Electronic users guide released subject to "Nokia Users Guides Terms and Conditions, 7th June, 1998"
Nokia 30 GSM Connectivity Terminal Users guide for modem use

9357346 Issue 2

DECLARATION OF CONFORMITY We, NOKIA CORPORATION declare under our sole responsibility that the product TME-3 is in conformity with the provisions of the following Council Directive: 1999/5/EC. A copy of the Declaration of Conformity can be found from http://www.nokia.com/phones/declaration_of_conformity/.
Copyright 2002 Nokia. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners. HyperTerminal is a registered trademark of Hilgraeve Inc. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused. The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice The availability of particular accessories may vary by region. Please check with the Nokia dealer nearest to you.

Contents

FOR YOUR SAFETY 5 1. Introduction 6
Three ways of using the Nokia 30 with a compatible PC or other compatible device: 7 Sales package 8
2. Features of the Nokia 30 9
Data connections and messaging 9 Supplementary services 11 AutoPIN 11

3. Getting started 12

Setting up the terminal 12 Installing the SIM card 13 Mounting the terminal 14 Placing the terminal 14 Terminal connectors 15 Entering the PIN code 17 Changing the PIN code 20
Configure Nokia modem options 23 Create new Dial-up connection 24 GPRS connection 27 HSCSD or CSD connection 28 Enter user name and password 29 Name your connection 29 Set up your Internet mail account 30 Additional settings 30 Settings for Dial-up connections 31 Set properties 32 Connecting to the Internet 34 Uninstalling Modem setup for Nokia Modem setup for standard modem driver 36 Communications software 37
5. Light indicators 39 6. Accessories 42 7. Troubleshooting 43
First things to check 43 Poor reception 43 Blocked PIN code 44 No connection 44 No Internet connection 45 Modem driver 45
4. Modem installation for Nokia 30 terminal 21
Modem setup for Nokia Introduction 21 Getting started 22 Modem Setup 22
Copyright 2002 Nokia. All rights reserved.
9. Nokia 30 as an M2M Communications device 48
User control mode 48 AT command mode 49 M2M System mode 49 Placing the terminal for M2M communication 50
IMPORTANT SAFETY INFORMATION 52 TECHNICAL SPECIFICATIONS 55

8. Access codes 46

CARE AND MAINTENANCE 51

FOR YOUR SAFETY

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this manual.

INTERFERENCE

All wireless devices may get interference, which could affect performance.

DO NOT USE IN HOSPITALS

Follow any regulations or rules. Do not use near medical equipment.

USE SENSIBLY

Do not touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel must install or repair equipment.

ACCESSORIES

Use only approved accessories. Do not connect incompatible products.

BACKUP COPIES

Remember to make backup copies of all important data.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its users guide for detailed safety instructions. Do not connect incompatible products.

Note: Do not switch on the terminal when wireless device use is prohibited or when it may cause interference or danger. A number of features included in this guide are called Network Services. These are special services that you arrange through your wireless service provider. Before you can take advantage of any of these Network Services, you must subscribe to them through your service provider and obtain instructions for their use from your service provider.
For example, features like wireless data connections and supplementary services are network dependent features in Nokia 30 GSM Connectivity Terminal.
s Data connections and messaging
The Nokia 30 GSM Connectivity Terminal supports five technologies for wireless data transfer, which can be used where GSM networks support them. It is possible to use different AT commands depending on the data bearer in use. Note: Before you can use GPRS, HSCSD, CSD or USSD, you must subscribe to these services. You must also save the settings for the applications used with these technologies. See Modem installation for Nokia 30 terminal on page 21.
2. Features of the Nokia 30
With GPRS (General Packet Radio Service) data is transferred over the network in small, standardized packets. Transferring data as packets makes the transfer more efficient. Given that the Nokia 30 supports GPRS multi-slot class 6, multiple timeslots can be used for data transfer at the same time.
With HSCSD (High Speed Circuit Switched Data) the Nokia 30 acts as a multi-slot class 6 terminal and it offers data transfer speeds of up to 43.2 kbit/s.
CSD (Circuit Switched Data) offers data speed of up to 14.4 kbit/s.
SMS (Short Message Service) is used to send and receive messages containing a maximum of 160 characters via the Nokia 30. SMS is a convenient way to pass data quickly and easily to and from Nokia 30 terminals.
USSD (Unstructured Supplementary Services Data) offers reliable interactive messaging services. USSD can be used to send and receive messages containing a maximum of 182 characters via the Nokia 30. With USSD, the session is established for the duration of the connection. This increases data transfer reliability and shortens response times as the delay is known. Note: USSD messages can only be sent to the network, not directly to another mobile terminal. Copyright 2002 Nokia. All rights reserved. 10
The Nokia 30 terminal also supports additional network dependent services such as: Call forwarding to forward your calls to another number you specify. Call restriction to restrict outgoing and incoming calls. Call transfer to connect two different callers with each other and then disconnect ones own call without disturbing the other two callers. Call waiting alerts you of another incoming call during a phone call. In-call handling to switch between incoming and active calls. Multiparty call to connect several callers to one conversation. Security options such as Call barring. You can take these supplementary services into use by changing the settings of Nokia 30. This can be done using e.g. the Nokia 30 Configurator.

s AutoPIN

SIM security in the Nokia 30 terminal can be achieved by using the AutoPIN feature that makes the SIM card useless to any unauthorized user. The standard PIN request is used by default in the Nokia 30, however, the AutoPIN feature can be switched on with the Nokia 30 Configurator software. The PIN code is then programmed in the terminals memory where it is relayed in unusual situations, for example when the terminal is restarted.

s Supplementary services

Getting started
s Setting up the terminal
To use the Nokia 30 GSM Connectivity Terminal for the first time, proceed as follows: 1. Install the SIM card as described on page 13. 2. Mount the terminal on the data adapter RS-232. 3. Place the terminal in a proper location considering the field strength and antennas functionality. 4. Connect the data cable RS-232 to the terminal and to a compatible PC or other compatible device. Connect the power supply ACW-5A to the terminal and to an AC wall outlet. 5. Enter the PIN code if your SIM card requires it.
Warning! To avoid damage to the SIM card, do not install, move or remove the SIM card if the power supply is connected to an AC wall outlet. Mount the terminal on the data adapter RS-232 before connecting the power supply.

3. Getting started

Keep all miniature SIM cards out of the reach of small children.
The Nokia 30 SIM card reader supports 3V small-size SIM cards. The SIM card is attached in its position with the plastic SIM cover. If you need to remove the SIM card from the terminal, do so carefully, for example using a sharp-pointed tool. Note: Removing the SIM card when the Nokia 30 is connected to the data adapter RS-232 is not possible. 1. Remove the SIM cover from the terminal by first lifting the wider end of the SIM cover upwards. 2. Insert your SIM card into the slot and make sure the golden contact area is facing upwards and the bevelled corner is on the left. 3. Replace the SIM cover by pushing the narrow end in first, then snapping the cover closed. Note: If the SIM card is installed but the Nokia 30 terminal still requires the insertion of a SIM card, this means that your SIM card is not supported by the terminal. The Nokia 30 supports 3V SIM cards only. Copyright 2002 Nokia. All rights reserved. 13

Installing the SIM card

Mount the terminal downwards on the data adapter RS-232 and use the screws supplied in the sales package to tighten the terminal in the right position. Note: If you wish to mount the terminal on a wall, first attach the data adapter RS-232 to the wall before mounting the terminal onto it.

Placing the terminal

Install the terminal either horizontally or vertically on the wall or on a horizontal surface. The best installation location can be found with the help of the Intensity of Field strength (IoF) function through the Nokia 30 light indicators (LEDs). See "Light indicators" on page 39. If the internal antenna is not adequate, the use of additional external antenna is recommended. For more detailed information on placing the terminal, refer to http:// www.forum.nokia.com if needed. Copyright 2002 Nokia. All rights reserved. 14

Mounting the terminal

Note: All radio transmitting devices send signals which may cause interference in different electronic devices ( PC, television etc). To avoid interference, place the terminal far enough from other electronic devices.

Terminal connectors

The Nokia 30 has four interfaces to connect to: M2M System, RS-232, power interface and external antenna connector. M2M System connector The M2M System connector is located at the bottom of the terminal. When mounting the terminal the M2M system connector is attached to the matching connector on the data adapter RS-232.
Caution: In order to comply with RF exposure requirements, install the terminal so that a minimum distance of 20 cm can be maintained between the antenna and all persons. If you use an external antenna, install the antenna so that a minimum distance of 20 cm can be maintained between the antenna and all persons, with antenna gain not exceeding 3 dBi.
1. Mount the Nokia 30 on the data adapter RS-232 first in order to connect the terminal with a compatible PC or other compatible devices. 2. Attach the data cable RS-232 to the adapter. 3. Connect the data cable from the terminal to a compatible PC or other compatible device. Use only the data cable RS-232 supplied by Nokia. Power connector The Nokia 30 power connector is at the back end of the terminal, opposite the light indicators. When the Nokia 30 terminal is mounted on the RS232 adapter the power interface is found under the edge of the adapter. - Connect the power cord from the power supply to the terminal. - Connect the power supply to an AC wall outlet. External antenna connector The external antenna connector is located next to the SIM card slot ( see picture on page 39). The external antenna can be used with the external antenna cable (XRM-1) accessory if the signal strength is insufficient. - To connect the external antenna cable to the Nokia 30, cut off a piece of the SIM cover to fit the cable in. - Connect an external antenna with the FME connector to the other end of the external antenna cable. Copyright 2002 Nokia. All rights reserved. 16

RS-232 connector

The PIN (Personal Identification Number) code protects your SIM card against unauthorised use. It is usually supplied with the SIM card. If the SIM card requires a PIN code, you must enter this code to be able to use the Nokia 30 terminal. When the AutoPIN feature is switched on e.g. with the Nokia 30 Configurator software, the PIN code is saved in the terminals memory and there is no need to type in the PIN code separately. In a MS Windows environment, several applications can be used to establish the connection. One such applications is HyperTerminal. You can enter the PIN code with HyperTerminal as follows (in Windows 2000): 1. Start the HyperTerminal program (Start ->Programs ->Accessories ->Communications -> HyperTerminal, then double-click the HyperTrm.exe icon). 2. In the Connection Description dialog box, type a name for the connection in the Name box (for example GSM1) and click OK.

Entering the PIN code

3. In the Connect To dialog box, there is a Connect using list. In the list, select Direct to Com X, where COM X is the COM port to which you have connected the Nokia 30 terminal. Click OK.
5. In the HyperTerminal connection window, type at and press ENTER. The program will answer OK. If you do not get an OK response, refer to the section Troubleshooting on page 43.
4. In the COM X Properties dialog box, select the port settings displayed in and click OK.
7. Press ENTER. If the PIN code you enter fails three times in succession, the code is blocked. Refer to the section Troubleshooting on page 43.

Changing the PIN code

To protect your SIM card against unauthorised use, it is a good idea to change the factory setting PIN code supplied by your service provider. Note that the PIN code request must be set to on before you can change the PIN code with an AT command. For example, to change the PIN code in the HyperTerminal connection window: 1. Type in the following AT command at+cpwd="sc","OLDPIN","NEWPIN" where OLDPIN is the old PIN code and NEWPIN the new code. 2. Press ENTER. Note: The PIN code can also be changed using the Nokia 30 Configurator software.
6. Type in the AT command at+cpin="PIN" where PIN is your PIN code.
Modem installation for Nokia 30 terminal
The Nokia 30 CD-ROM contains a Modem Setup which allows the Nokia 30 terminal to be used as a wireless modem. The setup installs PC compatible data and fax modem drivers as well as Nokia Modem Options which lets the user set parameters for data calls. Alternatively, you can use the standard modem driver supplied with MS Windows. Either of these drivers allow the Nokia 30 terminal to be used as a modem with most commercially available Internet browsers and e-mail applications The Nokia 30 Modem Options run with Windows 98/Me/2000 or Windows NT 4.0 with Service Pack 5 or newer. To connect to the Internet, to send and receive e-mail or faxes, or to transmit data from your PC, you must have previously installed the appropriate data and fax communications software.

s Modem setup for Nokia 30
Modem Setup for Nokia 30 will install the following components on your computer: Nokia 30 data and fax modem adapters which enable you to use your phone as a modem in data and fax calls Nokia Modem Options which enable you to set options for the data calls you make
4. Modem installation for Nokia 30 terminal
Before you install the ModemSetup for Nokia 30 terminal: close all the programs currently running in the PC make sure the PIN code request in the SIM card is disabled before inserting the SIM card into the terminal. If the PIN code request is activated, the PIN code can be entered with an application such as HyperTerminal. if you wish to activate the GPRS service, GPRS must be activated in the SIM card used with Nokia 30 terminal and your local Internet service provider must support GPRS service.

Modem Setup

The Nokia 30 modem driver is located on the CD-ROM or you can download the latest software from www.forum.nokia.com. 1. Open the downloaded Modem Setup for Nokia 30 terminal exe files and save the files in a chosen location. 2. Run the Set-up. OR 1. From the CD-ROM main menu, click Install Software. 2. Click Install Modem Setup for Nokia 30. 3. Click Install and follow the instructions on the screen. Be prepared to connect your phone to the PC, when prompted to do so.
In order to use the Nokia 30 terminal as a wireless modem, Nokia Modem Options must be configured for your PC. These options define the modem to be used, the connection type, GSM connection speed kbits/s and the GPRS access point. For example, to set the Installed Nokia modems using MS Windows 2000: 1. In the Windows taskbar, press Start and select Settings and Control Panel. 2. In the Control Panel, select Nokia Modem Options. 3. Select Nokia 30 (cable) from the Installed Nokia Modems. If you have a HSCSD connection from your service provider, you can use connection speed up to 43.2 kbts/s. If you have a CSD connection from your service provider, you will be limited to a connection speed of 9.6 or 14.4 kbts/s. If you have a GPRS connection from your Internet service provider, you must specify a GPRS access point for the terminal. This access point is provided by the Internet service provider who provides the SIM card used in the Nokia 30 terminal. 4. When the Nokia Modem Options settings are determined select Apply and then select OK. Copyright 2002 Nokia. All rights reserved. 23
s Configure Nokia modem options
After you have installed the modem driver required by your system, you can select the Nokia 30 terminal as your modem and start using it through a communications software application. For example, MS Windows 95/98/2000/NT 4.0 includes communications applications such as Dial-Up Networking and HyperTerminal. For set-up assistance, please refer to the user manuals for the software you are using. When using Dial-Up Networking with Windows 2000, a new dial-up connection must be specified for each type of connection. The following steps apply equally to GPRS or HSCSD /CSD dial-up connections. 1. In the Windows taskbar, press Start and select Settings and Control Panel. 2. In the Control Panel, select Network and Dial-up Connections. 3. Select Make New Connection. 4. In the Welcome to the Netwok Connection Wizard window, press Next.

s Create new Dial-up connection
6. In the Internet Connection Wizard windows, select I want to set up my Internet connection manually, or I want to connect through a local area network (LAN). Press Next.
5. Select Dial-up to the Internet in the Network Connection Wizard window and press Next.
If your PC has more than one modem driver installed, the Choose modem window will appear. You can then select Nokia 30 (cable) and press Next.
7. Select I connect through a phone line and a modem and press Next.
1. Type in the telephone number for your GPRS connection. The telephone number for the GPRS connection is provided by your Internet service provider. For more information on this number, please contact your service provider. Leave the Use area code and dialing rules box unchecked. 2. Press Next.

GPRS connection

1. Type in the telephone number for your HSCSD / CSD connection. The telephone number1 for the HSCSD / CSD connection is provided by your Internet service provider. For more information contact your Internet service provider. Be certain to check the Use area code and dialing rules box. 2. Press Next.
1. A term also used for the telephone number is ringing group.

HSCSD or CSD connection

1. Enter your username and password for the Internet access. If you do not have a username and password from your Internet service provider, you may not be able to connect to the Internet. 2. Press Next.

Name your connection

1. Type the Connection name for your new dial-up connection e.g. Nokia 30. 2. Press Next.
Enter user name and password
You should now be able to set up a Internet mail account. For more information, contact your Internet service provider. If you do not want to set up your Internet mail account at this time, select No and press Next.

s Additional settings

The Nokia 30 terminal requires that you make some additional settings before the dial-up connection process finished. Therefore do not check the box To connect to the Internet immediately, click Finish. Press Finish.
Set up your Internet mail account
To finish setting up the modem connection, some additional settings for the Nokia 30 terminal must be defined. These settings apply for both GPRS and HSCSD/CSD connections. 1. In the Windows taskbar, press Start, select Settings and Control Panel. Select Network and Dialup Connections. 2. Select the new dial-up connection you created (e.g. Nokia 30) and right-click on the icon to open the menu. 3. Select Properties from the drop down menu.
s Settings for Dial-up connections
In the dial-up connection Properties (e.g. Nokia 30 Properties) window, select the Networking tab. Press Settings.

1. Make certain that the Enable software compression in the PPP Settings window is unchecked. 2. Press OK.

Set properties

4. Complete these fields with the information provided by your Internet service provider. 5. Click on the Advanced tab.
3. Back under the Networking tab, click on the Properties button for Internet Protocol (TCP/IP).
Note: Advanced TCP/IP Settings are Internet service provider dependent. For more information, please contact your Internet service provider. 7. Press OK. 8. Press OK also in the Dial-up connection Properties (e.g. Nokia 30 Properties) Networking window.
s Connecting to the Internet
If properly configured, your Nokia 30 GSM Connectivity Terminal should now be ready to make an Internet connection. 1. In the Windows taskbar, press Start, select Settings and Control Panel. Select Network and Dialup Connections. 2. Double-click the new connection icon (e.g. Nokia 30).
6. In the Advanced TCP/IP Settings window, make certain that the Use IP header compression box is not checked.
4. When you have successfully connected to the Internet, the Connection Complete window will appear into your PC screen.
3. Enter your Internet access username and password. For more information, contact your Internet service provider.
1. In the Windows taskbar, press Start, select Settings and Control Panel. Select Network and Dialup Connections. 2. Double-click Add/Remove Programs. 3. In the Install/Uninstall tab, select Modem Setup for Nokia 30 from the list of software that can be removed. 4. Click Add/Remove. 5. Follow the instructions on the screen until the program files are removed.
s Modem setup for standard modem driver
Alternatively, you can also use the standard modem driver supplied, for example, with MS Windows. Few additional AT commands are needed to setup GSM data or GPRS configuration. These commands can also be used in other environments, like Linux or with embedded applications supporting AT commands. You can set up the modem in the following way (in Windows 2000): 1. Select Start-> Settings-> Control Panel-> Phone and Modem Options. 2. Select a standard modem in the Modem tab and press Properties. 3. Select the Advanced tab and type in the standard modem settings for CSD/HSCSD/GPRS: AT+CBST=51,01;+CHSN=6,0,0,0;+CGDCONT=,,"INTERNET"

s Uninstalling Modem setup for Nokia 30
Note: The GPRS access point name and the supported GSM data call modes are operator specific parameters. For other bit rates and connection modes ( for example the analog PSTN modem), refer to chapter 18 (Example procedures on some AT commands) on AT Command Guide for Nokia 30 GSM Connectivity Terminal provided on the Nokia 30 CD-ROM. Please contact your local service provider for more detailed instructions on how to set up the Nokia 30 as a wireless modem.
s Communications software
After you have installed the required modem driver you can select the Nokia 30 as your modem and start using it through a communications software application. For example, MS Windows 95/98/2000/NT 4.0 includes several communications applications. For assistance, refer to the user manuals of the software you are using. Copyright 2002 Nokia. All rights reserved. 37
This sample string specifies that: 43.2 kbit/s ISDN (V120) HSCSD data call mode is selected and the GPRS Access Point Name is "Internet".
Note: Only install software from sources that offer adequate protection against viruses and other harmful software.

Light indicators

The Nokia 30 GSM Connectivity Terminal has three light indicators (LEDs), which form the terminals user interface. The LED display shows the field strength and the terminal status. The LEDs appear in two colours - red and green - indicating the state of the Nokia 30 GSM terminal in three different conditions: Start-up Normal operation Special operation Note: All three LEDs can also be configured using the Nokia 30 Configurator software application so that they do not show any status and remain off during operation.
s Nokia 30 light indicators in start-up:
LED 1 Off Green scan Off Off LED 2 Off Red blink Red blink Status LED 3 Off Off Red blink Description Power off Power on, connecting to network PIN query / new PIN query PUK query Copyright 2002 Nokia. All rights reserved. 39

Green scan Green scan

5. Light indicators

Status LED 3

Description
Note: The Intensity of Field strength indicators are visible during the start-up for approximately 10 seconds before the terminal shiftes to Normal operation mode. Intensity of Field strength (IoF) function: Red blink Green blink Green Green Green Green Green Off Off Off Green Green Green Off Off Off Off Green blink Green <-105 dBm UNACCEPTABLE -105. -100 dBm UNACCEPTABLE -100. -95 dBm WEAK -95. -90 dBm WEAK -90. -85 dBm MODERATE -85. -80 dBm MODERATE >-80 dBm GOOD

you have downloaded the latest Configurator Software from the Nokia website www.forum.nokia.com.

Access codes

You can use the access codes described in this section to avoid unauthorised use of the terminal and your SIM card. Access codes can be changed via the Nokia 30 Configurator software or with specific AT commands via an appropriate application.
s PIN code (4 through 8 digits)
The PIN (Personal Identification Number) code protects your SIM card against unauthorised use. The PIN code is usually supplied with the SIM card. When the PIN code request is enabled, the code is requested each time the phone is switched on.
s PIN2 code (4 through 8 digits)
The PIN2 code, supplied with some SIM cards, is required to access some functions, such as charging unit counters. These functions are only available if supported by your SIM card.

s PUK code (8 digits)

The PUK (Personal Unblocking Key) code is required to change a blocked PIN code. The PUK code may be supplied with the SIM card. If not, contact your local service provider for the code. If you lose the code, contact your service provider.

8. Access codes

The PUK2 code, supplied with some SIM cards, is required to change a blocked PIN2 code. If you lose the code, contact your service provider.
s Security code (5 digits)
The security code can be used to avoid unauthorised use of your terminal. The factory setting for the security code is 12345. To change the security code, use the Nokia 30 Configurator software. Keep the new code secret and in a safe place.

s Barring password

The barring password is needed when using the "Call Barring" function. You obtain the password from your service provider.

s PUK2 code (8 digits)

Nokia 30 as an M2M Communications device
M2M stands for machine-to-machine, man-to-machine and machine-to-man communication. M2M is a simple way to use wireless data transmission as a link between systems, remote devices or locations and individuals. With the Nokia 30 connected to a machine through a control application, you can remotely control a pool of devices and receive status information, for example storage statuses. The Nokia 30 can be easily integrated into various applications such as vending, security, elevator control and so on. As an M2M communications device the Nokia 30 can be used in three operation modes: User control mode AT command mode M2M system mode

s User control mode

A user can control and monitor devices by mobile phone using text messages. An example of controlling a device would be to lock a door remotely with a mobile phone. With the User Control mode of Nokia 30 it is easy and economical to develop e.g. this kind of door locking system. This is possible using the built in services of the Nokia 30 and the specific input and output pins located on the M2M System Connector, see page 15. For more information on User control mode, see the Nokia website www.forum.nokia.com for more specific documentation.
9. Nokia 30 as an M2M Communications device
In AT command mode the Nokia 30 operates as a wireless modem. The wireless connection is established and data is sent using AT commands integrated in the application module. The AT command mode is available either on the D9 connector of the RS-232 adapter or on the 50-pin M2M System Connector located on the bottom of the Nokia 30 GSM Connectivity Terminal. The AT commands, which are used to control the terminal, can be found in the AT Command Guide for Nokia 30 GSM Connectivity Terminal on the Nokia 30 CD-ROM and on the Nokia website at http:// www.forum.nokia.com. The Nokia 30 GSM Connectivity Terminal supports most ITU-T V.25ter, ETS GSM 07.05 and ETS GSM 07.07 commands.

s M2M System mode

In M2M system mode the Nokia 30 GSM Connectivity Terminal operates as a part of the Nokia M2M Platform, which is a complete, wireless end-to-end solution for machine communication. Together with the Nokia M2M Gateway the Nokia 30 forms an application platform. The Nokia 30 incorporates a host of features that can be used in M2M System mode. For example, enhanced reliability and security is available in M2M System mode. The connection between the Nokia 30 and the application module is checked periodically by live checks and if the connection is broken, it can be reset automatically. Mutual authentication can also be ensured between the Nokia 30 and the Nokia M2M Gateway. In M2M System mode the wireless connection is established and data is sent using the CORBA method calls integrated in the application module.

s AT command mode

When using the Nokia 30 terminal for M2M communication, the way in which the terminal is placed is of considerable importance regarding the way in which the terminals antenna works. The antenna works better on a non-metallic surface. Metallic surfaces require more specific adjustments in order to get the terminal to work as intended. For more information on how to use the Nokia 30 GSM Connectivity Terminal for M2M communication, please visit the Forum Nokia web site at http://www.forum.nokia.com

s Placing the terminal for M2M communication

CARE AND MAINTENANCE

Your Nokia 30 GSM Connectivity Terminal is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. Keep it and all its parts and accessories out of the reach of small children. Keep it dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. Do not use or store it in dusty, dirty areas. Its moving parts can be damaged. Do not store it in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. Do not store it in cold areas. When the terminal warms up (to its normal temperature), moisture can form inside, which may damage electronic circuit boards. Do not attempt to open it. Non-expert handling may damage it. Do not drop, knock or shake it. Rough handling can break internal circuit boards. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the terminal. Do not paint the terminal. Paint can clog the moving parts and prevent proper operation. Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or attachments could damage the terminal and may violate regulations governing radio devices. When dismounting the terminal from the cradle first disconnect the power supply from the terminal. Do not install, move or remove the SIM card if the power supply is connected to an AC wall outlet. All of the above suggestions apply equally to your terminal or any accessory. If any of them is not working properly, take it to your nearest qualified service facility. The personnel there will assist you and, if necessary, arrange for service.
IMPORTANT SAFETY INFORMATION

s Power supply

The Nokia 30 GSM Connectivity Terminal power supply ACW-5A converts mains voltage to low voltage DC. Note: The power supply socket should be easily accessible and it must not be covered. The power supply is insulation class 2-covered. Warning! Dangerous voltage. Do not attempt to open the casing. Note: This power supply is for indoor use only! Do not expose the unit to water, rain or dust. The power supply should be disconnected from the socket when the terminal is not in use for a prolonged period of time or when the power supply is not connected to the terminal. When you disconnect the power cord of the power supply, grasp and pull the plug, not the cord. Important! Use only the power supply approved by Nokia. The use of any other types will incvalidate any approval or warranty applying to the terminal, and may be dangerous.

s Electronic devices

Do not use the terminal when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Users are advised not to use the terminal when at a refuelling point (service station). Users are reminded of the need to observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas), chemical plants or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on boats; chemical transfer or storage facilities; vehicles using liquified petroleum gas (such as propane or butane); areas where the air contains chemicals or particles, such as grain, dust or metal powders; and any other area where you would normally be advised to turn off your vehicle engine.
s Potentially explosive atmospheres

TECHNICAL SPECIFICATIONS

Dimensions: 84 x 53 x 26 mm with RS-232 adapter: 109 x 76 x 34 mm Weight: 65 g with RS-232 adapter: 130 g Power supply ACW-5A Charger type: Switched mode power supply AC mains plug type: Europe, UK, US Input voltage: 90-264 VAC DC connector: 3.0 mm DC plug Weight: 70 g + cables
Volume: <110 cm3 Environmental specifications Operating conditions: -10 C.+55 C Storage conditions -40 C.+85 C Relative humidity range for operation 20.75% non-condensing and for storage 5.95% noncondensing. The terminal is not protected against ingress of water or liquids of any type.
Electro-magnetic compatibility The terminal is tested for electro-magnetic compatibility (EMC) according to the EN 301 489-1/7/standards.

<P1> the maximum number of dictionary entries which should be negotiated <P2> the maximum string length to be negotiated
6.1.15 +DR Data compression reporting
Command Set Read Test +DR=<mode> +DR? +DR=? +DR: <mode> +DR: (0,1) Response Default 0
The +DR command controls the presentation of the +DR intermediate result code. Defined values <mode> data compression reporting: 0 disabled 1 enabled, i.e. + DR result code transmitted
6.2 DE FACTO 6.2.1 B CCITT/Bell mode

Command Execute B[0].B1

The B command is ignored.

23/107

6.2.2 S1 Ring count
Command Read S1? Response <n> <n> values 000.255
The S1 command returns the number of rings (RING or +CRING result codes) counted after the last MT call setup.
6.2.3 S2 Escape code character
Command Set Read S2=<n> S2? <n> Response <n> values 0.127 (default 43) 000.127
The S2 command specifies the character to be used in the escape sequence. The default character is a plus sign. See also the +++ Escape command.
6.2.4 S12 Escape guard time
Command Set Read S12=<n> S12? <n> Response <n> values 0.255 (default 50) 000.255
The S12 command sets the guard time before and after the escape sequence. The value is in fiftieths of a second (the default is one second). See also the +++ Escape command.

6.2.5 +++ Escape

During the online data state, it is possible to enter the online command state by giving three identical characters (defined by S2register; the default is +) in a sequence. Before and after the sequence, there must be a pause of at least the time defined by the S12 register. By setting S12 to zero, an escape sequence detection can be disabled.

24/107

6.3 GSM 07.07 6.3.1 +CSTA Select type of address
Command Set Read Test +CSTA=<type > +CSTA? +CSTA=? +CSTA: <type> +CSTA: (129, 145) Response Default 129
The +CSTA command selects the type of number according to GSM specifications. The dial command D always uses this setting, except for when the dial string includes the international access code character (+). In this case, the type of address sent to the network defaults to 145. Defined values <type> type of number, refer to GSM 04.08 10.5.4.7: Unknown/telephony International/telephony

31/107

<codings>:
is a sum of integers, each representing a supported channel coding: 12 9.6k full rate data traffic channel 14.4k full rate data traffic channel Both 9.6k and 14.4k supported
<maxAiur>: integer type; the maximum value for <wAiur> (assuming that all supported channel codings are accepted and that the maximum number of time slots is used) <modify>: <wAiur>/<wRx> modification during call is not supported (<topRx> accepts only 0) <wAiur>/<wRx> modification during call is supported by ME/TA
NOTE! The non-transparent/transparent data service shall be selected by the at+cbst command.
6.3.13 +CHSC HSCSD Current call parameters
Command Execute Test +CHSC +CHSC=? Response +CHSC: <rx>,<tx>,<aiur>,<coding>
Defined values <rx>: <tx>: <aiur>: integer type; the number of receive time slots currently in use integer type; the number of transmit time slots currently in use integer type; the current air interface user rate (in the case of a transparent service, this equals a fixed network user rate). Refer to the +CHSN command for the possible values. current channel coding (Refer to the +CHSD command for the possible values). +CVHU voice hang up control

<coding>:

When there is no call in progress, all parameter values are zero.

32/107

6.3.14 +CV120 V.120 rate adaptation protocol
Command Set +CV120=<rah>,<mfm>,<mode>, <llineg>,<assign>,<negtype> Read +CV120? +CV120: <rah>,<mfm>,<mode>, <llineg>,<assign>,<negtype> Test +CV120=? +CV120: (1),(0,1),(1),(0),(0),(0) Response Default ,1
6.3.15 +CVHU Voice Hang Up Control
Command Set Read Test +CVHU=<mode> +CVHU? +CVHU=? +CVHU: <mode> +CVHU: (0-2) Response Default 0
By default, Nokia products should ignore the DTR drop, but should disconnect from the ATH during a call that is in voice mode. (GSM 07.07 section 6.).

33/107

NETWORK SERVICE COMMANDS (GSM 07.07)
7.1 +CREG NETWORK REGISTRATION
Command Set Read Test +CREG=<n> +CREG? +CREG=? +CREG: <n>,<stat>[,<lac>,<ci>] +CREG: (0-2) Response Default 0 x +cme error

47/107

SIM PUK2
ME is waiting for a SIM PUK2 (it is recommended that this <code> be returned only if the last executed command resulted in a PUK2 authentication failure (i.e. +CME ERROR: 18); if PUK2 and the new PIN2 are not entered immediately after the failure, it is recommended that the ME should not block its operation) ME is waiting for a network personalisation password ME is waiting for a network personalisation unblocking password ME is waiting for a network subset personalisation password ME is waiting for a network subset personalisation unblocking password ME is waiting for a service provider personalisation password ME is waiting for a service provider personalisation unblocking password ME is waiting for a corporate personalisation password ME is waiting for a corporate personalisation unblocking password
PH-NET PIN PH-NET PUK PH-NETSUB PIN PH-NETSUB PUK PH-SP PIN PH-SP PUK PH-CORP PIN PH-CORP PUK

8.2 +CBC BATTERY CHARGE

Command Execute Test +CBC +CBC=? Response +CBC: <bcs>,<bcl> +CBC: (0,1),(0-100) +cme error x
Optional. See ETSI GSM 07.07 /2/, section 8.4. Returns ME battery charging status and charge level. Defined values <bcs> battery charge state 1 battery is being charged

48/107

8.3 +CSQ SIGNAL QUALITY
Command Execute Test +CSQ +CSQ=? Response +CSQ: <rssi>,99 +CSQ: (0-31,99),(99) +cme error X
The +CSQ command returns the received signal strength indication <rssi>. The test command returns the supported values. Defined values <rssi> 24 indicates the quality of the network coverage: No network coverage Nokia 30 is connected to the network Satisfactory coverage Good coverage Excellent coverage
8.4 +CPBS SELECT PHONEBOOK MEMORY STORAGE
Command Set Read Test +CPBS=<storage> +CPBS? +CPBS=? +CPBS: <storage> +CPBS: ("ME","SM","FD") Response Default "SM" X +cme error
The +CPBS command selects the phonebook memory storage <storage> that is used by the other phonebook commands. The read command returns the currently selected memory, the number of used locations and the total number of locations in the memory. The test command returns the supported storages.
Defined values <storage>: "FD" "ME" "SM" SIM fixed-dialling phonebook ME phonebook SIM phonebook

49/107

8.5 +CPBR READ PHONEBOOK ENTRIES
Command Execute +CPBR=<index1>, <index2> Test +CPBR=? Response [+CPBR: <index1>,<number>,<type>,<text>[[.] <CR><LF>+CPBR: <index2>,<number>,<type>,<text>]] +CPBR: (<index>-list),[<nlength>],[<tlength>] x +cme error x

integer type; the number of messages currently in <memx> integer type; the total number of message locations in <memx>

55/107

10.3 +CMGF MESSAGE FORMAT
Command Set Read Test +CMGF=<mode> +CMGF? +CMGF=? +CMGF: <mode> +CMGF: (0,1) Response Default 0
The +CMGF command tells the Nokia 30 the input and output format of messages to be used. <mode> indicates the format of the messages used with the send, list, read and write commands and the unsolicited result codes resulting from the received messages. The mode can either be the PDU mode (entire TP data units used) or the text mode (headers and body of the messages given as separate parameters). The text mode uses the character set specified by the command Select TE Character Set +CSCS to be used in the message body. The test command returns the supported modes as a compound value.
Defined values <mode>: PDU mode text mode
10.4 +CSCA SERVICE CENTRE ADDRESS
Command Set Read Test +CSCA=<sca>,<tosca> +CSCA? +CSCA=? +CSCA: <sca>,<tosca> Response Default "",129
The +CSCA command updates the SMSC address through which mobile-originated SMs are transmitted. In text mode, the setting is used by the send and write commands. In the PDU mode, the setting is used by the same commands, but only when the length of the SMSC address coded into TPDU equals zero. The SMSC address may also change when the +CRES is taking action. The read command returns the current SMSC address settings.
Defined values <sca> GSM 04.11 RP SC address Address-Value field in string format

56/107

<tosca>
GSM 04.11 RP SC address Type-of-Address octet in integer format: unknown/telephony international/telephony
10.5 +CSMP SET TEXT MODE PARAMETERS
Command Set Read Test +CSMP=<fo>,<vp>,<pid>,<dcs> +CSMP? +CSMP=? +CSMP: <fo>,<vp>,<pid>,<dcs> Response Default 17,167,0,0
The +CSMP command is used to select values for the additional parameters needed when the SM is sent to the network or placed in storage when the text format message mode is selected. It is possible to set the validity period starting from the moment when the SM is received by the SMSC (<vp> is in range 0. 255) or to define the absolute time of the validity period termination (<vp> is a string). The format of <vp> is given by <fo>. The values of these parameters may also change when the +CRES is used. NOTE: When storing an SMS-DELIVER from the TE to the preferred memory storage in the text mode (refer to command Write Message to Memory +CMGW), the <vp> field can be used for <scts>.

Defined values <fo> <vp> <pid> <dcs> first octet of GSM 03.40 SMS-DELIVER or SMS-SUBMIT in integer format depending on the SMS-SUBMIT <fo> setting: GSM 03.40 TP-Validity Period either in integer format or in time-string format GSM 03.40 TP-Protocol-Identifier in integer format GSM 03.38 SMS Data Coding Scheme in integer format
10.6 +CSDH SHOW TEXT MODE PARAMETERS
Command Set Read Test +CSDH=<show> +CSDH? +CSDH=? +CSDH: <show> +CSDH: (0,1) Response Default 0

57/107

The +CSDH command controls whether detailed header information is shown in the text mode result codes. The test command returns the supported values as a compound value.
Defined values <show>: 0 do not show header values defined in the commands +CSCA and +CSMP (<sca>, <tosca>, <fo>, <vp>, <pid> and <dcs>) nor <length>, <toda> or <tooa> in the +CMT, +CMGL, +CMGR result codes for SMS-DELIVERs and SMS-SUBMITs in text mode; for SMS-COMMANDs in the +CMGR result code, do not show <pid>, <mn>, <da>, <toda>, <length> or <cdata>. show the values in result codes
10.7 +CSCB SELECT CELL BROADCAST MESSAGE TYPES
Command Set Read Test +CSCB=<mode>,<mids>,<dcss> +CSCB? +CSCB=? +CSCB: <mode>,<mids>,<dccs> +CSCB: (0,1) Response Default 0,"","" +cms error x
The +CSCB command defines the types of CBMs that are to be received. The test command returns the supported modes as a compound value.
Defined values <mode>: <mids> <dcss> message types specified in <mids> and <dcss> are accepted message types specified in <mids> and <dcss> are not accepted
String type, all the possible combinations of GSM 03.41 CBM message identifiers, e.g. "0,1,5,320-478,922" String type, all the possible combinations of 03.38 CBM data coding schemes, e.g. "0-3,5

58/107

10.8 +CSAS SAVE SETTINGS
Command Execute Test +CSAS=<profile> +CSAS=? +CSAS: (1-1) Response Default [1] +cms error x x
The +CSAS command saves active message service settings to a non-volatile memory. The settings specified in the commands Service Centre Address +CSCA, Set Message Parameters +CSMP and Select Cell Broadcast Message Types +CSCB are saved. The SMSC address is not stored if +CSCA is not set/restored during the current session (i.e. +CSCA? returns +CSCA: "",129). The protocol ID (<pid>), data coding scheme (<dcs>) and validity period (<vp>) are not stored if the +CSMP parameter <fo> does not indicate SMSSUBMIT (i.e. bits 1-0 are not 01). In addition, the validity period is not stored if <fo> does not indicate the relative validity period format (i.e. bits 4-3 are not 10). The destination address or alpha tag cannot be stored through an AT interface. NOTE: The values that are not stored should remain intact. The test command should display the supported profile numbers for the reading and writing of settings.

Integer type value in the range of location numbers GSM 03.40 TP-Originating/Destination-Address Address-Value field in string format; type of address given by <tooda/toda> GSM 03.40 TP-Service-Centre-Time-Stamp in time-string format
<tooa/toda>/<tora> GSM 04.11 TP-Originating/Destination-Address Type-of-Address octet in integer format <length> <data> unknown/telephony internal/telephony
Integer type value that indicates the length of the message body In characters in the text mode (+CMGF=1); or integer type value that indicates the length of the actual TP data unit in octets (i.e. the RP layer, SMSC address octets are not counted in the length) in the PDU mode (+CMGF=0), SMS: GSM 03.40 TP-User-Data in the text mode responses

<data>

63/107
<fo> <mr> <ra> <dt> <st> <ct> <pdu>
First octet of GSM 03.40 SMS-DELIVER, SMS-SUBMIT, SMS-STATUSREPORT, or SMS-COMMAND in integer format GSM 03.40 TP-Message-Reference in integer format GSM 03.40 TP-Recipient-Address Address-Value field in string format; the type of address is given by <tora> GSM 03.40 TP-Discharge-Time in time-string format: yy/MM/dd,hh:mm:sszz GSM 03.40 TP-Status in integer format GSM 03.40 TP-Command-Type in integer format GSM 04.11 SC address followed by GSM 03.40 TPDU in hexadecimal format

+CMGR READ MESSAGE

Command Response text mode (+CMGF=1), SMS-DELIVER: +CMGR: <stat>,<oa>,<scts>[,<tooa>,<fo>,<pid>,<dcs>,<sca>,<tosca>, <length>]<CR><LF><data> text mode (+CMGF=1), SMS-SUBMIT: +CMGR: <stat>,<da>[,<toda>,<fo>,<pid>,<dcs>,[<vp>],<sca>,<tosca>, <length>]<CR><LF><data> text mode (+CMGF=1), SMS-STATUS-REPORT: +CMGR: <stat>,<fo>,<mr>,[<ra>],[<tora>],<scts>,<dt>,<st> text mode (+CMGF=1), SMS-COMMAND: +CMGR: <stat>,<fo>,<ct>[,<pid>,[<mn>],[<da>],[<toda>],<length><CR> <LF><cdata>] PDU mode (+CMGF=0): +CMGR: <stat>,<length><CR><LF><pdu> +cms error x

+CMSS SEND MESSAGE FROM STORAGE
Command Response Text mode (+CMGF=1) and sending ok: +CMSS: <mr>[,<scts>] Default [,"",129/145] +cms error x
+CMSS=<index>, <da>,<toda>
PDU mode (+CMGF=0) and sending ok: +CMSS: <mr>[,<ackpdu>] Test +CMSS=?
Text mode: The +CMSS command sends a message with the location value <index> from a preferred message storage location <mem2> to the network (SMS-SUBMIT or SMS-COMMAND). If a new recipient address <da> is given for the SMS-SUBMIT, it should be used instead of the one stored with the message. The reference value <mr> is returned to the TE upon successful delivery of a message. Optionally (when +CSMS <service> value is 1 and network supports it), <scts> is returned. Values can be used to identify a message upon an unsolicited delivery status report result code. PDU mode: The +CMSS command sends a message with the location value <index> from a message storage location <mem2> to the network (SMS-SUBMIT or SMS-COMMAND). If the new recipient address <da> is given for the SMS-SUBMIT, it should be used instead of the one stored with the message. The reference value <mr> is returned to the TE when a message has been delivered successfully. Optionally (when +CSMS <service> value is 1 and network supports it), <ackpdu> is returned. Values can be used to identify a message upon an unsolicited delivery status report result code.
Defined values <index> integer type; a value in the range of the location numbers supported by the associated memory

69/107

<da> <toda>
GSM 03.40 TP-Destination-Address Address-Value field in string format; type of address given by <toda> GSM 04.11 TP-Destination-Address Type-of-Address octet in integer format unknown/telephony internal/telephony
<mr> <scts> <ackpdu>
GSM 03.40 TP-Message-Reference in integer format GSM 03.40 TP-Service-Centre-Time-Stamp in time-string format GSM 03.40 RP-User-Data element of RP-ACK PDU
+CMMS MORE MESSAGES TO SEND
Command Response Default +cms error

Set Read Test

+CMMS=[<n>] +CMMS? +CMMS=? +CMMS: <n> +CMMS: (list of supported <n>s)
The set command controls the continuity of a SMS relay protocol link. When the feature is enabled (and supported by the network), multiple messages can be sent much faster as the link is kept open. The test command returns the supported values as a compound value. Defined Values <n>: disable keep enabled until the time between the response of the latest message send command (+CMGS, +CMSS, etc.) and the next send command exceeds 1-5 seconds (the exact value is up to the ME implementation); then the ME shall close the link and the TA automatically switch <n> back to 0 enable (if the time between the response of the latest message send command and the next send command exceeds 1-5 seconds (the exact value is up to the ME implementation), the ME shall close the link but the TA shall not automatically switch back to <n>=0)

+CGACT=?

Optional. The execution command is used to activate or deactivate the specified PDP context (s).
Defined values <cid> a numerical parameter which specifies a particular PDP context definition.
13.7 +CGDATA ENTER DATA STATE
Command Execute +CGDATA=<L2P>[,<cid>] Response CONNECT NO CARRIER Test +CGDATA: (PPP) Description Enter data state Data state cannot be entered
Optional. 07.60 section 10.2.6. Causes the MT to perform whatever actions are necessary to establish communication between the TE and the network using one or more GPRS PDP type(s). If the user, however, uses a non-existent <cid> value, even if it is within a valid range, DCE shall issue an ERROR result code in response to such an attempt. See +CGDCONT. Defined values <L2P> <cid> PPP 12
NOTE: GPRS Phase 1 does not support mobile-originated context modification.

79/107

14. FAX COMMANDS
The following standard facsimile (+F) command sets are supported by the Nokia 30 according to GSM 03.45 facsimile group 3 transparent. The command structures can be found in the standards referred to below: - Class 1, TIA-578-A /4/ - Class 2, TIA SP-2388 /6/ - Class 2.0, TIA-592 and ITU-T T.32 /7/ In classes 2 and 2.0, the Nokia 30 Error supports the correction mode (ECM) with 16k send and receive buffers. The facsimile commands supported by the Nokia 30 are listed below.

14.1 TIA-578-A

+FCLASS +FMI +FMM +FMR +FTS +FRS +FTM +FRM +FTH +FRH +FLO +FPR +FDD D A Select, read or test Service Class Report manufacturer identification Request model identification Request revision identification Transmit silence Receive silence Facsimile transmit Facsimile receive HDLC transmit HDLC receive Flow control select Serial port rate control Double Escape Character Replacement Originate command Answer command

14.2 TIA-592

+FCLASS +FMI +FMM +FMR Select, read or test Service Class Report manufacturer identification Request model identification Request revision identification

80/107

D A +FDT +FDR +FKS +FIP +FCC +FIS +FCS +FLI +FPI +FNS +FLP +FSP +FCR +FBU +FNR +FIE +FPS +FCQ +FRQ +FAA +FCT +FHS +FRY +FMS +FLO +FPR +FPP +FBO +FEA +FFC +FBS
Originate command Answer command Data transmission Data reception Session termination Initialise facsimile parameters DCE capabilities parameters Current session parameters Current session results Local ID strings Local polling ID strings Non-standard frame FIF octet string Indicate document to poll Request to poll Capability to receive HDLC frame reporting Negotiation message reporting Procedure interrupt enable Page status Copy quality checking Receive quality thresholds Adaptive answer DTE phase C response timeout Call termination status ECM retry count Minimum phase C speed Flow control select Serial port rate control Packet protocol control Data bit order Phase C received EOL alignment Format conversion Buffer size

81/107

14.3 TIA SP-2388
+FCLASS +FMFR +FMDL +FREV D A +FDT +FET +FDR +FDCC +FK +FDIS +FDCS +FLID +FCIG +FLPL +FSPL +FCR +FBUG +FECM +FPTS +FCQ +FBADLIN Select, read or test Service Class Request manufacturer identification Request model identification Request product revision identification Originate a call Answer a call Data transmission Transmit page punctuation Begin or continue phase C receive data Establish DCE capabilities Session termination Current session parameters Current session results Local ID string Local polling ID string Indicate document to poll Request to poll Capability to receive Session message reporting Error correction mode control Page transfer status Copy quality checking Bad line threshold
+FBADMUL Error threshold multiplier +FPHCTO DTE phase C response timeout +FAXERR T.30 session error report +FCTCRTY ECM retry count +FMINSP +FTBC +FRBC +FBOR +FREL Minimum phase C speed Phase C transmit data block size Phase C receive data block size Data bit order Phase C received EOL alignment

82/107

+FVRFC +FDFFC +FLNFC +FWDFC +FAA +FBUF
Vertical resolution format conversion Data compression format conversion Page length format conversion Page width format conversion Answer parameter Buffer size

83/107

15. RESULT CODES
15.1 V.25TER 15.1.1 Basic syntax result codes
OK, ERROR, BUSY, CONNECT, CONNECT <rate>, NO ANSWER, NO CARRIER: See the ITU-T Recommendation V.25ter, section 5.7.1 and the X, D, A and O commands in this document. Note that OK can be a result of a successful remotely-initiated in-call modification from data to speech mode, and CONNECT[<rate>] can be a result of a successful remotelyinitiated in-call modification from speech to data mode. NO CARRIER can also indicate the remote hang up of a speech call. RING: See ETSI GSM 07.07 /2/, section 7.12. See the ITU-T Recommendation V.25ter, section 6.3.4 and the +CRC command in this document. The MT voice calls or alternating voice/data calls starting with voice shall not result in this indication. When the RING result code is enabled (+CRC=0), alternating MT voice/fax calls starting with voice shall automatically be switched into the fax mode by the Nokia 30 (if +CMOD=0). Note that the RING result code is not given for waiting calls.

15.3.3 +CR Data service report
Format +CR: REL ASYNC Description Given when +CR=1 and a data call is established; informs about the type of data call being established
The +CR intermediate result code is given after a possible +COLP result code during an MO data call setup. During an MT data call setup, this is the first intermediate result code. Note that this result code should replace the CARRIER result code (when X5 is set). This result code is enabled and disabled with the +CR command.
15.3.4 +CRING Distinctive ring
Format +CRING: <type> Description Given when +CRC=1 and incoming MT call (no active or held calls in ME)
This result code is enabled and disabled with the +CRC command. NOTE: +CRING replaces the V.25ter RING result code.

86/107

Defined values <type>: FAX VOICE REL ASYNC ASYNC VOICE/REL ASYNC ALT VOICE/REL ASYNC ALT REL ASYNC/VOICE ALT VOICE/FAX ALT FAX/VOICE Facsimile (TS 62) Normal voice (TS 11) Normal data Normal data Voice followed by data (BS 81) Alternating voice/data, voice first (BS 61) Alternating voice/data, data first (BS 61) Alternating voice/fax, voice first (TS 61) Alternating voice/fax, fax first (TS 61)
15.3.5 +CLIP Calling line identification report
Format +CLIP: <number>, <type> Description Given when +CLIP=1 and a number is received from the network when an MT call is received (no active or held calls in ME)
The +CLIP result code is sent to the TE after every RING (or +CRING) result code. This result code is enabled and disabled with the +CLIP command.
Defined values <number> <type> string type phone number of a format specified by <type> type of address octet in integer format (refer GSM 04.08 subclause 10.5.4.7): unknown/telephony international/telephony
15.3.6 +CSSU Unsolicited supplementary service notification
Format +CSSU: <code> [,<index>[,<number>, <type>]] Description Given when +CSSN=,1 and some supplementary service notification is given by the network during an MT call setup or during a voice call; note that the remote release of a held call is also indicated with this result code
In the MT call setup case, the +CSSU result code is sent to the TE after every possible +CLIP result code. In the case of a waiting call, this is given after the +CCWA result code but

87/107

discarded if the Nokia 30 is in the online data state. This result code is enabled and disabled with the +CSSN command.
Defined values <index> <code>: This is a forwarded call (MT call setup) This is a CUG call (also <index> present) (MT call setup) Call has been put on hold (during a voice call) Call has been retrieved (during a voice call) Multiparty call entered (during a voice call) Call on hold has been released (this is not an SS notification) (during a voice call) Call is being connected (alerting) with the remote party in the alerting state in an explicit call transfer operation (during a voice call) Call has been connected with the other remote party in an explicit call transfer operation (number and sub-address parameters may also be present) (during a voice call or a MT call setup) Please refer to chapter Closed user group +CCUG"

String type phone number of a format specified by <type> Type of address octet in integer format (refer to GSM 04.08, subclause 10.5.4.7): Unknown/telephony International/telephony
15.3.7 +CCWA Call waiting
Format +CCWA: <number>,<type>, <class> Description Given when +CCWA=1 and an incoming MT call is received when there are active or held calls in the ME; discarded if in the online data state
This command allows the controlling of the Call Waiting supplementary service. Activation, deactivation and status query are supported. When querying the status of a network service (<mode>=2), the response line for not active case (<status>=0) should be returned only if the service is not active for any <class>. The parameter <n> is used to disable/enable the presentation of an unsolicited result code +CCWA: <number>, <type>, <class>[,<alpha>] to the TE when a call waiting service is enabled. The command should be abortable when the network is interrogated.

88/107

The interaction of this command with other commands based on other GSM supplementary services is described in the GSM standard. The test command returns the values supported by the TA as a compound value.
Defined values <n> (sets/shows the result code presentation status in the TA): Disable Enable

<mode>

(when the <mode> parameter is not given, the network is not interrogated): 3 Disable Enable Query status

<classx>

A sum of integers each representing a class of information (default 7 equals all classes): 4 Voice (telephony) Data (usually refer to all bearer services; with <mode>=2 this may refer only to some bearer service) Fax (facsimile services)
Also all other values below 128 are reserved by this ETS <status>: 0 <number>: <type>: <alpha>: Not active
1 Active String type phone number of a calling address in the format specified by <type> Type of address octet in integer format (refer to GSM 04.08 [8] subclause 10.5.4.7) Optional string type alphanumeric representation of <number> corresponding to the entry found in the phonebook; the used character set should be the one selected with the command Select TE Character Set +CSCS

AT+CPIN="1234"<CR>

AT+CPIN?<CR>

+CPIN: READY OK
How to check network registration (signal quality): AT+CSQ<CR> +CSQ:31, 99 Query signal strength. Response +CSQ<rssi>, 99 (*)
(*) Values for <rssi> 0 1-31 No network coverage (Check PIN code) Signal strength

101/107

17.2 INITIALISING THE NOKIA 30
Command from the DCE Response from the Nokia 30 OK AT+IFC=1,1<CR> Explanation

AT&F<CR>

Set to factory-defined configuration. Previous command was successful Set the flow control to SW flow control; the default is HW flow control (2,2) Previous command was successful Ignore DTR changes Previous command was successful
OK AT&D0<CR> OK
17.3 MAKING A DATA CALL WITH NOKIA 30:
ATD+358705966200<CR> CARRIER CONNECT Start connection by dialling the preferred number The Nokia 30 has a data connection to the GSM infrastructure The connection to the preferred number is established and the application can start sending data
17.4 SENDING AN SMS FROM A TERMINAL OR OTHER SIMILAR APPLICATION
There are two different modes text mode and PDU (Protocol Data Unit) mode for handling short messages. The default mode of the Nokia 30 is the PDU mode (+CMGF=0). Text mode is easier to understand than the PDU mode. AT+CMGF=0<CR>
AT+CMGS=29<CR> >0011000C915358508181420000A7 1154747A0E4Acf41f4f29C9E769F41 21
Set the Nokia 30 to GSM 07.05 SMS PDU mode (default). Send the message to the defined phone number. The service number is not a mandatory field in the PDU structure. This example does not have the SMSC number.

102/107

17.5 SENDING A SAMPLE SMS IN TEXT MODE
Command from the DCE Response from the Nokia 30 Explanation

AT+CMGF=1<CR>

Set the Nokia 30 to GSM 07.05 SMS Text mode. The default value is the PDU mode (0). Previous command was successful. Set the SMS Service Centre number to be used with an outgoing SMS. Previous command was successful. Send the "My SMS" message to defined phone number. 145 specifies the phone number type.

105/107

19. REFERENCES
/1/ /2/ /3/ ITU-T Recommendation V.25ter: Serial asynchronous automatic dialling and control; Aug 1995. GSM 07.07: Digital cellular telecommunications system (Phase 2+); AT command set for GSM Mobile Equipment (ME); version 5.4.0; Nov 1997. GSM 07.05: Digital cellular telecommunications system (Phase 2+); Use of Data Terminal Equipment - Data Circuit terminating Equipment (DTE - DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS); version 5.4.0; Nov 1997. TIA-578-A Facsimile Digital Interfaces - Asynchronous Facsimile DCE Control Standard, Service Class 1; May 1995. TIA-592 Facsimile Digital Interfaces - Asynchronous Facsimile DCE Control Standard, Service Class 2; May 1995. TIA SP-2388: Proposed new standard - Asynchronous Facsimile DCE Control Standard; Aug 1990. TIA PN-3131: Project to complete IS-101 Facsimile Digital Interfaces - Voice Control Interim Standard for Asynchronous DCE; Feb 1995. ITU-T Recommendation G.711: Pulse code modulation (PCM) of voice frequencies; 1993.

/4/ /5/ /6/ /7/ /9/

/10/ GSM 03.40: Digital cellular telecommunications system (Phase 2+); Technical realisation of the Short Message Service (SMS); Point-to-Point (PP). /11/ GSM 03.38: Digital cellular telecommunications system (Phase 2+); alphabets and language-specific information. /12/ GSM 03.41: Digital cellular telecommunications system (Phase 2+); Technical realisation of the Short Message Service Cell Broadcast (SMSCB). /13/ ETS 300 342-1: Radio Equipment and Systems (RES); Electro-Magnetic Compatibility (EMC) for European digital cellular telecommunications system (GSM 900 MHz and DCS MHz).

106/107

QUESTIONS AND ANSWERS
Q. Can the application or terminal I am using directly receive an incoming SMS? A. The received SMS messages are stored in the SIM card memory "SM" by default. The messages can be read from the SIM card using AT commands, e.g., the +CMGR command. The +CNMI command (e.g. AT+CNMI=1,2,2,1,0<CR>) allows the application to receive the incoming SMS directly in all environments. The following ETSI specifications can be used as a reference when the GSM 07.05 Textand PDU modes are used: GSM 07.05, GSM 03.03, GSM 03.38, GSM 03.40, GSM 03.41, GSM 04.11. Q. What standards does the Nokia 30 support? A. There are several standards that have influenced the design of the Nokia 30. From the application's point of view, the most important standards are those that specify the ATcommand interface: ITU-T V.25ter, ETS GSM 07.07, ETS GSM 07.05, TIA-578-A, TIA592 and TIA SP-2388. These standards can be obtained from national standards organisations or at www.etsi.fr, www.tiaonline.org and www.itu.ch.

107/107