Pub. 988-0148-622 www.lowrance.com

iFINDER Go

Handheld Mapping GPS Receiver

Operation Instructions

Copyright 2005 Lowrance Electronics, Inc. All rights reserved. Printed in USA. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance and iFINDER GO are registered trademarks of Lowrance Electronics, Inc.
eXitSource Database, copyright 2001-2005 Zenrin Co. Ltd. Exit Authority and eXitSource are trademarks of Zenrin Co. Ltd.
Lowrance Electronics may find it necessary to change or end our policies, regulations and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. For free owner's manuals and other information, visit our web site:

www.lowrance.com

Lowrance Electronics Inc., 12000 E. Skelly Dr., Tulsa, OK USA 74128-2486
WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only take advantage of all available navigation tools when traveling to a waypoint, but will also visually check to make sure a clear, safe path to the waypoint is always available. WARNING! When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for operating the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all pertinent driving, boating or flying conditions at all times. An accident or collision resulting in damage to property, personal injury or death could occur if the operator of a GPS-equipped vehicle fails to pay full attention to travel conditions and vehicle operation while the vehicle is in motion.

Introduction

Welcome to the exciting world of GPS satellite navigation! We know you're anxious to begin finding your way with this amazing technology, but we have a favor to ask. Before you grab the batteries and head outside, please give us a moment or two to explain how our manual can help you get the best performance from this remarkable little GPS unit. First, we want to thank you for buying an iFINDER. Whether you're a first-time user or a professional navigator, you'll discover that the iFINDER is a true pocket-sized, full-featured mapping GPS receiver. Our goal for this book is to get you on the road or out to the woods and water fast, with a minimum of fuss. Like you, we'd rather spend more time traveling, and less time reading the manual! In the following pages you can find instructions on how to use all of the iFINDER's basic functions. NOTE: For the power users out there, the iFINDER Go also has an Advanced Mode, which allows you an even greater degree of control over your device's settings. For details on Advanced Mode Operation, look for the iFINDER Go Advanced User's Guide on our web site, www.lowrance.com. If you would like to know more about GPS and its companion system WAAS, visit our web site and check out the GPS Product Guide section (www.lowrance.com/Support/gps.asp). It includes a GPS tutorial, frequently asked questions and a glossary.

Batteries

The unit requires two 1.5-volt AA batteries. Do not mix different battery types. Mixing battery types may cause leakage. The following page contains an 11-step quick reference for Easy Mode operation. If you don't want to carry the manual with you as you practice with iFINDER, you might consider photocopying this quick reference page and tucking it into your pocket. 1
iFINDER Easy Mode Quick Reference
1. Install two AA batteries in the battery compartment on back of case. 2. To turn on iFINDER, press and release PWR key. 3. Opening screen displays map of North America at the 4,000 mile zoom range. Rotate through the three main Page screens (Map Page, Satellite Status Page, Navigation Page) by repeatedly pressing PAGES key. Switch Pages to display Satellite Status Page. 4. Wait while unit locates satellites and calculates current position. Process is visible on Satellite page. This takes an average of 1 minute or less under clear sky conditions (unobstructed by terrain or structures). When the unit acquires position, a position acquired message appears. 5. With position acquired, press PAGES key to display Map Page, which shows a bird's eye view of the earth. You can move around the map by: Zoom in closer to see greater detail: press ZIN (zoom in key.) Zoom out to see more area, less detail: press ZOUT (zoom out key.) Scroll map north, south, east or west using arrow keys . To stop scrolling and return to current position on map, press EXIT key. 6. Set Home waypoint at your current position so you can navigate back here: press ENT|ENT. 7. Zoom/scroll map to find a nearby object or location. Use arrow keys to center cursor cross-hair over the map object or location. 8. To navigate to the selected location: press MENU|ENT|EXIT. Follow steering arrow on Map Page or compass bearing arrow on Navigation Page. 9. At destination, Arrival Alarm goes off; to clear it, press EXIT. Cancel navigation: press MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. 10. Navigate back home by Go To Home or Navigate Trail. Go Home: press FIND|ENT; follow navigation arrows. Trail: press MENU| to NAVIGATE TRAIL|ENT. Wait while route is calculated, then follow arrows. 11. Back home, Arrival Alarm goes off; press EXIT. Cancel navigation: press MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. 2

Easy Mode Operation

This section addresses Easy Mode operation for iFINDER's main GPS functions. The principles are the same in both operating modes, so this discussion also serves as a good introduction to Advanced Mode work.

The iFINDER Keypad

You'll control the iFINDER Go with its keyboard, which includes: PWR/LIGHT (Power & Light) The PWR key turns the unit on and off and activates the backlight. Turn off the unit by pressing and holding the PWR key for 3 seconds. PAGES Pressing this key switches the unit between the three different page screens in Easy Mode. (Satellite, Navigation and Map.) Each page represents one of the unit's major operation modes. MENU Press this key to show the menus, which allow you to select or adjust a feature from a list. ARROW KEYS These keys are used to navigate through the menus, make menu selections, move the map cursor and enter data. ENT/SAVE (Enter & Save) This key allows you to save data, accept values or execute menu commands. EXIT The Exit key lets you return to the previous screen and clear data or close menus. FIND The Find key launches the iFINDER search menus. ZOUT and ZIN (Zoom Out and Zoom In) These keys let you zoom the screen in or out to see either a larger geographic area on the map, or greater detail in a smaller map area. You can press ZOUT and ZIN at the same time to create a Man Overboard waypoint at your current location and begin navigating back to it.

Main Menu

Easy Mode has a single Main Menu, which contains the commands you'll use to operate your iFINDER. Some important Main Menu commands and their functions are: 3
Screen command: changes the contrast or brightness of the display. Software Info command: shows the product name and software version of the unit's operating system software, as well as copyright notices. Advanced Mode command: used to switch to Advanced Mode operation.
Easy Mode has three Page displays that represent the three major operating modes. They are the Satellite Status Page, the Navigation Page and the Map Page. They are accessed by pressing the PAGES key, which cycles among them. Navigation Page This Page has a compass rose. It shows your direction of travel and the direction to a recalled waypoint. The navigation screen looks like the one in the following image when you're not navigating to a waypoint or other destination. Your position is shown by an arrow in the center of the screen. Your trail history, or path you've taken, is depicted by the line extending from the arrow.

Present position arrow Compass rose
Trail line Navigation information display The Navigation Page looks like this when iFINDER is not navigating.
When navigating to a waypoint or following a route, the Navigation screen looks like the one shown in the following image.
Current track or heading, shown in degrees Waypoint symbol
Compass bearing to destination Bearing arrow Trail line

Destination name

Navigation information display
Navigation Page, backtracking a trail.
Satellite Status Page This Page, shown in the following images, provides detailed information on the status of iFINDER's satellite lock-on and position acquisition. To get to the Satellite Status Page: press PAGES repeatedly until the page you want appears. This page shows you the quality and accuracy of the current satellite lock-on and position calculation.
Satellite Page shown at left with no position and no satellites, in center with satellites acquired (but no lock), and at right with a 3D position lock.
WARNING: Do not begin navigating with this unit until the numbers have stopped flashing! On any display page, a flashing current position indicator/question mark symbol and flashing GPS data displays indicate that satellite lock has been lost and there is no position confirmed. Map Page The map screens show your course and track from a "bird's-eye" view. By default, this unit shows the map with north always at the top of the screen. If you're navigating to a waypoint, the map also shows your starting location, present position, course line and destination. Using the map is as simple as pressing the PAGES key. A screen similar to those in the following images appears. The arrow flashing in the center of the screen is your present position. It points in the direction you're traveling. The solid line extending from the arrow is your plot trail, or path you've taken.
Map Page screen and various zoom levels.
Use the Zoom In and Zoom Out keys to enlarge or reduce the map's coverage area and the amount of mapping detail shown. The map data loaded in your iFINDER Go contains a low-detail world map and a medium detail USA map. The Go2 model contains the same maps plus high detail USA lake, river and coastal shoreline data. 6
The low-detail world map contains some large cities and most country political boundaries. The medium-detail U.S. map contains: all incorporated cities; shaded metropolitan areas; county boundaries; some major city streets; Interstate, U.S. and state highways; lakes and streams and more than 60,000 navigation aids and 10,000 wrecks and obstructions in U.S. coastal and Great Lakes waters. The map also contains exit services information for Interstate highways. The iFINDER Go2 International contains a worldwide reference map with basic coverage of country political boundaries, major lakes, rivers and coastal waters, plus key cities, and major and minor highways.

Moving Around the Map: Zoom & Cursor Arrow Keys
The map is presented from a bird's eye view perspective. The current zoom range shows in the lower left corner of the screen. 1. Press the ZIN key (zoom in) to move in closer and see greater detail in a smaller geographic area. 2. Press the ZOUT key (zoom out) to move farther away and see less map detail, but a larger geographic area. When you are walking or riding in a vehicle, the map will automatically move as you move. This keeps your current location roughly centered on the screen. You can manually pan or scroll the map northward, southward, eastward or westward by using the arrow keys, which launches the cross-hair map cursor. This allows you to look at map places other than your current position. To clear the cursor, press EXIT, which jumps the map back to the current position or the last known position.
Selecting Any Map Item with the Cursor
1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired object. On most items, a pop-up box will give the name of the selected item. You will also notice a black ring surrounds the item as it becomes 7
selected. Once that happens, if you press FIND the Find Menu will pop up with an extra option at the top of the list: SELECTED ITEM. Press ENT to see the Waypoint Information screen for the selected item.

Set Home Waypoint

A waypoint is simply an electronic "address," based on the latitude and longitude of a position on the earth. Easy Mode allows you to save two waypoints (Home and Man Overboard). To save a Home Waypoint: 1. Press and release ENT. 2. The SAVE AS HOME WAYPOINT? menu appears, with YES highlighted. To accept yes, press ENT. The waypoint appears on the map as an X, named "Home."

Pop-up box

Save Home Waypoint menu, left. At right, Home waypoint, with X symbol and name. When selected by the cursor, the pop-up box appears.
The example shows waypoint set at the cursor location. If cursor was not active, the point would be placed at the current position. Caution: Saving a new "Home" waypoint will overwrite and erase the previous "Home" waypoint. Navigate Back Home This command will automatically take you back to the "Home" waypoint you created. 1. Press FIND|ENT; then follow navigation arrows on the Map Page or the compass rose on the Navigation Page. To stop navigating to the waypoint, use the Cancel Navigation command. 8
Navigate to Cursor Position on Map
The Go To Cursor command navigates to the current cursor position on the map. It's a quick and handy way to navigate to anything you can see on the map display. Simply select the item with the map cursor as described earlier, then press MENU|ENT to make the iFINDER begin navigating to the cursor location. The Map Page will display a dotted line from your current position to the cursor position. The Navigation Page displays a compass rose showing navigation information to your destination. See the following examples. To stop navigating to the cursor, use the Cancel Navigation command.

Creating and Saving a Trail
A trail, or plot trail, is a history of the path you have taken. On the screen, trails are represented by a solid line extending from the back of the current position arrow. This unit automatically creates a plot trail when turned on, and this trail is automatically saved in memory when the unit is turned off. The iFINDER continues recording the same trail until you "clear the trail," which erases the old trail and starts creation of a new trail.
Navigating or Backtracking a Trail
There are two methods for following your back trail. The simplest requires no menu commands at all, but provides no navigation information during the trip. The other requires only three key strokes and provides a full range of navigation data. Try both methods and see which you prefer. When hiking at walking speed, we often just use visual back trailing. At faster speeds, the Navigate Trail command is handy. Visual Back Trailing 1. On the Map Page, zoom (ZIN or ZOUT) so your flashing trail is visible. 2. Begin moving and watch the Map Page (or Navigation Page, if you prefer). Simply walk or steer so that your current position arrow traces along the trail you have just made. 9
Navigate a Back Trail 1. Press MENU| to NAVIGATE TRAIL|ENT. 2. Now, begin moving and follow your iFINDER's instructions. On the map, your original trail is visible as a flashing solid line, along with a roughly parallel dotted line indicating the back trail to follow. The map contains a steer arrow in the lower right corner. This arrow shows you where to steer to reach the next waypoint on your back trail.
North Trail waypoint symbol Steer arrow Present position arrow

Bearing arrow

Trail line

Trail waypoint symbol

When you Navigate a trail, the iFINDER gives navigation instructions on both the Map and Navigation pages.
The Navigation Page will also show the trail line and a bearing arrow, which points to the next waypoint on the trail. As you travel, the arrival alarm will go off when you near a trail waypoint, and the steer arrow (on the map) and bearing arrow (on the compass rose) will swing around and point to the next trail waypoint. Press EXIT to clear the alarm. To stop navigating along the trail, use the Cancel Navigation command. Clearing or Erasing a Trail You can erase the current trail and automatically begin recording a new one by using the Clear Trail command. 1. Press MENU| to CLEAR TRAIL|ENT. iFINDER asks if you're sure; press |ENT. 2. Return to the page by pressing EXIT. 10
LOWRANCE DATABASES LICENSE AGREEMENT
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RETURN THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RETURN USING THE ENCLOSED UPS SHIPPING LABEL AND INCLUDE: PROOF OF PURCHASE, NAME, ADDRESS, AND PHONE NUMBER. YOUR PURCHASE PRICE AND ANY APPLICABLE TAXES WILL BE REFUNDED. PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR REFUND. 1. This License Agreement applies to the one or more databases that your product may contain. We refer to these singly as a "Database" and together as the "Databases." Your product may thus include the "WBS Database" which contains worldwide background surface mapping data, the "SmartMap Database" which contains inland mapping data, or other Databases. 2. The Databases that your product may contain are licensed, not sold. We grant to you the nonexclusive, nonassignable right to use these Databases for supplemental navigation reference purposes, but only as long as you comply with the terms and conditions of this License Agreement. We reserve the right to terminate this license if you violate any aspect of this License Agreement. You are responsible for using official government charts and prudent navigation for safe travel. 3. The Databases housed in your product are protected by the copyright notices appearing on the product or its screen(s). You may NOT modify, adapt, translate, reverse engineer, decompile, disassemble, rent, lease, or resell any Database, and you may NOT create derivative works based upon any Database or its contents. Any unauthorized reproduction, use, or transfer of a Database may be a crime and may subject you to damages and attorney fees. 4. This License Agreement will terminate immediately without prior notice from us if you fail to comply with or violate any of the provisions of this Agreement. Upon termination, you will promptly return all products containing one or more Databases to us. 5. Prices and programs are subject to change without notice. 6. This License Agreement shall be governed by the laws of the State of Oklahoma and comprises the complete and exclusive understanding between you and us concerning the above subject matter.

DATABASES LIMITED WARRANTY
"We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the one or more databases that your product may contain. We refer to each of these as a "Database" or together as the "Databases." Your product may thus include the "WBS Database" which contains worldwide background surface mapping data, the "SmartMap Database" which contains inland mapping data, or other Databases. We warrant to you that we have accurately compiled, processed, and reproduced the portions of the source material on which the Databases are based. However, we are under no obligation to provide updates to the Databases, and the data contained in the Databases may be incomplete when compared to the source material. WE MAKE NO EXPRESS OR IMPLIED WARRANTY OF ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL ITSELF, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If there is a defect in any Database, your exclusive remedy shall be, at our option, either a refund of the price you paid for the product containing the defective Database or a replacement of such product. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances: (1) when the product has been serviced or repaired by anyone other than us; (2) when the product has been connected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions furnished with the product; (3) when any serial number has been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owners manual for the product. We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Your remedies under this warranty will be available so long as you can show in a reasonable manner that the defect occurred within one (1) year from the date of your original purchase, and we must receive your warranty claim no later than 30 days after such 1-year period expires. Your claim must be substantiated by a dated sales receipt or sales slip.

LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY
"We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product's written specifications, all for one (1) year from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any non-conformity with the product's written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances: (1) when the product has been serviced or repaired by anyone other than us; (2) when the product has been connected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions furnished with the product; (3) when any serial number has been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner's manual for the product. We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. REMINDER: You must retain the sales slip or sales receipt proving the date of your original purchase in case warranty service is ever required.

LOWRANCE ELECTRONICS 12000 E. SKELLY DRIVE, TULSA, OK 74128 (800) 324-1356

How to Obtain Service

in the USA:
Contact the Factory Customer Service Department. Call toll-free:

800-324-1356.

8 a.m. to 5 p.m. Central Standard Time, M-F Lowrance Electronics may find it necessary to change or end our shipping policies, regulations and special offers at any time. We reserve the right to do so without notice.

in Canada:

800-661-3983
905-629-1614 (not toll-free) 8 a.m. to 5 p.m. Eastern Standard Time, M-F
outside Canada and the USA:
Contact the dealer in the country where you purchased your unit. To locate a dealer near you, visit the web site, www.lowrance.com, and look for the Dealer Locator.
Accessory Ordering Information
LEI Extras, Inc. is the accessory source for sonar and GPS products manufactured by Lowrance Electronics. To order Lowrance accessories, please contact: 1) Your local marine dealer, outdoor equipment store or consumer electronics store. To locate a Lowrance dealer, visit the web site, www.lowrance.com, and look for the Dealer Locator. Or, consult your telephone directory for listings. 2) U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129 Call toll free in the U.S., 800-324-0045, 8 a.m. to 5 p.m. Central Standard Time, M-F, or visit our web site www.lei-extras.com. 3) Canadian customers: Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario L4W2R7 or fax 905-629-3118. Call toll free in Canada, 800-661-3983, or dial 905 629-1614 (not toll free), 8 a.m. to 5 p.m. Eastern Standard Time, M-F. Pub. 988-0148-622 Printed in USA 050405 Copyright 2005 All Rights Reserved Lowrance Electronics, Inc.

vanced navigation features. That brings us to Section 4, Advanced Mode Operation. After we introduce the Advanced Mode menus and submenus, this section contains the rest of iFINDER's command functions, organized in alphabetical order. When you come to a GPS menu command on the iFINDER screen, you can look it up in the manual by skimming over the table of contents or index, just flipping through Section 3 or scanning through the command portion of Section 4. iFINDER is ready to use right out of the box, but you can fine tune and customize its operation with dozens of options. We describe how to use general system options along with GPS options in Section 5, System Setup and GPS Setup Options. This section covers both Easy Mode and Advanced Mode options. Finally, in Section 6, we offer Supplemental Material, including a list of the GPS datums used, warranties, and customer service information. Now, if you're into the fine details, glance over the next segment on specifications to see just how much GPS power you hold in your hand. It's important to us (and our power users), but if you don't care how many waypoints iFINDER can store or how long the batteries last, skip ahead to important information on how iFINDER works, on page 3.
Capabilities and Specifications: iFINDER Go, Go2
General Display:.. 2" (51 mm) diagonal high contrast Film SuperTwist, 16-level grayscale. Resolution:.. 200V pixel x 140H pixel resolution; 28,000 total pixels. Backlighting:. Amber LED for night and low-light viewing. Input power:. 3 volts DC (two 1.5v AA batteries); operates up to 61 hours on batteries with no backlight. Operates for 30 hours with backlight set to half bright and for 18 hours with backlight set to full bright. Case size:..pocket-size, 5.15" H x 2.12" W x 1.25" D (131 x 58 x 32 mm); waterproof to IPX7 standards. Weight:.. 5.7 ounces (162 grams) with batteries. Back-up memory:.. Built-in memory stores GPS data for decades. User settings are stored when the unit is turned off. 2
Map & data memory:. Go has 32 MB of built-in memory for the map and GPS data; Go2 has 64 MB. Languages:.. 10; menu selectable by user. GPS Receiver/antenna:. Internal; 16 parallel channel GPS/WAAS. Background map:.. Go contains low-detail world map and medium-detail USA map. Go2 contains same maps plus high-detail USA shoreline data. Go2 International contains world reference map. For complete description of data contained in these maps, see information elsewhere in this manual. Position updates:.. Every one second. Man Overboard:. MOB feature precisely marks man overboard location with special icon, then automatically displays navigation data to that position. Screen alarms:.. Arrival/off-course/destination passed/anchor. Graphic symbols for waypoints or event marker icons:.. 42. Position points:. 1,000 waypoints; 1,000 event marker icons. Routes:.. 100; up to 100 waypoints per route. Plot Trails:.. 100 savable; up to 9,999 points per trail. Zoom range:.. 40 map zoom ranges; 0.02 to 4,000 miles.

How iFINDER Works

You'll navigate faster and easier if you understand how iFINDER scans the sky to tell you where you are on the earth and, where you're going. (But if you already have a working understanding of GPS receivers and the GPS navigation system, skip on ahead to Section 2, Installation & Accessories on page 9. If you're new to GPS, read on, and you can later impress your friends with your new-found knowledge.) First, think of your iFINDER as a small but powerful computer. (But don't worry we made iFINDER easy to use, so you don't need to be a computer expert to find your way!) The iFINDER includes a keypad and a screen with menus so you can tell it what to do. The screen also lets iFINDER show your location on a moving map, as well as point the way to your destination. 3
This pocket-sized computer also contains an antenna and specialized scanning receiver, something like your car radio. But instead of your favorite dance tunes, this receiver tunes in to a couple of dozen GPS satellites circling the earth. (It will also listen in to the WAAS satellites in orbit, but more about that in the upcoming segment introducing you to GPS and WAAS.) iFINDER listens to signals from as many satellites as it can "see" above the horizon, eliminates the weakest signals, then computes its location in relation to those satellites. Once iFINDER figures its latitude and longitude, it plots that position on the moving map shown on the screen. While the screen is updated once a second, your iFINDER is making these internal calculations and determining its position several times a second! The performance doesn't stop there. Stored in the permanent memory of each iFINDER is a basic background map of the entire world. We lock it in here at the factory you can't change or erase this map. Another portion of iFINDER's onboard memory is devoted to recording GPS navigation information, which includes waypoints, event marker icons, trails and routes. This lets you look back the way you came. Think of this data storage like the hard drive memory in a computer or a tape in a cassette tape recorder. You can save several different GPS data files, erase 'em and record new ones, over and over and over again.
Introduction to GPS and WAAS
Well, now you know the basics of how iFINDER does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 9, so you can install the batteries. Or you might want to see how our text formatting makes the manual tutorials easy to skim. If that's the case, move on to "How to Use This Manual" on page 6. But, if you want to understand the current state of satellite navigation, look over this segment describing how GPS and its new companion WAAS work together to get you where you're going. The Global Positioning System (GPS) was launched July 17, 1995 by the United States Department of Defense. It was designed as a 24hour-a-day, 365-days-a-year, all weather global navigation system for the armed forces of the U.S. and its allies. Civilian use was also available at first, but it was less accurate because the military scrambled the signal somewhat, using a process called Selective Availability (SA). GPS proved so useful for civilian navigation that the federal government discontinued SA on May 2, 2000, after the military developed 4

A R-A-M mounting bracket is available for your iFINDER. The mounting arm and cradle can swivel on a ball for easy viewing in any type of vehicle.

R-A-M mounting system.

Other Accessories
Other iFINDER accessories include a belt holster with a see-through cover, as well as other cable connections. If these accessories are not available from your dealer, see the accessory ordering information on the inside back cover of this manual.
See-through belt holster for the iFINDER Go.
Section 3: Easy Mode Operation
This section addresses Easy Mode operation for iFINDER's main GPS functions. The principles are the same in both operating modes, so this discussion also serves as a good introduction to Advanced Mode work. Before you turn on iFINDER and find where you are, it's a good idea to learn about the different keys, the three Page screens and how they all work together. BUT, if you just can't wait to get outside, grab the batteries and turn to the one-page Quick Reference on page 20.

Keypad

iFINDER keypad.
1. PWR/LIGHT (Power & Light) The PWR key turns the unit on and off and activates the backlight. Turn off the unit by pressing and holding the PWR key for 3 seconds. 2. PAGES Pressing this key switches the unit between the three different page screens in Easy Mode. (Satellite, Navigation and Map.) Each page represents one of the unit's major operation modes. 3. MENU Press this key to show the menus, which allow you to select or adjust a feature from a list. 4. ARROW KEYS These keys are used to navigate through the menus, make menu selections, move the map cursor and enter data. 5. ENT/SAVE (Enter & Save) This key allows you to save data, accept values or execute menu commands. 13
6. EXIT The Exit key lets you return to the previous screen, clear data or erase a menu. 7. FIND The Find key launches the iFINDER search menus. 8. ZOUT (Zoom Out) This key lets you zoom the screen out to see a larger geographic area on the map. Less detail is seen as you zoom out. 9. ZIN (Zoom In) This key lets you zoom the screen in to see greater detail in a smaller geographic area on the map.

Power/lights on and off

To turn on the unit, press PWR. To turn on the backlight, press PWR again. Pressing PWR once again will turn off the backlight. (Press EXIT to clear any message or alarm displays.) Turn off the unit by pressing and holding the PWR key for 3 seconds.

This screen shows a graphical view of the satellites that are in view. Each satellite is shown on the circular chart relative to your position. The point in the center of the chart is directly overhead. The small inner ring represents 45 above the horizon and the large ring represents the horizon. North is at the top of the screen. You can use this to see which satellites are obstructed by obstacles in your immediate area if you hold the unit facing north. The GPS receiver is tracking satellites that are in bold type. The receiver hasn't locked onto a satellite if the number is grayed out, therefore it isn't being used to solve the position. Beneath the circular graph are the bar graphs, one for each satellite in view. Since the unit has twelve channels, it can dedicate one channel per visible satellite. The taller the bar on the graph, the better the unit is receiving the signals from the satellite. The "Estimated Position Error" (horizontal position error) shown in the upper right corner of the screen is the expected error from a benchmark location. In other words, if the EPE shows 50 feet, then the position shown by the unit is estimated to be within 50 feet of the actual location. This also gives you an indicator of the fix quality the unit currently has. The smaller the position error number, the better (and more accurate) the fix is. If the position error flashes dashes, then the unit hasn't locked onto the satellites, and the number shown isn't valid. Navigation Page This Page has a compass rose. It shows your direction of travel and the direction to a recalled waypoint. The navigation screen looks like the one in the following image when you're not navigating to a waypoint or other destination. No graphic course information is displayed. Your position is shown by an arrow in the center of the screen. Your trail his16
tory, or path you've taken, is depicted by the line extending from the arrow. The arrow pointing down at the top of the compass rose indicates the current track (direction of travel) you are taking.
Track or compass heading indicator, showing direction of travel
Present position arrow Trail line

Compass rose

Navigation information display
Navigation Page, recording a trail, traveling due north. Page looks like this when not navigating to a waypoint, or following a route or trail.
When navigating to a waypoint or following a route, the Navigation screen looks like the one shown in the following image. Your ground speed, track, distance and bearing to waypoint, and course are all shown digitally on this screen. Closing speed is also known as velocity made good. It's the speed that you're making towards the waypoint. The current cross track error is shown in the Off Course line. This is the distance you are off-course to the side of the desired course line. The course line is an imaginary line drawn from your position when you started navigating to the destination waypoint. It's shown on the steering screen as a vertical dotted line. Lines on either side of the present position show the current cross track error range. The default for the cross track error range is 0.20 mile. For example, if the present position symbol touches the right cross track error line, then you are.20 mile to the right of the desired course. You need to steer left to return to the desired course. You can use the ZIN or ZOUT keys to change the cross track error range. A circular symbol depicting your destination (waypoint) appears on the screen as you approach the waypoint as shown on the screen below. 17
Travel Time is the time that it will take to reach your destination at your present closing speed. Arrival Time is the local time that it will be when you arrive at the destination, based upon your present closing speed and track.
Current track or heading, shown in degrees Waypoint symbol Compass bearing to destination Bearing arrow Trail line
Cross track error range (off course indicator)

Destination name

Navigation Page, backtracking a trail. Driver is headed due east (a 110 track) toward a waypoint 110 (bearing) away. The cross track error range (white corridor) is 0.20 miles either side of the course. The driver is headed toward waypoint 001, which is 0.21 miles away. The vehicle is very nearly on course (off course 23 feet). Traveling at a speed of 42 mph, the driver will arrive at the waypoint in 18 seconds.
Map Page The map screens show your course and track from a "bird's-eye" view. By default, this unit shows the map with north always at the top of the screen. (This can be changed using options in Advanced Mode. See the topic Map Orientation, in Sec. 5.) If you're navigating to a waypoint, the map also shows your starting location, present position, course line and destination. NOTE: When our text says, "navigating to a waypoint," we really mean navigation to any selected item, whether it is a waypoint you made, a map feature or a map place such as a city or town. Using the map is as simple as pressing the PAGES key. A screen similar to those in following images appears. The arrow flashing in the center of the screen is your present position. It points in the direction you're traveling. The solid line extending from the arrow is your plot trail, or path you've taken. (Remember, a flashing question mark on the arrow symbol or flashing text displays means iFINDER has not yet calculated a position.) 18

Pop-up box

Save Home Waypoint menu, left. At right, Home waypoint, with X symbol and name. When selected by the cursor, the pop-up box appears.
The example shows waypoint set at the cursor location. If cursor was not active, the point would be placed at the current position. Caution: Saving a new "Home" waypoint will overwrite and erase the previous "Home" waypoint. Navigate Back Home This command will automatically take you back to the "Home" waypoint you created. 1. Press FIND|ENT; then follow navigation arrows on the Map Page or the compass rose on the Navigation Page. To cancel navigation, press MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. iFINDER stops showing navigation information.
Set Man Overboard (MOB) Waypoint
One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of water fresh or salt. It's particularly dangerous at night or if you're out of sight of land. Of course, the first thing to do is remain calm and try all standard safety measures to try and rescue the person. This unit has a man overboard feature that shows navigation data to the location where the feature was activated. To activate it, press the ZOUT and ZIN keys at the same time. Your position at the time these keys are pressed is used as the man overboard position. Caution: Saving a new "Man Overboard" waypoint will overwrite and erase the previous "Man Overboard" waypoint. 24
Navigate Back to MOB Waypoint Find your way back to the accident position with the Navigation Page or Map Page. When MOB is activated, the Navigation Page automatically shows the compass rose with its bearing arrow pointing toward the man overboard position, and the destination name says "Going To Man Overboard." The Map Page displays a Man Overboard waypoint, represented by a human figure, and the steering arrow points where to steer to reach that position. The man overboard position is also stored in the waypoint table for future reference. It can be edited the same as any other waypoint in Advanced Mode. This prevents the inadvertent loss of the current Man Overboard position.
You don't need to have an emergency to use the MOB waypoint. It is the only way you can set an additional waypoint other than "Home" in Easy Mode. When you set the MOB point, just cancel navigation and then use MOB like a regular waypoint. (Remember, you can set 1,000 waypoints in Advanced Mode.) To cancel navigation to MOB, press MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. iFINDER stops showing navigation information.

Position Page, left, Position Menu, right.
Position Menu The Position Menu allows you to set your own coordinate system, change your map datum or even set your local time. Navigation Page This screen has a compass rose that not only shows your direction of travel, but also the direction to a recalled waypoint. The navigation screen looks like the one below when youre navigating to a waypoint. Your position is shown by an arrow in the center of the screen. Your trail history, or path youve taken is depicted by the line extending from the arrow. The large arrow pointing down at the top of the compass rose indicates the current track (direction of travel) you are taking. NOTE: Refer to Sec. 3, Easy Mode Operation, for further explanation and more illustrations of the Navigation Page. 1. To get to Navigation Page: press PAGE repeatedly until the page you want appears. 2. To get to Navigation Page Sub Menu: press MENU.
Navigation Page, left, Navigation Menu, right.
Navigation Menu The Navigation Menu allows you to cancel navigation, set up alarms, and plan or edit your route. Map Page The map screens show your course and track from a birds-eye view. By default, this unit shows the map with north always at the top of the screen. (This can be changed. See the topic Map Orientation, in Sec. 5.) If youre navigating to a waypoint, the map shows your starting location, present position, course line and destination. You dont have to navigate to a waypoint, however, to use the map. The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its coverage area and the amount of mapping detail shown. There are 39 available map zoom ranges, from 0.02 miles to 4,000 miles. NOTE: Refer to Sec. 3, Easy Mode Operation, for further explanation and more illustrations of the Map Page. 1. To get to Map Page: Map page is the default when iFINDER is turned on. To switch from another page to the Map Page, press PAGE repeatedly until the page you want appears. 2. To get to Map Page Menu: press MENU.
Map Page, left, Map Menu, right.
Map Menu The map menu has many options. The map menu allows you to find distances, change the orientation of your map, view map data, and other helpful map functions.

In Easy Mode: Press MENU| to CANCEL NAVIGATION|ENT| to YES|ENT. In Advanced Mode Press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT.
Navigate a Route 1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE, press MENU|MENU| to ROUTE PLANNING|ENT. 2. Press to select route name|ENT|ENT. 3. Upon arrival at your destination, cancel navigation: press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES |ENT. Navigate to Cursor Position on Map 1. Use arrow keys to center cursor cross-hair over the map object or location. 2. To navigate to the selected location: press MENU|ENT|EXIT. Follow steering arrow on Map Page or compass bearing arrow on Navigation Page. Navigate to an Icon Use the Navigate to Cursor command above, and use the cursor to select the icon. Navigate to Map Place For Map Places that are in view on the map, you can easily use the Navigate to Cursor command above; just use the cursor to select the Map Place's icon. The other method involves searching for Map Places with the Find command. (See the information on Searching later in this section for detailed instructions on Map Places searches.) 39
Whenever you locate a Map Place, the Waypoint Information screen appears (with name, position, etc.) and the GO TO command is automatically highlighted in the command box. To navigate to that Map Place, press ENT and iFINDER begins displaying navigation information to that location. Navigate to a Waypoint You can select any waypoint visible on the Map Page with the cursor, then use the Navigate to Cursor command. However, you can avoid scrolling the map to pick your waypoint if you use the Find commands: 1. Press FIND|ENT. To look up the nearest waypoint, press ENT, or to look by name (and scroll through the entire waypoint list), press |ENT. For this example, look by name. 2. If your waypoint list is a long one, you can spell out the waypoint name in the FIND BY NAME box to search for it. (Press or to change the first character, then press to move the cursor to the next character and repeat until the name is correct, then press ENT to jump to the list below.) 3. If the list is short, you can jump directly to the FIND IN LIST box by pressing ENT. Use or to select the waypoint name, press ENT and the waypoint information screen appears with the GO TO command selected. 4. To begin navigating to the waypoint, press ENT. Navigate a Trail 1. Press MENU|MENU| to MY TRAILS|ENT and a screen similar to the one below appears.

Map Places category menu.
3. Search by nearest location. At the Find By menu, press ENT. The Find by Nearest menu will show a "calculating" screen then a list of nearest Map Places will appear. Press or to select the place you want and press ENT to call up the Waypoint Information screen.
Find by nearest option, left, Calculating screen, center, places list, right.
4. Search by name of location. At the Find By menu, press |ENT. There are two options: A. You can spell out the Map Place in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, 46
then press ENT|ENT. B. Jump down to the lower selection list by pressing ENT, then press or to select a Map Place from the list, then press ENT to call up the Waypoint Information screen.
Find by name option, left, Find by name menu, right.
5. When the Map Place's Waypoint Information screen appears, you can choose to "Go To" the location by pressing ENT or find it on the map by pressing |ENT.
"Go To" Map Place option, left, "Find on Map" option, right.
Find Streets or Intersections You can use the iFINDER to find any of the streets displayed on the map.
Find a Street 1. Press FIND| to STREETS|ENT and the Find Streets menu appears.
2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, then press ENT|ENT. B. Jump down to the lower selection list by pressing ENT, then press or to select a street from the list, then press ENT. 47
Find streets or intersections menu, left, Find street by name, right.
3. The Find Streets menu reappears with the street you're searcing for in the First Street box. (In this example, it's 80th Street.) To search for that street, press to FIND FIRST STREET|ENT. A message appears asking you to wait while the unit finds the street. When the Streets Found list appears, press or to the street you are searching for and press ENT.

Waypoints

A waypoint is simply an electronic "address," based on the latitude and longitude of a position on the earth. A waypoint represents a location, spot, or destination that can be stored in memory, then be recalled and used later on for navigation purposes. Simply think of it as an electronic address. You can create a waypoint at the cursor position on the map, or at your current position while you are navigating. Create a Waypoint These techniques use the Quick Save method, the fastest and easiest way to create a waypoint.

Create Waypoint on Map

1. Use the arrow keys to move the cursor to the place where you want to make a waypoint. 52
2. Press ENT|ENT. The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypoint symbol and number appear on the map.
Create Waypoint at Current Position
1. While you are traveling, press ENT|ENT. The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 002." The waypoint symbol and number appear on the map.
Create a Man Overboard Waypoint
This unit has a man overboard feature that shows navigation data to the location where the feature was activated. To activate it, press the ZOUT and ZIN keys at the same time. Your position at the time these keys are pressed is used as the man overboard position. The unit automatically begins navigating to the MOB waypoint. For further details, see this subject in the Easy Mode Operation section.
Create a Waypoint by Average Position
This feature sets a waypoint at the current position after taking several position readings and averaging them. This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric conditions and other factors. 1. Press ENT| to AVERAGE POSITION|ENT|(cursor jumps to highlight CREATE)|ENT. 2. Wait while the unit takes points to average for the position. (The greater the number of points, the greater the accuracy.) When the desired number of points accumulates, press ENT to create and save the waypoint. 3. The Edit Waypoint menu appears. You can simply save the waypoint by pressing EXIT|EXIT or you can edit the waypoint.
Create a Waypoint by Projecting a Position
This feature sets a waypoint at a point located a specific distance and bearing from a reference position. The reference position can be selected from your waypoint list, or any item in the Map Places list. 1. Press ENT| to PROJECTED POSITION|ENT|(cursor jumps to highlight CREATE)|ENT. 2. Press to SET REFERENCE|ENT. Use and to select a waypoint or Map Place. When the point has been selected, press ENT and the point's position appears as the reference position. 3. Press to DISTANCE|ENT. Press or to change the first character, then press to the next character and repeat until the distance is correct. Press ENT. 4. Press to BEARING|ENT. Press or to change the first character, then press to the next character and repeat until the bearing is correct. Press ENT. 53

GPS Simulator Menu.

Make the desired settings, then turn the simulator on by highlighting the SIMULATOR ON box and pressing ENT key. Press EXIT to erase this menu. A message appears periodically, reminding you that the simulator is on. To turn the simulator off, repeat the above steps or turn the unit off. While in simulator mode, you can press EXIT to clear the steering and speed boxes from the screen while continuing the simulation. This will allow you to use the map cursor during a simulation. To turn steering and speed boxes back on again, return to the GPS Simulator menu, select the STEER WITH ARROWS command, and press ENT, then press EXIT|EXIT|EXIT to return to the previous page. Simulating Trail or Route Navigation In Simulator mode, your unit can automatically follow a trail or route without manual steering if you use these steps: 1. From the Map Page, go to the simulator menu. Pick a STARTING POat or near the beginning of your trail/route. Enter an approximate TRACK (shown in compass degrees) that will point you toward the start of the trail/route. 61

SITION

2. Set SPEED to zero. Select STEER WITH ARROWS command and press ENT, which turns on the simulator and returns you to the Map Page. 3. Begin navigating along the trail/route. (If you are close enough to the first waypoint, the arrival alarm will usually go off as soon as navigation begins. Press EXIT to clear the alarm.) When navigation starts, press (since you're using the Simulator's STEER WITH ARROWS command) to increase speed to the desired setting. 4. Press EXIT to turn off the steering and speed boxes. The unit will now automatically "steer" along the trail or route. When you arrive at your "destination," cancel navigation as you normally do.

Map Auto Zoom

This receiver has an auto zoom feature that eliminates much of the button pushing that other brands of GPS receivers force you to make. It works in conjunction with the navigation features. First, start navigation to a waypoint. (See the waypoint section for more information on navigating to a waypoint.) Then, with the auto zoom mode on, the unit zooms out until the entire course shows, from the present position to the destination waypoint. As you travel toward the destination, the unit automatically begins zooming in one zoom range at a time always keeping the destination on the screen. To turn this feature on, from the MAP PAGE, press MENU| to AUTO ZOOM|ENT. Repeat these steps to turn it off.

Map Data

This menu lets you turn the map off, if desired (which turns the map screen into a GPS plotter) or choose another level of map detail; turn off or on the pop-up map info boxes; or fill land areas with gray. You can also turn on or off Map Overlays, which display latitude and longitude grid lines or range rings on the map. To get to Map Data: 1. From the Map Page, press MENU| to MAP DATA|ENT.

Map Data Menu.

Earth Map Detail Press MENU| to MAP DATA|ENT. Press ENT to enter the list of available options. Choose how much information you want to appear on your screen. The options are High, Medium, Low, or Off. After the option is set, press EXIT to return to the page display. Pop-up Map Info Press MENU| to MAP DATA|ENT. Press to POPUP MAP INFO. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT to return to the page display. Fill Land Gray Press MENU| to MAP DATA|ENT. Press to FILL LAND GRAY. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT to return to the page display. Map Overlays (Range Rings; Lat/Long Grid) The map screen can be customized with four range rings and/or grids that divide the plotter into equal segments of latitude and longitude. Range rings are handy for visually estimating distances on the map. The ring diameters are based on the current zoom range. For example: at the 100 mile zoom, the screen will show two rings with your current position in the center. The large ring touching the left and right sides of the screen is 100 miles in diameter (same as the zoom range). The second smaller ring is 50 miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the ring's radius) is 25 miles (always 1/4 the zoom range). With the arrow keys and map cursor, you can scroll the map to see the third and fourth rings. In this example, the distance to the third ring is 75 miles and distance to the fourth ring is 100 miles from your current position. 63

Trail Options menu. Specific Trail Options
Delete Trail To delete a specific trail: From the Trails menu, press to trail name|ENT. The Edit Trail menu appears as seen in the following figure. Press to DELETE TRAIL|ENT| to YES|ENT. 73
New Trail To manually start a new trail or delete a trail: From the Trail Options Menu, press to NEW TRAIL|ENT. The trail menu appears as seen below:

Trail menu.

Trail Visible/Invisible and Other Trail Options The name, maximum number of points in the trail, activity, and visibility are all changed on the Edit Trail screen. The Active setting determines whether or not iFINDER is recording new points for a particular trail. On the Edit Trail menu, press or to highlight the section you wish to change, then press ENT. Make your changes, then press EXIT to erase this menu.

Units of Measure

This menu (shown below) sets the speed and distance (statute or nautical miles, meters), depth (feet, fathoms, or meters), temperature (degrees Fahrenheit or Celsius) and heading (true or magnetic) units. To change the units: In Easy Mode, you first press MENU| to UNITS OF MEASURE|ENT. In Advanced Mode, SETUP|ENT|ENT. you first press

MENU|MENU|

SYSTEM

Units of Measure Menu.

To set Speed/Distance Unit of Measure: Press ENT. Press or to change the Speed/Distance, then press ENT. After the option is set, press EXIT|EXIT to return to the page display. To set Heading: Press to HEADING|ENT. Press or to change the heading, then press ENT. After the option is set, press EXIT|EXIT to return to the page display. To set Time Format: Press to TIME FORMAT|ENT. Press or to change the time format, then press ENT. After the option is set, press EXIT|EXIT to return to the page display. To set Date Format: Press to DATE FORMAT|ENT. Press or to change the date format, then press ENT. After the option is set, press EXIT|EXIT to return to the page display.
Section 6: Supplemental Material

FCC Compliance

This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the factory customer service department for help.