Operation and maintenance manual
Before using the machine, please read the attached operating instructions. Carefully read the safety rules
Veuillez lire attentivement le mode d'emploi (notamment les consignes de scurit) avant d'utiliser l'appareil.

Mode d'emploi

FOR HOUSEHOLD USE ONLY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 2 Do not touch hot surfaces. Use handles or knobs. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. 5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any way. Return appliance to the nearest authorized service centre for examination, repair or adjustment. 7 The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. 8 Do not use outdoors. 9 Do not let cord hang over edge of table or counter, or touch hot surfaces. 10 Do not place on or near a hot gas or electric burner, or in a heated oven. 11 Always turn appliance OFF, then plug cord into the wall outlet. To disconnect, turn switch to OFF, then remove plug from wall outlet. 12 Do not use appliance for other than intended household use. 13 Use extreme caution when using hot steam.

SAVE THESE INSTRUCTIONS

CAUTION
This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service centre. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during operation. 4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft cloth dampened with water. 5 For optimal taste of your coffee, use purified or bottled water. Periodic descaling is still recommended every 2-3 months.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of tangling or tripping over a longer cord. B Longer extension cords are available and may be used if care is exercised in their use. C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. 2 if the appliance is of the grounded type, the extension cord should be a grounding type 3 the cord should not hang from the table to avoid the risk of tangling or tripping.

CONTENTS

GENERAL INFORMATION...5 APPLIANCE....6

ACCESSORIES.....6

INSTALLATION....7
STARTING THE MACHINE.....7 AQUA PRIMA WATER FILTER (OPTIONAL)....8
CONTROL PANEL....9 ADJUSTMENTS....10
COFFEE VOLUME ADJUSTMENT PER CUP....10 DRIP TRAY HEIGHT ADJUSTMENT...10 COFFEE GRINDER ADJUSTMENT....10
COFFEE BREWING AND HOT WATER DISPENSING.. 11
COFFEE BREWING....11 HOT WATER DISPENSING....11
CAPPUCCINO.....12 DESCALING....14 CLEANING AND MAINTENANCE...16
HOW TO CLEAN THE MACHINE.....16 CLEANING THE BREW GROUP....17
TROUBLESHOOTING....18 SAFETY RULES....19 TECHNICAL DATA....21

5 GENERAL INFORMATION

This coffee machine is suitable for preparing espresso coffee using coffee beans and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use and is not suitable for heavy or professional use. Warning: no liability is assumed for any damage caused by: incorrect use not in accordance with the intended uses; repairs not carried out by authorized customer service centres; tampering with the power cable; tampering with any part of the machine; the use of non-original spare parts and accessories; failure to descale the machine or use at temperatures below 0C (32F).

IN THESE CASES, THE WARRANTY IS NOT VALID. THE WARNING TRIANGLE INDICATES ALL IMPORTANT INSTRUCTIONS FOR THE USERS SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES!
HOW TO USE THESE OPERATING INSTRUCTIONS.
Keep these operating instructions in a safe place and make them available to anyone else who would use the coffee machine. For further information or in case of problems, please refer to any authorized service centre.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

APPLIANCE

Coffee bean hopper Cup stacking surface Coffee bean hopper cover Power button
Control panel Dispensing head
Service door Dregs drawer
Drip tray + grill and oat

Hot water / steam knob

Hot water / steam spout Water tank Drip tray Brew Group

Socket for power cable

ACCESSORIES

Grinder adjustment key

Aqua Prima water lter (optional)

Power cable

Cleaning brush

INSTALLATION

STARTING THE MACHINE
Make sure the power button is not pressed and that the machine is turned off. Check the machine features on the label on the bottom of the appliance. 2
Lift the cover of the coffee bean hopper.
Fill the container with coffee beans. Close the cover placing it correctly on the hopper.
Remove the water tank. We recommend installing the Aqua Prima water lter (see page 8).
Fill the tank with fresh drinking water up to the MAX level. Reinsert the tank.
Insert the plug into the socket located in the rear panel of the machine and insert the other end into a socket with suitable current.
Firmly push down the power button to turn on the machine. The machine performs a selftest.
Place a container beneath the steam spout.
Turn the knob until the position is reached.
Wait until a steady ow of water comes out of the spout.

AQUA PRIMA WATER FILTER

Turn the knob until it is in the rest position ( ).

Remove the container.

The machine is ready for use.
When the correct temperature is reached, the machine performs a rinse cycle of the internal circuits. A small amount of water is dispensed; during this phase, the lights ash counterclockwise. Wait for this cycle to be completed.

AQUA PRIMA WATER FILTER (OPTIONAL)
To improve the quality of the water you use, it is recommended to install the Aqua Prima lter. Before using it, leave the lter immersed in the tank for 30 minutes. 2 3
Remove the Aqua Prima lter from its packaging. Enter the date of the current month.
Insert the lter in the empty tank. The reference mark and the groove must match. Push rmly until it is completely inserted. 5
Fill the tank with fresh water. Let the lter soak for 30 minutes. After 30 minutes discard the water in the tank and rell with fresh water.
Place a container beneath the steam Fill the tank again with fresh spout. Dispense the water in the drinking water. tank using the hot water function The machine is ready for use. (see page 11).

CONTROL PANEL

Alarm light to empty the dregs drawer: permanently on: signals the need to empty the dregs drawer; this operation must be performed with the machine turned on (steps 4 and 5, page 16). Coffee dose adjusting knob (see page 10). Coffee button: the button has been pushed once:1 coffee has been selected. the button has been pushed twice: 2 coffees have been selected.
Hot water/steam button: on: steam function is selected off: hot water function is selected
Alarm light: permanently on (one or more events): signals the machine is out of coffee, that the water tank is empty, or the dregs drawer is full. on and slowly ashing (one or more events): signals that the Brew Group is not inserted, the dregs drawer is not inserted, the cover of the coffee hopper is not inserted or the service door is open. on and quickly ashing: signals the need to prime the water circuit. Descaling light: on and ashing: signals the need to perform a descaling cycle (see page 14).
Machine ready light: permanently on: signals that the machine is ready for use. on and ashing: signals that the machine is warming up. on and quickly ashing: signals that the machine is too warm; dispense water. The and lights ash alternately: switch off the machine and turn it on again after 30 seconds. If this signal appears again, contact the customer service centre.

ADJUSTMENTS

COFFEE VOLUME ADJUSTMENT PER CUP
The coffee volume knob adjusts the amount of coffee brewed per cup. This adjustment has an immediate effect on the selected type of brewing. Espresso coffee Medium coffee

Long coffee

DRIP TRAY HEIGHT ADJUSTMENT
The drip tray is height-adjustable to t different sized cups. To adjust the drip tray, lift it or lower it manually until it reaches the desired height. Note: a red oat is visible in the tray; when it lifts, the tray must be drained.

COFFEE GRINDER ADJUSTMENT
The machine enables a slight adjustment of the coffee grinder. Coffee may be ground according to your own tastes. The adjustment must be performed turning the pin located inside the coffee container by means of the supplied key only. Turn the pin one setting at a time and brew 2-3 cups of coffee; the change in the grind will be noticeable after a couple of cycles. The references located inside the container indicate the grind setting.

FINE GRIND

MEDIUM GRIND

COARSE GRIND

COFFEE BREWING AND HOT WATER DISPENSING

COFFEE BREWING

The coffee brewing cycle can be interrupted at any moment by pushing the button. To brew 2 cups, the machine dispenses half of the entered quantity and briey interrupts dispensing in order to grind the second serving of coffee. Coffee dispensing is then restarted and completed. 3
Adjust the drip tray according to the height of the cup/s. 4
Place one cup if you want one coffee only. 5
Place two cups if you want two coffees. 6
Adjust the quantity of coffee by turning the knob.
Press the central button: once for 1 coffee twice for 2 coffees
The machine automatically starts brewing coffee. When the machine has nished brewing, remove the cup/s.

HOT WATER DISPENSING

Dispensing may be preceded by short sprays of hot water, and scalding is possible. The hot water/steam spout may reach high temperatures: do not touch it with bare hands. Use the appropriate handle only. 3
Adjust the height of the drip tray.
HOT WATER DISPENSING - CAPPUCCINO
Wait for the container to be lled with the desired quantity of water.

CAPPUCCINO

Fill 1/3 of the cup with cold milk.
Press the button to select the steam function. The steam light turns on.
The indicator light starts ashing. Wait until the indicator is permanently on.
Drain any residual water and wait until the spout ejects steam only. 10
Immerse the steam spout in the milk.
Turn the knob until the position is reached. 13
Froth the milk by gently swirling the container.
Press the button to dispense water. The indicator ashes.
Turn the knob until the position is reached and dispense water.
17 After frothing the milk, brew coffee into the cup for a creamy cappuccino.
When the machine ready indicator is permanently on, turn the knob until it is in the rest position.
Remove the container. When the spout is cold, disassemble it and wash it carefully.

DESCALING

When performing a descaling cycle, it is necessary to be present during the entire process (about 40 minutes). Caution! Do not use vinegar as a descaler. The descaling must be done when indicated by the machine. Use a non-toxic, non-harmful descaling solution. Saeco descaling solution is recommended. The used solution should be disposed according to the manufacturer instructions and/or regulations in the country of use. Note: before starting a descaling cycle make sure that: 1 a container of adequate size is available; 2 if the Aqua Prima lter is used, make sure that it has been removed.

When the descaling light is ashing, a descaling cycle must be performed.
Empty the tank and rell it, dissolving the descaling solution in a full tank of water.
Place a large container beneath the steam spout.
Turn the knob until the position is reached. Dispense the descaling solution into the container for 15 seconds.
Empty the container with the used descaling solution.
Press the button to turn off the machine. After 10 minutes, turn on the machine again.
Repeat steps 3 - 7 until all the descaling solution in the tank has been dispensed.
Rinse and ll the tank with fresh drinking water.
Turn the knob until the position is reached to empty the water tank. When this operation is completed, turn the knob until it is in the rest position ( ). 14
Press the hot water button for 6 seconds to disable the descaling alarm.
Fill the tank again with fresh drinking water.
Once descaling has been performed: 1. Install the Aqua Prima lter, if available; 2. Prime the circuit as described on page 7, from step 7.

CLEANING AND MAINTENANCE

HOW TO CLEAN THE MACHINE
The machine must be cleaned at least once a week. Do not immerse the machine in water or place any of its parts in a dishwasher. Do not use alcohol, solvents, benzene and/or abrasive objects to clean the machine. The water left in the tank for several days must be disposed of. Do not dry the machine and/or its components using a microwave and/or conventional oven.
Turn off the machine and unplug it.
Remove the lter, if tted, and wash the water tank.
Remove the drip tray and wash it under running water.

Remove the dregs drawer.

Empty the coffee grounds and the residual liquids separately. Wash all containers.
Remove and wash the steam spout. Wash all external components.
8 If the dregs drawer is emptied with the machine turned off, or when the alarm light to empty the dregs drawer is not on (see page 9), the count of the coffee portions contained in the dregs drawer is not restarted. For this reason, the alarm light to empty dregs drawer may illuminate even when it is not full.
Remove and wash the handgrip.
Before lling the coffee bean hopper, clean it using a soft wet cloth.
17 CLEANING THE BREW GROUP
The Brew Group must be cleaned at least once a week. Before removing the Brew Group, remove the dregs drawer as shown in g. 4 on page 16. Once you have washed and inserted the Brew Group, insert the dregs drawer and close the service door. 2 3
Press the PUSH button to remove the group.
Wash the Brew Group with running water. Wash lters carefully.
Make sure the group is in rest position; the two references must match.

Make sure the components are in the correct position. The hook shown must be in the correct position; to check its position, rmly press the PUSH button. 7
The lever on the rear part of the group must be in contact with the Brew Group base.
Insert the washed and dried Brew Group. DO NOT PRESS THE PUSH BUTTON.
Insert the dregs drawer and close the service door.

TROUBLESHOOTING

PROBLEMS CAUSES
The plug has not been plugged into the back of the machine.

SOLUTIONS

Insert the plug into the machines power socket. Warm the cups with hot water. Clean the hole of the steam spout using a pin. Change coffee blend.
The machine does not turn on.
The machine is not connected to the Connect the machine to the power power source. source.
Coffee is not hot enough. Hot water or steam is not dispensed. Coffee has little crema. The machine takes a long time to warm up or the amount of water dispensed from the spout is too little.
The cups are cold. The hole of the steam spout is clogged. The coffee blend is unsuitable or coffee is not freshly roasted.
The machine circuit is obstructed by Descale the machine. limescale build-up.
The Brew Group does not come out. The Brew Group is out of place.
Turn the machine on. Close the service door. The Brew Group is automatically placed in the correct position. Remove the dregs drawer rst, then the brew group. Fill the water tank and prime the circuit again. Clean the Brew Group. Prime the circuit again by dispensing water from the steam spout.
Dregs drawer is inserted. Coffee is not brewed. Water tank is empty. Brew group is dirty. Circuit is not primed.
Knob to adjust the quantity of coffee Turn the knob clockwise. per cup is in wrong position. Coffee is brewed slowly. Coffee is too ne. Circuit is not primed. Brew Group dirty. Coffee leaks out of the dispensing head. Brewing does not start. Dispensing head is clogged. Coffee bean hopper cover is in wrong position. Change coffee blend. Prime the circuit again by dispensing water from the spout. Clean the Brew Group. Clean the dispensing holes with a soft cloth. Correctly place the cover on the coffee bean hopper and press it rmly.
Please contact the service centre for any problems not covered in the above table or when the suggested solutions do not solve the problem.

SAFETY RULES

IN CASE OF EMERGENCY
Immediately unplug the cable from the outlet.

USE THE APPLIANCE ONLY

Indoors. To prepare coffee, dispense hot water, froth milk or heat beverages using steam. For domestic use only. By adults in non altered psycho-physical conditions.

NEVER USE THE APPLIANCE

For purposes other than those indicated above, in order to avoid danger. Do not introduce any substances other than those indicated in the instruction manual. During the normal lling of any reservoirs, all nearby reservoirs must be closed. Fill the water tank only with fresh drinking water: Hot water and/or any other liquid may damage the machine. Do not use carbonated water. Do not put ngers or any material other than coffee beans in the coffee grinder. Before manipulating the coffee grinder, turn off the machines main switch and unplug the cable.

POWER CONNECTION

Only connect the coffee machine to a suitable power socket. The voltage must correspond to the indication on the machines label.
Choose a level surface. Do not place on heated surfaces! Allow a distance of 10 cm (4 in) between walls and cooking hotplates. Do not keep the machine at temperatures below 0C (32F) danger of freezing damage. There must be easy access to the socket at all times. The power cable must not be damaged, tied up with clamps, placed on very hot surfaces, etc. The power cable must not hang. (Danger of tripping or dropping the appliance). Do not use the power cable to carry or pull the coffee machine.

DANGER

The appliance must not be used by children and persons who have not been informed on its operation. The appliance is dangerous to children. If left unattended, please disable it. Do not leave the coffee machine packaging within the reach of children. Never direct the jet of hot water and/or steam towards yourself or others. Danger of scalding. Do not insert objects through the appliances openings (Danger! Electrical current!). Do not touch the plug with wet hands and feet. Do not remove the plug by pulling the cable. Warning, danger of burns caused by hot water, steam and hot water/steam spout.

FAILURES

- Do not use the appliance in case of sure or suspected faults such as after falls. - Any repairs must be performed by an authorized customer service centre. - Do not use the appliance with a defective power cable. If damaged, the power cable must be replaced by the manufacturer or authorized service centre. (Caution! Electrical current). - Turn off the appliance before opening the service door.

CLEANING / DESCALING

- Before cleaning, unplug the machine and let the appliance cool. - Keep the appliance from coming into contact with splashes of water or immersing in water. - Do not dry the machines parts in conventional or microwave ovens.

SPARE PARTS DISPOSAL

For safety reasons, use only original spare parts and original accessories.
- The packing materials can be recycled. - Appliance: unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility. This product complies with EU Directive 2002/96/EC.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city ofce, your household waste disposal service or the retailer where you purchased the product.

TECHNICAL DATA

Nominal voltage Power rating Power supply Shell material Size (w x h x d) Weight Cable length Control panel Water tank Pump pressure (bars) Boiler Coffee bean hopper capacity Quantity of ground coffee Dregs drawer capacity Safety devices See label on the appliance See label on the appliance See label on the appliance ABS - Thermoplastic 290 x 370 x 385 mm - 11.41 x 14.57 x 15.18 in 8 Kg - 17.63 lbs 1200 mm - 47.24 in Front 1,5 liters - 50.72 oz / Removable 15 Stainless steel 180 grams - 6.35 oz / coffee beans 8,5 grams / 0.30 oz. 14 Boiler pressure safety valve Double safety thermostat.
Subject to engineering and manufacturing changes due to technological developments. The machine conforms to the European Directive 89/336/EEC (Italian Legislative Decree 476 dated 04/12/92) concerning electromagnetic compatibility.
Saeco International Group S.p.A. Via Torretta, 240 I-40041 Gaggio Montano, Bologna Tel: + 771111 Fax: + 31025 www.saeco.com
The manufacturer reserves the right to change the features of the product without prior notice. Le producteur se rserve le droit dapporter toutes modifications sans pravis. Saeco International Group S.p.A.

Updated 4/04/08

Odea Go
Esp. E74102 Rev. 01 Brew Group Esp. E90042 Rev.02

SAECO No.

SUP031O Odea Go E74102 Rev.01 Cod 10001592 MANUAL INSTRUCTIONS SAECO P0049/A GB/F Brush, Cleaning Grinder Adjustment Key, Black Cord, Electrical UPPER TECHMATE INSERT FOR BOX P0049 LOWER TECHMATE INSERT FOR BOX P0049 Box, Odea Water Tank, Odea Filter, Water Tank O-Ring, Metric, Epdm, 0019-10 Spring, Water Tank Valve P0049 Valve, Insert, Water Tank Valve, Water Tank, Lid, Duckbill Valve, Blk Lid, Water, Odea Pin Assy, Mounting Plate Black Wheel, Casing Bottom Cover, Silver Knob, Steam-Water, Odea Go SILVER PLATE LOGO SAECO NEW P0049/P0053 BLACK PLATE WITH LOGO ODEA P0049 GO Right Side Casing Left Side Casing Dump Box, Black Drip Tray, Brew Group CUP SOCKET EN 60320 C 13 Switch, SAIA 3292 Outlet Cover, Water Tank Bean Hopper Lid, Bean, Odea Giro BLACK POWER BOARD PROTECTION P0049 Power Board, I/O MAGNET FOR FLOAT SUPERAUTOM. SPRING FOR LOCK P0049 BLACK DOOR PIN P0049 Right Side Door, Odea Giro BLACK INSIDE COVER DOOR P0049 CARBONA ON-OFF BUTTON INSERT P0049 Switch, On/Off, Odea Go BLACK CAP FOR CONNECTIONS P0049/P0053 Transplate, Infrared Spring, Folk, Italia STEAM TUBE WASHER P0049 Brush, Steam Knob, Black BLACK REED SENSOR SUPPORT P0049 SILICONE GREASE CONFECTIONS SPRING FOR ON-OFF BUTTON P0049 2POLES CONNECTOR SENSOR REED DOOR P0049 SCREW PT TORX 3X10 WN 1411 GALVANIZ

Special Order No.

Yellow = Not Available unless Special Ordered
49 N/A 183921950 N/A N/A 11004374 N/A N/A N/A N/A 11003968 N/A N/A N/A 11004578 N/A N/A 11004378 N/A N/A 11005287 N/A N/A N/A N/A N/A 15000721

13000123 13000122

11004142 11004907

12000280

11002842 9161.11001340 s/n 9006SA1501.11003889 129912702

From s/n 9007SA40240634

Rev. 01-11/12/06 Brew Group Rev.02
SUP031O Odea Go E74102 Rev.01 Cod 10001592 Nut, Regulation, Lens, Dispenser, Amber Dispenser Cover, Front, Silver Dispenser Cover, Inner,Transp. Dispenser Cover, Rear, Silver Support, Electrical Card, GO Button, Blk, Alarm P0049 BLACK GEAR Z=19 FOR P0049 Button,Blk, P0049 BLACK SUPPORT FOR RING NUT P0049 Button, Blk, Stream SPRING FOR BUTTONS P0049 BLACK COFFEE BUTTON SPACER P0049/A
KIT SPARES CPU P0049 + FAUCET BOARD 3SEN with part # 24 tab
N/A 11004388 N/A 11001353 N/A N/A N/A N/A 11001438 N/A 11001364 N/A 11004185

11001758

CPU Support, Black, CPU BLACK DRIP TRAY GUIDE LID P0049 Support Drip Tray, Silver PIN WITH BLACK INSERT ASSY.P0049 Bracket,Spring Drip Tray,Blk Support, Drip Tray Spring, Drip Tray, P0049 BLACK DRIP TRAY GUIDE P0049 REINFORCEMENT Grate, Drip Tray Drip Tray, Odea Giro Float, Drip Tray, Odea
UP TO S/N. 9006SA40301265 FROM S/N. 9006SA40301266

From s/n 9007SA40330038

11001294
SUP031O Odea Go E74102 Rev.01 Cod 10001592 2POLES CONNECTOR PUMP P0049 UL 100-120V O-Ring, Epdm, 2031 Pump, Ulka, 120V, 60Hz Pump Support, Black Fitting, 90o, Pump Inlet Antidisturbance Filter Tube, Silicone, D=8x10 6-Pole Connector, Flowmeter Board, Water Level Sensor BLACK TURBINE SUPPORT/V2 P0049 Turbine Assy Tube, Silicone, 5x10, L=156 Thermostat, 175o, Sirius THERMOSTATES SPRING FOR BOILER Boiler Assy, 120V Temp Sensor, L=280mm Cover, Upper Steam Tube, Chrom Cover, Lower Steam Tube, Chrom Screw, M3x12, Torx, Uni 9786 Steam Tube Assy, P0049 Handgrip, Steam Wand Internal Tube, Pannarello Pannarello, Black Spares Kit, CPU P0049 Up to s/n 9006SA40301265 PCB,Valve, Stm/Water V1-V5 FROM S/N. 9006SA40301266 Spring, Fork, Faucet P0049 Faucet, Tea/Brass, P0049 O-ring, Or=2012 O-ring, 108, FDA, 70 SH Faucet Shaft Assy Straight Connector, Faucet Bod Connector, Faucet Body Faucet Body, Brass Tube Clamp, Oetiker same P.N. with Odea Giro BLACK CONNECTOR FOR PIN BOILER P0049 Oetiker clip D=9 SAFETY VALVE 16-18 BAR P0049 ASSY. PUMP DESCARGING WATER CONNECTION P0049 DESCARGING WATER CONNECTOR SPRING P0049 Faucet, Body Insert, P0049/A Steel Bracket, Pump Support Screw, M4x8, Uni 8112, Tcb Screw, M5X30,UNI,7688,ZNP SUPPORT FOR BOILER-FAUCET-VALVE P0049 SCREW PT TORX 3X10 WN 1411 GALVANIZ Water Connection, Milk Island Faucet Assembly With part #25,26,27,28,29,30,31,32 Boiler,Alum, P0049/A 120V

N/A N/A NV99099 JSN/A 16000190 N/A 12000361 N/A N/A N/A N/A N/A 11005774 11005668

11003670

11001751

11001629 11005003

11001332 129912702
SUP031O Odea Go E74102 Rev.01 Cod 10001592 Worm Gear, Grinder, 5P/7P Support,Upper Grinder O-Ring, Metric, Epdm, 0530-15 Grinder Burr, Ceramic, Sirius Pin,Steel M4-M6 LOWER GRINDER SUPPORT COFFEEGRINDER Bearing, Axial EKKO 342.35252 Felt Ring,45,4x39,4x4 Preground Chute Gasket, Dosing Chamber Gear, Grinder Motor Motor, Coffeegrinder/Assy 120V CAP FOR WORM SCREW MC/V3 CENTRING PANELVIT TCB SCREW 3,5X25 D.7505 ZN Bushing Insulator,Grinder Mot. same P.N. with Odea Giro Screw, M3.5x18, Din 7505, Zinc UPPER GEAR SUPPORT COFFEEGRINDER P124 BLACK INSERT FOR COFFEE GRINDER P0049 COFFEE GRINDING ADJUSTMENT GEAR P0049 GRINDER REGULATION SPRING P124 LOWER GEAR SUPPORT COFFEEGRINDER P124 SWITCH+SOCKET POWER CABL.SUPP.SMART CRINKLE WASHER 21,8X15,8X0,2 RADIAL BEARING 61900.2RS1 Electronic Board, With Sensor Support,Rubber Blk,Coff Grind Sensor Support, Grinder Motor GALVAN.FLAT WASH.DI=4,3 DE=14 SP=1,5 Nut, Self-Lock, M4 Din 982 Cover, Grinder, (Soundproof) 5-Pole Connector General Motory Assy
127473603 N/A N/A N/A 80001013 N/A N/A N/A N/A N/A N/A N/A N/A 149199050 N/A 11005658 11005606

149198350

149214800 129661702

128381800 123030200

128381902
SUP031O Odea Go E74102 Rev.01 Cod 10001592 Housing Assy, Boiler Valve Spring, Boiler Pin Cap, For Pin, For Boiler P119 Viton Seal, For Piston O-Ring, Silicone, 2015 O-Ring, Silicone, 0090-20 O-Ring, Silicone, 0060-20 Needle valve, L=20 Clip, Hairpin, Teflon Tube Pin For Boiler Lever, Boiler, Magic Deluxe O-Ring, Silicone, 0050-20 Screw K, 35x12 Win1423 Galv. Black Cover Vain Boiler P0049 Cover, Mounting Plate, Blk Ratiomotor Assy Antivibration, BrewDrive Motor SINTERED BUSH FOR MOTOR Washer, Vspressso, D=5 BLACK MICROSWITCH SUPPORT DUMP BOX P0049 Switch, Brew/Dump, Magic Kit, Gears, Ratiomotor Washer, Brew Drive Motor, Myla Coffee Dispensing Valve Assy Coffee Dispensing Valve Assy Reed Sensor, 100-120V Brew Group, 8 Gram, Primea
140328059 NMNMN/A 148380200 N/A NE11002145

9121.046 11001331

UP TO S/N. 9006SA40292687 FROM S/N. 9006SA40292688 SEE.EXPL. E90042
SUP031O Odea Go Brew Group E90042 Cod 1002145 SVS Valve, Primea Touch Plus SS.SCREW AUT.TCB 2,9X19 DIN 7981 C Tube For Piston Brew Group Black Counter Piston Brew Grou O-Ring, Silicone, 0320-40 Filter Screen, Brew Unit Spare Sleeve Unit Black WATER INLET SLEEVE BLACK O-Ring, Epdm, 2025 BLACK REAR PLATE FOR BREW UNIT SMART Screw, M2.9x9.5, Din 7982 Bale, Brew Group, Smart Drilled Black For Unit Grey ELBOW SHAFT FOR UNIT BLACK BLACK COUPLING PLATE BREW UNIT SMART BLACK HOPPER DOSER BREW UNIT SMART1 SCREW AUT.TCB 2,9X9,5 DIN 7981 C BLACK HOPPER BLOCKING PLATE UNIT SMART SPRING HOPPER SMART GROUP SCRAPER FOR BREW UNIT SMART SPRING FOR UNIT SCRAPER SPRING FOR PISTON BUSH FOR PISTON NEUTRAL BLACK INTEGRAL PISTON UNIT P124 8GR.ASS BLACK COFFEE CONTAINER UNIT 8GR.P124 ASS BLACK CONNECTING ROD FOR UNIT P124 8GR. FRONT PLATE FOR BREW UNIT SMART SS.SCREW AUT.TCB 3,5X19 DIN 7981 C Brew Group, 8 Gram, Primea