, 900, C70 (-2005), S70 V70 (-2000), S90 V90, V70 XC (-2000)
Volvo S90, V90: all models For three pin connector.

#G635#

Gasket, Throttle housing

1011721

9135990
Manufacturer: Volvo Type: Gasket Position: Throttle housing Volvo S90, V90: all models

#G1625#

Vacuum cell, Cruise control

1010773

1273227
Engine > Fuel Mixture Formation > Injection System > Mass Airflow sensor, Airflow meter >

#G124#

Air mass sensor, Gasoline

1013211

9146483

maf mass air flow

Manufacturer: Bosch Fuel type: Petrol Part type: Remanufactured part Volvo S90, V90: all models

1017755

Fuel type: Petrol Volvo S90, V90: all models

#G312#

Air intake hose

1014453

9142004

#G374#

Control valve, Fuel pressure

1009900

3547653
Volvo S90, V90: all models, refer additional info Volvo 960: Alternative 2 S / V90: without a fuel return system Please check the Bosch-number.
Engine > Fuel Mixture Formation > Injection System > Injectors >

#G425#

Valve, Injection system

1023959

30611668
Volvo S40 (-2004) V40, S60 (-2009), S80 (-2006), S90 V90, V70 P26, V70 P26, XC70 (2001-2007), XC90
Manufacturer: Volvo Valve type: Solenoid valve Position: Ignition system, Air filter Volvo S90, V90: yearsmodel from 1998, Catalytic post combustion (Air pump) with post combustion

#G422#

Idle control valve, Air supply

1009892

9454745
Manufacturers name: 0280140542 Volvo S90, V90: all models

#G122#

Seal ring, Injector

1000202

Volvo 200, 300, 700, 850, 900, C70 (-2005), S60 (-2009), S70 V70 (-2000), S80 (-2006), S90 V90, V70 P26, V70 XC (-2000), XC70 (2001-2007), XC90
Type: O-ring Position: Injector Injection system: LH-Jetronic Volvo S90, V90: all models
Engine > Fuel Mixture Formation > Injection System > Lambda Sensor >

#G147#

1002621 Lambda sensor

universal ohne Classic

Number of circuits: 1 Volvo universal ohne Classic: all models Screw out defective Lambda sensor. Pinch off cable,. New sensor is clamped on the remaining harness.

1002622

Number of circuits: 2 Volvo universal ohne Classic: all models Screw out defective Lambda sensor. Pinch off cable,. New sensor is clamped on the remaining harness.

1016701

Fitting position: right Colour: red-white Registration type: not E-type checked Volvo V90: all models

1024960

9126960
Manufacturer: Hella Fitting position: left Volvo S90: all models

1006270

Combination taillight left with Indicator
Fitting position: left Light function: with Indicator Registration type: E-type checked Volvo S90: all models

1006271

9126961
Combination taillight right with Indicator
Fitting position: right Light function: with Indicator Registration type: E-type checked Volvo S90: all models

1003912

9159657
Manufacturer: Volvo Fitting position: left Colour: red-white Volvo V90: all models

1025977

9159660
Manufacturer: Volvo Fitting position: left Driver position: for right-hand drive vehicles Volvo V90: all models

1003913

9159661
Manufacturer: Volvo Fitting position: right Colour: red-white Volvo V90: all models

#G359#

Fog light

1006210

9171063

Fog light left

Manufacturer: Volvo Fitting position: left Volvo S90, V90: all models
Electrics > Lights > Auxiliary Lights >

1027651

Fitting position: left Volvo S90, V90: all models

1006211

9171064

Fog light right

1027650
Fitting position: right Volvo S90, V90: all models

#G167#

Seal, Licence plate light

1016768

9126894
gasket license plate licenseplate licence plate licenceplate registration plate registrationplate number plate
Volvo 850, 900, V70 (-2000), V70 XC (-2000), V90
Manufacturer: Volvo Quantity per car: 2 Volvo V90: all models

#S100#

Electrics > Lights > Number Plate, Clearance Lights >

#G169#

Lens, Licence plate light

1016767

9159343
license plate licenseplate licence plate licenceplate registration plate registrationplate number plate
Manufacturer: Volvo Quantity per car: 2 Volvo V90: all models recommend Accessories 1016768: Seal, Licence plate light

#G841#

Interior light

1016761

6846630

Interior light for Trunk

Volvo 200, 700, 900, V90
Manufacturer: Volvo Use: for Trunk Volvo V90: all models

Manufacturer: Volvo Position: Door panel Quantity per car: 12 Volvo S90, V90: all models

1023259

9158929
Clip, Panel Door panel red
Manufacturer: Volvo Position: Door panel Colour: red Quantity per car: 12 Volvo S90, V90: all models

#G316#

Bonnet

1004950

1355339

hood front lid

#G955#

Safety catch, Bonnet

1006477

1334954

#S132#
Body > Bootlid, Bonnet, Doors, Sunroof > Gas Springs >

#G1056#

Gas spring, Tailgate

1000947

9463056
Quantity per car: 2 Volvo V90: all models recommend Accessories 1002683: Anchorage, Gas spring 1002684: Anchorage, Gas spring

1016631

Manufacturer: Stabilus Quantity per car: 2 Volvo V90: all models recommend Accessories 1002683: Anchorage, Gas spring 1002684: Anchorage, Gas spring

Gas spring, Trunk lid

1003077

3526575

boot lid rear trunk luggage trunk
Vehicle equipment: for vehicles without Trunklid spoiler Quantity per car: 2 Volvo S90: all models

Gas spring, Bonnet

1004261

#S133#

#G707#

Anchorage, Gas spring

1002684

1316489

Manufacturer: Volvo Fastening type: Ball stud Quantity per car: 2 Volvo V90: all models Ball on the chassis to accomodate trunk torsion spring.

1002683

1355262

#G1164#

Spacer

1031635

1273900

Spacer Brake hose

Manufacturer: Volvo Position: Brake hose Quantity per car: 2 Volvo S90, V90: all models

#G314#

Buffer

1019967

1382135

rubberbuffer

Buffer Front lid
Volvo 200, 300, 400, 700, 850, 900, S90 V90
Manufacturer: Volvo Position: Front lid Quantity per car: 2 Volvo S90, V90: all models

#S134#

Body > Body parts > Front section >

#G1411#

Cover, Front section

1018677

1392930
for Head light type: with included Fog lights Volvo S90, V90: all models

#G1635#

Bracket, Front section

1025134

9126731

1025133

9126732

#G788#

Bushing, Wiper

1021045

1342040

gasket seal wipers

Manufacturer: Volvo Window cleaning: for Rear window Volvo V90: all models

1015113 Tankadapter, Gas plant
Country code: Germany Thread size: M22 Volvo universal ohne Classic: all models

1015114

Country code: Portugal Country code: Austria Country code: Norway Country code: Hungary Country code: Greece Country code: France Country code: Italy Country code: Denmark Thread size: M22 Volvo universal ohne Classic: all models

1016748

Country code: Spain Country code: Norway Country code: United Kingdom Country code: Netherlands Thread size: M22 Volvo universal ohne Classic: all models

1016749

Country code: Germany Thread size: M10 Volvo universal ohne Classic: all models

#S139#

1016750
Country code: United Kingdom Country code: Norway Country code: Netherlands Thread size: M10 Volvo universal ohne Classic: all models

#G1292#

Steel Strap, fuel tank

1019687

3501484

Radiator grill

1002091

9126997

grille
Volvo S90, V90: all models Without a brace and without an emblem. recommend Accessories 1025133: Bracket, Front section 1025134: Bracket, Front section 1025336: Trim moulding, Radiator grill 1025337: Trim moulding, Radiator grill 1025338: Trim moulding, Radiator grill

1005063

Manufacturer: Volvo Volvo S90, V90: all models recommend Accessories 1025133: Bracket, Front section 1025134: Bracket, Front section

#S140#

Body > Body parts > Radiator grill >

#G666#

Clip, Radiator grill

1014258

1358491

1020029

968039
Volvo 700, 900, C70 (-2005), S40 (-2004) V40, S70 V70 (-2000), S90 V90
Manufacturer: Volvo Position: Radiator grill strut Fastening type: Spring lock nut Volvo S90, V90: all models

#G1402#

Mounting bracket, Starter

1023783

9442201
Volvo 850, 900, C70 (-2005), S60 (-2009), S70 V70 (-2000), S80 (-2006), S90 V90, V70 P26, XC70 (2001-2007)
Manufacturer: Volvo fits Part No.: 1001736 Volvo S90, V90: all models For 180 mm long starter

Spoiler

1005957 Spoiler Bumper front
Position: Bumper Fitting position: front Volvo S90, V90: all models

#S141#

Body > Body parts > Bumpers >

Mounting bracket, Bumper

1013613

9154992

Mounting bracket, Bumper front left
Manufacturer: Volvo Position: Fender Fitting position: front left Volvo S90, V90: all models

1027425

9154993
Mounting bracket, Bumper front right
Manufacturer: Volvo Position: Fender Fitting position: front right Volvo S90, V90: all models

#G852#

Clip, Spoiler mounting

1028076

1391884
Manufacturer: Volvo Position: Bumper Fitting position: front Quantity per car: 10 Volvo S90, V90: all models

#G513#

Engine protection plate

1000264

9447727
Volvo S90, V90: all models recommend Accessories 1019969: Tapping screw with Collar Outer hexagon 6 mm 1019970: Washer 1020252: Screw/Bolt with Collar M8 1020258: Washer

#S142#

Body > Body parts > Panelling >

#G859#

Cip, Rocker panel

1005993

9133417
Volvo 850, 900, S40 (2004-) V50, S60 (-2009), S70 V70 (-2000), S80 (-2006), S90 V90, V70 P26, V70 XC (-2000), XC70 (2001-2007), XC90

#G1741#

Screw, Engine cover

1022334

986009
Volvo 900, C30, C70 (2006-), C70 (-2005), S60 (-2009), S70 V70 (-2000), S80 (2007-), S80 (-2006), S90 V90, V70 P26, XC70 (2001-2007), V70 XC70 (2008-), XC90
Manufacturer: Volvo Thread size: M6 Length: 11,5mm Volvo S90, V90: all models

#G540#

Emblem

1025947

9183370

badges

Emblem C-pillar
Manufacturer: Volvo Position: C-pillar Quantity per car: 2 Volvo S90: all models Executive version

#S143#

Body > Body parts > Trim Parts > Protection Strips >

#G535#

Trim moulding, Radiator grill

1025338

9126361

molding grille

Manufacturer: Volvo Fitting position: lower Volvo S90, V90: all models

1025337

9126763
Manufacturer: Volvo Fitting position: upper Volvo S90, V90: all models

1025336

9126764

#G1106#

Trim moulding, Wheel arch

1016319

molding
Surface: chromed Quantity unit: Kit Volvo S90, V90: all models

#G211#

Wiper arm, Windscreen washer

1015269

9159485
Wiper arm, Windscreen washer for Rear window
Manufacturer: Volvo Window cleaning: for Rear window Volvo V90: all models recommend Accessories 1006370: Wiper blade for Rear window 1021045: Bushing, Wiper 1021840: Cap, Wiper arm

#G779#

Cap, Wiper arm

1021840

9154343

#G209#

Wiper motor

1012210

1358011
Wiper motor for Rear window
Window cleaning: for Rear window Volvo V90: all models

#S149#

#G1610#

Linkage, Wiper mechanism

1021757

1358012

#G210#
Water pump, Window cleaning

1014255

9178094

Volvo 900, S90 V90, V90

Volvo S90, V90: all models, Window cleaning for Windscreen Volvo V90: all models, Window cleaning for Rear window

#G213#

Water tank, Window cleaning

1022039

1342543

Volvo 700, 900, S90

Manufacturer: Volvo Contents: 3,2l Volvo S90: all models recommend Accessories 1013532: Cap, Water reservoir

1022040

1342958
Manufacturer: Volvo Fitting position: right Contents: 4,2l Volvo S90, V90: all models recommend Accessories 1013532: Cap, Water reservoir

#S150#

1022042

1369858

Manufacturer: Volvo Fitting position: left Contents: 4,2l Volvo S90, V90: all models recommend Accessories 1013532: Cap, Water reservoir

#G214#

Nozzle, Windscreen washer

1009119

1369855

1003992

9151799
Nozzle, Windscreen washer left
Window cleaning: for Windscreen Fitting position: left Volvo S90, V90: all models

1003991

9151800
Nozzle, Windscreen washer right
Window cleaning: for Windscreen Fitting position: right Volvo S90, V90: all models

#S151#

#G1112#

Cap, Water reservoir

1013532

3518883

#G678#

Valve, Window cleaning

1006978

1392074

Volvo 700, 850, 900, S40 (-2004) V40, S90 V90
Shape: T-piece Volvo S90, V90: all models

1022043

Manufacturer: Volvo Material: Mild steel Rim Size: 16Inch Rim Width: 6,5Inch Quantity per car: 4 Volvo S90, V90: all models recommend Accessories 1020941: Brush for Rim cleaning

#G699#

Wheel cover

1009006

274561

wheel cap

Wheel cover 15Inch Kit
Volvo 700, 850, 900, S40 (-2004) V40, S60 (-2009), S70 V70 (-2000), S80 (-2006), S90 V90, V70 P26, V70 XC (-2000), XC70 (2001-2007)
Manufacturer: Volvo Rim Size: 15Inch Quantity unit: Kit Volvo S90, V90: all models

1018510

31201866

Wheel cover 16Inch

Volvo C70 (-2005), S60 (-2009), S70 V70 (-2000), S80 (-2006), S90 V90, V70 P26, V70 XC (-2000), XC70 (2001 -2007)
Manufacturer: Volvo Rim Size: 16Inch Quantity per car: 4 Volvo S90, V90: all models

#S163#

Body > Carrier Equipment > Towbar, parts >

#G353#

Trailer hitch

1002412

3529305
Trailer hitch with rigid Coupling ball 1600kg
Manufacturer: Volvo Trailer hitch: with rigid Coupling ball Towed Weight: 1600kg Volvo S90, V90: all models When seeking a weight increase to 1800kg or rather 1900kg tensile load, the reinforcing kit (Skandix #1015479) must be installed. Basically the tension load given in the vehicle`s papers is the maximum amount. If you plan on increasing the tension load please contact TUV before(if applicable). recommend Accessories 1015408: Electric kit, Towbar 13terminal 1015479: Reinforcing kit, Trailer hitch

1002414

8698896
Trailer hitch with removable Coupling ball 1600kg
Manufacturer: Volvo Trailer hitch: with removable Coupling ball Towed Weight: 1600kg Volvo S90, V90: all models When seeking a weight increase to 1800kg or rather 1900kg tensile load, the reinforcing kit (Skandix #1015479) must be installed. Basically the tension load given in the vehicle`s papers is the maximum amount. If you plan on increasing the tension load please contact TUV before(if applicable). recommend Accessories 1015408: Electric kit, Towbar 13terminal 1015479: Reinforcing kit, Trailer hitch

#G995#

Reinforcing kit, Trailer hitch

1015479

6820174
Volvo S90, V90: all models This reinforcement kit must be additionally installed, if a weight increase to 1800 or 1900 Kg towing capacity is to be achieved.

#S164#

#G354#

Electric kit, Towbar

1015408

8682273

Electric kit, Towbar 13terminal
Manufacturer: Volvo Number of Poles: 13terminal Volvo S90, V90: all models

1016645

9134962
Electric kit, Towbar 7terminal
Manufacturer: Volvo Number of Poles: 7terminal Volvo S90, V90: all models

#G355#

Socket adapter
1010352 Socket adapter from 13 to 7 poles
Trailer hitch: from 13 to 7 poles

1010353

1028420

9437173

Paint 126 Spraycan 150ml

Manufacturer: Volvo Colour code: 126 Package type: Spraycan Contents: 150ml

1028421

9437174

Paint 127 Spraycan 150ml

Manufacturer: Volvo Colour code: 127 Package type: Spraycan Contents: 150ml

#S179#

1028422

9437175

Paint 128 Spraycan 150ml
Manufacturer: Volvo Colour code: 128 Package type: Spraycan Contents: 150ml

1028423

9437176

Paint 129 Spraycan 150ml

Manufacturer: Volvo Colour code: 129 Package type: Spraycan Contents: 150ml

1028205

9437177
Paint 130 silver Transparent Spraycan 150ml Kit
Manufacturer: Volvo Paint: 1-Component Paint Colour code: 130 Colour: silver Colour: Transparent Package type: Spraycan Contents: 150ml Use: universal paint Quantity unit: Kit Volvo S90, V90: all models

1028432

9437184

Paint 138 Spraycan 150ml

Manufacturer: Volvo Colour code: 138 Package type: Spraycan Contents: 150ml

#S180#

1028433

9437185

Paint 139 Spraycan 150ml
Manufacturer: Volvo Colour code: 139 Package type: Spraycan Contents: 150ml

1028434

9437186

Paint 140 Spraycan 150ml

Manufacturer: Volvo Colour code: 140 Package type: Spraycan Contents: 150ml

1028229

9437208
Paint 189 white Spraycan 150ml
Manufacturer: Volvo Paint: 1-Component Paint Colour code: 189 Colour: white Package type: Spraycan Contents: 150ml Use: universal paint Volvo S90, V90: all models

1028369

9437214
Paint 198/238 Spraycan 150ml
Manufacturer: Volvo Colour code: 198/238 Package type: Spraycan Contents: 150ml

#S181#

1028206

9437223

Paint 214 grey Transparent Spraycan 150ml Kit
Manufacturer: Volvo Paint: 1-Component Paint Colour code: 214 Colour: grey Colour: Transparent Package type: Spraycan Contents: 150ml Use: universal paint Quantity unit: Kit Volvo S90, V90: all models

1028371

9437236

Paint 239 Spraycan 150ml

Manufacturer: Volvo Colour code: 239 Package type: Spraycan Contents: 150ml

1028372

9437237

Paint 240 Spraycan 150ml

Manufacturer: Volvo Colour code: 240 Package type: Spraycan Contents: 150ml

1028373

9437238

Paint 241 Spraycan 150ml

Manufacturer: Volvo Colour code: 241 Package type: Spraycan Contents: 150ml

#S182#

1028374

9437239

Paint 243 Spraycan 150ml
Manufacturer: Volvo Colour code: 243 Package type: Spraycan Contents: 150ml

1027686

985387
Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M10 Length: 55mm

#S215#

1022492

985421

1021411

985456

Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M8 Length: 75mm

1028092

985492

1019965

986197
Screw/Bolt Flat head Inner-torx M5
Manufacturer: Volvo Bolt/Nut version: Flat head Bolt head-/Nut profile: Inner-torx Thread size: M5 Length: 10mm

#S216#

1029194

986200

Manufacturer: Volvo Bolt/Nut version: Flat head Bolt head-/Nut profile: Inner-torx Thread size: M5 Length: 16mm

1030243

986214
Screw/Bolt Flat head Inner-torx M6
Manufacturer: Volvo Bolt/Nut version: Flat head Bolt head-/Nut profile: Inner-torx Thread size: M6 Length: 16mm

1030249

986217
Manufacturer: Volvo Bolt/Nut version: Flat head Bolt head-/Nut profile: Inner-torx Thread size: M6 Length: 30mm

1025870

986291
Screw/Bolt Countersunk head Inner-torx M6
Manufacturer: Volvo Bolt/Nut version: Countersunk head Bolt head-/Nut profile: Inner-torx Thread size: M6 Length: 16mm

#S217#

1029191

986294

Manufacturer: Volvo Bolt/Nut version: Countersunk head Bolt head-/Nut profile: Inner-torx Thread size: M6 Length: 30mm

1020257

986985
Bolt/Nut version: without Collar Bolt head-/Nut profile: Outer hexagon Thread size: M8 Length: 20mm

1023110

988177
Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M8 Length: 22mm

1027807

988182
Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M10 Length: 20mm

#S218#

1021972

988185

Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M10 Length: 50mm

1031524

988187
Manufacturer: Volvo Bolt/Nut version: with Collar Bolt head-/Nut profile: Outer hexagon Thread size: M10 Length: 60mm

#G963#

Split pin

1018793

664822
Position: Bolt, Park brake cable Volvo S90, V90: all models

#G1097#

1027200

1224786

#S219#

#G572#

Washer

1019964

986499

1019970

986500

1020258

986501
Manufacturer: Volvo Inner Diameter: 8mm Outer Diameter: 22mm Thickness: 2mm Surface: burnished

file:///K|/ownersdocs/1998/1998_SV90/98S90_009.htm (4 of 5)12/30/2006 1:52:35 PM
Reporting Safety Defects in the U.S. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Volvo Cars of North America. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your retailer, or Volvo Cars of North America. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393
safety. We also want to know if you ever have a safety concern with your car. Call us in the U.S. at: 800-458-1552 or in Canada at: 800-663-8255.
road, and water conditions, particularly with regard to stopping distance.
(or 366-0123 in Washington, D.C. area) or write to: NHSTA, U.S. Department of Transportation, Washington D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.
file:///K|/ownersdocs/1998/1998_SV90/98S90_009.htm (5 of 5)12/30/2006 1:52:35 PM
Chapter 2 - Instruments, switches and controls Instruments, switches and controls pg. 14
Instruments, switches and controls pg. 15
Shiftlock When your car is parked, the gear selector is locked in the (P)ark position. To release the selector from this position, turn the ignition key to position II (or start the engine), depress the brake pedal, press the button on the front side of the gear selector and move the selector from (P) ark. If it is necessary to manually override the Shiftlock system:
Some of the items below are available on certain models only. Air vent.pg. 25 Headlights, parking lights.pg. 20 Rear fog light.pg. 22 Front fog lights.pg. 22 Space for additional equipment Power antenna (sedans only).pg. 22 Instruments.pg. 15-17 Electrically operated sun roof.pg. 23, Electrically operated sun roof.pg. Heated rear window/side door mirrors.pg. Hazard warning flasher.pg. Central lock switch.pg. Air vents.pg. Heating and ventilation.pg. 25-Passenger's side SRS (air bag).pg. Audio system.pg. 131
Turn the starting (ignition) key to position I Press firmly on the OVERRIDE" button located near the base of the gear selector. While holding the override button down, move the gear selector from the (P)ark position.

Keylock

1 Fasten the seat belt. CAUTION: Engine should be idling; never accelerate until after you feel the gear engage! Too rapid acceleration immediately after selecting a gear will cause harsh engagement and premature transmission wear.
WARNING! Before starting, check that the seat is adjusted properly. Make sure the brake pedal can be depressed completely. Move the seat closer if necessary. Refer to section "Front seats".
3Without touching the accelerator pedal ,turn the ignition key to the starting position. Allow the starter to operate for 5-10 seconds. Release the key as soon as the engine starts. If the engine fails to start, repeat step 3.
file:///K|/ownersdocs/1998/1998_SV90/98S90_053.htm (5 of 6)12/30/2006 1:52:41 PM
For cold starts at altitudes above 6000 ft (1800 m), depress the accelerator pedal halfway and turn the key to the starting position. Release the accelerator pedal slowly when the engine starts.
4 To release the gear selector, depress the brake pedal.See page 61 for instructions on manually overriding the SHIFTLOCK system if the lever cannot be moved. Do not race a cold engine immediately after starting. Oil flow may not reach some lubricating points fast enough to prevent engine damage.
WARNING! Never leave car unattended with engine running. Always open the garage doors fully before starting the engine inside a garage to ensure adequate ventilation. The exhaust gases contain carbon monoxide, which is invisible and odorless but very poisonous.
NOTE: q Do not exceed 3000rpm until the ticking sound disappears. q Selecting position P or N when idling at a standstill for prolonged periods of time will help prevent overheating of the transmission oil.
file:///K|/ownersdocs/1998/1998_SV90/98S90_053.htm (6 of 6)12/30/2006 1:52:41 PM
Chapter 4 (cont) Automatic transmission pg. 58
WARNING! Never leave the car when the engine is running. If, by mistake, the gear selector is moved from P the car may start moving.
R(Reverse) P(Park) Use this position when starting the engine or parking the car. Never use P while car is in motion. The transmission is mechanically locked when in position P. Also use the parking brake when parking on grades. The gear selector is locked in the P position (Shift lock). To release the selector, start the engine and depress the brake pedal. See page 61 for instructions on manually releasing the gear selector. Never engage R while car is moving forward. N(Neutral) Neutral position = no gear is engaged. Use parking brake. The engine can be started with the gear selector in this position. D(Drive) D is the normal driving position and should be used as often as possible to help improve fuel economy. When modes E or S are selected, upshift and downshift of the forward gears occur automatically and are governed by accelerator pedal position and vehicle speed. 3 (Intermediate position) Automatically shifts up and down between first second

L (Low gear) The gearbox does not upshift in position L! Select position L if you wish to drive in first or second gear and you do not wish to shift up (when driving in hilly terrain, for example, as position L provides the best engine braking power). The transmission will conspicuously shift down from second to first if road speed drops to below 25 or 20 mph (40 km/h or 30 km/h) (engines B6304 and B6254 respectively) when driving in Economy mode. When driving in Sport mode, the same very noticeable shift takes place if the speed drops to below 6 mph (10 km/h).
file:///K|/ownersdocs/1998/1998_SV90/98S90_058.htm (1 of 7)12/30/2006 1:52:42 PM
and third gears when in driving modes E or S. There is no upshift from third gear. Position 3 can be used for driving in hilly terrain, for towing trailers or for increased engine braking power. CAUTION: Never select P or R while the car is in motion. When initially selecting positions D, 3, L or R, your right foot should press firmly on the brake pedal to ensure that the car is standing still with the engine idling. The gear selector should not be downshifted to L at speeds above 75 mph (125 km/h). Always observe posted speed limits!
Automatic transmission pg. 59
Kick-down Automatic shift to a lower gear (kick-down) is achieved by depressing the accelerator pedal fully and briskly. An up-shift will be achieved when approaching the top speed for a particular gear or by releasing the accelerator pedal slightly. Kick-down can be used for maximum acceleration or when passing at highway speeds. The indicator lamp in the instrument panel lights up when mode W is selected. Press button W in order to disengage this mode. When mode W is disengaged, the gearbox automatically reverts to the previously selected S or E mode. If the indicator lamp begins to flash, this is an indication of a fault in the automatic gearbox. If the transmission does not shift properly, place the gear selector in position L. Please contact your Volvo retailer if this occurs.
Shift gate positions The gear selector can be moved freely between D and 3. Selections of other positions are
file:///K|/ownersdocs/1998/1998_SV90/98S90_058.htm (2 of 7)12/30/2006 1:52:42 PM
obtained by depressing the selector knob prior to moving the selector. Slightly depressing the selector knob allows selection of positions N, D, 3 and L. Fully depressing the selector knob allows selection of positions R and P. This is also necessary when initially bringing the selector out of position P. Fully depressing the selector knob thus permits shifting freely between all positions.
Mode selector Sport Mode The push-buttons to the left of the gear lever are for selection of modes E, S and W. Any mode can be selected while the car is on the move. Winter/Wet mode Enhanced Vehicle Traction This mode may be selected for starting/moving off on slippery roads or to lower downshift speeds if the transmission is in "L". In this mode: q In position D*, the gearbox starts in third gear and changes up to fourth gear. q In position 3*, second gear is locked and there is no change up to third gear. q In position L, first gear is locked. *These positions always offer the kick-down feature. CAUTION: Driveability and fuel economy will be adversely affected by prolonged driving in mode W. Volvo recommends using this mode only when starting in extremely slippery conditions. This mode is adapted to "sporty" driving characteristics. The transmission upshifts at higher engine speeds and less accelerator pedal pressure is required to initiate a downshift. Economy Mode This mode is used normally. The gearbox changes gears at a lower engine speed to achieve the best possible fuel consumption. "Lock-up" The automatic gearbox has a "lock-up" function. It reduces engine speed and saves fuel. The "lock-up" function can sometimes be felt as an additional gear change.

Electrical system When replacing the battery or when carrying out work involving the electrical system, the following should be observed: q A battery connection to the wrong terminal will damage the diodes. Before connections are made, check the polarity of the battery with a voltmeter. q If booster batteries are used for starting, they must be properly connected to minimize the risk of the diode being damaged. For correct connection, see "Jump starting" section. q Never disconnect the battery circuit (for example, to replace the battery) while the engine is running, as this will immediately ruin the generator. Always make sure that all the battery connections are properly tightened. q If any electrical-welding work is performed on the vehicle, the battery's ground lead (negative cable) and all the connecting cables of the generator must be disconnected and the welder cables placed as near the welding point as possible. q The radio must be turned off before the battery is disconnected. q If the radio has an antitheft code and the battery has been
Shiftlock release The gear selector is locked in the P position. To manually release the shift lock, turn the starting (ignition) key to position I and press firmly on the "OVERRIDE" button (located under the cover near the base of the gear selector see illustration). While holding the override button down, move the gear selector from the (P)ark position.
WARNING! The Supplemental Restraint System is grounded under the driver's seat. Do not loosen the two screws grounding the unit. Do not ground other electrical components using these screws or any other points near them. Faults in the system could occur if it is improperly grounded.
file:///K|/ownersdocs/1998/1998_SV90/98S90_058.htm (5 of 7)12/30/2006 1:52:42 PM
disconnected, the code must be re-entered before the radio will function properly.
Points to remember pg. 62
Weight distribution affects handling At the specified curb weight your car has a tendency to understeer, which means that the steering wheel has to be turned more than might seem appropriate for the curvature of a bend. This ensures good stability and reduces the risk of rear wheel skid. Remember that these properties can alter with the vehicle load. The heavier the load in the trunk, the less the tendency to understeer. Handling, roadholding Vehicle load, tire design, and inflation pressure, all affect vehicle handling. Therefore, check that the tires are inflated to the recommended pressure according to the vehicle load. See "Tire pressure" section. Loads should be distributed so that capacity weight or maximum permissible axle loads are not exceeded. WARNING! An extra mat on the driver's floor can cause the accelerator pedal to catch. Check that the movement of the accelerator pedal is not impeded. Not more than one protective floor covering may be used at one time. CAUTION: Drive slowly and carefully if going through standing water (i.e. flooded roadways, etc.). Damage to engine could result if excess water is ingested through the air intake system. Never drive the vehicle in water deeper than 1 foot (300 mm). See the flood warning on page 7. Roof rails/racks Roof rails are standard equipment on wagon models. Load bars are available as a retailer installed option on the sedan models. Observe the following points when is use: q Avoid single-point loads. Distribute the load evenly. q Place heavier cargo at bottom of load. q Observe that center of gravity and handling are influenced by load weight. q Increasing load size increases wind resistance and, thus, adversely affects fuel economy. q Anchor the cargo correctly with appropriate tie-down equipment. q Drive carefully. Avoid rapid starts, fast cornering and hard braking. q Max. roof load is 220 lbs. (100 kg) for removable racks. For permanent roof racks, check the manufacturers weight specifications.

converters.

file:///K|/ownersdocs/1998/1998_SV90/98S90_063.htm (4 of 4)12/30/2006 1:52:43 PM
Chapter 4 (cont) Brake system pg. 67
The system performs a selfdiagnostic test when the vehicle is started and at 4 mph (6 km/h). If one of the brake The driver may detect one circuits should pulsation of the brake pedal, malfunction, the red which is normal. warning light will come To obtain optimal effect from on the ABS system, constant pressure should be kept on the The pedal stroke increases brake pedal while the system slightly, the pedal feels softer is modulating the brakes. Do and extra pressure is required for not pump the brake pedal. normal braking. The switching of the ABS If the light comes on while modulator will be audible at this driving or braking, stop time. immediately and check the brake Please be aware that ABS does fluid level in the reservoir. not increase the absolute braking potential of the vehicle. While control will be enhanced, WARNING! ABS will not shorten stopping If the fluid level is below the distances on slippery surfaces. MIN mark in either section of the reservoir: DO NOT Moisture on brake DRIVE. Tow the car to a discs and brake pads Volvo retailer and have the brake system checked and affects braking. repaired.
Severe strain on the brake system
The brakes will be subject to severe strain when driving in mountains or hilly areas or towing. The speed is usually low which means that the cooling of the brakes is less efficient than when driving on level roads. To reduce the strain on the brakes it is advisable not to use the brakes excessively. Instead, shift into a lower gear, position 3 or in some cases L ,and let the engine help with the braking. Do not forget that, if you are towing a trailer, the brakes will be subjected to greater load than is normal.
If the brake powerassist does not function
Anti-lock Brake System ABS
If the warning lamp lights up there is a malfunction of the ABS system (the standard braking system will however
The power assist to the brakes functions only when the engine Driving in rain and slush or is running. When the car is passing through an automatic car moving without the engine wash can cause water to collect running the brake pedal pressure on the brake discs and pads. required to stop the car is This will cause a delay in increased by 3-4 times. braking effect when the pedal is The brake pedal feels stiff and depressed. To avoid such a delay hard. when the brakes are needed, depress the pedal occasionally when driving through rain, slush etc. This will remove the water from the brakes. Check that

file:///K|/ownersdocs/1998/1998_SV90/98S90_071.htm (4 of 5)12/30/2006 1:52:44 PM
WARNING! The traction grade assigned to this tire is based on braking (straight-ahead) traction tests and does not include cornering (turning) traction.
file:///K|/ownersdocs/1998/1998_SV90/98S90_071.htm (5 of 5)12/30/2006 1:52:44 PM
Chapter 6 - In case of an emergency

pg. 77

In case of an emergency Even if you maintain your car in good running condition, there is always the possibility that something might go wrong and prevent you from driving, such as a punctured tire, blown fuse or bulb, etc. For additional information, see section "ON CALL Road Assistance". Changing a wheel pg. 78 Temporary spare tire pg. 80 Replacing bulbs pg. 81 Replacing fuses pg. 89 Installation of accessories pg. 93 Replacing wiper blades pg. 94 Wheel changing pg. 78
file:///K|/ownersdocs/1998/1998_SV90/98S90_077.htm (1 of 4)12/30/2006 1:52:45 PM

Changing a wheel

On sedans the spare wheel, jack and toolbag are located in the trunk, beneath the carpet. The jack must be completely retracted to fit into the holder. On wagons, the spare tire and the jack are located beneath the floor mat in the large storage bin. Always secure the spare tire and the jack to prevent them from rattling.
Remove the wheel cap, using the screwdriver in the tool kit. With the car still on the ground, use the box wrench from the tool kit to loosen the wheel nuts 1/2 - 1 turn. Turn the nuts counterclockwise to loosen.
NOTE: To avoid excessive wear and the necessity of rebalancing, mark and reinstall wheels in same location and position as before removal. To lessen the chance of imbalance, each wheel hub is equipped with a guide stud to ensure that a removed wheel can be reinstalled in its original position (as when changing over to winter tires/wheels).
Wheel changing (cont.) pg. 79
WARNING! The jack attachment must engage the bar in the jack attachment (A). The car's weight must not rest on the jack's attachment (B). Be sure the jack is on a firm, level, non-slippery surface. q Never allow any part of your body to be extended under a car supported by a jack. q Use the jack intended for the car when replacing a wheel. For any other job, use stands to support the end of the car being worked on. q Apply the parking brake, select position P (automatic transmission). q Block the wheels standing on the ground. Use rigid wooden blocks or large stones. q The jack should be kept well-greased.

file:///K|/ownersdocs/1998/1998_SV90/98S90_077.htm (2 of 4)12/30/2006 1:52:45 PM

Attaching the jack

There is a jack attachment adjacent to each wheel location. Position the jack on the bar in the jack attachment as shown in the illustration above and crank while simultaneously guiding the base to the ground. The base of the jack must be flat on a level, firm, nonslippery surface. Before raising the car check that the jack is still correctly positioned in the attachment. Now raise the vehicle until the wheel is free of the ground. Unscrew the wheel nuts completely and carefully remove the wheel so as not to damage the tread of the studs.

Installing the wheel

Clean the contact surfaces on the wheel and hub. Lift the wheel and place it on the hub. Make sure that you align the wheel with the guide stud on the wheel hub prior to installation. Install the wheel nuts crosswise and tighten lightly. The conical side of the nuts should face the wheel. Lower the vehicle to the ground and alternately tighten the nuts to 63 ft. lbs. (85 Nm). Install the wheel cap.
Correct tightening order for wheel nuts

Spare tire pg. 80

WARNING! Current legislation prohibits the use of the "Temporary Spare" tire other than as a temporary replacement for a punctured tire. In other words, it must be replaced as soon as possible by a standard tire. Roadholding, etc., may be affected with the "Temporary Spare" in use. Do not, therefore, exceed 50 mph (80 km/h).
Temporary Spare (certain models)
The spare tire of your car is what is called a "Temporary Spare". Recommended tire pressure (see decal) should be maintained irrespective of which position on the car the Temporary Spare tire is used on. In the event of damage to this tire a new one can be purchased from your Volvo retailer.
file:///K|/ownersdocs/1998/1998_SV90/98S90_077.htm (3 of 4)12/30/2006 1:52:45 PM
file:///K|/ownersdocs/1998/1998_SV90/98S90_077.htm (4 of 4)12/30/2006 1:52:45 PM

Chapter 6 - (cont.) Replacing bulbs pg. 81

Replacing bulbs

The method for replacement of bulbs in the various lighting units is shown on the following pages. Make sure when installing bulbs, that the guide pin on the socket fits into its corresponding recess. When installing Halogen bulbs, do not touch the glass with your fingers because grease, oil or any other impurities can be carbonized onto the bulb and damage the reflector. Use bulbs of correct type and voltage. Failure to do so could cause the bulb failure warning light to activate.
NOTE: Turn the ignition and light switch off before replacing any bulbs.
Headlights (high/low beams)
1. Press the protruding tabs on the plastic cover and pull out towards the fender. 2. Turn the bulb and connector 1/4 turn counterclockwise and remove. 3. Remove the connector from the bulb. 4. Press a new bulb into the connector without touching the bulb itself. 5. Reinsert the bulb into the headlight housing and turn 1/4 turn clockwise until the unit seats properly. 6. Reinstall the plastic cover. Bulb Power US Bulb No. High beam 70W HB3/9005 Low beam 60W HB4/9006

Headlight adjustment

The height of the headlight beams can be adjusted according to vehicle load. The headlights should be re-aimed if heavy loads are carried in the trunk/cargo area or rear seat, or when towing a trailer. To adjust the headlights: Park the car on a level surface and open the hood. The headlights are equipped with a level which can be seen by looking through the clear "window" on the top of the headlight lens. Turn the height adjustment knob (A) until the bubble in the level aligns with within the marking lines on the level.
Lateral headlight adjustment (B) should only be carried out by an authorized Volvo retailer. This setting should be preset to "0".

Replacing bulbs pg. 82

file:///K|/ownersdocs/1998/1998_SV90/98S90_081.htm (1 of 6)12/30/2006 1:52:45 PM
Cover (seen from under car) Turn signal/parking light/side marker light 1 To remove, turn the lamp holder 1/4 turn counterclockwise. 2 Remove the bulb from the holder by pressing it down in the holder and turning it 1/4 turn counterclockwise. 3 Insert a new bulb into the holder and reinstall the unit in the reverse order. Power CP(W) Socket US Bulb No.

Fog lights

1. Release the cover with a Phillips screwdriver. 2. Remove the spring clips 3. Withdraw the bulb and connecting wire (one unit). 4. Connect the wire from the new bulb. 5. Insert the new bulb in the holder and press the spring clips into place. 6. Screw the cover into place.
2412.2(21/5) BAY 15d 1157 NA NOTE: It may be necessary to remove the washer fluid reservoir Bulb Power US Bulb No. fill tube in order to gain access to the bulb holder. H3 55W

Location ** Amperage 1 Heated rear window Central locking Brake light, Light switch Ignition switch, SRS Spare 6 Windshield wiper/washer, Headlight wiper, horn relay Climate unit Power pass. seat, Power side-view mirrors, Tailgate wiper/washer (wagons) Instrument lighting, Ambient temp. sensor Audio system Cigarette lighter/accessory socket Transmission mode selector, Gear selector light ABS Clock, Interior/glove compartment lighting, Door open warning lights, Cargo space lighting, Vanity mirror Horn 10
Location ** Amperage 15 Power antenna, Headlight flasher, Trailer Accessories Hazard warning flasher, Direction indicator, Alarm hazard indication Audio/amplifier, CD changer 15
file:///K|/ownersdocs/1998/1998_SV90/98S90_089.htm (5 of 9)12/30/2006 1:52:46 PM
19 Backup lights, Turn indicators, Cruise control Light switch, High/low beam relay Seat belt reminder, Timer- electrically heated rear window 5
Location ** Amperage 22 Heated driver's seat Heated passenger's seat Rear fog light Power seats * Power windows, Power sunroof * 30
*Automatic circuit breakers
** Some of the equipment/systems listed may be available on certain models only and/or as optional items only.
Installation of accessories pg. 93 Installation of accessories
Installation of telephone and accessories
file:///K|/ownersdocs/1998/1998_SV90/98S90_089.htm (6 of 9)12/30/2006 1:52:46 PM
In order to avoid interference and damage to your car's electrical system, your car is supplied with two connectors for the installation of a telephone and other electrical accessories. The two connectors are located beneath the glove compartment behind the soundproofing panel.
When installing the accessories or the telephone, contact an authorized Volvo workshop.
Black connector (for accessories)
Position Connection Earth (31) High beam (56 A) Rheostat (PR) Battery + (30)

Max. load 4A 1A 1A 16 A*

Yellow connector (for telephone)
Position Connection Battery + (30) Earth (31) Ignition positions I and II

Max. load 4A 1A

*The maximum combined load for Position 4 - black connector + Position 4 - yellow connector is 16A.
Replacing wiper blades pg.94
file:///K|/ownersdocs/1998/1998_SV90/98S90_089.htm (7 of 9)12/30/2006 1:52:46 PM

Replacing wiper blades

Lift the wiper arm off the windshield and hold blade at right angles to arm. Pinch the end of the plastic clip located at the back of the arm. Slide the wiper blade along the arm to release it from the hook. Install new blade (installation is the reverse of removal) and make sure that it is properly attached to the wiper arm. For reasons of safety, you should change the windshield wiper blades as soon as they start to leave marks on the windshield or fail to wipe efficiently and cleanly. To obtain maximum lifetime from a set of wiper blades, clean them with a stiff-bristle brush and warm, soapy water as part of a normal car wash.

WARNING! When the car is driven immediately after being washed, apply the brake several times in order to remove any moisture from the brake linings. Engine cleaning agents should not be used when the engine is warm. This constitutes a fire risk.
NOTE: When washing the car, remember to remove dirt from the drain holes in the doors and sills. Bumpers: Wash the bumpers with the same cleaning agent used on the rest of the car. Never clean the bumpers with gasoline or paint thinner. Difficult spots can be removed with denatured alcohol. To avoid scratches, do not dry the bumpers with paper.
*Pay special attention to the drain holes at the base of the windshield in the cowl under the rear edge of the hood.
When washing or steam cleaning the engine, avoid spraying water or steam directly on the electrical
file:///K|/ownersdocs/1998/1998_SV90/98S90_097.htm (4 of 6)12/30/2006 1:52:47 PM
components or toward the rear side of the engine.
Automatic car washing, Polishing and waxing, Chromed parts pg. 101 Automatic washing - simple and quick
An automatic wash is a simple and quick way to clean your car, but it is worth remembering that it may not be as thorough as when you go over the with sponge and water. Keeping the underbody clean is most important, especially in the winter. Some automatic washers do not have the facilities for washing the underbody. Before driving into an automatic wash, make sure that the side-view mirrors, auxiliary lamps, etc., are secure, otherwise there is risk of the machine dislodging them. You should also lower the antenna. We recommend that you do not wash your car in an automatic wash during the first six months (because the paint will not have hardened sufficiently).

Polishing and waxing

Normally, polishing is not required during the first year after delivery, however, waxing may be beneficial. Before applying polish or wax the car must be washed and dried. Tar spots can be removed with kerosene or tar remover. Difficult spots may require a fine rubbing compound. After polishing use liquid or paste wax. Several commercially-available products contain both polish and wax. Waxing alone does not substitute for polishing of a dull surface. Awide range of polymer-based car waxes can be purchased today. The waxes are easy to use and produce a long-lasting, high-gloss finish that protects the bodywork against oxidation, road dirt and fading.

Chromed parts

Chromium-plated and anodized parts should be washed with clean water as soon as they become dirty. This is particularly important if you drive on gravel roads or on roads where salt is used during the winter. After the car has been washed, apply wax or an anti-rust preparation.
Stains on chrome trim can be removed with commercially-available chrome cleaner. Do not use abrasive compounds or steel wool.

R I R R

R R R R
1) See section "Engine oil" for detailed information.
NOTE: The oil should be changed at these intervals or after 750 hours of driving or after 12 months which ever occurs first. See "Service Reminder indicator", page 19.
2) For services beyond 60,000 miles (96,000 km), consult your "Maintenance Records booklet". 3) These intervals may apply, depending on actual driving conditions (see page 109 for details) 4) For proper functioning of the vehicle and its emission control system, Volvo recommends that the
file:///K|/ownersdocs/1998/1998_SV90/98S90_103.htm (5 of 7)12/30/2006 1:52:48 PM
timing belt be replaced every 70,000 (112,000 km).
Maintenance Schedule (cont.) pg. 107
Maintenance Operation thousand miles (thousand km) MISCELLANEOUS MAINTENANCE ENGINE Fuel (Line) Filter PCV Nipple (Orifice)/hoses,clean Battery BRAKES Inspect Brakes, Replace components as necessary Brake Fluid STEERING Rotate tires/check tire wear; (Align if needed.) Check power steering fluid level. BODY Power antenna (clean) Trunk, Hood Hinges and Latches Sun roof I L L I L L I L L I L L I L L I L L I I I I I I I I I I I I I I I I I I I I I I I I I (16) (32) (48) (64) (80) (96)
file:///K|/ownersdocs/1998/1998_SV90/98S90_103.htm (6 of 7)12/30/2006 1:52:48 PM
1) Replace at 100,000 miles (160,000 km). 2) Brake fluid should be changed at owner request every second year (once a year if the car is driven in mountainous areas or in areas with high humidity).
The following items should be checked weekly by the driver (it takes only a few minutes): Engine oil level Windshield wipers Brake fluid level Level of windshield washer fluid Radiator coolant level Tire pressure (all five tires) Operation of all lights Horns
The following should also be carried out at regular intervals: Washing Polishing Cleaning
file:///K|/ownersdocs/1998/1998_SV90/98S90_103.htm (7 of 7)12/30/2006 1:52:48 PM
Chapter 8 - (cont.) Engine oil pg. 108 Checking the oil level
The oil level should be checked every time the car is refuelled. This is especially important during the engine break-in period (up to the first service). CAUTION: Not checking the oil level regularly can result in serious engine damage if the oil becomes too low.
To add or change engine oil
Add oil of the same kind as already used. Capacity (including filter): 5.9 US qts = 5.75 liters

Radio System: PLL (Phase Lock Loop) system with tuned RF (Radio Frequency) front and end automatic wide band gain control. Electronic suppression circuitry (noise killer). This radio is equipped with FM-Diversity.
Frequency range: AM 87.9 - 107.9 MHz FM 530 - 1710 kHz Sensitivity AM 1.1V FM 20V Stereo separation: 35dB

Cassette deck

4-track, 2 channel stereo Full logic electronic tape transport
Tape speed: 4.76 cm/sec. Channel separation 53dB Frequency range 30-15000hz S/N (120 V) 56 dB without Dolby B NR S/N (120 V) 66 dB with Dolby B NR
file:///K|/ownersdocs/1998/1998_SV90/98S90_138.htm (5 of 6)12/30/2006 1:52:52 PM
Wow and Flutter less than 0.06 % Pinch off
"Dolby" and the double D symbol are the trademarks of Dolby Laboratories Licensing Corporation. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
file:///K|/ownersdocs/1998/1998_SV90/98S90_138.htm (6 of 6)12/30/2006 1:52:52 PM
Chapter 10 - (cont.) Audio system SC-816 Premium Sound System (certain models) pg. 145 The following pages describe the use of your SC-816
1. On/off (push) 2. q Volume (turn) q Pause/Mute (push) q Balance (pull) 3. CD mode selector - Active sound control (single) 4. CD changer selector 5. q Tape mode selector q Tape direction selector PROG 6. Bass control 7. Treble control 8. Fader control 9. q Preset buttons q CD-Disc No. selector
10. Dolby B NR button 11. CD-random play 12. Cassette eject 13. Not in use 14. Scan 15. Auto seek memory 16. q Seek tuning up/down q TP -Next/Previous song q CD -Next UP/Previous DOWN track 17. q Manual tuning q TP -fast forward/Rewind q CD -Music search UP/ DOWN 18. CD eject (single)
19. CD slot 20. Cassette slot 21. Display 22. Waveband selector (AM) 23. Waveband selectors (FM) 24. q Anti-theft LED q Disc in LED (single)
TP =Applicable only in Tape Mode
CD =Applicable only when in CD mode and connected to a CD changer.

Anti-theft code pg. 146

file:///K|/ownersdocs/1998/1998_SV90/98S90_145.htm (1 of 6)12/30/2006 1:52:53 PM
Incorrect code If an incorrect code has been entered "EEEE" is displayed. Enter the correct code. After three unsuccessful coding attempts the set will lock and remain locked for two hours. "OFF" is displayed. During this waiting period: q the battery must be connected q the ignition key must be turned to position I q the unit must be turned on Make sure the headlights are turned off to help prevent battery drain (please refer to page 20 for information on turning the headlights off).

file:///K|/ownersdocs/1998/1998_SV90/98S90_151.htm (1 of 3)12/30/2006 1:52:54 PM
A- Next selector Press the " "button and the tape will automatically advance to next song. There must be a pause of approx. 5 seconds between songs for this function to operate. B- Previous selector Press the " "button and the tape will automatically rewind to the previous song. There must be a pause of approx. 5 seconds between songs for this function to operate.
D- Scan Press this button to listen to the first five seconds of each song. Press it again to stop scanning. "SCAN" will be displayed. There must be a gap (no udio sound) of approx. 5 seconds between songs for this function to operate.

Cassette deck pg. 153

file:///K|/ownersdocs/1998/1998_SV90/98S90_151.htm (2 of 3)12/30/2006 1:52:54 PM
A- Cassette eject If the button is pressed the tape will stop and the cassette will be ejected. The radio will be automatically engaged. The radio, CD or CD changer will engage automatically (depending on which mode was activated before the tape was played).
B- To re-enter Radio mode Push one of the waveband selector buttons When the unit re-enters Radio mode, the cassette will not be ejected. C- To re-enter Tape mode If the Tape function has been disconnected and the cassette has not been ejected, the Tape mode can be re-entered by pressing the "TAPE" button.
D- To re-enter CD mode If the CD function has been disconnected and the CD has not been ejected, the CD mode can be re-entered by pressing the "CD" button. E- To re-enter CD changer mode If the CD changer function has been disconnected, the CD changer mode can be re-entered by pressing the "CHGR" button.
file:///K|/ownersdocs/1998/1998_SV90/98S90_151.htm (3 of 3)12/30/2006 1:52:54 PM
Chapter 10 - (cont.) CD - Single pg. 154
A- CD slot With the audio system on, insert a disc into the slot with the label side up. When the CD is inserted, the radio is disengaged and the CD will start to play automatically. The CD can be inserted or ejected even when the unit is switched off. When the CD has been inserted into the player, the "DISC IN" light will always be ON even if the radio, tape deck or CD changer are in use.
B- CD mode selector Press "CD" to actuate the CD mode. The track last listened to will continue to play. If the CDplayer is empty, "NO CD" will be displayed.
C- CD eject If the button is pressed the CD will stop and the disc will be ejected. The radio will be automatically engaged. The radio, tape or CD changer will engage automatically (depending on which mode was activated before the CD was played). NOTE: If the CD eject button is pressed and the disc is not removed within 12 seconds, the disc will be drawn into the CD player again.